IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 8ee1b439b1540ae543149b15a2a61b9dff937d91 ]
For some reason, we add an offset to the PDI, presumably to skip the
PDI0 and PDI1 which are reserved for BPT.
This code is however completely wrong and leads to an out-of-bounds
access. We were just lucky so far since we used only a couple of PDIs
and remained within the PDI array bounds.
A Fixes: tag is not provided since there are no known platforms where
the out-of-bounds would be accessed, and the initial code had problems
as well.
A follow-up patch completely removes this useless offset.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20240326090122.1051806-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e199bf52ffda8f98f129728d57244a9cd9ad5623 upstream.
If bus is marked as multi_link, but number of masters in the stream is
not higher than bus->hw_sync_min_links (bus->multi_link && m_rt_count >=
bus->hw_sync_min_links), bank switching should not happen. The first
part of do_bank_switch() code properly takes these conditions into
account, but second part (sdw_ml_sync_bank_switch()) relies purely on
bus->multi_link property. This is not balanced and leads to NULL
pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Call trace:
wait_for_completion_timeout+0x124/0x1f0
do_bank_switch+0x370/0x6f8
sdw_prepare_stream+0x2d0/0x438
qcom_snd_sdw_prepare+0xa0/0x118
sm8450_snd_prepare+0x128/0x148
snd_soc_link_prepare+0x5c/0xe8
__soc_pcm_prepare+0x28/0x1ec
dpcm_be_dai_prepare+0x1e0/0x2c0
dpcm_fe_dai_prepare+0x108/0x28c
snd_pcm_do_prepare+0x44/0x68
snd_pcm_action_single+0x54/0xc0
snd_pcm_action_nonatomic+0xe4/0xec
snd_pcm_prepare+0xc4/0x114
snd_pcm_common_ioctl+0x1154/0x1cc0
snd_pcm_ioctl+0x54/0x74
Fixes: ce6e74d008ff ("soundwire: Add support for multi link bank switch")
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231124180136.390621-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c40d6b3249b11d60e09d81530588f56233d9aa44 ]
The soundwire subsystem uses two completion structures that allow
drivers to wait for soundwire device to become enumerated on the bus and
initialised by their drivers, respectively.
The code implementing the signalling is currently broken as it does not
signal all current and future waiters and also uses the wrong
reinitialisation function, which can potentially lead to memory
corruption if there are still waiters on the queue.
Not signalling future waiters specifically breaks sound card probe
deferrals as codec drivers can not tell that the soundwire device is
already attached when being reprobed. Some codec runtime PM
implementations suffer from similar problems as waiting for enumeration
during resume can also timeout despite the device already having been
enumerated.
Fixes: fb9469e54fa7 ("soundwire: bus: fix race condition with enumeration_complete signaling")
Fixes: a90def068127 ("soundwire: bus: fix race condition with initialization_complete signaling")
Cc: stable@vger.kernel.org # 5.7
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Rander Wang <rander.wang@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230705123018.30903-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e557bca49b812908f380c56b5b4b2f273848b676 ]
In typical use cases, the peripheral becomes pm_runtime active as a
result of the ALSA/ASoC framework starting up a DAI. The parent/child
hierarchy guarantees that the manager device will be fully resumed
beforehand.
There is however a corner case where the manager device may become
pm_runtime active, but without ALSA/ASoC requesting any functionality
from the peripherals. In this case, the hardware peripheral device
will report as ATTACHED and its initialization routine will be
executed. If this initialization routine initiates any sort of
deferred processing, there is a possibility that the manager could
suspend without the peripheral suspend sequence being invoked: from
the pm_runtime framework perspective, the peripheral is *already*
suspended.
To avoid such disconnects between hardware state and pm_runtime state,
this patch adds an asynchronous pm_request_resume() upon successful
attach/initialization which will result in the proper resume/suspend
sequence to be followed on the peripheral side.
BugLink: https://github.com/thesofproject/linux/issues/3459
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023241.14335-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: c40d6b3249b1 ("soundwire: fix enumeration completion")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f84d41b2a083b990cbdf70f3b24b6b108b9678ad ]
SoundWire device status can be incorrectly updated without
proper mask, fix this by adding a mask before updating the status.
Fixes: c7d49c76d1d5 ("soundwire: qcom: add support to new interrupts")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230525133812.30841-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 490937d479abe5f6584e69b96df066bc87be92e9 upstream.
The 'qcom_swrm_ctrl->pconfig' has size of QCOM_SDW_MAX_PORTS (14),
however we index it starting from 1, not 0, to match real port numbers.
This can lead to writing port config past 'pconfig' bounds and
overwriting next member of 'qcom_swrm_ctrl' struct. Reported also by
smatch:
drivers/soundwire/qcom.c:1269 qcom_swrm_get_port_config() error: buffer overflow 'ctrl->pconfig' 14 <= 14
Fixes: 9916c02ccd74 ("soundwire: qcom: cleanup internal port config indexing")
Cc: <stable@vger.kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202305201301.sCJ8UDKV-lkp@intel.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230601102525.609627-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2367e0ecb498764e95cfda691ff0828f7d25f9a4 ]
There are two issues related to the number of ports coming from
Devicetree when exceeding in total QCOM_SDW_MAX_PORTS. Both lead to
incorrect memory accesses:
1. With DTS having too big value of input or output ports, the driver,
when copying port parameters from local/stack arrays into 'pconfig'
array in 'struct qcom_swrm_ctrl', will iterate over their sizes.
2. If DTS also has too many parameters for these ports (e.g.
qcom,ports-sinterval-low), the driver will overflow buffers on the
stack when reading these properties from DTS.
Add a sanity check so incorrect DTS will not cause kernel memory
corruption.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230222144412.237832-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bd934f77eeac377e81ddac8673803e7334b82d3d upstream.
According to the comment and to downstream sources, the
SWRM_CONTINUE_EXEC_ON_CMD_IGNORE in SWRM_CMD_FIFO_CFG_ADDR register
should be set for v1.5.1 and newer, so fix the >= operator.
Fixes: 542d3491cdd7 ("soundwire: qcom: set continue execution flag for ignored commands")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230222140343.188691-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0603a47bd3a8f439d7844b841eee1819353063e0 ]
If wait_for_completion_timeout() times-out in _cdns_xfer_msg() it
is possible that something could have been written to the RX FIFO.
In this case, we should drain the RX FIFO so that anything in it
doesn't carry over and mess up the next transfer.
Obviously, if we got to this state something went wrong, and we
don't really know the state of everything. The cleanup in this
situation cannot be bullet-proof but we should attempt to avoid
breaking future transaction, if only to reduce the amount of
error noise when debugging the failure from a kernel log.
Note that this patch only implements the draining for blocking
(non-deferred) transfers. The deferred API doesn't have any proper
handling of error conditions and would need some re-design before
implementing cleanup. That is a task for a separate patch...
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221202161812.4186897-4-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 827c32d0df4bbe0d1c47d79f6a5eabfe9ac75216 ]
The response_buf was declared much larger (128 entries) than the number
of responses that could ever be written into it. The Cadence IP is
configurable up to a maximum of 32 entries, and the datasheet says
that RX_FIFO_AVAIL can be 2 larger than this. So allow up to 34
responses.
Also add checking in cdns_read_response() to prevent overflowing
reponse_buf if RX_FIFO_AVAIL contains an unexpectedly large number.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221202161812.4186897-3-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cbfee2e2e40d2be54196362a845a3ea0a3f877d ]
The command FIFOs in the Cadence IP can be configured during design
up to 32 entries, and the code in cadence_master.c was assuming the
full 32-entry FIFO. But all current Intel implementations use an 8-entry
FIFO.
Up to now the longest message used was 6 entries so this wasn't
causing any problem. But future Cirrus Logic codecs have downloadable
firmware or tuning blobs. It is more efficient for the codec driver to
issue long transfers that can take advantage of any queuing in the
Soundwire controller and avoid the overhead of repeatedly writing the
page registers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Fixes: 2f52a5177caa ("soundwire: cdns: Add cadence library")
Link: https://lore.kernel.org/r/20221202161812.4186897-2-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8444560b4d9302a511f0996f4cfdf85b628f4ca upstream.
The HDAudio ASoC support relies on the set_tdm_slots() helper to store
the HDaudio stream tag in the tx_mask. This only works because of the
pre-existing order in soc-pcm.c, where the hw_params() is handled for
codec_dais *before* cpu_dais. When the order is reversed, the
stream_tag is used as a mask in the codec fixup functions:
/* fixup params based on TDM slot masks */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK &&
codec_dai->tx_mask)
soc_pcm_codec_params_fixup(&codec_params,
codec_dai->tx_mask);
As a result of this confusion, the codec_params_fixup() ends-up
generating bad channel masks, depending on what stream_tag was
allocated.
We could add a flag to state that the tx_mask is really not a mask,
but it would be quite ugly to persist in overloading concepts.
Instead, this patch suggests a more generic get/set 'stream' API based
on the existing model for SoundWire. We can expand the concept to
store 'stream' opaque information that is specific to different DAI
types. In the case of HDAudio DAIs, we only need to store a stream tag
as an unsigned char pointer. The TDM rx_ and tx_masks should really
only be used to store masks.
Rename get_sdw_stream/set_sdw_stream callbacks and helpers as
get_stream/set_stream. No functionality change beyond the rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211224021034.26635-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c30a755847c7e804e1bf755e66e3ff7b7f9367 upstream.
The bus->clk_stop_timeout member is only initialized to a non-zero value
during the codec driver probe. This can lead to corner cases where this
value remains pegged at zero when the bus suspends, which results in an
endless loop in sdw_bus_wait_for_clk_prep_deprep().
Corner cases include configurations with no codecs described in the
firmware, or delays in probing codec drivers.
Initializing the default timeout to the smallest non-zero value avoid this
problem and allows for the existing logic to be preserved: the
bus->clk_stop_timeout is set as the maximum required by all codecs
connected on the bus.
Fixes: 1f2dcf3a154ac ("soundwire: intel: set dev_num_ida_min")
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221020015624.1703950-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 49a467310dc4fae591a3547860ee04d8730780f4 ]
Reading will increase the fifo count, so check for outstanding cmd wrt.
write fifo depth to avoid overflow as read will also increase
write fifo cnt.
Fixes: a661308c34de ("soundwire: qcom: wait for fifo space to be available before read/write")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221026110210.6575-3-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f936fa7a954b262cb3908bbc8f01ba19dfaf9fbf ]
For some reason we never reinit the broadcast completion, there is a
danger that broadcast commands could be treated as completed by driver
from previous complete status.
Fix this by reinitializing the completion before sending a broadcast command.
Fixes: ddea6cf7b619 ("soundwire: qcom: update register read/write routine")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221026110210.6575-2-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6867cda906aadbce5e71efde9c78a26108b2bad ]
The call to intel_register_dai() may fail because of memory allocation
issues or problems reported by the ASoC core. In all cases, when a
error is thrown the component is not registered, it's invalid to
unregister it.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220919175721.354679-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba05b39d265bdd16913f7684600d9d41e2796745 ]
The buf passed in struct sdw_msg must only be written for a READ,
in that case the RDATA part of the response is the data value of the
register.
For a write command there is no RDATA, and buf should be assumed to
be const and unmodifable. The original caller should not expect its data
buffer to be corrupted by an sdw_nwrite().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220916103505.1562210-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ef3f2aff1267bfa6d5a90c42a30b927b8aa239b ]
This patch updates device status array range from 11 to 12 as we will
be reading status from device number 0 to device number 11 inclusive.
Without this patch we can potentially access status array out of range
during auto-enumeration.
Fixes: aa1262ca6695 ("soundwire: qcom: Check device status before reading devid")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220708104747.8722-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd29c00edd0a5dac8b6e7332bb470cd50f92e893 ]
In the SoundWire probe, we store a pointer from the driver ops into
the 'slave' structure. This can lead to kernel oopses when unbinding
codec drivers, e.g. with the following sequence to remove machine
driver and codec driver.
/sbin/modprobe -r snd_soc_sof_sdw
/sbin/modprobe -r snd_soc_rt711
The full details can be found in the BugLink below, for reference the
two following examples show different cases of driver ops/callbacks
being invoked after the driver .remove().
kernel: BUG: kernel NULL pointer dereference, address: 0000000000000150
kernel: Workqueue: events cdns_update_slave_status_work [soundwire_cadence]
kernel: RIP: 0010:mutex_lock+0x19/0x30
kernel: Call Trace:
kernel: ? sdw_handle_slave_status+0x426/0xe00 [soundwire_bus 94ff184bf398570c3f8ff7efe9e32529f532e4ae]
kernel: ? newidle_balance+0x26a/0x400
kernel: ? cdns_update_slave_status_work+0x1e9/0x200 [soundwire_cadence 1bcf98eebe5ba9833cd433323769ac923c9c6f82]
kernel: BUG: unable to handle page fault for address: ffffffffc07654c8
kernel: Workqueue: pm pm_runtime_work
kernel: RIP: 0010:sdw_bus_prep_clk_stop+0x6f/0x160 [soundwire_bus]
kernel: Call Trace:
kernel: <TASK>
kernel: sdw_cdns_clock_stop+0xb5/0x1b0 [soundwire_cadence 1bcf98eebe5ba9833cd433323769ac923c9c6f82]
kernel: intel_suspend_runtime+0x5f/0x120 [soundwire_intel aca858f7c87048d3152a4a41bb68abb9b663a1dd]
kernel: ? dpm_sysfs_remove+0x60/0x60
This was not detected earlier in Intel tests since the tests first
remove the parent PCI device and shut down the bus. The sequence
above is a corner case which keeps the bus operational but without a
driver bound.
While trying to solve this kernel oopses, it became clear that the
existing SoundWire bus does not deal well with the unbind case.
Commit 528be501b7d4a ("soundwire: sdw_slave: add probe_complete structure and new fields")
added a 'probed' status variable and a 'probe_complete'
struct completion. This status is however not reset on remove and
likewise the 'probe complete' is not re-initialized, so the
bind/unbind/bind test cases would fail. The timeout used before the
'update_status' callback was also a bad idea in hindsight, there
should really be no timing assumption as to if and when a driver is
bound to a device.
An initial draft was based on device_lock() and device_unlock() was
tested. This proved too complicated, with deadlocks created during the
suspend-resume sequences, which also use the same device_lock/unlock()
as the bind/unbind sequences. On a CometLake device, a bad DSDT/BIOS
caused spurious resumes and the use of device_lock() caused hangs
during suspend. After multiple weeks or testing and painful
reverse-engineering of deadlocks on different devices, we looked for
alternatives that did not interfere with the device core.
A bus notifier was used successfully to keep track of DRIVER_BOUND and
DRIVER_UNBIND events. This solved the bind-unbind-bind case in tests,
but it can still be defeated with a theoretical corner case where the
memory is freed by a .remove while the callback is in use. The
notifier only helps make sure the driver callbacks are valid, but not
that the memory allocated in probe remains valid while the callbacks
are invoked.
This patch suggests the introduction of a new 'sdw_dev_lock' mutex
protecting probe/remove and all driver callbacks. Since this mutex is
'local' to SoundWire only, it does not interfere with existing locks
and does not create deadlocks. In addition, this patch removes the
'probe_complete' completion, instead we directly invoke the
'update_status' from the probe routine. That removes any sort of
timing dependency and a much better support for the device/driver
model, the driver could be bound before the bus started, or eons after
the bus started and the hardware would be properly initialized in all
cases.
BugLink: https://github.com/thesofproject/linux/issues/3531
Fixes: 56d4fe31af77 ("soundwire: Add MIPI DisCo property helpers")
Fixes: 528be501b7d4a ("soundwire: sdw_slave: add probe_complete structure and new fields")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20220621225641.221170-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df6407782964dc7e35ad84230abb38f46314b245 ]
The bus sdw_drv_remove() and sdw_drv_shutdown() helpers are used
conditionally, if the driver provides these routines.
These helpers already test if the driver provides a .remove or
.shutdown callback, so there's no harm in invoking the
sdw_drv_remove() and sdw_drv_shutdown() unconditionally.
In addition, the current code is imbalanced with
dev_pm_domain_attach() called from sdw_drv_probe(), but
dev_pm_domain_detach() called from sdw_drv_remove() only if the driver
provides a .remove callback.
Fixes: 9251345dca24b ("soundwire: Add SoundWire bus type")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220610015105.25987-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aa1262ca66957183ea1fb32a067e145b995f3744 upstream.
As per hardware datasheet its recommended that we check the device
status before reading devid assigned by auto-enumeration.
Without this patch we see SoundWire devices with invalid enumeration
addresses on the bus.
Cc: stable@vger.kernel.org
Fixes: a6e6581942ca ("soundwire: qcom: add auto enumeration support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220706095644.5852-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 74da272400b46f2e898f115d1b1cd60828766919 ]
Currently timeout for autoenumeration during probe and bus reset is set to
2 secs which is really a big value. This can have an adverse effect on
boot time if the slave device is not ready/reset.
This was the case with wcd938x which was not reset yet but we spent 2
secs waiting in the soundwire controller probe. Reduce this time to
1/10 of Hz which should be good enough time to finish autoenumeration
if any slaves are available on the bus.
Reported-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220506084705.18525-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d9f2dadba698114fed97b224578c5338a36b0d9 ]
commit e38f9ff63e6d ("ACPI: scan: Do not add device IDs from _CID if _HID is not valid")
exposes a race condition on a TGL RVP device leading to a timeout.
The detailed analysis shows the RT711 codec driver scheduling a jack
detection workqueue while attaching during a spurious pm_runtime
resume, and the work function happens to be scheduled after the
manager device is suspended.
The direct link between this ACPI patch and a spurious pm_runtime
resume is not obvious; the most likely explanation is that a change in
the ACPI device linked list management modifies the order in which the
pm_runtime device status is checked and exposes a race condition that
was probably present for a very long time, but was not identified.
We already have a check in the .prepare stage, where we will resume to
full power from specific clock-stop modes. In all other cases, we
don't need to resume to full power by default. Adding the
SMART_SUSPEND flag prevents the spurious resume from happening.
BugLink: https://github.com/thesofproject/linux/issues/3459
Fixes: 029bfd1cd53cd ("soundwire: intel: conditionally exit clock stop mode on system suspend")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20220420023241.14335-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce73ef6ec67104d1fcc4c5911d77ce83288a0998 ]
HP changed the DMI identification for 2022 devices:
Product Name: HP Spectre x360 Conv 13-ap0001na
Product Name: 8709
This patch relaxes the DMI_MATCH criterion to work with all versions of this product.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Anthony I Gilea <i@cpp.in>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220304204532.54675-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75eac387a2539aa6c6bbee3affa23435f2096396 ]
link_id can be zero and if we have multiple controller instances
in a system like Qualcomm debugfs will end-up with duplicate namespace
resulting in incorrect debugfs entries.
Using bus-id and link-id combination should give a unique debugfs directory
entry and should fix below warning too.
"debugfs: Directory 'master-0' with parent 'soundwire' already present!"
Fixes: bf03473d5bcc ("soundwire: add debugfs support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210907105332.1257-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There are a few intensive changes in ALSA core side at this time that
helped the significant code reduction. Meanwhile we keep getting new
stuff, so the total size still grows...
Anyway, the below are some highlights in this development cycle.
ALSA core:
- New helpers to manage page allocations and card object with devres
- Refactoring for memory allocation with wc-pages
- A new PCM hardware flag SNDRV_PCM_INFO_EXPLICIT_SYNC for controlling
the explicit sync of the stream control; it'll be used for ASoC SOF
and non-coherent memory in future
ASoC:
- Lots of cleanups and improvements to the Intel drivers, including
some new systems support
- New support for AMD Vangoh, CUI CMM-4030D-261, Mediatek Mt8195,
Renesas RZ/G2L Mediatek Mt8195, RealTek RT101P, Renesas RZ/G2L,
Rockchip RK3568 S/PDIF
USB-audio:
- Re-organized the quirk handling and a new option quirk_flags
- Fix for a regression in 5.14 code change for JACK
- Quirks for Sony WALKMAN, Digidesign mbox
HD-audio:
- Enhanced support for CS8409 codec
- More consistent shutdown behavior with the runtime PM
- The model option can accept the PCI or codec SSID as an alias
- Quirks for ASUS ROG, HP Spectre x360
Others:
- Lots of code reduction in legacy drivers with devres helpers
- FireWire MOTU 896HD support
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmEvQxUOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9hlxAAr+mfQEuYxpBC8z/Uy/E0x+QVp3HhkiQURE3o
fTJFHp3V4KafH5YdNRg6x0xjNka1Y4/ku4Egealy5YQph0eF5AW0y/um43b08dca
HPy9SLDsmsRMxMUX41WBpGiT9vhVmFoo66YZ/azL+at8r9UV9lp9+pFg74KvxtbU
dfTywI1Y/nB8kKAPlTzOFoYiYhe8WTr79m5oLX8ZyZdO1jG20XHdgbPjgesId6sP
roKua1YsfOYyBWBtUnYx4POuAYSoe9CzJOeEUFWS/36UyP2LD5GS0YRdqHPVVmgF
mshKZ6njwjkeOnijPLs9LJkOsN7RR1ypthPpMcRShAYMza46z1p5Eg1SlVDsogAl
206sUgbjusulN5Yjki7AWW4l3fCAQDfZ0rQnMqEOfRNpG4lhCdfKZgK2Bg8WIC9l
Vm1Q0ArHHLp5MhUGorRxXXo23mABS+zrDOLdjMajHFV53TPOdARGSHUbgJzDVTLE
kcY73E4oQpphLfCeSxwDIrzOGWRozFQlvgt7/5ePbA/6BeYAyn90MZaxLEISAAx4
x3BynyyoYBTxwWY84V6zWuDOwvb1Iat0vtm0GwUb9j2OlmperSj8gbL0hWiYam7c
eOpym+g1oEPpm+MHQs77RUXS34fSrT2JeTEo6c0pJXQ/FvgGCV+z5kTpqYBM/Vbn
5mARPEg=
=fHyJ
-----END PGP SIGNATURE-----
Merge tag 'sound-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are a few intensive changes in ALSA core side at this time that
helped with significant code reduction. Meanwhile we keep getting new
stuff, so the total size still grows...
Anyway, the below are some highlights in this development cycle.
ALSA core:
- New helpers to manage page allocations and card object with devres
- Refactoring for memory allocation with wc-pages
- A new PCM hardware flag SNDRV_PCM_INFO_EXPLICIT_SYNC for
controlling the explicit sync of the stream control; it'll be used
for ASoC SOF and non-coherent memory in future
ASoC:
- Lots of cleanups and improvements to the Intel drivers, including
some new systems support
- New support for AMD Vangoh, CUI CMM-4030D-261, Mediatek Mt8195,
Renesas RZ/G2L Mediatek Mt8195, RealTek RT101P, Renesas RZ/G2L,
Rockchip RK3568 S/PDIF
USB-audio:
- Re-organized the quirk handling and a new option quirk_flags
- Fix for a regression in 5.14 code change for JACK
- Quirks for Sony WALKMAN, Digidesign mbox
HD-audio:
- Enhanced support for CS8409 codec
- More consistent shutdown behavior with the runtime PM
- The model option can accept the PCI or codec SSID as an alias
- Quirks for ASUS ROG, HP Spectre x360
Others:
- Lots of code reduction in legacy drivers with devres helpers
- FireWire MOTU 896HD support"
* tag 'sound-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (421 commits)
ASoC: Revert PCM trigger changes
ALSA: usb-audio: Add lowlatency module option
ALSA: hda/cs8409: Initialize Codec only in init fixup.
ALSA: hda/cs8409: Ensure Type Detection is only run on startup when necessary
ALSA: usb-audio: Work around for XRUN with low latency playback
ALSA: pcm: fix divide error in snd_pcm_lib_ioctl
ASoC: soc-pcm: test refcount before triggering
ASoC: soc-pcm: protect BE dailink state changes in trigger
ASoC: wcd9335: Disable irq on slave ports in the remove function
ASoC: wcd9335: Fix a memory leak in the error handling path of the probe function
ASoC: wcd9335: Fix a double irq free in the remove function
ALSA: hda: Disable runtime resume at shutdown
ASoC: rockchip: i2s: Add support for frame inversion
ASoC: dt-bindings: rockchip: Add compatible strings for more SoCs
ASoC: rockchip: i2s: Add compatible for more SoCs
ASoC: rockchip: i2s: Make playback/capture optional
ASoC: rockchip: i2s: Fixup config for DAIFMT_DSP_A/B
ASoC: dt-bindings: rockchip: Document reset property for i2s
ASoC: rockchip: i2s: Fix regmap_ops hang
ASoC: rockchip: i2s: Improve dma data transfer efficiency
...
The duration of the hw_reset is defined as 4096 cycles. The Cadence IP
allows for an additional delay which doesn't seem necessary in
practice: the actual reset sequence duration is defined by the sync_go
mechanism, not by the IP itself.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818030130.17113-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel stress tests reported issues with the clock stop mode,
specifically when trying to do a system suspend while the link is
already pm_runtime suspended.
In this case, we need to disable the shim wake, but when the PCI
parent device is also pm_runtime suspended the SHIM registers are not
accessible.
Since this is an invalid corner case, this patch suggests a pm_runtime
resume of the entire bus to full power (parent+child devices) before
the system suspend so that the shim wake can be disabled.
Unlike the suspend operation, the .prepare callbacks are propagated
from root device to leaf devices. By adding a .prepare callback at the
SoundWire link level, we can double-check the pm_runtime status of the
device as well as its parent PCI device. When the problematic
configuration is detected, the device is pm_runtime resumed - which by
construction also resume its parent.
An additional loop is added to resume all child devices. In theory we
only need to restart the link, but doing so will also cause the
physical devices to synchronize and re-initialize, while their Linux
devices remain pm_runtime suspended. It's simpler to make sure the
codec devices are fully resumed so that we don't have to deal with
zombie states.
This additional loop could have been avoided by adding a .prepare
callback in SoundWire codec drivers. Functionally this would have been
equivalent. The rationale for implementing a loop at the link level is
only to reduce the amount of code required to deal at the codec level
with an Intel corner case - in other words keep codec drivers
independent from Intel platform-specific programming sequences.
BugLink: https://github.com/thesofproject/linux/issues/2606
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SoundWire Linux devices are created purely based on information
provided by platform firmware (e.g. ACPI DSDT table). When the kernel
finds a matching driver for the device address (_ADR), the probe will
initialize required data structures and initialize pm ops.
When the SoundWire link is started at a later point, the physical
devices will synchronize on the SoundWire frames and report their
attachment status, thereby triggering the enumeration and
initialization of device registers.
This two-step solution was a conscious design decision to allow e.g. a
driver to use sideband mechanisms to turn power rails on. This can
also allow OEMs to describe multiple platforms with the same DSDT
table, the devices that are not physically present in hardware.
The drawback of this approach is a bit of confusion, with more devices
than are actually present in hardware. This results in 'ghost'
devices, for which the driver successfully probes, but that will not
generate any traffic on the bus. suspend-resume transitions are
handled by drivers, and skipped when the devices are not physically
present.
This patch provides a work-around for a second-level of confusion in
platform firmware: some platforms only use HDaudio links, but
nevertheless expose SoundWire 'ghost' devices. This results in error
messages in the Intel driver while trying to suspend/resume these
links. The simplest solution is to add a boolean status flag to skip
all suspend/resume/wake sequences if the link was never started.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The power down sequence sets the link_up flag as false outside of the
mutex_lock. This is potentially unsafe.
In additional the flow in that sequence can be improved by first
testing if the link was powered, setting the link_up flag as false and
proceeding with the power down. In case the CPA bits cannot be
cleared, we only flag an error since we cannot deal with interrupts
any longer.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210818024954.16873-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
shim base and alh base are platform-dependent. Adding these two
parameters allows us to use different shim/alh base for each
platform.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210723115451.7245-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Those Intel sdw registers will be used by ASoC SOF drivers in the
following commits. So move those definitions to sdw_intel.h and it can
be visible to SOF drivers.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210723115451.7245-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we set a source PDI, the target PDI parameters will be overridden
by the source register values. The loopback streams can be
independently enabled on each link.
While the loopback source and target can be configured before any
stream is active on each link, the loopback stream should only be
prepared/triggered when the playback stream is prepared. Otherwise all
registers might be programmed to their reset values and the loopback
will not succeed. The SoundWire bus driver currently does not allow
two streams to be triggered at the same time, so the playback will
have to be started first, and later the loopback.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-11-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For debug, it's interesting to create a loopback stream for each link
and use debugfs to set a source and target PDI. The target PDI would
need to be an RX port and use the same register configurations as the
source PDI. This capability allows e.g. for the headphone playback
stream to be snooped on the headset capture stream, or alternatively
for the addition of a dedicated loopback stream, in addition of
regular capture for that link.
This patch only adds the debugfs part, the port/PDI handling will be
handled in the next patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-10-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Mockup devices don't take part in command/control operations and their
virtual ports shall not be programmed.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All read and writes from/to SoundWire mockup devices will return
-ENODATA/Command_Ignored, this patch forces a Command_OK result to let
the bus perform the required configurations, e.g. for the Data Ports,
which will only have an effect on the Master side.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This change is needed for support of mockup devices, which by
construction will not provide any answer to a bank switch, but it's
also legit for regular cases.
If for some reason a device loses sync and cannot handle a bank
switch, we should go ahead anyways. The devices can always resync
later.
The only case where the error flow should be used is when there is a
Command_Aborted composite answer from SoundWire devices.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Cadence IP exposes a small number of self-clearing bits in
the MCP_CONTROL and MCP_CONFIG_UPDATE registers.
We currently do not check that those bits are indeed cleared,
e.g. during resume operations. That could lead to resuming peripheral
devices too early.
In addition, if we happen to read these registers, update one of the
fields and write the register back, we may be writing stale data that
might have been cleared in hardware. These sort of race conditions
could lead to e.g. doing a hw_reset twice or stopping a clock that
just restarted. There is no clear way of avoiding these potential race
conditions other than making sure that these registers fields are
cleared before any read-modify-write sequence. If we detect this sort
of errors, we only log them since there is no clear recovery
possible. The only way out is likely to restart the IP with a
suspend/resume cycle.
Note that the checks are performed before updating the registers, as
well as after the Intel 'sync go' sequence in multi-link mode. That
should cover both the start and end of suspend/resume hardware
configurations. The Multi-Master mode gates the configuration updates
until the 'sync go' signal is asserted, so we only check on init and
after the end of the 'sync go' sequence.
The duration of the usleep_range() was defined by the GSYNC frequency
used in multi-master mode. With a 4kHz frequency, any configuration
change might be deferred by up to 250us. Extending the range to
1000-1500us should guarantee that the configuration change is
completed without any significant impact on the overall resume
time.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714051349.13064-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The same quirk is used for LAPBC510 and LAPBC710 skews who use the
same audio design.
These devices have the same BIOS issues inherited from the Intel
reference, add the same _ADR remap previously used on HP devices.
BugLink: https://github.com/thesofproject/linux/issues/3049
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210719233248.557923-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The ret is not used in the interrupt handler, it is just returned without
any condition or change.
We can return the IRQ_HANDLED directly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714015555.17685-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We've added quite a few filters to avoid throwing errors if a Device
does not respond to commands during the clock stop sequences, but we
missed one.
This will lead to an isolated message
[ 6115.294412] soundwire sdw-master-1: SDW_SCP_STAT bread failed:-61
The callers already filter this error code, so there's no point in
keeping it at the lower level.
Since this is a recoverable error, make this dev_err() conditional and
only log cases with Command Failed.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714014209.17357-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Sparse throws the following type of warnings:
drivers/soundwire/dmi-quirks.c:25:17: error: constant
0x000010025D070100 is so big it is long
Let's add the 'ull' suffix to make this go away and find real issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714013027.17022-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
