IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 89bcd9a64b849380ef57e3032b307574e48db524 upstream.
MediaTek IP requires that after dma stop, it need to wait this dma stop
bit auto-reset to 0. When bus is in high loading state, it will take a
while for the dma stop complete. If there is no waiting operation here,
when program runs to clear fifo and reset, bus will hang.
In addition, there should be no return in msdc_data_xfer_next() if
there is data need be transferred, because no matter what error occurs
here, it should continue to excute to the following mmc_request_done.
Otherwise the core layer may wait complete forever.
Signed-off-by: Mengqi Zhang <mengqi.zhang@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220609112239.18911-1-mengqi.zhang@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a051246b786af7e4a9d9219cc7038a6e8a411531 upstream.
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
Fixes: 1e8e55b67030c6 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220531171922.76080-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23e09be254f95a5b75cd87f91a4014f3b46dda3f upstream.
Occasionally, user-land applications initiate longer timeout values for certain commands
through ioctl() system call. But so far we are still using a fixed timeout of 10 seconds
in mmc_poll_for_busy() on the ioctl() path, even if a custom timeout is specified in the
userspace application. This patch allows custom timeout values to override this default
timeout values on the ioctl path.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220423221623.1074556-3-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c7666240ec76422cb7546bd07cc8ae80dc0ccdd2 ]
The ARASAN MMC controller on Keystone 3 class of devices need the SDCD
line to be connected for proper functioning. Similar to the issue pointed
out in sdhci-of-arasan.c driver, commit 3794c542641f ("mmc:
sdhci-of-arasan: Set controller to test mode when no CD bit").
In cases where this can't be connected, add a quirk to force the
controller into test mode and set the TESTCD bit. Use the flag
"ti,fails-without-test-cd", to implement this above quirk when required.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220425063120.10135-3-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1f311c94aabdb419c28e3147bcc8ab89269f1a7e upstream.
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/1badf10aba764191a1a752edcbf90389@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Christian Löhle <CLoehle@hyperstone.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4bc31edebde51fcf8ad0794763b8679a7ecb5ec0 upstream.
Way back in commit 4f25580fb84d ("mmc: core: changes frequency to
hs_max_dtr when selecting hs400es"), Rockchip engineers noticed that
some eMMC don't respond to SEND_STATUS commands very reliably if they're
still running at a low initial frequency. As mentioned in that commit,
JESD84-B51 P49 suggests a sequence in which the host:
1. sets HS_TIMING
2. bumps the clock ("<= 52 MHz")
3. sends further commands
It doesn't exactly require that we don't use a lower-than-52MHz
frequency, but in practice, these eMMC don't like it.
The aforementioned commit tried to get that right for HS400ES, although
it's unclear whether this ever truly worked as committed into mainline,
as other changes/refactoring adjusted the sequence in conflicting ways:
08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode
switch")
53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode
for mmc")
In any case, today we do step 3 before step 2. Let's fix that, and also
apply the same logic to HS200/400, where this eMMC has problems too.
Resolves errors like this seen when booting some RK3399 Gru/Scarlet
systems:
[ 2.058881] mmc1: CQHCI version 5.10
[ 2.097545] mmc1: SDHCI controller on fe330000.mmc [fe330000.mmc] using ADMA
[ 2.209804] mmc1: mmc_select_hs400es failed, error -84
[ 2.215597] mmc1: error -84 whilst initialising MMC card
[ 2.417514] mmc1: mmc_select_hs400es failed, error -110
[ 2.423373] mmc1: error -110 whilst initialising MMC card
[ 2.605052] mmc1: mmc_select_hs400es failed, error -110
[ 2.617944] mmc1: error -110 whilst initialising MMC card
[ 2.835884] mmc1: mmc_select_hs400es failed, error -110
[ 2.841751] mmc1: error -110 whilst initialising MMC card
Ealier versions of this patch bumped to 200MHz/HS200 speeds too early,
which caused issues on, e.g., qcom-msm8974-fairphone-fp2. (Thanks for
the report Luca!) After a second look, it appears that aligns with
JESD84 / page 45 / table 28, so we need to keep to lower (HS / 52 MHz)
rates first.
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed mode switch")
Fixes: 53e60650f74e ("mmc: core: Allow CMD13 polling when switching to HS mode for mmc")
Fixes: 4f25580fb84d ("mmc: core: changes frequency to hs_max_dtr when selecting hs400es")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/linux-mmc/11962455.O9o76ZdvQC@g550jk/
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220422100824.v4.1.I484f4ee35609f78b932bd50feed639c29e64997e@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9f3fb523dbf476dc86beea23f5b5ca8f9687c93 upstream.
Newer variants of the MMC controller support a 34-bit physical address
space by using word addresses instead of byte addresses. However, the
code truncates the DMA descriptor address to 32 bits before applying the
shift. This breaks DMA for descriptors allocated above the 32-bit limit.
Fixes: 3536b82e5853 ("mmc: sunxi: add support for A100 mmc controller")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220424231751.32053-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08ebf903af57cda6d773f3dd1671b64f73b432b8 upstream.
During the card initialization process, the mmc core checks whether the
eMMC/SD card supports an internal writeback-cache and then enables it
inside the card.
Unfortunately, this isn't according to what the mmc core reports to the
upper block layer. Instead, the writeback-cache support with REQ_FLUSH and
REQ_FUA, are being enabled depending on whether the host supports the CMD23
(MMC_CAP_CMD23) and whether an eMMC supports the reliable-write command.
This is wrong and it may also sound awkward. In fact, it's a remnant
from when both eMMC/SD cards didn't have dedicated commands/support to
control the internal writeback-cache. In other words, it was the best we
could do at that point in time.
To fix the problem, but also without breaking backwards compatibility,
let's align the REQ_FLUSH support with whether the writeback-cache became
successfully enabled - for both eMMC and SD cards.
Cc: stable@kernel.org
Fixes: 881d1c25f765 ("mmc: core: Add cache control for eMMC4.5 device")
Fixes: 130206a615a9 ("mmc: core: Add support for cache ctrl for SD cards")
Depends-on: 97fce126e279 ("mmc: block: Issue a cache flush only when it's enabled")
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Michael Wu <michael@allwinnertech.com>
Link: https://lore.kernel.org/r/20220331073223.106415-1-michael@allwinnertech.com
[Ulf: Re-wrote the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 03e59b1e2f56245163b14c69e0a830c24b1a3a47 upstream.
When HS400 tuning is complete and HS400 is going to be activated, we
have to keep the current number of TAPs and should not overwrite them
with a hardcoded value. This was probably a copy&paste mistake when
upporting HS400 support from the BSP.
Fixes: 26eb2607fa28 ("mmc: renesas_sdhi: add eMMC HS400 mode support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220404114902.12175-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0d319dd5a27183b75d984e3dc495248e59f99334 upstream.
Use sg and not data->sg when checking sg list elements. Else only the
first element alignment is checked.
The last element should be checked the same way, for_each_sg already set
sg to sg_next(sg).
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220317111944.116148-2-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d435933376962b107bd76970912e7e80247dcc7 upstream.
Introduce a SEND_STATUS check for writes through SPI to not mark
an unsuccessful write as successful.
Since SPI SD/MMC does not have states, after a write, the card will
just hold the line LOW until it is ready again. The driver marks the
write therefore as completed as soon as it reads something other than
all zeroes.
The driver does not distinguish from a card no longer signalling busy
and it being disconnected (and the line being pulled-up by the host).
This lead to writes being marked as successful when disconnecting
a busy card.
Now the card is ensured to be still connected by an additional CMD13,
just like non-SPI is ensured to go back to TRAN state.
While at it and since we already poll for the post-write status anyway,
we might as well check for SPIs error bits (any of them).
The disconnecting card problem is reproducable for me after continuous
write activity and randomly disconnecting, around every 20-50 tries
on SPI DS for some card.
Fixes: 7213d175e3b6f ("MMC/SD card driver learns SPI")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/76f6f5d2b35543bab3dfe438f268609c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3dd9a926ec2308e49445f22abef149fc64e9332e upstream.
The struct device *dev, is no longer needed at various functions, let's
therefore drop it to fix the build errors/warnings.
Fixes: 7570fb41e450 ("mmc: rtsx: Let MMC core handle runtime PM")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220301115300.64332-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7570fb41e450ba37bf9335fe3751fa9f502c30fa upstream.
Since MMC core handles runtime PM reference counting, we can avoid doing
redundant runtime PM work in the driver. That means the only thing
commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM") misses is
to always enable runtime PM, to let its parent driver enable ASPM in the
runtime idle routine.
Fixes: 7499b529d97f ("mmc: rtsx: Use pm_runtime_{get,put}() to handle runtime PM")
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220216055435.2335297-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7499b529d97f752124fa62fefa1d6d44b371215a upstream.
Commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM") doesn't
use pm_runtime_{get,put}() helpers when it should, so the RPM refcount
keeps at zero, hence its parent driver, rtsx_pci, has to do lots of
weird tricks to keep it from runtime suspending.
So use those helpers at right places to properly manage runtime PM.
Fixes: 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM")
Cc: Ricky WU <ricky_wu@realtek.com>
Tested-by: Ricky WU <ricky_wu@realtek.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20220125055010.1866563-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d6c9219ca1139b74541b2a98cee47a3426d754a9 ]
Even if the current WARN() notifies the user that something is severely
wrong, we can still end up in a PANIC() when trying to invoke the missing
->enable_sdio_irq() ops. Therefore, let's also return an error code and
prevent the host from being added.
While at it, move the code into a separate function to prepare for
subsequent changes and for further host caps validations.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20220303165142.129745-1-ulf.hansson@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09e7af76db02c74f2a339b3cb2d95460fa2ddbe4 ]
As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.
Fixes: bbce5802afc5 ("davinci: mmc: updates to suspend/resume implementation")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220308071415.1093393-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b7340f1c89cc488e4df0b033bf7ae502ebbf5b2 ]
The MMCSD IPs used in AM64 are the same as the ones used in J721E.
Therefore, fix this by using the driver data from J721E for AM64 too, for
both 8 and 4 bit instances.
Fixes: 754b7f2f7d2a ("mmc: sdhci_am654: Add Support for TI's AM64 SoC")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20220211075056.26179-1-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f0d2f15362f02444c5d7ffd5a5eb03e4aa54b685 upstream.
Currently meson_mmc_post_req() is called in meson_mmc_request() right
after meson_mmc_start_cmd(). This could lead to DMA unmapping before the request
is actually finished.
To fix, don't call meson_mmc_post_req() until meson_mmc_request_done().
Signed-off-by: Rong Chen <rong.chen@amlogic.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Fixes: 79ed05e329c3 ("mmc: meson-gx: add support for descriptor chain mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220216124239.4007667-1-rong.chen@amlogic.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54309fde1a352ad2674ebba004a79f7d20b9f037 upstream.
On reads with MMC_READ_MULTIPLE_BLOCK that fail,
the recovery handler will use MMC_READ_SINGLE_BLOCK for
each of the blocks, up to MMC_READ_SINGLE_RETRIES times each.
The logic for this is fixed to never report unsuccessful reads
as success to the block layer.
On command error with retries remaining, blk_update_request was
called with whatever value error was set last to.
In case it was last set to BLK_STS_OK (default), the read will be
reported as success, even though there was no data read from the device.
This could happen on a CRC mismatch for the response,
a card rejecting the command (e.g. again due to a CRC mismatch).
In case it was last set to BLK_STS_IOERR, the error is reported correctly,
but no retries will be attempted.
Fixes: 81196976ed946c ("mmc: block: Add blk-mq support")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/bc706a6ab08c4fe2834ba0c05a804672@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 379f56c24e698f14242f532b1d0a0f1747725e08 upstream.
SD card is allowed to signal busy on DAT0 up to 1s after the
CMD49. According to SD spec (version 6.0 section 5.8.1.3) first host
waits until busy of CMD49 is released and only then polls Power
Management Status register up to 1s until the card indicates ready to
power off.
Without waiting for busy before polling status register sometimes card
becomes unresponsive and system fails to suspend:
[ 205.907459] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 206.421274] sunxi-mmc 1c0f000.mmc: data error, sending stop command
[ 206.421321] sunxi-mmc 1c0f000.mmc: send stop command failed
[ 206.421347] mmc0: error -110 reading status reg of PM func
[ 206.421366] PM: dpm_run_callback(): mmc_bus_suspend+0x0/0x74 returns -110
[ 206.421402] mmcblk mmc0:aaaa: PM: failed to suspend async: error -110
[ 206.437064] PM: Some devices failed to suspend, or early wake event detected
Tested with Sandisk Extreme PRO A2 64GB on Allwinner A64 system.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Fixes: 2c5d42769038 ("mmc: core: Add support for Power Off Notification for SD cards")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220115121447.641524-1-andrej.skvortzov@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40c67c291a93f8846c4a972c9ef1b7ba4544c8d0 upstream.
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
And since the sdhci_setup_host() has already checked the return value of
the enable_dma, we need not check it in sdhci_resume_host() again.
Fixes: 5552d7ad596c ("mmc: sdhci-of-esdhc: set proper dma mask for ls104x chips")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220112083156.1124782-1-jiasheng@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd2db32e7c3e35bd4d9b8bbff689434a50893546 upstream.
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Cc: Xin Xiong <xiongx18@fudan.edu.cn>
Cc: Xin Tan <tanxin.ctf@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yang Li <yang.lee@linux.alibaba.com>
Cc: linux-mmc@vger.kernel.org
Cc: stable <stable@vger.kernel.org>
Reported-by: whitehat002 <hackyzh002@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ffaea6ebfe9ce06ebb3a54811a47688f2b0893cd ]
Replace all instances of open-coded while loops for polling registers
with calls to readl_poll_timeout() and, while at it, also fix some
possible infinite loop instances.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20211216125748.179602-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 189f1d9bc3a5ea3e442e119e4a5deda63da8c462 ]
This is required on some Apple ARM64 laptops using this controller.
As is typical on DT platforms, pull these quirks from the device tree
using the standard mmc bindings.
See Documentation/devicetree/bindings/mmc/mmc-controller.yaml
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20211215161045.38843-2-marcan@marcan.st
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c3e5b74b9e2146f564905e50ca716591c76d4f1 ]
The mmc core takes a specific path to support initializing of a
non-standard SDIO card. This is triggered by looking for the card-quirk,
MMC_QUIRK_NONSTD_SDIO.
In mmc_sdio_init_card() this gets rather messy, as it causes the code to
bail out earlier, compared to the usual path. This leads to that the OCR
doesn't get saved properly in card->ocr. Fortunately, only omap_hsmmc has
been using the MMC_QUIRK_NONSTD_SDIO and is dealing with the issue, by
assigning a hardcoded value (0x80) to card->ocr from an ->init_card() ops.
To make the behaviour consistent, let's instead rely on the core to save
the OCR in card->ocr during initialization.
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/e7936cff7fc24d187ef2680d3b4edb0ade58f293.1636564631.git.hns@goldelico.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e315b1f3a170f368da5618f8a598e68880302ed1 ]
Refactor the code so that card detect irqs are always reenabled after a
reset. This avoids doing it manually all over the code or forgetting to
do this in the future.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
[wsa: added a comment when 'native_hotplug' has to be set]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211103122646.64422-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fc9a77bc64e1f23d07953439817d8402ac9706f ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: ed80a13bb4c4 ("mmc: meson-mx-sdio: Add a driver for the Amlogic Meson8 and Meson8b SoC")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211217202717.10041-3-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77bed755e0f06135faccdd3948863703f9a6e640 ]
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: e4bf1b0970ef ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20211217202717.10041-2-s.shtylyov@omp.ru
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ff31ee0a0f471776f67be5e5275c18d17736fc6b upstream.
During test campaign, and especially after several unbind/bind sequences,
it has been seen that the SD-card on SDMMC1 thread could freeze.
The freeze always appear on a CMD23 following a CMD19.
Checking SDMMC internal registers shows that the tuning command (CMD19)
has failed.
The freeze is then due to the delay block involved in the tuning sequence.
To correct this, clear the delay block register DLYB_CR register after
the tuning commands.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 1103f807a3b9 ("mmc: mmci_sdmmc: Add execute tuning with delay block")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211215141727.4901-4-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66c915d09b942fb3b2b0cb2f56562180901fba17 upstream.
It's seems prone to problems by allowing card detect and its corresponding
mmc_rescan() work to run, during platform shutdown. For example, we may end
up turning off the power while initializing a card, which potentially could
damage it.
To avoid this scenario, let's add ->shutdown_pre() callback for the mmc host
class device and then turn of the card detect from there.
Reported-by: Al Cooper <alcooperx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211203141555.105351-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f89b548ca66be7500dcd92ee8e61590f7d08ac91 upstream.
The vendor driver implements special handling for multi-block
SD_IO_RW_EXTENDED (and SD_IO_RW_DIRECT) commands which have data
attached to them. It sets the MANUAL_STOP bit in the MESON_SDHC_MISC
register for these commands. In all other cases this bit is cleared.
Here we omit SD_IO_RW_DIRECT since that command never has any data
attached to it.
This fixes SDIO wifi using the brcmfmac driver which reported the
following error without this change on a Netxeon S82 board using a
Meson8 (S802) SoC:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_sdiod_ramrw: membytes transfer failed
brcmf_sdio_download_code_file: error -110 on writing 219557 membytes
at 0x00000000
brcmf_sdio_download_firmware: dongle image file download failed
And with this change:
brcmf_fw_alloc_request: using brcm/brcmfmac43362-sdio for chip
BCM43362/1
brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may
have limited channels available
brcmf_c_preinit_dcmds: Firmware: BCM43362/1 wl0: Apr 22 2013 14:50:00
version 5.90.195.89.6 FWID 01-b30a427d
Fixes: e4bf1b0970ef96 ("mmc: host: meson-mx-sdhc: new driver for the Amlogic Meson SDHC host")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211219153442.463863-2-martin.blumenstingl@googlemail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fc7261dbab139d3c64c3b618262504e16cfe7ee upstream.
When CMD13 is sent after switching to HS400ES mode, the bus
is operating at either MMC_HIGH_26_MAX_DTR or MMC_HIGH_52_MAX_DTR.
To meet Tegra SDHCI requirement at HS400ES mode, force SDHCI
interface clock to MMC_HS200_MAX_DTR (200 MHz) so that host
controller CAR clock and the interface clock are rate matched.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: dfc9700cef77 ("mmc: tegra: Implement HS400 enhanced strobe")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211214113653.4631-1-pshete@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dba402807a85fa3723f4a27504813caf81cc9d7 upstream.
'cmd_error' is not necessarily initialized on some error paths in
mmc_send_tuning(). Initialize it.
Fixes: 2c9017d0b5d3 ("mmc: renesas_sdhi: abort tuning when timeout detected")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211130132309.18246-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f719948b5d43eb39356e94e8d0b462568915381 upstream.
Commit 5fa6863ba692 ("spi: Check we have a spi_device_id for each DT
compatible") added a test to check that every SPI driver has a
spi_device_id for each DT compatiable string defined by the driver
and warns if the spi_device_id is missing. The spi_device_id is
missing for the MMC SPI driver and the following warning is now seen.
WARNING KERN SPI driver mmc_spi has no spi_device_id for mmc-spi-slot
Fix this by adding the necessary spi_device_id.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20211115113813.238044-1-jonathanh@nvidia.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d7c194b7c9ad414264935ad4f943a6ce285ebb1 upstream.
The block layer forces a minimum segment size of PAGE_SIZE, so a segment
can be too big for the ADMA table, if PAGE_SIZE >= 64KiB. Fix by writing
multiple descriptors, noting that the ADMA table is sized for 4KiB chunks
anyway, so it will be big enough.
Reported-and-tested-by: Bough Chen <haibo.chen@nxp.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211115082345.802238-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0eab756f8821d255016c63bb55804c429ff4bdb1 upstream.
There are several error return paths that dereference the null pointer
host because the pointer has not yet been set to a valid value.
Fix this by adding a new out_mmc label and exiting via this label
to avoid the host clean up and hence the null pointer dereference.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 8105c2abbf36 ("mmc: moxart: Fix reference count leaks in moxart_probe")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211013100052.125461-1-colin.king@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce5f6c2c9b0fcb4094f8e162cfd37fb4294204f7 ]
The 'reg_vmmc' regulator is enabled in the probe. It is never disabled.
Neither in the error handling path of the probe nor in the remove
function.
Register a devm_action to disable it when needed.
Fixes: 4dc5a79f1350 ("mmc: mxs-mmc: enable regulator for mmc slot")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/4aadb3c97835f7b80f00819c3d549e6130384e67.1634365151.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d806e334d0390502cd2a820ad33d65d7f9bba618 ]
We need to restore context in a specified order with HCTL set in two
phases. This is similar to what omap_hsmmc_context_restore() is doing.
Otherwise SDIO can stop working on resume.
And for PM runtime and SDIO cards, we need to also save SYSCTL, IE and
ISE.
This should not be a problem currently, and these patches can be applied
whenever suitable.
Fixes: ee0f309263a6 ("mmc: sdhci-omap: Add Support for Suspend/Resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e0e7bd38b1ec7f9e5d18725ad41828be4e09859 ]
If sdhci-omap is configured for an unused device instance and the device
is not set as disabled, we can get a NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address
00000045
...
(regulator_set_voltage) from [<c07d7008>] (mmc_regulator_set_ocr+0x44/0xd0)
(mmc_regulator_set_ocr) from [<c07e2d80>] (sdhci_set_ios+0xa4/0x490)
(sdhci_set_ios) from [<c07ea690>] (sdhci_omap_set_ios+0x124/0x160)
(sdhci_omap_set_ios) from [<c07c8e94>] (mmc_power_up.part.0+0x3c/0x154)
(mmc_power_up.part.0) from [<c07c9d20>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c07cad34>] (mmc_add_host+0x58/0x7c)
(mmc_add_host) from [<c07e2574>] (__sdhci_add_host+0xf0/0x22c)
(__sdhci_add_host) from [<c07eaf68>] (sdhci_omap_probe+0x318/0x72c)
(sdhci_omap_probe) from [<c06a39d8>] (platform_probe+0x58/0xb8)
AFAIK we are not seeing this with the devices configured in the mainline
kernel but this can cause issues for folks bringing up their boards.
Fixes: 7d326930d352 ("mmc: sdhci-omap: Add OMAP SDHCI driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210921110029.21944-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8105c2abbf36296bf38ca44f55ee45d160db476a ]
The issue happens in several error handling paths on two refcounted
object related to the object "host" (dma_chan_rx, dma_chan_tx). In
these paths, the function forgets to decrement one or both objects'
reference count increased earlier by dma_request_chan(), causing
reference count leaks.
Fix it by balancing the refcounts of both objects in some error
handling paths. In correspondence with the changes in moxart_probe(),
IS_ERR() is replaced with IS_ERR_OR_NULL() in moxart_remove() as well.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Link: https://lore.kernel.org/r/20211009041918.28419-1-xiongx18@fudan.edu.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 43592c8736e84025d7a45e61a46c3fa40536a364 upstream.
Only wait for DRTO on reads, otherwise the driver hangs.
The driver prevents sending CMD12 on response errors like CRCs. According
to the comment this is because some cards have problems with this during
the UHS tuning sequence. Unfortunately this workaround currently also
applies for any command with data. On reads this will set the drto timer,
which then triggers after a while. On writes this will not set any timer
and the tasklet will not be scheduled again.
I cannot test for the UHS workarounds need, but even if so, it should at
most apply to reads. I have observed many hangs when CMD25 response
contained a CRC error. This patch fixes this without touching the actual
UHS tuning workaround.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/af8f8b8674ba4fcc9a781019e4aeb72c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43e5fee317f4b0a48992b8b07935b1a3ac20ce84 upstream.
We found this issue on a 5G platform, during CMDQ error handling, if DMA
status is active when it call msdc_reset_hw(), it means mmc host hw reset
and DMA transfer will be parallel, mmc host may access sram region
unexpectedly. According to the programming guide of mtk-sd host, it needs
to wait for dma stop done after set dma stop.
This change should be applied to all SoCs.
Signed-off-by: Derong Liu <derong.liu@mediatek.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210827071537.1034-1-derong.liu@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset callback may clear the internal card detect interrupts, so
make sure to reenable them if needed.
Fixes: b4d86f37eacb ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211028195149.8003-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We must enable clock before cqhci init, because crypto needs read
information from CQHCI registers, otherwise, it will hang in MediaTek mmc
host controller.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Fixes: 88bd652b3c74 ("mmc: mediatek: command queue support")
Cc: stable@vger.kernel.org
Acked-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20211028022049.22129-1-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
