IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit f58c252e30cf74f68b0054293adc03b5923b9f0e ]
When 8250 UART is using DMA, x_char (XON/XOFF) is never sent
to the wire. After this change, x_char is injected correctly.
Create uart_xchar_out() helper for sending the x_char out and
accounting related to it. It seems that almost every driver
does these same steps with x_char. Except for 8250, however,
almost all currently lack .serial_out so they cannot immediately
take advantage of this new helper.
The downside of this patch is that it might reintroduce
the problems some devices faced with mixed DMA/non-DMA transfer
which caused revert f967fc8f165f (Revert "serial: 8250_dma:
don't bother DMA with small transfers"). However, the impact
should be limited to cases with XON/XOFF (that didn't work
with DMA capable devices to begin with so this problem is not
very likely to cause a major issue, if any at all).
Fixes: 9ee4b83e51f74 ("serial: 8250: Add support for dmaengine")
Reported-by: Gilles Buloz <gilles.buloz@kontron.com>
Tested-by: Gilles Buloz <gilles.buloz@kontron.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220314091432.4288-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab818c7aa7544bf8d2dd4bdf68878b17a02eb332 ]
__setup() handlers should return 1 to obsolete_checksetup() in
init/main.c to indicate that the boot option has been handled.
A return of 0 causes the boot option/value to be listed as an Unknown
kernel parameter and added to init's (limited) environment strings.
So return 1 from kgdboc_option_setup().
Unknown kernel command line parameters "BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd kgdbts=", will be passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc7
kgdboc=kbd
kgdbts=
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Fixes: 1bd54d851f50 ("kgdboc: Passing ekgdboc to command line causes panic")
Fixes: f2d937f3bf00 ("consoles: polling support, kgdboc")
Cc: He Zhe <zhe.he@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: linux-serial@vger.kernel.org
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220309033018.17936-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53819a0d97aace1425bb042829e3446952a9e8a9 ]
__setup() handlers should return 1 to indicate that the boot option
has been handled or 0 to indicate that it was not handled.
Add a pr_warn() message if the option value is invalid and then
always return 1.
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Fixes: 86b40567b917 ("tty: replace strict_strtoul() with kstrtoul()")
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220308024228.20477-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dedab69fd650ea74710b2e626e63fd35584ef773 ]
Set em485->active_timer = NULL isn't always enough to take out the stop
timer. While there is a check that it acts in the right state (i.e.
waiting for RTS-after-send to pass after sending some chars) but the
following might happen:
- CPU1: some chars send, shifter becomes empty, stop tx timer armed
- CPU0: more chars send before RTS-after-send expired
- CPU0: shifter empty irq, port lock taken
- CPU1: tx timer triggers, waits for port lock
- CPU0: em485->active_timer = &em485->stop_tx_timer, hrtimer_start(),
releases lock()
- CPU1: get lock, see em485->active_timer == &em485->stop_tx_timer,
tear down RTS too early
This fix bases on research done by Steffen Trumtrar.
Fixes: b86f86e8e7c5 ("serial: 8250: fix potential deadlock in rs485-mode")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220215160236.344236-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5318f70da7e82649d794fc27d8a127c22aa3566e ]
The pci_get_slot() increases its reference count, the caller
must decrement the reference count by calling pci_dev_put().
Fixes: 9a1870ce812e ("serial: 8250: don't use slave_id of dma_slave_config")
Depends-on: a13e19cf3dc1 ("serial: 8250_lpss: split LPSS driver to separate module")
Reported-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220223151240.70248-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a603ca60cebff8589882427a67f870ed946b3fc8 ]
Commit 54da3e381c2b ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to
set up register mapping") fixed a bug that had, as a side-effect,
prevented the 8250_aspeed_vuart driver from enabling the VUART's
FIFOs. However, fixing that (and hence enabling the FIFOs) has in
turn revealed what appears to be a hardware bug in the ASPEED VUART in
which the host-side THRE bit doesn't get if the BMC-side receive FIFO
trigger level is set to anything but one byte. This causes problems
for polled-mode writes from the host -- for example, Linux kernel
console writes proceed at a glacial pace (less than 100 bytes per
second) because the write path waits for a 10ms timeout to expire
after every character instead of being able to continue on to the next
character upon seeing THRE asserted. (GRUB behaves similarly.)
As a workaround, introduce a new port type for the ASPEED VUART that's
identical to PORT_16550A as it had previously been using, but with
UART_FCR_R_TRIG_00 instead to set the receive FIFO trigger level to
one byte, which (experimentally) seems to avoid the problematic THRE
behavior.
Fixes: 54da3e381c2b ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Tested-by: Konstantin Aladyshev <aladyshev22@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20220211004203.14915-1-zev@bewilderbeest.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd3a4907ee334b40d7aa880c7ab310b154fd5cd4 ]
When LSR is 0xff in ->activate() (rather unlike), we return an error.
Provided ->shutdown() is not called when ->activate() fails, nothing
actually frees the buffer in this case.
Fix this by properly freeing the buffer in a designated label. We jump
there also from the "!info->type" if now too.
Fixes: 6769140d3047 ("tty: mxser: use the tty_port_open method")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220124071430.14907-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3d079bde07e1b7deaeb57506dc0b86010121d17 ]
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a2ab75b8e76e455af7867e3835fd9cdf386b508f upstream.
In the current implementation the user may open a virtual tty which then
could fail to establish the underlying DLCI. The function gsmtty_open()
gets stuck in tty_port_block_til_ready() while waiting for a carrier rise.
This happens if the remote side fails to acknowledge the link establishment
request in time or completely. At some point gsm_dlci_close() is called
to abort the link establishment attempt. The function tries to inform the
associated virtual tty by performing a hangup. But the blocking loop within
tty_port_block_til_ready() is not informed about this event.
The patch proposed here fixes this by resetting the initialization state of
the virtual tty to ensure the loop exits and triggering it to make
tty_port_block_til_ready() return.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 687f9ad43c52501f46164758e908a5dd181a87fc upstream.
The function gsm_process_modem() exists to handle modem status bits of
incoming frames. This includes incoming MSC (modem status command) frames
and convergence layer type 2 data frames. The function, however, was only
designed to handle MSC frames as it expects the command length. Within
gsm_dlci_data() it is wrongly assumed that this is the same as the data
frame length. This is only true if the data frame contains only 1 byte of
payload.
This patch names the length parameter of gsm_process_modem() in a generic
manner to reflect its association. It also corrects all calls to the
function to handle the variable number of modem status octets correctly in
both cases.
Fixes: 7263287af93d ("tty: n_gsm: Fixed logic to decode break signal from modem status")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c19d93542a6081577e6da9bf5e887979c72e80c1 upstream.
tty flow control is handled via gsmtty_throttle() and gsmtty_unthrottle().
Both functions propagate the outgoing hardware flow control state to the
remote side via MSC (modem status command) frames. The local state is taken
from the RTS (ready to send) flag of the tty. However, RTS gets mapped to
DTR (data terminal ready), which is wrong.
This patch corrects this by mapping RTS to RTS.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96b169f05cdcc844b400695184d77e42071d14f2 upstream.
The here fixed commit made the tty hangup asynchronous to avoid a circular
locking warning. I could not reproduce this warning. Furthermore, due to
the asynchronous hangup the function call now gets queued up while the
underlying tty is being freed. Depending on the timing this results in a
NULL pointer access in the global work queue scheduler. To be precise in
process_one_work(). Therefore, the previous commit made the issue worse
which it tried to fix.
This patch fixes this by falling back to the old behavior which uses a
blocking tty hangup call before freeing up the associated tty.
Fixes: 7030082a7415 ("tty: n_gsm: avoid recursive locking with async port hangup")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3b7468f082d106459e86e8dc6fb9bdd65553433 upstream.
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 737b0ef3be6b319d6c1fd64193d1603311969326 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220218073123.2121-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eebb0f4e894f1e9577a56b337693d1051dd6ebfd upstream.
UART drivers are meant to use the port spinlock within certain
methods, to protect against reentrancy. The sc16is7xx driver does
very little locking, presumably because when added it triggers
"scheduling while atomic" errors. This is due to the use of mutexes
within the regmap abstraction layer, and the mutex implementation's
habit of sleeping the current thread while waiting for access.
Unfortunately this lack of interlocking can lead to corruption of
outbound data, which occurs when the buffer used for I2C transmission
is used simultaneously by two threads - a work queue thread running
sc16is7xx_tx_proc, and an IRQ thread in sc16is7xx_port_irq, both
of which can call sc16is7xx_handle_tx.
An earlier patch added efr_lock, a mutex that controls access to the
EFR register. This mutex is already claimed in the IRQ handler, and
all that is required is to claim the same mutex in sc16is7xx_tx_proc.
See: https://github.com/raspberrypi/linux/issues/4885
Fixes: 6393ff1c4435 ("sc16is7xx: Use threaded IRQ")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20220216160802.1026013-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3593030761630e09200072a4bd06468892c27be3 upstream.
Daniel Gibson reports that the n_tty code gets line termination wrong in
very specific cases:
"If you feed a line with exactly 64 chars + terminating newline, and
directly afterwards (without reading) another line into a pseudo
terminal, the the first read() on the other side will return the 64
char line *without* terminating newline, and the next read() will
return the missing terminating newline AND the complete next line (if
it fits in the buffer)"
and bisected the behavior to commit 3b830a9c34d5 ("tty: convert
tty_ldisc_ops 'read()' function to take a kernel pointer").
Now, digging deeper, it turns out that the behavior isn't exactly new:
what changed in commit 3b830a9c34d5 was that the tty line discipline
.read() function is now passed an intermediate kernel buffer rather than
the final user space buffer.
And that intermediate kernel buffer is 64 bytes in size - thus that
special case with exactly 64 bytes plus terminating newline.
The same problem did exist before, but historically the boundary was not
the 64-byte chunk, but the user-supplied buffer size, which is obviously
generally bigger (and potentially bigger than N_TTY_BUF_SIZE, which
would hide the issue entirely).
The reason is that the n_tty canon_copy_from_read_buf() code would look
ahead for the EOL character one byte further than it would actually
copy. It would then decide that it had found the terminator, and unmark
it as an EOL character - which in turn explains why the next read
wouldn't then be terminated by it.
Now, the reason it did all this in the first place is related to some
historical and pretty obscure EOF behavior, see commit ac8f3bf8832a
("n_tty: Fix poll() after buffer-limited eof push read") and commit
40d5e0905a03 ("n_tty: Fix EOF push handling").
And the reason for the EOL confusion is that we treat EOF as a special
EOL condition, with the EOL character being NUL (aka "__DISABLED_CHAR"
in the kernel sources).
So that EOF look-ahead also affects the normal EOL handling.
This patch just removes the look-ahead that causes problems, because EOL
is much more critical than the historical "EOF in the middle of a line
that coincides with the end of the buffer" handling ever was.
Now, it is possible that we should indeed re-introduce the "look at next
character to see if it's a EOF" behavior, but if so, that should be done
not at the kernel buffer chunk boundary in canon_copy_from_read_buf(),
but at a higher level, when we run out of the user buffer.
In particular, the place to do that would be at the top of
'n_tty_read()', where we check if it's a continuation of a previously
started read, and there is no more buffer space left, we could decide to
just eat the __DISABLED_CHAR at that point.
But that would be a separate patch, because I suspect nobody actually
cares, and I'd like to get a report about it before bothering.
Fixes: 3b830a9c34d5 ("tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer")
Fixes: ac8f3bf8832a ("n_tty: Fix poll() after buffer-limited eof push read")
Fixes: 40d5e0905a03 ("n_tty: Fix EOF push handling")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Reported-and-tested-by: Daniel Gibson <metalcaedes@gmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e8793674bb0d1135ca0e5c9f7e16fecbf815926 upstream.
There is a build error when using a kernel .config file from
'kernel test robot' for a different build problem:
hppa64-linux-ld: drivers/tty/serial/8250/8250_gsc.o: in function `.LC3':
(.data.rel.ro+0x18): undefined reference to `iosapic_serial_irq'
when:
CONFIG_GSC=y
CONFIG_SERIO_GSCPS2=y
CONFIG_SERIAL_8250_GSC=y
CONFIG_PCI is not set
and hence PCI_LBA is not set.
IOSAPIC depends on PCI_LBA, so IOSAPIC is not set/enabled.
Make the use of iosapic_serial_irq() conditional to fix the build error.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-parisc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c816b2e65b0e86b95011418cad334f0524fc33b8 upstream.
The poll man page says POLLRDNORM is equivalent to POLLIN when used as
an event.
$ man poll
<snip>
POLLRDNORM
Equivalent to POLLIN.
However, in n_tty driver, POLLRDNORM does not return until timeout even
if there is terminal input, whereas POLLIN returns.
The following test program works until kernel-3.17, but the test stops
in poll() after commit 57087d515441 ("tty: Fix spurious poll() wakeups").
[Steps to run test program]
$ cc -o test-pollrdnorm test-pollrdnorm.c
$ ./test-pollrdnorm
foo <-- Type in something from the terminal followed by [RET].
The string should be echoed back.
------------------------< test-pollrdnorm.c >------------------------
#include <stdio.h>
#include <errno.h>
#include <poll.h>
#include <unistd.h>
void main(void)
{
int n;
unsigned char buf[8];
struct pollfd fds[1] = {{ 0, POLLRDNORM, 0 }};
n = poll(fds, 1, -1);
if (n < 0)
perror("poll");
n = read(0, buf, 8);
if (n < 0)
perror("read");
if (n > 0)
write(1, buf, n);
}
------------------------------------------------------------------------
The attached patch fixes this problem. Many calls to
wake_up_interruptible_poll() in the kernel source code already specify
"POLLIN | POLLRDNORM".
Fixes: 57087d515441 ("tty: Fix spurious poll() wakeups")
Cc: stable@vger.kernel.org
Signed-off-by: Kosuke Tatsukawa <tatsu-ab1@nec.com>
Link: https://lore.kernel.org/r/TYCPR01MB81901C0F932203D30E452B3EA5209@TYCPR01MB8190.jpnprd01.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28cb138f559f8c1a1395f5564f86b8bbee83631b upstream.
in vt_setactivate an almost identical code path has been patched
with array_index_nospec. In the VT_ACTIVATE path the user input
is from a system call argument instead of a usercopy.
For consistency both code paths should have the same mitigations
applied.
Kasper Acknowledgements: Jakob Koschel, Brian Johannesmeyer, Kaveh
Razavi, Herbert Bos, Cristiano Giuffrida from the VUSec group at VU
Amsterdam.
Co-developed-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220127144406.3589293-2-jakobkoschel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61cc70d9e8ef5b042d4ed87994d20100ec8896d9 upstream.
array_index_nospec ensures that an out-of-bounds value is set to zero
on the transient path. Decreasing the value by one afterwards causes
a transient integer underflow. vsa.console should be decreased first
and then sanitized with array_index_nospec.
Kasper Acknowledgements: Jakob Koschel, Brian Johannesmeyer, Kaveh
Razavi, Herbert Bos, Cristiano Giuffrida from the VUSec group at VU
Amsterdam.
Co-developed-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Signed-off-by: Brian Johannesmeyer <bjohannesmeyer@gmail.com>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220127144406.3589293-1-jakobkoschel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 152d1afa834c84530828ee031cf07a00e0fc0b8c upstream.
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8838b2af23caf1ff0610caef2795d6668a013b2d upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d06b1cf28297e27127d3da54753a3a01a2fa2f28 upstream.
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3b3404df318504ec084213ab1065b73f49b0f1d upstream.
Commit a6845e1e1b78 ("serial: core: Consider rs485 settings to drive
RTS") sought to deassert RTS when opening an rs485-enabled uart port.
That way, the transceiver does not occupy the bus until it transmits
data.
Unfortunately, the commit mixed up the logic and *asserted* RTS instead
of *deasserting* it:
The commit amended uart_port_dtr_rts(), which raises DTR and RTS when
opening an rs232 port. "Raising" actually means lowering the signal
that's coming out of the uart, because an rs232 transceiver not only
changes a signal's voltage level, it also *inverts* the signal. See
the simplified schematic in the MAX232 datasheet for an example:
https://www.ti.com/lit/ds/symlink/max232.pdf
So, to raise RTS on an rs232 port, TIOCM_RTS is *set* in port->mctrl
and that results in the signal being driven low.
In contrast to rs232, the signal level for rs485 Transmit Enable is the
identity, not the inversion: If the transceiver expects a "high" RTS
signal for Transmit Enable, the signal coming out of the uart must also
be high, so TIOCM_RTS must be *cleared* in port->mctrl.
The commit did the exact opposite, but it's easy to see why given the
confusing semantics of rs232 and rs485. Fix it.
Fixes: a6845e1e1b78 ("serial: core: Consider rs485 settings to drive RTS")
Cc: stable@vger.kernel.org # v4.14+
Cc: Rafael Gago Castano <rgc@hms.se>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9395767847833f2f3193c49cde38501eeb3b5669.1639821059.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93a770b7e16772530196674ffc79bb13fa927dc6 ]
struct uart_port contains a cached copy of the Modem Control signals.
It is used to skip register writes in uart_update_mctrl() if the new
signal state equals the old signal state. It also avoids a register
read to obtain the current state of output signals.
When a uart_port is registered, uart_configure_port() changes signal
state but neglects to keep the cached copy in sync. That may cause
a subsequent register write to be incorrectly skipped. Fix it before
it trips somebody up.
This behavior has been present ever since the serial core was introduced
in 2002:
https://git.kernel.org/history/history/c/33c0d1b0c3eb
So far it was never an issue because the cached copy is initialized to 0
by kzalloc() and when uart_configure_port() is executed, at most DTR has
been set by uart_set_options() or sunsu_console_setup(). Therefore,
a stable designation seems unnecessary.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/bceeaba030b028ed810272d55d5fc6f3656ddddb.1641129752.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e368cc656fd6d0075f1c3ab9676e2001451e3e04 ]
pl011_set_termios() briefly resets the CR register to zero, thereby
glitching DTR/RTS signals. With rs485 this may result in the bus being
occupied for no reason.
Where does this register write originate from?
The PL011 driver was forked from the PL010 driver in 2004:
https://git.kernel.org/history/history/c/157c0342e591
Until this commit, the PL010 driver's IRQ handler ambauart_int()
modified the CR register without holding the port spinlock.
ambauart_set_termios() also modified that register. To prevent
concurrent read-modify-writes by the IRQ handler and to prevent
transmission while changing baudrate, ambauart_set_termios() had to
disable interrupts. On the PL010, that is achieved by writing zero to
the CR register.
However, on the PL011, interrupts are disabled in the IMSC register,
not in the CR register.
Additionally, the commit amended both the PL010 and PL011 driver to
acquire the port spinlock in the IRQ handler, obviating the need to
disable interrupts in ->set_termios().
So the CR register write is obsolete for two reasons. Drop it.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/f49f945375f5ccb979893c49f1129f51651ac738.1641129062.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08a0c6dff91c965e39905cf200d22db989203ccb ]
pl010_set_termios() briefly resets the CR register to zero.
Where does this register write come from?
The PL010 driver's IRQ handler ambauart_int() originally modified the CR
register without holding the port spinlock. ambauart_set_termios() also
modified that register. To prevent concurrent read-modify-writes by the
IRQ handler and to prevent transmission while changing baudrate,
ambauart_set_termios() had to disable interrupts. That is achieved by
writing zero to the CR register.
However in 2004 the PL010 driver was amended to acquire the port
spinlock in the IRQ handler, obviating the need to disable interrupts in
->set_termios():
https://git.kernel.org/history/history/c/157c0342e591
That rendered the CR register write obsolete. Drop it.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/fcaff16e5b1abb4cc3da5a2879ac13f278b99ed0.1641128728.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 028e083832b06fdeeb290e1e57dc1f6702c4c215 ]
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 274ab58dc2b460cc474ffc7ccfcede4b2be1a3f5 ]
The others are superfluous with tty refcounting in place now. And they
are racy in fact:
* tty_port_initialized() reports false for a small moment after
interrupts are enabled.
* closing is 1 while the port is still alive.
The queues are flushed later during close anyway. So there is no need
for this special handling. Actually, the ISR should not flush the
queues. It should behave as every other driver, just queue the chars
into tty buffer and go on. But this will be changed later. There is
still a lot code depending on having tty in ISR (and not only tty_port).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20211118073125.12283-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 56a23f9319e86e1d62a109896e2c7e52c414e67d ]
Terminate DMA transaction and clear CR3_DMAT when shutdown is requested,
instead of when remove is requested. If DMA transfer is not stopped in
shutdown ops, driver will fail to start a new DMA transfer after next
startup ops.
Fixes: 3489187204eb ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220104182445.4195-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c195438f1e84de8fa46b4f5264d12379bee6e9a1 ]
In case of failures brcmuart_probe() always returned -ENODEV, this
isn't correct for example platform_get_irq_byname() may return
-EPROBE_DEFER to handle such cases propagate error codes in
brcmuart_probe() in case of failures.
Fixes: 41a469482de25 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211224142917.6966-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1180405c7b5c7a1c6bde79d5fc24fe931430737 ]
With commit 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()") the
function devm_ioremap() called from pl011_setup_port() was replaced with
devm_ioremap_resource(). Since this function not only remaps but also
requests the ports io memory region it now collides with the .config_port()
callback which requests the same region at uart port registration.
Since devm_ioremap_resource() already claims the memory successfully, the
request in .config_port() fails.
Later at uart port deregistration the attempt to release the unclaimed
memory also fails. The failure results in a “Trying to free nonexistent
resource" warning.
Fix these issues by removing the callbacks that implement the redundant
memory allocation/release. Also make sure that changing the drivers io
memory base address via TIOCSSERIAL is not allowed any more.
Fixes: 3873e2d7f63a ("drivers: PL011: refactor pl011_probe()")
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20211129174238.8333-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3672fb65155530b5eea6225685c75329b6debec3 ]
The base address of uartlite registers could be 64 bit address which is from
device resource. When ulite_probe() calls ulite_assign(), this 64 bit
address is casted to 32-bit. The fix is to replace "u32" type with
"phys_addr_t" type for the base address in ulite_assign() argument list.
Fixes: 8fa7b6100693 ("[POWERPC] Uartlite: Separate the bus binding from the driver proper")
Signed-off-by: Lizhi Hou <lizhi.hou@xilinx.com>
Link: https://lore.kernel.org/r/20211129202302.1319033-1-lizhi.hou@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f4b9b5895614eb2e2b5f4cab7858f44bd113e1b ]
The driver wrongly assummed that tx_submit() will start the transfer,
which is not the case, now that the at_xdmac driver is fixed. tx_submit
is supposed to push the current transaction descriptor to a pending queue,
waiting for issue_pending to be called. issue_pending must start the
transfer, not tx_submit.
Fixes: 34df42f59a60 ("serial: at91: add rx dma support")
Fixes: 08f738be88bb ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211125090028.786832-4-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e67bd2b8cb90b66e89562598e9c2046246832d3 ]
The tx_submit() method of struct dma_async_tx_descriptor is entitled
to do sanity checks and return errors if encountered. It's not the
case for the DMA controller drivers that this client is using
(at_h/xdmac), because they currently don't do sanity checks and always
return a positive cookie at tx_submit() method. In case the controller
drivers will implement sanity checks and return errors, print a message
so that the client will be informed that something went wrong at
tx_submit() level.
Fixes: 08f738be88bb ("serial: at91: add tx dma support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20211125090028.786832-3-tudor.ambarus@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fe415186b43df0db1f17fa3a46275fd92107fe71 upstream.
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
This is part of XSA-391
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c33ff728812aa18792afffaf2c9873b898e7512 upstream.
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae5b ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d44f ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c624 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ee33b1ca2b8dabfcc17198ffd049a6b55674a86 upstream.
syzbot is reporting that an unprivileged user who logged in from tty
console can crash the system using a reproducer shown below [1], for
n_hdlc_tty_wakeup() is synchronously calling n_hdlc_send_frames().
----------
#include <sys/ioctl.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
const int disc = 0xd;
ioctl(1, TIOCSETD, &disc);
while (1) {
ioctl(1, TCXONC, 0);
write(1, "", 1);
ioctl(1, TCXONC, 1); /* Kernel panic - not syncing: scheduling while atomic */
}
}
----------
Linus suspected that "struct tty_ldisc"->ops->write_wakeup() must not
sleep, and Jiri confirmed it from include/linux/tty_ldisc.h. Thus, defer
n_hdlc_send_frames() from n_hdlc_tty_wakeup() to a WQ context like
net/nfc/nci/uart.c does.
Link: https://syzkaller.appspot.com/bug?extid=5f47a8cea6a12b77a876 [1]
Reported-by: syzbot <syzbot+5f47a8cea6a12b77a876@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Analyzed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Confirmed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/40de8b7e-a3be-4486-4e33-1b1d1da452f8@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e9679738a918d8a482ac6a2cb2bb871f094bb84 ]
Revert commit b4b844930f27 ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 05f929b395dec8957b636ff14e66b277ed022ed9 upstream.
Deregister the port when unbinding the driver to prevent it from being
used after releasing the driver data and leaking memory allocated by
serial core.
Fixes: 1da81e5562fa ("drivers/tty/serial: add LiteUART driver")
Cc: stable@vger.kernel.org # 5.11
Cc: Filip Kokosinski <fkokosinski@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211117100512.5058-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f85e04503f369b3f2be28c83fc48b74e19936ebc upstream.
Commit f45709df7731 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
do_sys_openat2
do_filp_open
path_openat
vfs_open
do_dentry_open
chrdev_open
tty_open
uart_open
tty_port_open
uart_port_activate
uart_startup
uart_port_startup
serial8250_startup
omap_8250_startup # up->mcr = 0
uart_change_speed
serial8250_set_termios
omap_8250_set_termios
omap_8250_restore_regs
serial8250_out_MCR # up->mcr written
tty_port_block_til_ready
uart_dtr_rts
uart_port_dtr_rts
serial8250_set_mctrl
omap8250_set_mctrl
serial8250_do_set_mctrl # mcr[1] = 1 ignored
Fix by intercepting RTS changes from user space in uart_tiocmset()
instead.
Link: https://lore.kernel.org/linux-serial/20211027111644.1996921-1-baocheng.su@siemens.com/
Fixes: f45709df7731 ("serial: 8250: Don't touch RTS modem control while in rs485 mode")
Cc: Chao Zeng <chao.zeng@siemens.com>
Cc: stable@vger.kernel.org # v5.7+
Reported-by: Su Bao Cheng <baocheng.su@siemens.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/21170e622a1aaf842a50b32146008b5374b3dd1d.1637596432.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb1201d4b38ec67bd9a871cf86b0cc10f28b15b5 upstream.
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c525c5d2437f93520388920baac6d9340c65d239 upstream.
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9bd3 ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jay Dolan <jay.dolan@accesio.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00de977f9e0aa9760d9a79d1e41ff780f74e3424 upstream.
Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e46e ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145ace ("tty/serial: do not free
trasnmit buffer page under port lock")).
Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il
Fixes: 761ed4a94582 ("tty: serial_core: convert uart_close to use tty_port_close")
Cc: stable@vger.kernel.org # 4.9
Cc: Rob Herring <robh@kernel.org>
Reported-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
