IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 95d7c452a26564ef0c427f2806761b857106d8c4 ]
The dev_warn to notify about a spurious interrupt was introduced with
the reasoning that these are unexpected. However spurious interrupts
tend to trigger continously and the error message on the serial console
prevents that the core's detection of spurious interrupts kicks in
(which disables the irq) and just floods the console.
Fixes: c64e7efe46b7 ("spi: stm32: make spurious and overrun interrupts visible")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240521105241.62400-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f788ba457b45b0ce422943fcec9fa35c4587764 ]
There is no need to set the DMA mapped flag of the message if it has
no mapped transfers. Moreover, it may give the code a chance to take
the wrong paths, i.e. to exercise DMA related APIs on unmapped data.
Make __spi_map_msg() to bail earlier on the above mentioned cases.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7430764f5a85d30314aeef2d5438dff1fb0b1d68 ]
Due to the reading of FIFO during the dump of data registers in
debugfs, if SPI transmission is in progress, it will be affected
and may result in transmission failure. Therefore, the dump
interface of data registers in debugfs is removed.
Fixes: 2b2142f247eb ("spi: hisi-kunpeng: Add debugfs support")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/20240416015839.3323398-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a20ad45008a7c82f1184dc6dee280096009ece55 ]
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it.
Fixes: 1ce24864bff4 ("spi: mediatek: Only do dma for 4-byte aligned buffers")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-2-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de8b6e1c231a95abf95ad097b993d34b31458ec9 ]
Return IRQ_NONE from the interrupt handler when no interrupt was
detected. Because an empty interrupt will cause a null pointer error:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
complete+0x54/0x100
hisi_sfc_v3xx_isr+0x2c/0x40 [spi_hisi_sfc_v3xx]
__handle_irq_event_percpu+0x64/0x1e0
handle_irq_event+0x7c/0x1cc
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Link: https://msgid.link/r/20240123071149.917678-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3aa619a8b4706f35cb62f780c14e68796b37f3f ]
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
Fixes: 24778be20f87 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574bf7bbe83794a902679846770f75a9b7f28176 ]
SFDP read shall use the mspi reads when using the bcm_qspi_exec_mem_op()
call. This fixes SFDP parameter page read failures seen with parts that
now use SFDP protocol to read the basic flash parameter table.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://msgid.link/r/20240109210033.43249-1-kamal.dasu@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c7bcb499840551cfbe85c6df177ebc50432bf0 ]
Documentation says only DTDL of 200 is allowed for this SoC.
Fixes: 4286db8456f4 ("spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://msgid.link/r/20231212081239.14254-1-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424a8166764e462258fdccaaefbdeb07517c8b21 ]
ZynqMP GQSPI driver no longer uses spi-master framework. It had been
converted to use spi-mem framework. So remove driver dependency from
spi-master and replace it with spi-mem.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699282435-884917-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aea672d054a21782ed8450c75febb6ba3c208ca4 ]
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: ee4d79055aee ("iio: imu: adis16475: add spi_device_id table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2ded280a4b1b7bd93e53670528504be08d24967 ]
Zynq QSPI driver has been converted to use spi-mem framework so
add spi-mem to driver kconfig dependencies.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699037031-702858-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3aa5cb264a38ae9bbcce32abca4c155af0456df ]
AHB memory as MMIO should be mapped with ioremap rather than ioremap_wc,
which should have been used initially just to handle unaligned access as
a workaround.
Fixes: d166a73503ef ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20231010201524.2021340-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb9913b511f10968a02cfa5329a896855dd152a3 ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Fix this by stop calling request_irq() with invalid IRQ #s.
Fixes: dc4dc3605639 ("spi: tegra: add spi driver for SLINK controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/tencent_73FCC06A3D1C14EE5175253C6FB46A07B709@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ec8b010979036c2fe79a64adb6ecc0bd11e91d1 ]
We don't want to use the value of ilog2(0) as dummy.buswidth is 0 when
dummy.nbytes is 0. Since we have no dummy bytes, we don't need to
configure the dummy byte bits per clock register value anyway.
Signed-off-by: "William A. Kennington III" <william@wkennington.com>
Link: https://lore.kernel.org/r/20230922182812.2728066-1-william@wkennington.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527b076ae2cb6a9c590a02725ed39399fcad1cf ]
Make sure that the device is not runtime suspended before explicitly
disabling the clocks on probe failure and on driver unbind to avoid a
clock enable-count imbalance.
Fixes: 9e3a000362ae ("spi: zynqmp: Add pm runtime support")
Cc: stable@vger.kernel.org # 4.19
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/Message-Id: <20230622082435.7873-1-johan+linaro@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ffefa1d9c9eba60c7f8b4a9ce2df3e4c7f4a88e ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-88-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 1527b076ae2c ("spi: zynqmp-gqspi: fix clock imbalance on probe failure")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18495676f7886e105133f1dc06c1d5e8d5436f32 ]
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20230906183254.235847-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f11f4202caf5710204d334fe63392052783876d ]
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20230827152558.5368-3-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 171f8a49f212e87a8b04087568e1b3d132e36a18 ]
Through empirical testing it has been determined that sometimes RX SPI
transfers with DMA enabled return corrupted data. This is down to single
or even multiple bytes lost during DMA transfer from SPI peripheral to
memory. It seems the RX FIFO within the SPI peripheral can become
confused when performing bus read accesses wider than a single byte to it
during an active SPI transfer.
This patch reduces the width of individual DMA read accesses to the
RX FIFO to a single byte to mitigate that issue.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20230827152558.5368-2-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29a449e765ff70a5bd533be94babb6d36985d096 ]
The platform_get_irq might be failed and return a negative result. So
there should have an error handling code.
Fixed this by adding an error handling code.
Fixes: 8528547bcc33 ("spi: tegra: add spi driver for sflash controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_71FC162D589E4788C2152AAC84CD8D5C6D06@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5158814cbb37bbb38344b3ecddc24ba2ed0365f2 ]
The command word is defined as following:
/* Command */
#define SPI_CMD_COMMAND_SHIFT 0
#define SPI_CMD_DEVICE_ID_SHIFT 4
#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
#define SPI_CMD_ONE_BYTE_SHIFT 11
#define SPI_CMD_ONE_WIRE_SHIFT 12
If the prepend byte count field starts at bit 8, and the next defined
bit is SPI_CMD_ONE_BYTE at bit 11, it can be at most 3 bits wide, and
thus the max value is 7, not 15.
Fixes: b17de076062a ("spi/bcm63xx: work around inability to keep CS up")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20230629071453.62024-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c1f23ad34fcdace50275a6aa1e1969b41c6233f ]
If neither a "hif_mspi" nor "mspi" resource is present, the driver will
just early exit in probe but still return success. Apart from not doing
anything meaningful, this would then also lead to a null pointer access
on removal, as platform_get_drvdata() would return NULL, which it would
then try to dereference when trying to unregister the spi master.
Fix this by unconditionally calling devm_ioremap_resource(), as it can
handle a NULL res and will then return a viable ERR_PTR() if we get one.
The "return 0;" was previously a "goto qspi_resource_err;" where then
ret was returned, but since ret was still initialized to 0 at this place
this was a valid conversion in 63c5395bb7a9 ("spi: bcm-qspi: Fix
use-after-free on unbind"). The issue was not introduced by this commit,
only made more obvious.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Link: https://lore.kernel.org/r/20230629134306.95823-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f34baf67e4d08908fd94ff29c825bb673295336 ]
n_bytes variable in the driver represents the number of bytes per word
that needs to be sent/copied to fifo. Bits/word can be between 8 and 32
bits from the client but in memory they are a power of 2, same is mentioned
in spi.h header:
"
* @bits_per_word: Data transfers involve one or more words; word sizes
* like eight or 12 bits are common. In-memory wordsizes are
* powers of two bytes (e.g. 20 bit samples use 32 bits).
* This may be changed by the device's driver, or left at the
* default (0) indicating protocol words are eight bit bytes.
* The spi_transfer.bits_per_word can override this for each transfer.
"
Hence, round of n_bytes to a power of 2 to avoid values like 3 which
would generate unalligned/odd accesses to memory/fifo.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Fixes: a51acc2400d4 ("spi: dw: Add support for 32-bits max xfer size")
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-4-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fd7c99ecf45c8ee8a9b1268f0ffc91cc6271da2 ]
The CS_TOGGLE bit when set is supposed to instruct FW to
toggle CS line between words. The driver with intent of
disabling this behaviour has been unsetting BIT(0). This has
not caused any trouble so far because the original BIT(1)
is untouched and BIT(0) likely wasn't being used.
Correct this to prevent a potential future bug.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org
Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1682412128-1913-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9728fb3ce11729aa8c276825ddf504edeb00611d ]
When all bits of IER are set to 0, we still can observe the lpspi irq events
when using DMA mode to transfer data.
So disable irq to avoid the too much irq events.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20230505063557.3962220-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5c31fb71f16ba75bad4ade208abbae225305b65 ]
The DSPI controller has configurable timing for
(a) tCSC: the interval between the assertion of the chip select and the
first clock edge
(b) tASC: the interval between the last clock edge and the deassertion
of the chip select
What is a bit surprising, but is documented in the figure "Example of
continuous transfer (CPHA=1, CONT=1)" in the datasheet, is that when the
chip select stays asserted between multiple TX FIFO writes, the tCSC and
tASC times still apply. With CONT=1, chip select remains asserted, but
SCK takes a break and goes to the idle state for tASC + tCSC ns.
In other words, the default values (of 0 and 0 ns) result in SCK
glitches where the SCK transition to the idle state, as well as the SCK
transition from the idle state, will have no delay in between, and it
may appear that a SCK cycle has simply gone missing. The resulting
timing violation might cause data corruption in many peripherals, as
their chip select is asserted.
The driver has device tree bindings for tCSC ("fsl,spi-cs-sck-delay")
and tASC ("fsl,spi-sck-cs-delay"), but these are only specified to apply
when the chip select toggles in the first place, and this timing
characteristic depends on each peripheral. Many peripherals do not have
explicit timing requirements, so many device trees do not have these
properties present at all.
Nonetheless, the lack of SCK glitches is a common sense requirement, and
since the SCK stays in the idle state during transfers for tCSC+tASC ns,
and that in itself should look like half a cycle, then let's ensure that
tCSC and tASC are at least a quarter of a SCK period, such that their
sum is at least half of one.
Fixes: 95bf15f38641 ("spi: fsl-dspi: Add ~50ns delay between cs and sck")
Reported-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Debugged-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Tested-by: Lisa Chen (陈敏捷) <minjie.chen@geekplus.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230529223402.1199503-1-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c331fd1dccfba657129380ee084b95c1cedfbef ]
It is usually better to request all necessary resources (clocks,
regulators, ...) before starting to make use of them. That way they do
not change state in case one of the resources is not available yet and
probe deferral (-EPROBE_DEFER) is necessary. This is particularly
important for DMA channels and IOMMUs which are not enforced by
fw_devlink yet (unless you use fw_devlink.strict=1).
spi-qup does this in the wrong order, the clocks are enabled and
disabled again when the DMA channels are not available yet.
This causes issues in some cases: On most SoCs one of the SPI QUP
clocks is shared with the UART controller. When using earlycon UART is
actively used during boot but might not have probed yet, usually for
the same reason (waiting for the DMA controller). In this case, the
brief enable/disable cycle ends up gating the clock and further UART
console output will halt the system completely.
Avoid this by requesting the DMA channels before changing the clock
state.
Fixes: 612762e82ae6 ("spi: qup: Add DMA capabilities")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230518-spi-qup-clk-defer-v1-1-f49fc9ca4e02@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from upstream fc96ec826bced75cc6b9c07a4ac44bbf651337ab)
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f2e981f20f92dd28983c3949702a09248c23845c.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(backported from upstream 8a5299a1278eadf1e08a598a5345c376206f171e)
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/0ce96fe96e8b07cba0613e4097cfd94d09b8919a.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87c614175bbf28d3fd076dc2d166bac759e41427 ]
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Signed-off-by: Kevin Groeneveld <kgroeneveld@lenbrook.com>
Link: https://lore.kernel.org/r/20230318222132.3373-1-kgroeneveld@lenbrook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2087e85bb66ee3652dafe732bb9b9b896229eafc ]
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c20c57d9868d7f9fd1b2904c7801b07e128f6322 ]
CPM has the same problem as QE so for CPM also use the fix added
by commit 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian"):
CPM mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for 16 and 32 bits
words. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also limit the workaround to 16 and 32 bits words because it can
only work for multiples of 8-bits.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 0398fb70940e ("spi/spi_mpc8xxx: Fix QE mode Litte Endian")
Link: https://lore.kernel.org/r/1b7d3e84b1128f42c1887dd2fb9cdf390f541bc1.1680371809.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61f49171a43ab1f80c73c5c88c508770c461e0f2 ]
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: 64ff247a978f ("spi: Add Qualcomm QUP SPI controller support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230330210341.2459548-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11951c9e3f364d7ae3b568a0e52c8335d43066b5 ]
Returning early in a platform driver's remove callback is wrong. In this
case the dma resources are not released in the error path. this is never
retried later and so this is a permanent leak. To fix this, only skip
hardware disabling if waking the device fails.
Fixes: d593574aff0a ("spi: imx: do not access registers while clocks disabled")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230306065733.2170662-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d34ff58f35c82207698f43af79817a05e1342e5 ]
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085343.2541608-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 11951c9e3f36 ("spi: imx: Don't skip cleanup in remove's error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 359f5b0d4e26b7a7bcc574d6148b31a17cefe47d ]
If devm_request_irq() fails, then we are directly return 'ret' without
clk_disable_unprepare(sfc->clk) and clk_disable_unprepare(sfc->hclk).
Fix this by changing direct return to a goto 'err_irq'.
Fixes: 0b89fc0a367e ("spi: rockchip-sfc: add rockchip serial flash controller")
Signed-off-by: Li Lanzhe <u202212060@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230419115030.6029-1-u202212060@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6a0b671880207566e1ece983bf989dde60bc1d7 ]
wait_for_completion_timeout() never returns a <0 value. It returns either
on timeout or a positive value (at least 1, or number of jiffies left
till timeout)
So, fix the error handling path and return -ETIMEDOUT should a timeout
occur.
Fixes: b0823ee35cf9 ("spi: Add spi driver for Socionext SynQuacer platform")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/c2040bf3cfa201fd8890cfab14fa5a701ffeca14.1676466072.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 811ff802aaf878ebbbaeac0307a0164fa21e7d40 ]
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 142168eba9dc ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d4bde04318c0d33705e9a77d4c7df72f262011e0 ]
Selecting a symbol with additional dependencies requires
adding the same dependency here:
WARNING: unmet direct dependencies detected for MUX_MMIO
Depends on [n]: MULTIPLEXER [=y] && OF [=n]
Selected by [y]:
- SPI_DW_BT1 [=y] && SPI [=y] && SPI_MASTER [=y] && SPI_DESIGNWARE [=y] && (MIPS_BAIKAL_T1 || COMPILE_TEST [=y])
Drop the 'select' here to avoid the problem. Anyone using
the dw-bt1 SPI driver should make sure they include the
mux driver as well now.
Fixes: 7218838109fe ("spi: dw-bt1: Fix undefined devm_mux_control_get symbol")
Fixes: abf00907538e ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Link: https://lore.kernel.org/all/20221218192523.c6vnfo26ua6xqf26@mobilestation/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230130140156.3620863-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c63b8fd14a7db719f8252038a790638728c4eb66 ]
Due to using the u16 type in the min_t() macros the SPI transfer length
will be cast to word before participating in the conditional statement
implied by the macro. Thus if the transfer length is greater than 64KB the
Tx/Rx FIFO threshold level value will be determined by the leftover of the
truncated after the type-case length. In the worst case it will cause the
dramatical performance drop due to the "Tx FIFO Empty" or "Rx FIFO Full"
interrupts triggered on each xfer word sent/received to/from the bus.
The problem can be easily fixed by specifying the unsigned int type in the
min_t() macros thus preventing the possible data loss.
Fixes: ea11370fffdf ("spi: dw: get TX level without an additional variable")
Reported-by: Sergey Nazarov <Sergey.Nazarov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230113185942.2516-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b35b173dbc1711f8d272e3f322d2ad697015919 ]
The two debug messages in spidev_open() dereference spidev->spi without
taking the lock and without checking if it's not null. This can lead to
a crash. Drop the messages as they're not needed - the user-space will
get informed about ENOMEM with the syscall return value.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a6f994f848a69deb2bf3cd9d130dd0c09730e55 ]
The addition of 3WIRE support would affect MOSI direction even
when still in standard (4 wire) mode. This can lead to MOSI being
at an invalid logic level when a device driver sets an SPI
message with a NULL tx_buf.
spi.h states that if tx_buf is NULL then "zeros will be shifted
out ... " If MOSI is tristated then the data shifted out is subject
to pull resistors, keepers, or in the absence of those, noise.
This issue came to light when using spi-gpio connected to an
ADS7843 touchscreen controller. MOSI pulled high when clocking
MISO data in caused the SPI device to interpret this as a command
which would put the device in an unexpected and non-functional
state.
Fixes: 4b859db2c606 ("spi: spi-gpio: add SPI_3WIRE support")
Fixes: 5132b3d28371 ("spi: gpio: Support 3WIRE high-impedance turn-around")
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Link: https://lore.kernel.org/r/20221207230853.6174-1-kris@embeddedTS.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dbfa445ff7393d1c4c066c1727c9e0af1251958 ]
Commit f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
has changed the user-space interface so that bogus SPI_CS_HIGH started
to appear in the mask returned by SPI_IOC_RD_MODE even for active-low CS
pins. Commit 138c9c32f090
("spi: spidev: Fix CS polarity if GPIO descriptors are used") fixed only
SPI_IOC_WR_MODE part of the problem. Let's fix SPI_IOC_RD_MODE
symmetrically.
Test case:
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/spi/spidev.h>
int main(int argc, char **argv)
{
char modew = SPI_CPHA;
char moder;
int f = open("/dev/spidev0.0", O_RDWR);
if (f < 0)
return 1;
ioctl(f, SPI_IOC_WR_MODE, &modew);
ioctl(f, SPI_IOC_RD_MODE, &moder);
return moder == modew ? 0 : 2;
}
Fixes: f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20221130162927.539512-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d10e90cee9eb57882b0f7e19fd699033722e226 ]
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db2d2dc9a0b58c6faefb6b002fdbed4f0362d1a4 ]
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a0d ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e759387788 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 804313b64e412a81b0b3389a10e7622452004aa6 ]
pci_get_device() will increase the reference count for the returned
pci_dev. Since 'dma_dev' is only used to filter the channel in
dw_spi_dma_chan_filer() after using it we need to call pci_dev_put() to
decrease the reference count. Also add pci_dev_put() for the error case.
Fixes: 7063c0d942a1 ("spi/dw_spi: add DMA support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20221116093204.46700-1-wangxiongfeng2@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62aa1a344b0904549f6de7af958e8a1136fd5228 ]
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 195583504be28df5d608a4677dd796117aea875f ]
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: ea8be08cc9358 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
