IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 2dd8a74fddd21b95dcc60a2d3c9eaec993419d69 upstream.
RTS polarity of rs485-enabled ports is currently initialized on uart
open via:
tty_port_open()
tty_port_block_til_ready()
tty_port_raise_dtr_rts() # if (C_BAUD(tty))
uart_dtr_rts()
uart_port_dtr_rts()
There's at least three problems here:
First, if no baud rate is set, RTS polarity is not initialized.
That's the right thing to do for rs232, but not for rs485, which
requires that RTS is deasserted unconditionally.
Second, if the DeviceTree property "linux,rs485-enabled-at-boot-time" is
present, RTS should be deasserted as early as possible, i.e. on probe.
Otherwise it may remain asserted until first open.
Third, even though RTS is deasserted on open and close, it may
subsequently be asserted by uart_throttle(), uart_unthrottle() or
uart_set_termios() because those functions aren't rs485-aware.
(Only uart_tiocmset() is.)
To address these issues, move RTS initialization from uart_port_dtr_rts()
to uart_configure_port(). Prevent subsequent modification of RTS
polarity by moving the existing rs485 check from uart_tiocmget() to
uart_update_mctrl().
That way, RTS is initialized on probe and then remains unmodified unless
the uart transmits data. If rs485 is enabled at runtime (instead of at
boot) through a TIOCSRS485 ioctl(), RTS is initialized by the uart
driver's ->rs485_config() callback and then likewise remains unmodified.
The PL011 driver initializes RTS on uart open and prevents subsequent
modification in its ->set_mctrl() callback. That code is obsoleted by
the present commit, so drop it.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2d2acaf3a69e89b7bf687c912022b11fd29dfa1e.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be03b0651ffd8bab69dfd574c6818b446c0753ce upstream.
Not all LSR register flags are preserved across reads. Therefore, LSR
readers must store the non-preserved bits into lsr_save_flags.
This fix was initially mixed into feature commit f6f586102add ("serial:
8250: Handle UART without interrupt on TEMT using em485"). However,
that feature change had a flaw and it was reverted to make room for
simpler approach providing the same feature. The embedded fix got
reverted with the feature change.
Re-add the lsr_save_flags fix and properly mark it's a fix.
Link: https://lore.kernel.org/all/1d6c31d-d194-9e6a-ddf9-5f29af829f3@linux.intel.com/T/#m1737eef986bd20cf19593e344cebd7b0244945fc
Fixes: e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
Cc: stable <stable@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@penugtronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/f4d774be-1437-a550-8334-19d8722ab98c@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e74024b2eccbb784824a0f9feaeaaa3b47514b79 upstream.
Dan Carpenter <dan.carpenter@oracle.com> reported the following Smatch
warning:
drivers/tty/n_gsm.c:720 gsm_data_kick()
warn: sleeping in atomic context
This is because gsm_control_message() is holding a spin lock so
gsm_hex_dump_bytes() needs to use GFP_ATOMIC instead of GFP_KERNEL.
Fixes: 925ea0fa5277 ("tty: n_gsm: Fix packet data hex dump output")
Cc: stable <stable@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220523155052.57129-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aabdbb1b7a5819e18c403334a31fb0cc2c06ad41 ]
__msm_console_write() assumes that interrupts are disabled, but
with threaded console printers it is possible that the write()
callback of the console is called with interrupts enabled.
Explicitly disable interrupts using local_irq_save() to preserve
the assumed context.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20220506213324.470461-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b2caef400c1738b6d22f636c628d9f85cd4c4c ]
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 689ca31c542687709ba21ec2195c1fbce34fd029 ]
When the driver fails at alloc_hdlcdev(), and then we remove the driver
module, we will get the following splat:
[ 25.065966] general protection fault, probably for non-canonical address 0xdffffc0000000182: 0000 [#1] PREEMPT SMP KASAN PTI
[ 25.066914] KASAN: null-ptr-deref in range [0x0000000000000c10-0x0000000000000c17]
[ 25.069262] RIP: 0010:detach_hdlc_protocol+0x2a/0x3e0
[ 25.077709] Call Trace:
[ 25.077924] <TASK>
[ 25.078108] unregister_hdlc_device+0x16/0x30
[ 25.078481] slgt_cleanup+0x157/0x9f0 [synclink_gt]
Fix this by checking whether the 'info->netdev' is a null pointer first.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/20220410114814.3920474-1-zheyuma97@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1deeda8d2877c18bc2b9eeee10dd6d2628852848 ]
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d043947b (serial: stm32: fix word length configuration)
Cc: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52bb1cb7118564166b04d52387bd8403632f5190 ]
Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or
CS6 to CS8. In addition, ASC_CTL_MODE_7BIT_PAR suggests that CS7 has
to have parity, thus add PARENB.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c4b058560762 (serial:st-asc: Add ST ASC driver.)
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c069d2756c01ed36121fae6a42c14fdf1325c71d ]
Only CS8 is supported but CSIZE was not sanitized to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Similarly, INPCK, PARMRK, and BRKINT are reported textually unsupported
but were not cleared in termios c_iflag which is the machine-readable
format.
Fixes: 45c054d0815b (tty: serial: add driver for the SiFive UART)
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b87162de8be26bf3156460b37deee6399fd0fcb ]
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79ac88655dc0551e3571ad16bdabdbe65d61553e ]
Only CS7 and CS8 are supported but CSIZE is not sanitized with
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 098333a9c7d12bb3ce44c82f08b4d810c44d31b0 ]
Only CS7 and CS8 are supported but CSIZE is not sanitized after
fallthrough from CS5 or CS6 to CS7.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c10b13325ced (tty: serial: Add RDA8810PL UART driver)
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd63031b8c0763addcecdefe0e0c59d49646204e ]
Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
the default: block.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 5930cb3511df (serial: driver for Conexant Digicolor USART)
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0258502f11a4f6036b5f8b34b09027c8a92def3a ]
drivers/tty/serial/cpm_uart/cpm_uart_core.c: In function ‘cpm_uart_init_port’:
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1251:7: error: ‘udbg_port’ undeclared (first use in this function); did you mean ‘uart_port’?
if (!udbg_port)
^~~~~~~~~
uart_port
commit d142585bceb3 leave this corner, wrap it with #ifdef block
Fixes: d142585bceb3 ("serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20220518135452.39480-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af0179270977508df6986b51242825d7edd59caf ]
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
Fixes: 7ecc77011c6f ("serial: 8250_fintek: Return -EINVAL on invalid configuration")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/035c738-8ea5-8b17-b1d7-84a7b3aeaa51@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 589f892ac8ef244e47c5a00ffd8605daa1eaef8e ]
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
CPU0 CPU1
meson_serial_console_write meson_uart_startup
-------------------------- ------------------
spin_lock(port->lock)
val = readl(AML_UART_CONTROL)
uart_console_write()
writel(INT_EN, AML_UART_CONTROL)
writel(val, AML_UART_CONTROL)
spin_unlock(port->lock)
Add port->lock synchronization to meson_uart_startup() to avoid
racing with meson_serial_console_write().
Also add detailed comments to meson_uart_reset() explaining why it
is *not* using port->lock synchronization.
Link: https://lore.kernel.org/lkml/2a82eae7-a256-f70c-fd82-4e510750906e@samsung.com
Fixes: ff7693d079e5 ("ARM: meson: serial: add MesonX SoC on-chip uart driver")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20220508103547.626355-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 925ea0fa5277c1e6bb9e51955ef34eea9736c3d7 ]
The module param debug for n_gsm uses KERN_INFO level, but the hexdump
now uses KERN_DEBUG level. This started after commit 091cb0994edd
("lib/hexdump: make print_hex_dump_bytes() a nop on !DEBUG builds").
We now use dynamic_hex_dump() unless DEBUG is set.
This causes no packets to be seen with modprobe n_gsm debug=0x1f unlike
earlier. Let's fix this by adding gsm_hex_dump_bytes() that calls
print_hex_dump() with KERN_INFO to match what n_gsm is doing with the
other debug related output.
Fixes: 091cb0994edd ("lib/hexdump: make print_hex_dump_bytes() a nop on !DEBUG builds")
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220512131506.1216-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9136c68346d096697935b9840782f7051d5796c5 ]
We currently have gsmld_output() ignore the return value from device
write. This means we will lose packets if device write returns 0 or
an error.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210930060624.46523-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a7ff843d507ce2cca2c3b7e169ee56e28133530 ]
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
References:
[1] "SiFive FU740-C000 Manual", v1p3, SiFive, Inc., August 13, 2021,
Section 16.9 "Baud Rate Divisor Register (div)", pp.143-144
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1f1496a923b6 ("riscv: Fix sifive serial driver")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656280.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f398e0aa325c61fa20903833a5b534ecb8e6e418 ]
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0fd55719fa081de6f9e5d9e6cef48efb04d34a ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference.
Fixes: 54da3e381c2b ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404143842.16960-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65a8b287023da68c4550deab5c764e6891cf1caf ]
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a03 ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 359303076163 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Fixes: 359303076163 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Gibson <daniel@gibson.sh>
Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 507b05063d1b7a1fcb9f7d7c47586fc4f3508f98 ]
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
Fix the above by calling tty_port_destroy().
Fixes: 666b7793d4bf ("goldfish: tty driver")
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com>
Link: https://lore.kernel.org/r/20220328115844.86032-1-wangweiyang2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d9f3af4fbb1d955bbaf872d9e76502f6e3e803cb upstream.
When x_char is to be sent, the TX path overwrites whatever is in the
circular buffer at offset 0 with x_char and sends it using
pch_uart_hal_write(). I don't understand how this was supposed to work
if xmit->buf[0] already contained some character. It must have been
lost.
Remove this whole pop_tx_x() concept and do the work directly in the
callers. (Without printing anything using dev_dbg().)
Cc: <stable@vger.kernel.org>
Fixes: 3c6a483275f4 (Serial: EG20T: add PCH_UART driver)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220503080808.28332-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e2ac4a3327479f7e2744cdd88a5c823f2057bad upstream.
The goldfish TTY device was clearly defined as having little-endian
registers, but the switch to __raw_{read,write}l(() broke its driver
when running on big-endian kernels (if anyone ever tried this).
The m68k qemu implementation got this wrong, and assumed native-endian
registers. While this is a bug in qemu, it is probably impossible to
fix that since there is no way of knowing which other operating systems
have started relying on that bug over the years.
Hence revert commit da31de35cd2f ("tty: goldfish: use
__raw_writel()/__raw_readl()", and define gf_ioread32()/gf_iowrite32()
to be able to use accessors defined by the architecture.
Cc: stable@vger.kernel.org # v5.11+
Fixes: da31de35cd2fb78f ("tty: goldfish: use __raw_writel()/__raw_readl()")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Link: https://lore.kernel.org/r/20220406201523.243733-2-laurent@vivier.eu
[geert: Add rationale based on Arnd's comments]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b9dbedbe3499fef862c4dff5217cf91f34e43b3 ]
pty_write() invokes kmalloc() which may invoke a normal printk() to print
failure message. This can cause a deadlock in the scenario reported by
syz-bot below:
CPU0 CPU1 CPU2
---- ---- ----
lock(console_owner);
lock(&port_lock_key);
lock(&port->lock);
lock(&port_lock_key);
lock(&port->lock);
lock(console_owner);
As commit dbdda842fe96 ("printk: Add console owner and waiter logic to
load balance console writes") said, such deadlock can be prevented by
using printk_deferred() in kmalloc() (which is invoked in the section
guarded by the port->lock). But there are too many printk() on the
kmalloc() path, and kmalloc() can be called from anywhere, so changing
printk() to printk_deferred() is too complicated and inelegant.
Therefore, this patch chooses to specify __GFP_NOWARN to kmalloc(), so
that printk() will not be called, and this deadlock problem can be
avoided.
Syzbot reported the following lockdep error:
======================================================
WARNING: possible circular locking dependency detected
5.4.143-00237-g08ccc19a-dirty #10 Not tainted
------------------------------------------------------
syz-executor.4/29420 is trying to acquire lock:
ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: console_trylock_spinning kernel/printk/printk.c:1752 [inline]
ffffffff8aedb2a0 (console_owner){....}-{0:0}, at: vprintk_emit+0x2ca/0x470 kernel/printk/printk.c:2023
but task is already holding lock:
ffff8880119c9158 (&port->lock){-.-.}-{2:2}, at: pty_write+0xf4/0x1f0 drivers/tty/pty.c:120
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&port->lock){-.-.}-{2:2}:
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159
tty_port_tty_get drivers/tty/tty_port.c:288 [inline] <-- lock(&port->lock);
tty_port_default_wakeup+0x1d/0xb0 drivers/tty/tty_port.c:47
serial8250_tx_chars+0x530/0xa80 drivers/tty/serial/8250/8250_port.c:1767
serial8250_handle_irq.part.0+0x31f/0x3d0 drivers/tty/serial/8250/8250_port.c:1854
serial8250_handle_irq drivers/tty/serial/8250/8250_port.c:1827 [inline] <-- lock(&port_lock_key);
serial8250_default_handle_irq+0xb2/0x220 drivers/tty/serial/8250/8250_port.c:1870
serial8250_interrupt+0xfd/0x200 drivers/tty/serial/8250/8250_core.c:126
__handle_irq_event_percpu+0x109/0xa50 kernel/irq/handle.c:156
[...]
-> #1 (&port_lock_key){-.-.}-{2:2}:
__raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:110 [inline]
_raw_spin_lock_irqsave+0x35/0x50 kernel/locking/spinlock.c:159
serial8250_console_write+0x184/0xa40 drivers/tty/serial/8250/8250_port.c:3198
<-- lock(&port_lock_key);
call_console_drivers kernel/printk/printk.c:1819 [inline]
console_unlock+0x8cb/0xd00 kernel/printk/printk.c:2504
vprintk_emit+0x1b5/0x470 kernel/printk/printk.c:2024 <-- lock(console_owner);
vprintk_func+0x8d/0x250 kernel/printk/printk_safe.c:394
printk+0xba/0xed kernel/printk/printk.c:2084
register_console+0x8b3/0xc10 kernel/printk/printk.c:2829
univ8250_console_init+0x3a/0x46 drivers/tty/serial/8250/8250_core.c:681
console_init+0x49d/0x6d3 kernel/printk/printk.c:2915
start_kernel+0x5e9/0x879 init/main.c:713
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241
-> #0 (console_owner){....}-{0:0}:
[...]
lock_acquire+0x127/0x340 kernel/locking/lockdep.c:4734
console_trylock_spinning kernel/printk/printk.c:1773 [inline] <-- lock(console_owner);
vprintk_emit+0x307/0x470 kernel/printk/printk.c:2023
vprintk_func+0x8d/0x250 kernel/printk/printk_safe.c:394
printk+0xba/0xed kernel/printk/printk.c:2084
fail_dump lib/fault-inject.c:45 [inline]
should_fail+0x67b/0x7c0 lib/fault-inject.c:144
__should_failslab+0x152/0x1c0 mm/failslab.c:33
should_failslab+0x5/0x10 mm/slab_common.c:1224
slab_pre_alloc_hook mm/slab.h:468 [inline]
slab_alloc_node mm/slub.c:2723 [inline]
slab_alloc mm/slub.c:2807 [inline]
__kmalloc+0x72/0x300 mm/slub.c:3871
kmalloc include/linux/slab.h:582 [inline]
tty_buffer_alloc+0x23f/0x2a0 drivers/tty/tty_buffer.c:175
__tty_buffer_request_room+0x156/0x2a0 drivers/tty/tty_buffer.c:273
tty_insert_flip_string_fixed_flag+0x93/0x250 drivers/tty/tty_buffer.c:318
tty_insert_flip_string include/linux/tty_flip.h:37 [inline]
pty_write+0x126/0x1f0 drivers/tty/pty.c:122 <-- lock(&port->lock);
n_tty_write+0xa7a/0xfc0 drivers/tty/n_tty.c:2356
do_tty_write drivers/tty/tty_io.c:961 [inline]
tty_write+0x512/0x930 drivers/tty/tty_io.c:1045
__vfs_write+0x76/0x100 fs/read_write.c:494
[...]
other info that might help us debug this:
Chain exists of:
console_owner --> &port_lock_key --> &port->lock
Link: https://lkml.kernel.org/r/20220511061951.1114-2-zhengqi.arch@bytedance.com
Link: https://lkml.kernel.org/r/20220510113809.80626-2-zhengqi.arch@bytedance.com
Fixes: b6da31b2c07c ("tty: Fix data race in tty_insert_flip_string_fixed_flag")
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e1bfdbc7daca171c74a577b3dd0b36d76bb0ffcc upstream.
The XON1/XOFF1 character registers are at offset 0xa0 and 0xa8
respectively, so we cannot use the definition in serial_port.h.
Fixes: bdbd0a7f8f03 ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb0b197aadd928f52ce6f01f0ee977f0a08cf1be upstream.
On MediaTek SoCs, the UART IP is 16550A compatible, but there are some
specific quirks: we are declaring a register shift of 2, but this is
only valid for the majority of the registers, as there are some that
are out of the standard layout.
Specifically, this driver is using definitions from serial_reg.h, where
we have a UART_EFR register defined as 2: this results in a 0x8 offset,
but there we have the FCR register instead.
The right offset for the EFR register on MediaTek UART is at 0x98,
so, following the decimal definition convention in serial_reg.h and
accounting for the register left shift of two, add and use the correct
register address for this IP, defined as decimal 38, so that the final
calculation results in (0x26 << 2) = 0x98.
Fixes: bdbd0a7f8f03 ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 401fb66a355eb0f22096cf26864324f8e63c7d78 upstream.
If an irq is pending when devm_request_irq() is called, the irq
handler will cause a NULL pointer access because initialisation
is not done yet.
Fixes: 9d7ee0e28da59 ("tty: serial: lpuart: avoid report NULL interrupt")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Indan Zupancic <Indan.Zupancic@mep-info.com>
Link: https://lore.kernel.org/r/20220505114750.45423-1-Indan.Zupancic@mep-info.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit edd5f60c340086891fab094ad61270d6c80f9ca4 upstream.
The current implementation activates the mux if it was restarted and opens
the control channel if the mux was previously closed and we are now acting
as initiator instead of responder, which is the default setting.
This has two issues.
1) No mux is activated if we keep all default values and only switch to
initiator. The control channel is not allocated but will be opened next
which results in a NULL pointer dereference.
2) Switching the configuration after it was once configured while keeping
the initiator value the same will not reopen the control channel if it was
closed due to parameter incompatibilities. The mux remains dead.
Fix 1) by always activating the mux if it is dead after configuration.
Fix 2) by always opening the control channel after mux activation.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd442e5ba30aaa75ea47b32149e7a3110dc20a46 upstream.
'len' is decreased after each octet that has its EA bit set to 0, which
means that the value is encoded with additional octets. However, the final
octet does not decreases 'len' which results in 'len' being one byte too
long. A buffer over-read may occur in tty_insert_flip_string() as it tries
to read one byte more than the passed content size of 'data'.
Decrease 'len' also for the final octet which has the EA bit set to 1 to
write the correct number of bytes from the internal receive buffer to the
virtual tty.
Fixes: 2e124b4a390c ("TTY: switch tty_flip_buffer_push")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 447ee1516f19f534a228dda237eddb202f23e163 upstream.
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: 5930cb3511df ("serial: driver for Conexant Digicolor USART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220505124621.1592697-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4f7d63287217ba25e5c80f5faae5e4f7118790e upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff9166c623704337bd6fe66fce2838d9768a6634 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-20-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73029a4d7161f8b6c0934553145ef574d2d0c645 upstream.
gsmtty_write() and gsm_dlci_data_output() properly guard the fifo access.
However, gsm_dlci_close() and gsmtty_flush_buffer() modifies the fifo but
do not guard this.
Add a guard here to prevent race conditions on parallel writes to the fifo.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-17-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1adf6fee58ca25fb6720b8d34c919dcf5425cc9c upstream.
gsm_control_modem() informs the virtual tty that more data can be written
after receiving a control signal octet via modem status command (MSC).
However, gsm_dlci_data() fails to do the same after receiving a control
signal octet from the convergence layer type 2 header.
Add tty_wakeup() in gsm_dlci_data() for convergence layer type 2 to fix
this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-14-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 317f86af7f5d19f286ed2d181cbaef4a188c7f19 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. The value of the modem status command (MSC) frame
contains an address field, control signal and optional break signal octet.
The address field is encoded as described in chapter 5.2.1.2 with only one
octet (may be extended to more in future versions of the standard). Whereas
the control signal and break signal octet are always one byte each. This is
strange at first glance as it makes the EA bit redundant. However, the same
two octets are also encoded as header in convergence layer type 2 as
described in chapter 5.5.2. No header length field is given and the only
way to test if there is an optional break signal octet is via the EA flag
which extends the control signal octet with a break signal octet. Now it
becomes obvious how the EA bit for those two octets shall be encoded in the
MSC frame. The current implementation treats the signal octet different for
MSC frame and convergence layer type 2 header even though the standard
describes it for both in the same way.
Use the EA bit to encode the signal octets not only in the convergence
layer type 2 header but also in the MSC frame in the same way with either
1 or 2 bytes in case of an optional break signal. Adjust the receiving path
accordingly in gsm_control_modem().
Fixes: 3ac06b905655 ("tty: n_gsm: Fix for modems with brk in modem status control")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-13-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 398867f59f956985f4c324f173eff7b946e14bd8 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-12-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0bcdffcad5a22f202e3bf37190c0dd8c080ea92 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-11-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17eac652028501df7ea296b1d9b9c134db262b7d upstream.
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-10-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit deefc58bafb4841df7f0a0d85d89a1c819db9743 upstream.
The current DLCI release order starts with the control channel followed by
the user channels. Reverse this order to keep the control channel open
until all user channels have been released.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 535bf600de75a859698892ee873521a48d289ec1 upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-8-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a24b4b2f660b7ddf3f484b37600bba382cb28a9d upstream.
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 06d5afd4d640eea67f5623e76cd5fc03359b7f3c upstream.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 284260f278b706364fb4c88a7b56ba5298d5973c upstream.
Internally, we manage the alive state of the mux channels and mux itself
with the field member 'dead'. This makes it possible to notify the user
if the accessed underlying link is already gone. On the other hand,
however, removing the virtual ttys before terminating the channels may
result in peer messages being received without any internal target. Move
the mux cleanup procedure from gsmld_detach_gsm() to gsmld_close() to fix
this by keeping the virtual ttys open until the mux has been cleaned up.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1ec92e9742774bf42614fceea3bf6b50c9409225 upstream.
The active mux instances are managed in the gsm_mux array and via mux_get()
and mux_put() functions separately. This gives a very loose coupling
between the actual instance and the gsm_mux array which manages it. It also
results in unnecessary lockings which makes it prone to failures. And it
creates a race condition if more than the maximum number of mux instances
are requested while the user changes the parameters of an active instance.
The user may loose ownership of the current mux instance in this case.
Fix this by moving the gsm_mux array handling to the mux allocation and
deallocation functions.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220414094225.4527-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
