IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit fa152f626b24ec2ca3489100d8c5c0a0bce4e2ef upstream.
In case of asix_ax88772a_link_change_notify() workaround, we run soft
reset which will automatically clear MII_ADVERTISE configuration. The
PHYlib framework do not know about changed configuration state of the
PHY, so we need use phy_init_hw() to reinit PHY configuration.
Fixes: dde258469257 ("net: usb/phy: asix: add support for ax88772A/C PHYs")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220628114349.3929928-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e597e2affb90d6ea48df6890d882924acf71e19 upstream.
Some RX errors, notably when disconnecting the cable, increase the RCSR
register. Once half full (0x7fff), an interrupt flood is generated. I
measured ~3k/s interrupts even after the RX errors transfer was
stopped.
Since we don't read and clear the RCSR register, we should disable this
interrupt.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c96614eeab663646f57f67aa591e015abd8bd0ba upstream.
When unplugging an Ethernet cable, false carrier events were produced by
the PHY at a very high rate. Once the false carrier counter full, an
interrupt was triggered every few clock cycles until the cable was
replugged. This resulted in approximately 10k/s interrupts.
Since the false carrier counter (FCSCR) is never used, we can safely
disable this interrupt.
In addition to improving performance, this also solved MDIO read
timeouts I was randomly encountering with an i.MX8 fec MAC because of
the interrupt flood. The interrupt count and MDIO timeout fix were
tested on a v5.4.110 kernel.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1758bde2e4aa5ff188d53e7d9d388bbb7e12eebb upstream.
Upon system sleep, mdio_bus_phy_suspend() stops the phy_state_machine(),
but subsequent interrupts may retrigger it:
They may have been left enabled to facilitate wakeup and are not
quiesced until the ->suspend_noirq() phase. Unwanted interrupts may
hence occur between mdio_bus_phy_suspend() and dpm_suspend_noirq(),
as well as between dpm_resume_noirq() and mdio_bus_phy_resume().
Retriggering the phy_state_machine() through an interrupt is not only
undesirable for the reason given in mdio_bus_phy_suspend() (freezing it
midway with phydev->lock held), but also because the PHY may be
inaccessible after it's suspended: Accesses to USB-attached PHYs are
blocked once usb_suspend_both() clears the can_submit flag and PHYs on
PCI network cards may become inaccessible upon suspend as well.
Amend phy_interrupt() to avoid triggering the state machine if the PHY
is suspended. Signal wakeup instead if the attached net_device or its
parent has been configured as a wakeup source. (Those conditions are
identical to mdio_bus_phy_may_suspend().) Postpone handling of the
interrupt until the PHY has resumed.
Before stopping the phy_state_machine() in mdio_bus_phy_suspend(),
wait for a concurrent phy_interrupt() to run to completion. That is
necessary because phy_interrupt() may have checked the PHY's suspend
status before the system sleep transition commenced and it may thus
retrigger the state machine after it was stopped.
Likewise, after re-enabling interrupt handling in mdio_bus_phy_resume(),
wait for a concurrent phy_interrupt() to complete to ensure that
interrupts which it postponed are properly rerun.
The issue was exposed by commit 1ce8b37241ed ("usbnet: smsc95xx: Forward
PHY interrupts to PHY driver to avoid polling"), but has existed since
forever.
Fixes: 541cd3ee00a4 ("phylib: Fix deadlock on resume")
Link: https://lore.kernel.org/netdev/a5315a8a-32c2-962f-f696-de9a26d30091@samsung.com/
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v2.6.33+
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/b7f386d04e9b5b0e2738f0125743e30676f309ef.1656410895.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b7fd1670a94a57d974795acebde843a5c1a354e ]
Even when the eth port is resticted to work with speeds not higher than 1G,
and so the eth driver is requesting the phy (via phylink) to advertise up
to 1000BASET support, the aquantia phy device is still advertising for 2.5G
and 5G speeds.
Clear these advertising defaults when requested.
Cc: Ondrej Spacek <ondrej.spacek@nxp.com>
Fixes: 09c4c57f7bc41 ("net: phy: aquantia: add support for auto-negotiation configuration")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20220610084037.7625-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c76acfb7e19dcc3a0964e0563770b1d11b8d4540 upstream.
There is a limitation in TI DP83867 PHY device where SGMII AN is only
triggered once after the device is booted up. Even after the PHY TPI is
down and up again, SGMII AN is not triggered and hence no new in-band
message from PHY to MAC side SGMII.
This could cause an issue during power up, when PHY is up prior to MAC.
At this condition, once MAC side SGMII is up, MAC side SGMII wouldn`t
receive new in-band message from TI PHY with correct link status, speed
and duplex info.
As suggested by TI, implemented a SW solution here to retrigger SGMII
Auto-Neg whenever there is a link change.
v2: Add Fixes tag in commit message.
Fixes: 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220526090347.128742-1-tee.min.tan@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 35b42dce619701f1300fb8498dae82c9bb1f0263 ]
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
drivers/net/phy/phy_device.c is never compiled as modular.
(CONFIG_PHYLIB is boolean)
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2ef6f7539c68c6bd6c32323d8845ee102b7c450 ]
Currently, if the .probe element is present in the phy_driver structure
and the .driver_data is not, a NULL pointer dereference happens.
Allow passing .probe without .driver_data by inserting NULL checks
for priv->type.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220513114613.762810-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 15f03ffe4bb951e982457f44b6cf6b06ef4cbb93 upstream.
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the kszphy_suspend/
resume hooks are used.
These functions require the probe function to be called so that
priv can be allocated.
Otherwise, a NULL pointer dereference happens inside
kszphy_config_reset().
Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-2-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e333eed63a091a09bd0db191b7710c594c6e995b upstream.
Since commit f1131b9c23fb ("net: phy: micrel: use
kszphy_suspend()/kszphy_resume for irq aware devices") the following
NULL pointer dereference is observed on a board with KSZ8061:
# udhcpc -i eth0
udhcpc: started, v1.35.0
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = f73cef4e
[00000008] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 196 Comm: ifconfig Not tainted 5.15.37-dirty #94
Hardware name: Freescale i.MX6 SoloX (Device Tree)
PC is at kszphy_config_reset+0x10/0x114
LR is at kszphy_resume+0x24/0x64
...
The KSZ8061 phy_driver structure does not have the .probe/..driver_data
fields, which means that priv is not allocated.
This causes the NULL pointer dereference inside kszphy_config_reset().
Fix the problem by using the generic suspend/resume functions as before.
Another alternative would be to provide the .probe and .driver_data
information into the structure, but to be on the safe side, let's
just restore Ethernet functionality by using the generic suspend/resume.
Cc: stable@vger.kernel.org
Fixes: f1131b9c23fb ("net: phy: micrel: use kszphy_suspend()/kszphy_resume for irq aware devices")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220504143104.1286960-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91a7cda1f4b8bdf770000a3b60640576dafe0cec upstream.
This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000 00000000 00000000 00000000
[ 146.302842] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 146.311281] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Thread 1 (phylib WQ) | Thread 2 (phy interrupt)
|
| phy_interrupt() <-- PHY IRQ
| handle_interrupt()
| phy_read()
| phy_trigger_machine()
| --> schedule phylib WQ
|
|
phy_state_machine() |
phy_check_link_status() |
phy_link_change() |
phydev->adjust_link() |
fec_enet_adjust_link() |
--> FEC reset | phy_interrupt() <-- PHY IRQ
| phy_read()
|
Fix this by acquiring the phydev lock in phy_interrupt().
Link: https://lore.kernel.org/all/20220422152612.GA510015@francesco-nb.int.toradex.com/
Fixes: c974bdbc3e77 ("net: phy: Use threaded IRQ, to allow IRQ from sleeping devices")
cc: <stable@vger.kernel.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220506060815.327382-1-francesco.dolcini@toradex.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2069624dac19d62c558bb6468fe03678553ab01d ]
As noted elsewhere, various GPON SFP modules exhibit non-standard
TX-fault behaviour. In the tested case, the Huawei MA5671A, when used
in combination with a Marvell mv88e6085 switch, was found to
persistently assert TX-fault, resulting in the module being disabled.
This patch adds a quirk to ignore the SFP_F_TX_FAULT state, allowing the
module to function.
Change from v1: removal of erroneous return statment (Andrew Lunn)
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220502223315.1973376-1-mnhagan88@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ed9704b660b259b54743cad8a84a11148f60f0a ]
Return back the error value that we get from phy_read_mmd().
Fixes: c84786fa8f91 ("net: phy: marvell10g: read copper results from CSSR1")
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/f47cb031aeae873bb008ba35001607304a171a20.1650868058.git.baruch@tkos.co.il
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf8bfc4336f7a34e48b3bbd19b1542bf085bdc3d ]
A Broadcom AC201 PHY (same entry as 5241) would be flagged by the
Broadcom UniMAC MDIO controller as not completing the turn around
properly since the PHY expects 65 MDC clock cycles to complete a write
cycle, and the MDIO controller was only sending 64 MDC clock cycles as
determined by looking at a scope shot.
This would make the subsequent read fail with the UniMAC MDIO controller
command field having MDIO_READ_FAIL set and we would abort the
brcm_fet_config_init() function and thus not probe the PHY at all.
After issuing a software reset, wait for at least 1ms which is well
above the 1us reset delay advertised by the datasheet and issue a dummy
read to let the PHY turn around the line properly. This read
specifically ignores -EIO which would be returned by MDIO controllers
checking for the line being turned around.
If we have a genuine reaad failure, the next read of the interrupt
status register would pick it up anyway.
Fixes: d7a2ed9248a3 ("broadcom: Add AC131 phy support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220324232438.1156812-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f3a00c7f5b2cfe4e127fd3fe49b55e1b318c01f ]
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1858c277ba40172005b76a31e6bb931bfc19d9c ]
The driver requires firmware so define MODULE_FIRMWARE so that modinfo
provides the details.
Fixes: fa164e40c53b ("net: phy: mscc: split the driver into separate files")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837d9e49402eaf030db55a49f96fc51d73b4b441 ]
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc162 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.")
Signed-off-by: Kurt Cancemi <kurt@x64architecture.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c87c6f9fbddc5b84d67b2fa3f432fcac6d99d93 ]
Sometimes the link comes up but no data flows. This patch fixes
this behavior. It's not clear what's the root cause of the issue.
According to the tests one other link-up issue remains.
In very rare cases the link isn't even reported as up.
Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
Tested-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/e3473452-a1f9-efcf-5fdd-02b6f44c3fcd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a502a8f04097e038c3daa16c5202a9538116d563 ]
This PHY doesn't support a link-up interrupt source. If aneg is enabled
we use the "aneg complete" interrupt for this purpose, but if aneg is
disabled link-up isn't signaled currently.
According to a vendor driver there's an additional "energy detect"
interrupt source that can be used to signal link-up if aneg is disabled.
We can safely ignore this interrupt source if aneg is enabled.
This patch was tested on a TX3 Mini TV box with S905W (even though
boot message says it's a S905D).
This issue has been existing longer, but due to changes in phylib and
the driver the patch applies only from the commit marked as fixed.
Fixes: 84c8f773d2dc ("net: phy: meson-gxl: remove the use of .ack_callback()")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/04cac530-ea1b-850e-6cfa-144a55c4d75d@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 525b108e6d95b643eccbd84fb10aa9aa101b18dd upstream.
The function mt7531_phy_mode_supported in the DSA driver set supported
mode to PHY_INTERFACE_MODE_GMII instead of PHY_INTERFACE_MODE_INTERNAL
for the internal PHY, so this check breaks the PHY initialization:
mt7530 mdio-bus:00 wan (uninitialized): failed to connect to PHY: -EINVAL
Remove the check to make it work again.
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes: e40d2cca0189 ("net: phy: add MediaTek Gigabit Ethernet PHY driver")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aec12836e7196e4d360b2cbf20cf7aa5139ad2ec upstream.
When setting up autonegotiation for 88E1118R and compatible PHYs,
a software reset of PHY is issued before setting up polarity.
This is incorrect as changes of MDI Crossover Mode bits are
disruptive to the normal operation and must be followed by a
software reset to take effect. Let's patch m88e1118_config_aneg()
to fix the issue mentioned before by invoking software reset
of the PHY just after setting up MDI-x polarity.
Fixes: 605f196efbf8 ("phy: Add support for Marvell 88E1118 PHY")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe4f57bf7b585dca58f1496c4e2481ecbae18126 upstream.
It is mandatory for a software to issue a reset upon modifying RGMII
Receive Timing Control and RGMII Transmit Timing Control bit fields of MAC
Specific Control register 2 (page 2, register 21) otherwise the changes
won't be perceived by the PHY (the same is applicable for a lot of other
registers). Not setting the RGMII delays on the platforms that imply it'
being done on the PHY side will consequently cause the traffic loss. We
discovered that the denoted soft-reset is missing in the
m88e1121_config_aneg() method for the case if the RGMII delays are
modified but the MDIx polarity isn't changed or the auto-negotiation is
left enabled, thus causing the traffic loss on our platform with Marvell
Alaska 88E1510 installed. Let's fix that by issuing the soft-reset if the
delays have been actually set in the m88e1121_config_aneg_rgmii_delays()
method.
Cc: stable@vger.kernel.org
Fixes: d6ab93364734 ("net: phy: marvell: Avoid unnecessary soft reset")
Signed-off-by: Pavel Parkhomenko <Pavel.Parkhomenko@baikalelectronics.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20220205203932.26899-1-Pavel.Parkhomenko@baikalelectronics.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cbda1b16687580d5beee38273f6241ae3725960c ]
Commit bafbdd527d56 ("phylib: Add device reset GPIO support") added call
to phy_device_reset(phydev) after the put_device() call in phy_detach().
The comment before the put_device() call says that the phydev might go
away with put_device().
Fix potential use-after-free by calling phy_device_reset() before
put_device().
Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d15c7e875d44367005370e6a82e8f3a382a04f9b ]
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which
is a 1 Gbps copper module operating in SGMII mode with an internal
BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the
module would work properly on the initial insertion or boot of the
device, but after the device was rebooted, the link would either only
come up at 100 Mbps speeds or go up and down erratically.
I found no meaningful changes in the PHY configuration registers between
the working and non-working boots, but the status registers seemed to
have a lot of error indications set on the SERDES side of the device on
the non-working boot. I suspect the problem is that whatever happens on
the SGMII link when the device is rebooted and the FPGA logic gets
reloaded ends up putting the module's onboard PHY into a bad state.
Since commit 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
the genphy_soft_reset call is not made automatically by the PHY core
unless the callback is explicitly specified in the driver structure. For
most of these Broadcom devices, there is probably a hardware reset that
gets asserted to reset the PHY during boot, however for SFP modules
(where the BCM54616S is commonly found) no such reset line exists, so if
the board keeps the SFP cage powered up across a reboot, it will end up
with no reset occurring during reboots.
Hook up the genphy_soft_reset callback for BCM54616S to ensure that a
PHY reset is performed before the device is initialized. This appears to
fix the issue with erratic operation after a reboot with this SFP
module.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2148927e6ed43a1667baf7c2ae3e0e05a44b51a0 upstream.
Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1131b9c23fb4a3540a774828ff49f421619f902 upstream.
On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().
The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.
Fixes: 59ca4e58b917 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5765cee119bf5a36c94d20eceb37c445508934be upstream.
Commit 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0a3 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <teruyama@springboard-inc.jp>
Tested-by: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f22725c95ececb703c3f741e8f946d23705630b7 ]
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7590fc6f80ac2cbf23e6b42b668bbeded070850b ]
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f20f94f7f52c4685c81754f489ffcc72186e8bdb ]
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 020a45aff1190c32b1087cd75b57fbf6bff46ea6 upstream.
Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dbae3388ea9ca33bd1d5eabc3b0ef17e69c74677 ]
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80662f4fd4771bc9c7cc4abdfbe866ebd1179621 ]
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4db9055fdb9cf607775c66d39796caf6439ec92 ]
As reported by Zhang there's a small issue if in forced mode the duplex
mode changes with the link staying up [0]. In this case the MAC isn't
notified about the change.
The proposed patch relies on the phylib state machine and ignores the
fact that there are drivers that uses phylib but not the phylib state
machine. So let's don't change the behavior for such drivers and fix
it w/o re-adding state PHY_FORCING for the case that phylib state
machine is used.
[0] https://lore.kernel.org/netdev/a5c26ffd-4ee4-a5e6-4103-873208ce0dc5@huawei.com/T/
Fixes: 2bd229df5e2e ("net: phy: remove state PHY_FORCING")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7b8b9456-a93f-abbc-1dc5-a2c2542f932c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd8d9731bcdfb22d28e45bce789bcb211c868c78 ]
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2641b62d2fab52648e34cdc6994b2eacde2d27c1 ]
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6a2 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbcca2e3961eac736566ac13ef0d0bf6f0b764ec ]
Dan Carpenter points out that we have a code path that permits a NULL
netdev pointer to be passed to netif_carrier_off(), which will cause
a kernel oops. In any case, we need to set pl->old_link_state to false
to have the desired effect when there is no netdev present.
Fixes: f97493657c63 ("net: phylink: add suspend/resume support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67ca5159dbe2edb5dae7544447b8677d2596933a ]
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY device was probed thus in the PHY_READY state, but not
configured and with no network device attached yet, we should not be
trying to shut it down because it has been brought back into reset by
phy_device_reset() towards the end of phy_probe() and anyway we have not
configured the PHY yet.
Fixes: e2f016cf7751 ("net: phy: add a shutdown procedure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting
a new value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change
event notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup
on device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly
respond to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it
only in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xzZg
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from xfrm, bpf, netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new
value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with
nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change event
notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup on
device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly respond
to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it only
in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic"
* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
net: prefer socket bound to interface when not in VRF
iavf: fix double unlock of crit_lock
i40e: Fix freeing of uninitialized misc IRQ vector
i40e: fix endless loop under rtnl
dt-bindings: net: dsa: marvell: fix compatible in example
ionic: move filter sync_needed bit set
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
gve: fix gve_get_stats()
rtnetlink: fix if_nlmsg_stats_size() under estimation
gve: Properly handle errors in gve_assign_qpl
gve: Avoid freeing NULL pointer
gve: Correct available tx qpl check
unix: Fix an issue in unix_shutdown causing the other end read/write failures
net: stmmac: trigger PCS EEE to turn off on link down
net: pcs: xpcs: fix incorrect steps on disable EEE
netlink: annotate data races around nlk->bound
net: pcs: xpcs: fix incorrect CL37 AN sequence
net: sfp: Fix typo in state machine debug string
net/sched: sch_taprio: properly cancel timer from taprio_destroy()
net: bridge: fix under estimation in br_get_linkxstats_size()
...
The string should be "tx_disable" to match the state enum.
Fixes: 4005a7cb4f55 ("net: phy: sftp: print debug message with text, not numbers")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has
been reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYVmC1A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfCQCgtQ0kdPoPdUG6mPCn45rrbJQLBY4AnRL5JyhO
zB60l6C2EHHnLnRxMnQq
=gygB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has been
reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues"
* tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: also call kernfs_set_rev() for positive dentry
driver core: Add debug logs when fwnode links are added/deleted
driver core: Create __fwnode_link_del() helper function
driver core: Set deferred probe reason when deferred by driver core
net: mdiobus: Set FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for mdiobus parents
driver core: fw_devlink: Add support for FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD
driver core: fw_devlink: Improve handling of cyclic dependencies
cpumask: Omit terminating null byte in cpumap_print_{list,bitmask}_to_buf
debugfs: debugfs_create_file_size(): use IS_ERR to check for error
Syzbot reported memory leak in MDIO bus interface, the problem was in
wrong state logic.
MDIOBUS_ALLOCATED indicates 2 states:
1. Bus is only allocated
2. Bus allocated and __mdiobus_register() fails, but
device_register() was called
In case of device_register() has been called we should call put_device()
to correctly free the memory allocated for this device, but mdiobus_free()
calls just kfree(dev) in case of MDIOBUS_ALLOCATED state
To avoid this behaviour we need to set bus->state to MDIOBUS_UNREGISTERED
_before_ calling device_register(), because put_device() should be
called even in case of device_register() failure.
Link: https://lore.kernel.org/netdev/YVMRWNDZDUOvQjHL@shell.armlinux.org.uk/
Fixes: 46abc02175b3 ("phylib: give mdio buses a device tree presence")
Reported-and-tested-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/eceae1429fbf8fa5c73dd2a0d39d525aa905074d.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit ab609f25d19858513919369ff3d9a63c02cd9e2e.
This patch is correct in the sense that we _should_ call device_put() in
case of device_register() failure, but the problem in this code is more
vast.
We need to set bus->state to UNMDIOBUS_REGISTERED before calling
device_register() to correctly release the device in mdiobus_free().
This patch prevents us from doing it, since in case of device_register()
failure put_device() will be called 2 times and it will cause UAF or
something else.
Also, Reported-by: tag in revered commit was wrong, since syzbot
reported different leak in same function.
Link: https://lore.kernel.org/netdev/20210928092657.GI2048@kadam/
Acked-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/f12fb1faa4eccf0f355788225335eb4309ff2599.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
