IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 7f41d52ced9e1b7ed4ff8e1ae9cacbf46b64e6db ]
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-7-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 279d626d737486363233b9b99c30b5696c389b41 ]
Fix low limit for CPU regulator. Otherwise setting voltages lower than
1.125V will not be allowed (CPUFreq will not be allowed to set proper
voltages on proper frequencies).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220113144900.906370-7-claudiu.beznea@microchip.com
Stable-dep-of: 7f41d52ced9e ("ARM: dts: at91: sama7g5ek: specify proper regulator output ranges")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af7d78c957017f8b3a0986769f6f18e57f9362ea ]
Drop the "winbond,w25q16dw" compatible since it causes to set the
MODALIAS to w25q16dw which is not specified within spi-nor id table.
Fix this by use the common "jedec,spi-nor" compatible.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d074b750d2b4c91962f10ea1df1c289ce0d3ce8 ]
VDD_OTHER is not connected to any on board consumer thus it is not
needed to keep it enabled all the time.
Fixes: 68a95ef72cef ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-9-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 617a0d9fe6867bf5b3b7272629cd780c27c877d9 ]
ldo2 is not used by any consumer on sama5d27_wlsom1 board, thus
don't keep it enabled all the time.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-8-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7737d93666eea282febf95e5fa3b3fde1f2549f3 ]
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 68a95ef72cef ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-6-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit addf7efec23af2b67547800aa232d551945e7de2 ]
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-5-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e24c75f02a81d6ddac0072cbd7a03e799c19d558 ]
This was fixed wrong so fix it. Now verified by using
iio-sensor-proxy monitor-sensor test program.
Link: https://lore.kernel.org/r/20220611205138.491513-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b2152e428ab91533a02888ff24e52e788dc4637 ]
This was fixed wrong so fix it again. Now verified by using
iio-sensor-proxy monitor-sensor test program.
Link: https://lore.kernel.org/r/20220611204249.472250-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 935327a73553001f8d81375c76985d05f604507f ]
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c6cf86e1ab433b2d421880fdd9c6e954f404948 ]
imx6ul is not compatible to imx6sx, both have different erratas.
Fixes the dt_binding_check warning:
spi@21e0000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-qspi', 'fsl,imx6sx-qspi'] is too long
Additional items are not allowed ('fsl,imx6sx-qspi' was unexpected)
'fsl,imx6ul-qspi' is not one of ['fsl,ls1043a-qspi']
'fsl,imx6ul-qspi' is not one of ['fsl,imx8mq-qspi']
'fsl,ls1021a-qspi' was expected
'fsl,imx7d-qspi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a884d17ca324531634cce82e9f64c0302bdf7de ]
In yaml binding "fsl,imx6ul-lcdif" is listed as compatible to imx6sx-lcdif,
but not imx28-lcdif. Change the list accordingly. Fixes the
dt_binding_check warning:
lcdif@21c8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-lcdif', 'fsl,imx28-lcdif'] is too long
Additional items are not allowed ('fsl,imx28-lcdif' was unexpected)
'fsl,imx6ul-lcdif' is not one of ['fsl,imx23-lcdif', 'fsl,imx28-lcdif',
'fsl,imx6sx-lcdif']
'fsl,imx6sx-lcdif' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0aca931a2c7c29c88ebf37f9c3cd045e083483d ]
"fsl,imx6ul-csi" was never listed as compatible to "fsl,imx7-csi", neither
in yaml bindings, nor previous txt binding. Remove the imx7 part. Fixes
the dt schema check warning:
csi@21c4000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-csi', 'fsl,imx7-csi'] is too long
Additional items are not allowed ('fsl,imx7-csi' was unexpected)
'fsl,imx8mm-csi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d15e0c9a515494af2e3199741cdac7002928a0e ]
According to binding, the compatible shall only contain imx6ul and imx21
compatibles. Fixes the dt_binding_check warning:
keypad@20b8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-kpp', 'fsl,imx6q-kpp', 'fsl,imx21-kpp'] is too long
Additional items are not allowed ('fsl,imx6q-kpp', 'fsl,imx21-kpp' were
unexpected)
Additional items are not allowed ('fsl,imx21-kpp' was unexpected)
'fsl,imx21-kpp' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edb67843983bbdf61b4c8c3c50618003d38bb4ae ]
operating-points is a uint32-matrix as per opp-v1.yaml. Change it
accordingly. While at it, change fsl,soc-operating-points as well,
although there is no bindings file (yet). But they should have the same
format. Fixes the dt_binding_check warning:
cpu@0: operating-points:0: [696000, 1275000, 528000, 1175000, 396000,
1025000, 198000, 950000] is too long
cpu@0: operating-points:0: Additional items are not allowed (528000,
1175000, 396000, 1025000, 198000, 950000 were unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5655699cf5cff9f4c4ee703792156bdd05d1addf ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check
warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9b0dc7abb5cc43a2dbf90690c3c6011dcadc574d upstream.
An interrupt for USB device are shared with USB host. Set interrupt-names
property to common "dwc_usb3" instead of "host" and "peripheral".
Cc: stable@vger.kernel.org
Fixes: 45be1573ad19 ("ARM: dts: uniphier: Add USB3 controller nodes")
Reported-by: Ryuta NAKANISHI <nakanishi.ryuta@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 78ece8cce1ba0c3f3e5a7c6c1b914b3794f04c44 ]
The peripheral clock of CEC is not LSE but CEC.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 884b66976a7279ee889ba885fe364244d50b79e7 ]
The device tree should include generic "jedec,spi-nor" compatible, and a
manufacturer-specific one.
The macronix part is what is shipped on the boards that come with a
flash chip.
Fixes: 45857ae95478 ("ARM: dts: orange-pi-zero: add node for SPI NOR")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708174529.3360-1-msuchanek@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d0c1aadf1fd9f3de95d1532b3651e8634546e71 ]
The USBH composed of EHCI and OHCI controllers needs the PHY clock to be
initialized first, before enabling (gating) them. The reverse is also
required when going to suspend.
So, add USBPHY clock as 1st entry in both controllers, so the USBPHY PLL
gets enabled 1st upon controller init. Upon suspend/resume, this also makes
the clock to be disabled/re-enabled in the correct order.
This fixes some IRQ storm conditions seen when going to low-power, due to
PHY PLL being disabled before all clocks are cleanly gated.
Fixes: 949a0c0dec85 ("ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c")
Fixes: db7be2cb87ae ("ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db7be2cb87ae65e2d033a9f61f7fb94bce505177 ]
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 416ce193d73a734ded6d09fe141017b38af1c567 ]
The eeprom memories on the board are microchip 24aa025e48, which are 2 Kbits
and are compatible with at24c02 not at24c32.
Fixes: 68a95ef72cefe ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220607090455.80433-2-eugen.hristev@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2cbbc3f926316ccf8ef9363d8a60c1110afc1c7 ]
The board has a microchip 24aa025e48 eeprom, which is a 2 Kbits memory,
so it's compatible with at24c02 not at24c32.
Also the size property is wrong, it's not 128 bytes, but 256 bytes.
Thus removing and leaving it to the default (256).
Fixes: 1e5f532c27371 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220607090455.80433-1-eugen.hristev@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b9b6d4c925604b70d007feb4c77b8cc4c038d2da upstream.
The GPIO expander line names has been fixed in the vendor tree last year,
so upstream these changes.
Fixes: 1c701accecf2 ("ARM: dts: Add Raspberry Pi 400 support")
Reported-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93a8ba2a619816d631bd69e9ce2172b4d7a481b8 upstream.
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f72 ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552ca27929ab28b341ae9b2629f0de3a84c98ee8 upstream.
Move the power domain to its actual user. This keeps the power domain
enabled even when the USB host is runtime suspended. This is necessary
to detect any downstream events, like device attach.
Fixes: 02f8eb40ef7b ("ARM: dts: imx7s: Add power domain for imx7d HSIC")
Suggested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d338ee40ba89e508c5d3e1b4af956af7cb5e12e ]
Since mac0/1 and mac2/3 are physically located on different die,
they have different properties by nature, which is mac0/1 has smaller delay step.
The property 'phy-mode' on ast2600 mac0 and mac1 is recommended to set to 'rgmii-rxid'
which enables the RX interface delay from the PHY chip.
Refer page 45 of SDK User Guide v08.00
https://github.com/AspeedTech-BMC/openbmc/releases/download/v08.00/SDK_User_Guide_v08.00.pdf
Fixes: 2ca5646b5c2f ("ARM: dts: aspeed: Add AST2600 and EVB")
Signed-off-by: Howard Chiu <howard_chiu@aspeedtech.com>
Link: https://lore.kernel.org/r/SG2PR06MB23152A548AAE81140B57DD69E6E09@SG2PR06MB2315.apcprd06.prod.outlook.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 096f58507374e1293a9e9cff8a1ccd5f37780a20 upstream.
Since commit 766c6b63aa04 ("spi: fix client driver breakages when using
GPIO descriptors"), the panel has been blank due to an inverted CS GPIO.
In order to correct this, drop the spi-cs-high from the panel SPI device.
Fixes: 766c6b63aa04 ("spi: fix client driver breakages when using GPIO descriptors")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB05670C771062570E911AF3B4CB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b7e86ef7afd128577ff7bb0db0ae82d27d7ed7ad ]
interrupt-parent is not to be used as a boolean property.
It is already present in the DT in the proper way it's supposed to be used:
interrupt-parent = <&gic>;
This is also reported by dtbs_check:
arch/arm/boot/dts/at91-sama7g5ek.dtb: interrupt-controller@e8c11000: interrupt-parent: True is not of type 'array'
From schema: /.local/lib/python3.8/site-packages/dtschema/schemas/interrupts.yaml
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220503133127.64320-1-eugen.hristev@microchip.com
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97bd8659c1c46c23e4daea7e040befca30939950 ]
Recently this has been fixed in the vendor tree, so upstream this.
Fixes: 731b26a6ac17 ("ARM: bcm2835: Add names for the Raspberry Pi GPIO lines")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57f718aa4b93392fb1a8c0a874ab882b9e18136a ]
The red LED on the Raspberry Pi 3 B Plus is the power LED.
So fix the GPIO line name accordingly.
Fixes: 71c0cd2283f2 ("ARM: dts: bcm2837: Add Raspberry Pi 3 B+")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd26fd02749ec964eb0d588a3bab9e09bf77927 ]
The GPIOs 46 & 47 are already used for a I2C interface to a SMPS.
So fix the GPIO line names accordingly.
Fixes: a54fe8a6cf66 ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c663e5e5bbf2a5b85e0f76ccb69663f583c3e33 ]
The GPIOs 30 to 39 are connected to the Cypress CYW43438 (Wifi/BT).
So fix the GPIO line names accordingly.
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5c579a34a87117c20b411df583ae816c1ec84f ]
Fix names of extra pingroup node and property for gpio bus recovery.
Without the change i2c2 is not functional.
Fixes: 56f0df6b6b58 ("ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2c")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d397a1277853498e8b7b305f2610881357c033f ]
Commit f3e7dae323ab ("ARM: dts: imx6qdl: add enet_out clk
support") added another item to the list of clocks for the fec
device. As imx6dl-eckelmann-ci4x10.dts only overwrites clocks,
but not clock-names this resulted in an inconsistency with
clocks having one item more than clock-names.
Also overwrite clock-names with the same value as in
imx6qdl.dtsi. This is a no-op today, but prevents similar
inconsistencies if the soc file will be changed in a similar way
in the future.
Signed-off-by: Thorsten Scherer <t.scherer@eckelmann.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f3e7dae323ab ("ARM: dts: imx6qdl: add enet_out clk support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01a850ee61cbf0ab77dcbf26bb133fec2dd640d6 ]
The F1C100 series of SoCs actually have their watchdog IP being
compatible with the newer Allwinner generation, not the older one.
The currently described sun4i-a10-wdt actually does not work, neither
the watchdog functionality (just never fires), nor the reset part
(reboot hangs).
Replace the compatible string with the one used by the newer generation.
Verified to work with both the watchdog and reboot functionality on a
LicheePi Nano.
Also add the missing interrupt line and clock source, to make it binding
compliant.
Fixes: 4ba16d17efdd ("ARM: dts: suniv: add initial DTSI file for F1C100s")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220317162349.739636-4-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 130b5e32ba9d2d2313e39cf3f6d0729bff02b76a ]
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: cru-bus@100: 'pin-controller@1c0' does not match any of the regexes: '^clock-controller@[a-f0-9]+$', '^phy@[a-f0-9]+$', '^pinctrl@[a-f0-9]+$', '^syscon@[a-f0-9]+$', '^thermal@[a-f0-9]+$'
From schema: Documentation/devicetree/bindings/mfd/brcm,cru.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: pin-controller@1c0: $nodename:0: 'pin-controller@1c0' does not match '^(pinctrl|pinmux)(@[0-9a-f]+)?$'
From schema: Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml
Ref: e7391b021e3f ("dt-bindings: mfd: brcm,cru: Rename pinctrl node")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
