IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.
This removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts.
Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').
With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deasserted anytime. Fix the polarity and mark it as always-on.
Anyway, using the regulator is only a workaround for the missing support of
specifying a reset GPIO for USB devices in a generic way. As we don't
have a solution for this at the moment, at least fix the current
workaround.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet the typical value for VDD_SNVS should be
800 mV, so let's make sure that this is within the range of the
regulator.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It looks like the voltages for the SOC and DRAM supply weren't properly
validated before. The datasheet and uboot-imx code tells us that VDD_SOC
should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM should be
950 mV for DDR clock frequencies of up to 1.5 GHz.
Let's fix these values to make sure the voltages are within the required
range.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Nacon GX100XF is already mapped, but it seems there is a Nacon
GC-100 (identified as NC5136Wht PCGC-100WHITE though I believe other
colours exist) with a different USB ID when in XInput mode.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Link: https://lore.kernel.org/r/20211015192051.5196-1-michael@michaelcullen.name
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For proper pressure calculation we need at least x and z1 to be non
zero. Even worse, in case z1 we may run in to division by zero
error.
Fixes: 60b7db914ddd ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d3505 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
q->disk becomes invalid after the gendisk is removed. Work around this
by caching the dev_t for the tracepoints. The real fix would be to
properly tear down the I/O schedulers with the gendisk, but that is
a much more invasive change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211012093301.GA27795@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Don't switch back to percpu mode to avoid the double RCU grace period
when tearing down SCSI devices. After removing the disk only passthrough
commands can be send anyway.
Suggested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-6-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of delaying draining of file system I/O related items like the
blk-qos queues, the integrity read workqueue and timeouts only when the
request_queue is removed, do that when del_gendisk is called. This is
important for SCSI where the upper level drivers that control the gendisk
are separate entities, and the disk can be freed much earlier than the
request_queue, or can even be unbound without tearing down the queue.
Fixes: edb0872f44ec ("block: move the bdi from the request_queue to the gendisk")
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-5-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To prepare for fixing a gendisk shutdown race, open code the
blk_queue_enter logic in bio_queue_enter. This also removes the
pointless flags translation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-4-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Factor out the code to try to get q_usage_counter without blocking into
a separate helper. Both to improve code readability and to prepare for
splitting bio_queue_enter from blk_queue_enter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-3-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ensure all bios check the current values of the queue under freeze
protection, i.e. to make sure the zero capacity set by del_gendisk
is actually seen before dispatching to the driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929071241.934472-2-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
I received a build failure for a new patch I'm working on the nds32
architecture, and when I went to test it, I couldn't get to my build error,
because it failed to build with a bunch of:
Error: invalid operands (*UND* and *UND* sections) for `^'
issues with various files. Those files were temporary asm files that looked
like: kernel/.tmp_mc_fork.s
I decided to look deeper, and found that the "mc" portion of that name
stood for "mcount", and was created by the recordmcount.pl script. One that
I wrote over a decade ago. Once I knew the source of the problem, I was
able to investigate it further.
The way the recordmcount.pl script works (BTW, there's a C version that
simply modifies the ELF object) is by doing an "objdump" on the object
file. Looks for all the calls to "mcount", and creates an offset of those
locations from some global variable it can use (usually a global function
name, found with <.*>:). Creates a asm file that is a table of references
to these locations, using the found variable/function. Compiles it and
links it back into the original object file. This asm file is called
".tmp_mc_<object_base_name>.s".
The problem here is that the objdump produced by the nds32 object file,
contains things that look like:
0000159a <.L3^B1>:
159a: c6 00 beqz38 $r6, 159a <.L3^B1>
159a: R_NDS32_9_PCREL_RELA .text+0x159e
159c: 84 d2 movi55 $r6, #-14
159e: 80 06 mov55 $r0, $r6
15a0: ec 3c addi10.sp #0x3c
Where ".L3^B1 is somehow selected as the "global" variable to index off of.
Then the assembly file that holds the mcount locations looks like this:
.section __mcount_loc,"a",@progbits
.align 2
.long .L3^B1 + -5522
.long .L3^B1 + -5384
.long .L3^B1 + -5270
.long .L3^B1 + -5098
.long .L3^B1 + -4970
.long .L3^B1 + -4758
.long .L3^B1 + -4122
[...]
And when it is compiled back to an object to link to the original object,
the compile fails on the "^" symbol.
Simple solution for now, is to have the perl script ignore using function
symbols that have an "^" in the name.
Link: https://lkml.kernel.org/r/20211014143507.4ad2c0f7@gandalf.local.home
Cc: stable@vger.kernel.org
Acked-by: Greentime Hu <green.hu@gmail.com>
Fixes: fbf58a52ac088 ("nds32/ftrace: Add RECORD_MCOUNT support")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
In the big pgtable header split, I inadvertently introduced a couple of
duplicate symbols.
Fixes: fe6cb7b043b69cd9 ("ARC: mm: disintegrate pgtable.h into levels and flags")
Signed-off-by: Vineet Gupta <vgupta@kernel.org>
In `test_no_sockets` we don't expect any sockets, indeed
check_no_sockets() prints an error and exits if `sockets` list is
not empty, so free_sock_stat() call is unnecessary since it would
only be called when the `sockets` list is empty.
This was discovered by a strange warning printed by gcc v11.2.1:
In file included from ../../include/linux/list.h:7,
from vsock_diag_test.c:18:
vsock_diag_test.c: In function ‘test_no_sockets’:
../../include/linux/kernel.h:35:45: error: array subscript ‘struct vsock_stat[0]’ is partly outside array bound
s of ‘struct list_head[1]’ [-Werror=array-bounds]
35 | const typeof(((type *)0)->member) * __mptr = (ptr); \
| ^~~~~~
../../include/linux/list.h:352:9: note: in expansion of macro ‘container_of’
352 | container_of(ptr, type, member)
| ^~~~~~~~~~~~
../../include/linux/list.h:393:9: note: in expansion of macro ‘list_entry’
393 | list_entry((pos)->member.next, typeof(*(pos)), member)
| ^~~~~~~~~~
../../include/linux/list.h:522:21: note: in expansion of macro ‘list_next_entry’
522 | n = list_next_entry(pos, member); \
| ^~~~~~~~~~~~~~~
vsock_diag_test.c:325:9: note: in expansion of macro ‘list_for_each_entry_safe’
325 | list_for_each_entry_safe(st, next, sockets, list) {
| ^~~~~~~~~~~~~~~~~~~~~~~~
In file included from vsock_diag_test.c:18:
vsock_diag_test.c:333:19: note: while referencing ‘sockets’
333 | LIST_HEAD(sockets);
| ^~~~~~~
../../include/linux/list.h:23:26: note: in definition of macro ‘LIST_HEAD’
23 | struct list_head name = LIST_HEAD_INIT(name)
It seems related to some compiler optimization and assumption
about the empty `sockets` list, since this warning is printed
only with -02 or -O3. Also removing `exit(1)` from
check_no_sockets() makes the warning disappear since in that
case free_sock_stat() can be reached also when the list is
not empty.
Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20211014152045.173872-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-14
Brett ensures RDMA nodes are removed during release and rebuild. He also
corrects fw.mgmt.api to include the patch number for proper
identification.
Dave stops ida_free() being called when an IDA has not been allocated.
Michal corrects the order of parameters being provided and the number of
entries skipped for UDP tunnels.
====================
Link: https://lore.kernel.org/r/20211014181953.3538330-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Building csky:allmodconfig results in the following build errors.
arch/csky/mm/tcm.c:9:2: error:
#error "You should define ITCM_RAM_BASE"
9 | #error "You should define ITCM_RAM_BASE"
| ^~~~~
arch/csky/mm/tcm.c:14:2: error:
#error "You should define DTCM_RAM_BASE"
14 | #error "You should define DTCM_RAM_BASE"
| ^~~~~
arch/csky/mm/tcm.c:18:2: error:
#error "You should define correct DTCM_RAM_BASE"
18 | #error "You should define correct DTCM_RAM_BASE"
This is seen with compile tests since those enable HAVE_TCM,
but do not provide useful default values for ITCM_RAM_BASE or
DTCM_RAM_BASE. Disable HAVE_TCM for commpile tests to avoid
the error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guo Ren <guoren@kernel.org>
Building csky:allmodconfig results in the following build error.
In file included from ./include/linux/bitops.h:33,
from ./include/linux/log2.h:12,
from kernel/bounds.c:13:
./arch/csky/include/asm/bitops.h:77: error: "__clear_bit" redefined
Since commit 9248e52fec95 ("locking/atomic: simplify non-atomic wrappers"),
__clear_bit is defined in include/asm-generic/bitops/non-atomic.h,
and the define in the csky include file is no longer necessary or useful.
Remove it.
Fixes: 9248e52fec95 ("locking/atomic: simplify non-atomic wrappers")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guo Ren <guoren@kernel.org>
Compiling csky:allmodconfig with an upstream C compiler results
in the following error.
csky-linux-gcc: error:
unrecognized command-line option '-mbacktrace';
did you mean '-fbacktrace'?
Select ARCH_WANT_FRAME_POINTERS only if gcc supports it to
avoid the error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guo Ren <guoren@kernel.org>
gpr_get() return the entire pt_regs (include sr) to userspace, if we
don't restore the C bit in gpr_set, it may break the ALU result in
that context. So the C flag bit is part of gpr context, that's why
riscv totally remove the C bit in the ISA. That makes sr reg clear
from userspace to supervisor privilege.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
csky restore_sigcontext() blindly overwrites regs->sr with the value
it finds in sigcontext. Attacker can store whatever they want in there,
which includes things like S-bit. Userland shouldn't be able to set
that, or anything other than C flag (bit 0).
Do the same thing other architectures with protected bits in flags
register do - preserve everything that shouldn't be settable in
user mode, picking the rest from the value saved is sigcontext.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Guo Ren <guoren@kernel.org>
Cc: stable@vger.kernel.org
Commit bdb7cc643fc9 ("ipv6: Count interface receive statistics on the
ingress netdev") does not work when ip6_forward() executes on the skbs
with vrf-enslaved netdev. Use IP6CB(skb)->iif to get to the right one.
Add a selftest script to verify.
Fixes: bdb7cc643fc9 ("ipv6: Count interface receive statistics on the ingress netdev")
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211014130845.410602-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A colletion of smallish mostly driver specific fixes, the biggest thing
here is fixing some of the core code to generate change notifications
properly when writing to controls which will fix issues with UIs not
showing the correct values.
There's one build fix here with a slightly misleading changelog saying
it's adding IRQ config support, it's adding a missing select of the
regmap-irq code rather than adding a feature.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmFpaYkACgkQJNaLcl1U
h9AK1Qf8DBJ4hv+jXUB78qrymQCw1gGbZ9S+Z0TUX/GG+AquP5HbuwKvL28pjKU3
8nNqqfqcqT9wxPu5T4ct1TJishT+3lhvpsGpMU4beP3/P1RcA6asUF9ycty2EN+s
07gXTnYTUGzMl+ZXKBt9lZBpKrxn/EBh8CkJDNYTrTv9O6kaFwT9UT+h8Ogn+Blg
XGg7wveKrLjpEhwFa6HvRWiV+12kI6ZWt4JQrF2Z0bMkRNWwz14A0qybrr1FrFud
FkB1gD3PArCLv6AYTW4F8t0ldwKniJjX386yq50dOfab/iWZpcqmxou35+exhP/j
PhXnUUvAeowZGPRjEAqAcGTq3zCTqw==
=3OCP
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.15-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.15
A colletion of smallish mostly driver specific fixes, the biggest thing
here is fixing some of the core code to generate change notifications
properly when writing to controls which will fix issues with UIs not
showing the correct values.
There's one build fix here with a slightly misleading changelog saying
it's adding IRQ config support, it's adding a missing select of the
regmap-irq code rather than adding a feature.
- fix module autoloading on gpio-74x164 after a revert of OF modaliases
- fix problems with the bias setting in gpio-pca953x
- fix a use-after-free bug in gpio-mockup by using software nodes
-----BEGIN PGP SIGNATURE-----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=dOer
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix module autoloading on gpio-74x164 after a revert of OF modaliases
- fix problems with the bias setting in gpio-pca953x
- fix a use-after-free bug in gpio-mockup by using software nodes
* tag 'gpio-fixes-for-v5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: mockup: Convert to use software nodes
gpio: pca953x: Improve bias setting
gpio: 74x164: Add SPI device ID table
A few small fixes for v5.15, mostly driver specific but there's one in
the core which fixes a deadlock when adding devices on spi-mux that's
triggered because spi-mux is a SPI device which is itself a SPI
controller and so can instantiate devices when registered. We were
using a global lock to protect against reusing chip selects but they're
a per controller thing so moving the lock per controller resolves that.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmFpaEoACgkQJNaLcl1U
h9Buawf/QpqpYKY+/ZiU3VG1iYYB3zE/KNsBVGPwDHIwLWX5NRxtGupERqoHgqaR
e2Omo459vLdfShXSEuur5Co95q8nbgBxzbFYf/5/fPVmCQipWqAZ6AjJj60fpAP3
qVlXYvYrxUDfGywCkMQjLN3o+dcDxaGVG6+u1vvEnbdMt96lVbOKj2meaFpQ1jbj
faY5GR/+5ZzhvzpxY3/FV6dlwvEdMRon0k6pFLis0YvxyOvQZffRdvAI4KxiFVP9
bAIPRGyn8tbppXlVJBBncRy/aSIxijauk3xGuPmRoy7CZaVZMwlfcPJ18NGixAVG
B9f08ADBY7gAiEiJDCYX0u4ZaAOq+w==
=U/5f
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few small fixes.
Mostly driver specific but there's one in the core which fixes a
deadlock when adding devices on spi-mux that's triggered because
spi-mux is a SPI device which is itself a SPI controller and so can
instantiate devices when registered.
We were using a global lock to protect against reusing chip selects
but they're a per controller thing so moving the lock per controller
resolves that"
* tag 'spi-fix-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi-mux: Fix false-positive lockdep splats
spi: Fix deadlock when adding SPI controllers on SPI buses
spi: bcm-qspi: clear MSPI spifie interrupt during probe
spi: spi-nxp-fspi: don't depend on a specific node name erratum workaround
spi: mediatek: skip delays if they are 0
spi: atmel: Fix PDC transfer setup bug
spi: spidev: Add SPI ID table
spi: Use 'flash' node name instead of 'spi-flash' in example
Just a trivial fix to the MAINTAINERS file for an update missed during
conversion of the DT bindings to YAML format.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmFpaKIACgkQJNaLcl1U
h9CELAf/dc15I7uk2CVZ2G+60kyL0aW8AJkpUVdBBQ/BFT2feLAEIUJUO4/zE8nt
gxT9BP+IkB++j8qqfGLJ15e8mINDRA35OWyscdr/oy9rg/5ZCBBO55AGSACn5Ege
bNSXQoQw6ZUE/X/es6voecLCJjSw76pqI3NMfq6m5961Xw79vRPXPPypnlS+atDm
OSjesPtVLls/LbHowFfAeifrS0Ck8S3T/4Wha/XxoCNOPYh4yaNsuR/AMsYw5EN5
U1hobI5uU10P7u/CmUbACrbp20sS0KYXC1YzJNldDjxqCPPH/RoiskrxTyx7tPtB
F1Zs5aY/HGiyPnRuDaoHzYdcrEI8+Q==
=GYqF
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Just a trivial fix to the MAINTAINERS file for an update missed during
conversion of the DT bindings to YAML format"
* tag 'regulator-fix-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
MAINTAINERS: rectify entry for SY8106A REGULATOR DRIVER
smb2_validate_credit_charge() accesses fields in the SMB2 PDU body,
but until smb2_calc_size() is called the PDU has not yet been verified
to be large enough to access the PDU dynamic part length field.
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Ralph Boehme <slow@samba.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Add buffer validation for smb direct.
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Hyunchul Lee <hyc.lee@gmail.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
ksmbd limit read/write/trans buffer size not to exceed maximum 8MB.
And set the minimum value of max response buffer size to 64KB.
Windows client doesn't send session setup request if ksmbd set max
trans/read/write size lower than 64KB in smb2 negotiate.
It means windows allow at least 64 KB or more about this value.
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
* Qcom: Update code word value for raw reads (QPIC v2+)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmFpVGEACgkQJWrqGEe9
VoR5IggAj5dtbvVx89icuQp1yfBebZJXQGVvd06E1Btk36nic538SHnEkc3heiUZ
ySxBiN8mKI/0wgOK3PBxRoSU9XNAl32W4AmG2nQzhfgL1AL0bCKlaOVuf305ts58
SGECfEawVNbMZKH/WFwsHQBMH+d+B8oMiWgK7h694OCWQxnQSTBYKCGEB9Dzqjjd
8l0oQBTgPGOFrb3p0P+GRFbSFy+wLPIQpU9hm1HoXQxZk7K6fSkPqjTYP8FUI8Nc
bAaQTM7Y2rA2GyandlhUnEkQICu1P1MEVxh9viNYyPKb9Lu85F7mpDa8kCPxq3LS
67X9gJO+PIzvW0wy6zsSWTWC8giaGg==
=gtld
-----END PGP SIGNATURE-----
Merge tag 'mtd/fixes-for-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fix from Miquel Raynal:
"Raw NAND controller driver fix:
- Qcom: Update code word value for raw reads (QPIC v2+)"
* tag 'mtd/fixes-for-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: qcom: Update code word value for raw read
core:
- clamp fbdev size
- edid cap blocks read to avoid out of bounds
panel:
- fix missing crc32 dependency
msm:
- Fix a new crash on dev file close if the dev file was opened when
GPU is not loaded (such as missing fw in initrd)
- Switch to single drm_sched_entity per priority level per drm_file
to unbreak multi-context userspace
- Serialize GMU access to fix GMU OOB errors
- Various error path fixes
- A couple integer overflow fixes
- Fix mdp5 cursor plane WARNs
i915:
- Fix ACPI object leak
- Fix context leak in user proto-context creation
- Fix missing i915_sw_fence_fini call
hyperv:
- hide hw pointer
nouveau:
- fix engine selection bit
r128:
- fix UML build
rcar-du:
- unconncted LVDS regression fix
mediatek:
- revert CMDQ refinement patches
-----BEGIN PGP SIGNATURE-----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=Ey1r
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2021-10-15-1' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"It has a few scattered msm and i915 fixes, a few core fixes and a
mediatek feature revert.
I've had to pick a bunch of patches into this, as the drm-misc-fixes
tree had a bunch of vc4 patches I wasn't comfortable with sending to
you at least as part of this, they were delayed due to your reverts.
If it's really useful as fixes I'll do a separate pull.
Summary:
Core:
- clamp fbdev size
- edid cap blocks read to avoid out of bounds
panel:
- fix missing crc32 dependency
msm:
- Fix a new crash on dev file close if the dev file was opened when
GPU is not loaded (such as missing fw in initrd)
- Switch to single drm_sched_entity per priority level per drm_file
to unbreak multi-context userspace
- Serialize GMU access to fix GMU OOB errors
- Various error path fixes
- A couple integer overflow fixes
- Fix mdp5 cursor plane WARNs
i915:
- Fix ACPI object leak
- Fix context leak in user proto-context creation
- Fix missing i915_sw_fence_fini call
hyperv:
- hide hw pointer
nouveau:
- fix engine selection bit
r128:
- fix UML build
rcar-du:
- unconncted LVDS regression fix
mediatek:
- revert CMDQ refinement patches"
* tag 'drm-fixes-2021-10-15-1' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/panel: olimex-lcd-olinuxino: select CRC32
drm/r128: fix build for UML
drm/nouveau/fifo: Reinstate the correct engine bit programming
drm/hyperv: Fix double mouse pointers
drm/fbdev: Clamp fbdev surface size if too large
drm/edid: In connector_bad_edid() cap num_of_ext by num_blocks read
drm/i915: Free the returned object of acpi_evaluate_dsm()
drm/i915: Fix bug in user proto-context creation that leaked contexts
drm: rcar-du: Don't create encoder for unconnected LVDS outputs
drm/msm/dsi: fix off by one in dsi_bus_clk_enable error handling
drm/msm/dsi: Fix an error code in msm_dsi_modeset_init()
drm/msm/dsi: dsi_phy_14nm: Take ready-bit into account in poll_for_ready
drm/msm/dsi/phy: fix clock names in 28nm_8960 phy
drm/msm/dpu: Fix address of SM8150 PINGPONG5 IRQ register
drm/msm: Do not run snapshot on non-DPU devices
drm/msm/a3xx: fix error handling in a3xx_gpu_init()
drm/msm/a4xx: fix error handling in a4xx_gpu_init()
drm/msm: Fix null pointer dereference on pointer edp
drm/msm/mdp5: fix cursor-related warnings
drm/msm: Avoid potential overflow in timeout_to_jiffies()
...
some memory leaks and panic. Also many minor fixes.
-----BEGIN PGP SIGNATURE-----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=QUnM
-----END PGP SIGNATURE-----
Merge tag 'ntfs3_for_5.15' of git://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 fixes from Konstantin Komarov:
"Use the new api for mounting as requested by Christoph.
Also fixed:
- some memory leaks and panic
- xfstests (tested on x86_64) generic/016 generic/021 generic/022
generic/041 generic/274 generic/423
- some typos, wrong returned error codes, dead code, etc"
* tag 'ntfs3_for_5.15' of git://github.com/Paragon-Software-Group/linux-ntfs3: (70 commits)
fs/ntfs3: Check for NULL pointers in ni_try_remove_attr_list
fs/ntfs3: Refactor ntfs_read_mft
fs/ntfs3: Refactor ni_parse_reparse
fs/ntfs3: Refactor ntfs_create_inode
fs/ntfs3: Refactor ntfs_readlink_hlp
fs/ntfs3: Rework ntfs_utf16_to_nls
fs/ntfs3: Fix memory leak if fill_super failed
fs/ntfs3: Keep prealloc for all types of files
fs/ntfs3: Remove unnecessary functions
fs/ntfs3: Forbid FALLOC_FL_PUNCH_HOLE for normal files
fs/ntfs3: Refactoring of ntfs_set_ea
fs/ntfs3: Remove locked argument in ntfs_set_ea
fs/ntfs3: Use available posix_acl_release instead of ntfs_posix_acl_release
fs/ntfs3: Check for NULL if ATTR_EA_INFO is incorrect
fs/ntfs3: Refactoring of ntfs_init_from_boot
fs/ntfs3: Reject mount if boot's cluster size < media sector size
fs/ntfs3: Refactoring lock in ntfs_init_acl
fs/ntfs3: Change posix_acl_equiv_mode to posix_acl_update_mode
fs/ntfs3: Pass flags to ntfs_set_ea in ntfs_set_acl_ex
fs/ntfs3: Refactor ntfs_get_acl_ex for better readability
...
We call idle_kvm_start_guest() from power7_offline() if the thread has
been requested to enter KVM. We pass it the SRR1 value that was returned
from power7_idle_insn() which tells us what sort of wakeup we're
processing.
Depending on the SRR1 value we pass in, the KVM code might enter the
guest, or it might return to us to do some host action if the wakeup
requires it.
If idle_kvm_start_guest() is able to handle the wakeup, and enter the
guest it is supposed to indicate that by returning a zero SRR1 value to
us.
That was the behaviour prior to commit 10d91611f426 ("powerpc/64s:
Reimplement book3s idle code in C"), however in that commit the
handling of SRR1 was reworked, and the zeroing behaviour was lost.
Returning from idle_kvm_start_guest() without zeroing the SRR1 value can
confuse the host offline code, causing the guest to crash and other
weirdness.
Fixes: 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-2-mpe@ellerman.id.au
In commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in
C") kvm_start_guest() became idle_kvm_start_guest(). The old code
allocated a stack frame on the emergency stack, but didn't use the
frame to store anything, and also didn't store anything in its caller's
frame.
idle_kvm_start_guest() on the other hand is written more like a normal C
function, it creates a frame on entry, and also stores CR/LR into its
callers frame (per the ABI). The problem is that there is no caller
frame on the emergency stack.
The emergency stack for a given CPU is allocated with:
paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE;
So emergency_sp actually points to the first address above the emergency
stack allocation for a given CPU, we must not store above it without
first decrementing it to create a frame. This is different to the
regular kernel stack, paca->kstack, which is initialised to point at an
initial frame that is ready to use.
idle_kvm_start_guest() stores the backchain, CR and LR all of which
write outside the allocation for the emergency stack. It then creates a
stack frame and saves the non-volatile registers. Unfortunately the
frame it creates is not large enough to fit the non-volatiles, and so
the saving of the non-volatile registers also writes outside the
emergency stack allocation.
The end result is that we corrupt whatever is at 0-24 bytes, and 112-248
bytes above the emergency stack allocation.
In practice this has gone unnoticed because the memory immediately above
the emergency stack happens to be used for other stack allocations,
either another CPUs mc_emergency_sp or an IRQ stack. See the order of
calls to irqstack_early_init() and emergency_stack_init().
The low addresses of another stack are the top of that stack, and so are
only used if that stack is under extreme pressue, which essentially
never happens in practice - and if it did there's a high likelyhood we'd
crash due to that stack overflowing.
Still, we shouldn't be corrupting someone else's stack, and it is purely
luck that we aren't corrupting something else.
To fix it we save CR/LR into the caller's frame using the existing r1 on
entry, we then create a SWITCH_FRAME_SIZE frame (which has space for
pt_regs) on the emergency stack with the backchain pointing to the
existing stack, and then finally we switch to the new frame on the
emergency stack.
Fixes: 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-1-mpe@ellerman.id.au
Leonard Crestez says:
====================
tcp: md5: Fix overlap between vrf and non-vrf keys
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ only
in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key. This
means that adding a key with l3index != 0 after a key with l3index == 0
will cause the earlier key to be deleted. Both keys can be present if the
non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This casues
failures if the passwords differ.
This can be fixed by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer vrf-bound
keys above other considerations like prefixlen.
The fact that keys with l3index==0 affect VRF connections is usually not
desirable, VRFs are meant to be completely independent. This behavior needs
to preserved for backwards compatibility. Also, applications can just bind
listen sockets to VRF and never specify TCP_MD5SIG_FLAG_IFINDEX at all.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF". This
is what applications using VRFs for traffic separation want.
This also contains tests for the second part. It does not contain tests for
overlapping keys, that would require more changes in nettest to add
multiple keys. These scenarios are also covered by my tests for TCP-AO,
especially around this area:
https://github.com/cdleonard/tcp-authopt-test/blob/main/tcp_authopt_test/test_vrf_bind.py
Changes since V2:
* Rename --do-bind-key-ifindex to --force-bind-key-ifindex
* Fix referencing TCP_MD5SIG_FLAG_IFINDEX as TCP_MD5SIG_IFINDEX
Link to v2: https://lore.kernel.org/netdev/cover.1634107317.git.cdleonard@gmail.com/
Changes since V1:
* Accept (TCP_MD5SIG_IFINDEX with tcpm_ifindex == 0)
* Add flags for explicitly including or excluding TCP_MD5SIG_FLAG_IFINDEX
to nettest
* Add few more tests in fcnal-test.sh.
Link to v1: https://lore.kernel.org/netdev/3d8387d499f053dba5cd9184c0f7b8445c4470c6.1633542093.git.cdleonard@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that applications binding listening sockets to VRFs without
specifying TCP_MD5SIG_FLAG_IFINDEX will work as expected. This would
be broken if __tcp_md5_do_lookup always made a strict comparison on
l3index. See this email:
https://lore.kernel.org/netdev/209548b5-27d2-2059-f2e9-2148f5a0291b@gmail.com/
Applications using tcp_l3mdev_accept=1 and a single global socket (not
bound to any interface) also should have a way to specify keys that are
only for the default VRF, this is done by --force-bind-key-ifindex
without otherwise binding to a device.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
These options allow explicit control over the TCP_MD5SIG_FLAG_IFINDEX
flag instead of always setting it based on binding to an interface.
Do this by converting to getopt_long because nettest has too many
single-character flags already and getopt_long is widely used in
selftests.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple VRFs are generally meant to be "separate" but right now md5
keys for the default VRF also affect connections inside VRFs if the IP
addresses happen to overlap.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF".
This is what applications using VRFs for traffic separation want.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With net.ipv4.tcp_l3mdev_accept=1 it is possible for a listen socket to
accept connection from the same client address in different VRFs. It is
also possible to set different MD5 keys for these clients which differ
only in the tcpm_l3index field.
This appears to work when distinguishing between different VRFs but not
between non-VRF and VRF connections. In particular:
* tcp_md5_do_lookup_exact will match a non-vrf key against a vrf key.
This means that adding a key with l3index != 0 after a key with l3index
== 0 will cause the earlier key to be deleted. Both keys can be present
if the non-vrf key is added later.
* _tcp_md5_do_lookup can match a non-vrf key before a vrf key. This
casues failures if the passwords differ.
Fix this by making tcp_md5_do_lookup_exact perform an actual exact
comparison on l3index and by making __tcp_md5_do_lookup perfer
vrf-bound keys above other considerations like prefixlen.
Fixes: dea53bb80e07 ("tcp: Add l3index to tcp_md5sig_key and md5 functions")
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6c30 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some new modem device ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYWl3+AAKCRALxc3C7H1l
COsvAP93359O56SZZXvu2SoaIlKB0W4B63n82q2rYLyeiST/TQD/VIDRVIKN05Mk
TdvyrRA6iVa7bEoHxk+YKpa10F7asAA=
=1nE0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.15-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add EM9191 QDL support
USB: serial: option: add Quectel EC200S-CN module support
USB: serial: option: add prod. id for Quectel EG91
USB: serial: option: add Telit LE910Cx composition 0x1204
transport encap_port update should be updated when sctp_vtag_verify()
succeeds, namely, returns 1, not returns 0. Correct it in this patch.
While at it, also fix the indentation.
Fixes: a1dd2cf2f1ae ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a86ed2cfa13c5 ("ptp: Don't print an error if ptp_kvm is not supported")
fixes the error message print on ARM platform by only concerning about
the case that the error returned from kvm_arch_ptp_init() is not -EOPNOTSUPP.
Although the ARM platform returns -EOPNOTSUPP if ptp_kvm is not supported
while X86_64 platform returns -KVM_EOPNOTSUPP, both error codes share the
same value 95.
Actually kvm_arch_ptp_init() on X86_64 platform can return three kinds of
errors (-KVM_ENOSYS, -KVM_EOPNOTSUPP and -KVM_EFAULT). The problem is that
-KVM_EOPNOTSUPP is masked out and -KVM_EFAULT is ignored among them.
This patch fixes this by returning them to ptp_kvm_init() respectively.
Signed-off-by: Kele Huang <huangkele@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added SPI device ID table does not work because the
entry is incorrectly copied from the OF device table.
During build testing, this shows as a compile failure when building
it as a loadable module:
drivers/misc/eeprom/eeprom_93xx46.c:424:1: error: redefinition of '__mod_of__eeprom_93xx46_of_table_device_table'
MODULE_DEVICE_TABLE(of, eeprom_93xx46_of_table);
Change the entry to refer to the correct symbol.
Fixes: 137879f7ff23 ("eeprom: 93xx46: Add SPI device ID table")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014153730.3821376-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Properly refcount pages used as a concatenated stage-2 PGD
- Fix missing unlock when detecting the use of MTE+VM_SHARED
-----BEGIN PGP SIGNATURE-----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=eQRY
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.15, take #2
- Properly refcount pages used as a concatenated stage-2 PGD
- Fix missing unlock when detecting the use of MTE+VM_SHARED
The size of the data in the scratch buffer is not divided by the size of
each port I/O operation, so vcpu->arch.pio.count ends up being larger
than it should be by a factor of size.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
