IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 5aed5b7c2430ce318a8e62f752f181e66f0d1053 upstream.
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a611bf473d1f77b70f7188b5577542cb39b4701b upstream.
For optimal power consumption of USB4 routers the XHCI PCIe endpoint
used for tunneling must be in D3. Historically this is accomplished
by a long list of PCIe IDs that correspond to these endpoints because
the xhci_hcd driver will not default to allowing runtime PM for all
devices.
As both AMD and Intel have released new products with new XHCI controllers
this list continues to grow. In reviewing the XHCI specification v1.2 on
page 607 there is already a requirement that the PCI power management
states D3hot and D3cold must be supported.
In the quirk list, use this to indicate that runtime PM should be allowed
on XHCI controllers. The following controllers are known to be xHC 1.2 and
dropped explicitly:
* AMD Yellow Carp
* Intel Alder Lake
* Intel Meteor Lake
* Intel Raptor Lake
[keep PCI ID for Alder Lake PCH for recently added quirk -Mathias]
Cc: stable@vger.kernel.org
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-4-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34cd2db408d591bc15771cbcc90939ade0a99a21 upstream.
Systems based on Alder Lake P see significant boot time delay if
boot firmware tries to control usb ports in unexpected link states.
This is seen with self-powered usb devices that survive in U3 link
suspended state over S5.
A more generic solution to power off ports at shutdown was attempted in
commit 83810f84ecf1 ("xhci: turn off port power in shutdown")
but it caused regression.
Add host specific XHCI_RESET_TO_DEFAULT quirk which will reset host and
ports back to default state in shutdown.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-3-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f547472380136718b56064ea5689a61e135f904 upstream.
This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.
ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0
Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3
Cc: stable@vger.kernel.org
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221024142720.4122053-2-mathias.nyman@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb8f60dd1b67520e0e0d7978ef17d015690acfc1 upstream.
When port is connected and then disconnected, the state stays as
configured. Which is incorrect as the port is no longer configured,
but in a not attached state.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/1664997235-18198-1-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 308c316d16cbad99bb834767382baa693ac42169 upstream.
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/ced336c84434571340c07994e3667a0ee284fefe.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f78961f8380b940e0cfc7e549336c21a2ad44f4d upstream.
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable@vger.kernel.org
Reported-by: Jeff Vanhoof <jdv1029@gmail.com>
Reported-by: Dan Vacura <w36195@motorola.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com>
Tested-by: Jeff Vanhoof <jdv1029@gmail.com>
Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b57b08e6f431348363adffa5b6643fe3ec9dc7fe upstream.
In uvc_video_encode_isoc_sg, the uvc_request's sg list is
incorrectly being populated leading to corrupt video being
received by the remote end. When building the sg list the
usage of buf->sg's 'dma_length' field is not correct and
instead its 'length' field should be used.
Fixes: e81e7f9a0eb9 ("usb: gadget: uvc: add scatter gather support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Vanhoof <qjv001@motorola.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-5-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a0a2760b04814428800d48281a447a7522470ad upstream.
If there is a transmission error the buffer will be returned too early,
causing a memory fault as subsequent requests for that buffer are still
queued up to be sent. Refactor the error handling to wait for the final
request to come in before reporting back the buffer to userspace for all
transfer types (bulk/isoc/isoc_sg). This ensures userspace knows if the
frame was successfully sent.
Fixes: e81e7f9a0eb9 ("usb: gadget: uvc: add scatter gather support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20221018215044.765044-4-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aef11279888c00e1841a3533a35d279285af3a51 upstream.
The exit condition to quit iterating over the sg_list, while encoding
the sg entries, has to consider the case that the dma_len of the entry
could be zero. This patch takes this condition to account.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220402232744.3622565-4-m.grzeschik@pengutronix.de
Cc: Dan Vacura <w36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b969f93bcef9b3d9e92f1810e22bbd6c344a0e5 upstream.
On uvc_video_encode_isoc_sg the mapped vb2 buffer is returned
to early. Only after the last usb_request worked with the buffer
it is allowed to give it back to vb2. This patch fixes that.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220402232744.3622565-3-m.grzeschik@pengutronix.de
Cc: Dan Vacura <w36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61aa709ca58a0dbeeb817bfa9230c1a92979f2c6 upstream.
The function uvcg_queue_next_buffer is used different than its name
suggests. The return value nextbuf is never used by any caller. This
patch reworks the function to its actual purpose, by removing the unused
code and renaming it. The function name uvcg_complete_buffer makes it
more clear that it is actually marking the current video buffer as
complete.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20220402232744.3622565-2-m.grzeschik@pengutronix.de
Cc: Dan Vacura <w36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f262ce66d40cc6858d1fcb11e7b7f960448a4f38 upstream.
The function uvc_video_encode_header function returns the number of
bytes used for the header. We change the video_encode_isoc_sg function
to use the returned header_len rather than UVCG_REQUEST_HEADER_LEN and
make the encode function more flexible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20211022093223.26493-1-m.grzeschik@pengutronix.de
Cc: Dan Vacura <w36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 859c675d84d488e2f9b515c713ea890c9f045f0c upstream.
The uvc request headerlen of 2 was defined as UVCG_REQUEST_HEADER_LEN
in commit e81e7f9a0eb9 ("usb: gadget: uvc: add scatter gather support").
We missed to use it consistently. This patch fixes that.
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20211018072059.11465-1-m.grzeschik@pengutronix.de
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Dan Vacura <w36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bce2b0539933e485d22d6f6f076c0fcd6f185c4c ]
In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.
Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.
Note that this is found by KMSAN, so only kernel compilation
is tested.
Reported-by: syzbot+79832d33eb89fb3cd092@syzkaller.appspotmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220922134847.1101921-1-dzm91@hust.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad5dbfc123e6ffbbde194e2a4603323e09f741ee ]
This reverts commit 86d92f5465958752481269348d474414dccb1552,
which fix the timeout issue for "Samsung Fit Flash".
But the commit affects not only "Samsung Fit Flash" but also other usb
storages that use the same controller and causes severe performance
regression.
# hdparm -t /dev/sda (without the quirk)
Timing buffered disk reads: 622 MB in 3.01 seconds = 206.66 MB/sec
# hdparm -t /dev/sda (with the quirk)
Timing buffered disk reads: 220 MB in 3.00 seconds = 73.32 MB/sec
The commit author mentioned that "Issue was reproduced after device has
bad block", so this quirk should be applied when we have the timeout
issue with a device that has bad blocks.
We revert the commit so that we apply this quirk by adding kernel
paramters using a bootloader or other ways when we really need it,
without the performance regression with devices that don't have the
issue.
Signed-off-by: sunghwan jung <onenowy@gmail.com>
Link: https://lore.kernel.org/r/20220913114913.3073-1-onenowy@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63d7f9810a38102cdb8cad214fac98682081e1a7 ]
When configured in HOST mode, after issuing U3/L2 exit controller fails
to send proper CRC checksum in CRC5 field. Because of this behavior
Transaction Error is generated, resulting in reset and re-enumeration of
usb device attached. Enabling chicken bit 10 of GUCTL1 will correct this
problem.
When this bit is set to '1', the UTMI/ULPI opmode will be changed to
"normal" along with HS terminations, term, and xcvr signals after EOR.
This option is to support certain legacy UTMI/ULPI PHYs.
Added "snps,resume-hs-terminations" quirk to resolved the above issue.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220920052235.194272-3-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eea4c860c3b366369eff0489d94ee4f0571d467d ]
The usb function device call musb_gadget_queue() adds the passed
request to musb_ep::req_list,If the (request->length > musb_ep->packet_sz)
and (is_buffer_mapped(req) return false),the rxstate() will copy all data
in fifo to request->buf which may cause request->buf out of bounds.
Fix it by add the length check :
fifocnt = min_t(unsigned, request->length - request->actual, fifocnt);
Signed-off-by: Robin Guo <guoweibin@inspur.com>
Link: https://lore.kernel.org/r/20220906102119.1b071d07a8391ff115e6d1ef@inspur.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e271f42a5cc3768cd2622b929ba66859ae21f97 ]
xhci_alloc_stream_info() allocates stream context array for stream_info
->stream_ctx_array with xhci_alloc_stream_ctx(). When some error occurs,
stream_info->stream_ctx_array is not released, which will lead to a
memory leak.
We can fix it by releasing the stream_info->stream_ctx_array with
xhci_free_stream_ctx() on the error path to avoid the potential memory
leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c69400b09e471a3f1167adead55a808f0da6534a ]
The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-3-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bd954c56197caf5e3a804d989094bc3fe6329aa ]
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Link: https://lore.kernel.org/r/1660170455-15781-2-git-send-email-justinpopo6@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c703e29da5efac6180e4c189029fa34b7e48e97 ]
When the dr_mode is "host", after the host enter runtime suspend,
the mtu3 can't do it, because the mtu3's device wakeup function is
not enabled, instead it's enabled in gadget init function, to fix
the issue, init wakeup early in mtu3's probe()
Fixes: 6b587394c65c ("usb: mtu3: support suspend/resume for dual-role mode")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reported-by: Tianping Fang <tianping.fang@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220929064459.32522-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24b7ba2f88e04800b54d462f376512e8c41b8a3c ]
When opts->pnp_string is changed with configfs, new memory is allocated for
the string. It does not, however, update dev->pnp_string, even though the
memory is freed. When rquesting the string, the host then gets old or
corrupted data rather than the new string. The ieee 1284 id string should
be allowed to change while the device is connected.
The bug was introduced in commit fdc01cc286be ("usb: gadget: printer:
Remove pnp_string static buffer"), which changed opts->pnp_string from a
char[] to a char*.
This patch changes dev->pnp_string from a char* to a char** pointing to
opts->pnp_string.
Fixes: fdc01cc286be ("usb: gadget: printer: Remove pnp_string static buffer")
Signed-off-by: Albert Briscoe <albertsbriscoe@gmail.com>
Link: https://lore.kernel.org/r/20220911223753.20417-1-albertsbriscoe@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 484d6f7aa3283d082c87654b7fe7a7f725423dfb ]
commit 8b328f8002bc ("xhci: re-initialize the HC during resume if HCE was
set") introduced a new warning message when the host controller error
was set and re-initializing.
This is expected behavior on some designs which already set
`xhci->broken_suspend` so the new warning is alarming to some users.
Modify the code to only show the warning if this was a surprising behavior
to the XHCI driver.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216470
Fixes: 8b328f8002bc ("xhci: re-initialize the HC during resume if HCE was set")
Reported-by: Artem S. Tashkinov <aros@gmx.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6155eaf6b05e558218b44b88a6cad03f15a586c ]
Previously usb_decode_ctrl() only decodes standard control requests, but
it was used for non-standard requests also. If it's non-standard or
unknown standard bRequest, print the Setup data values.
Fixes: af32423a2d86 ("usb: dwc3: trace: decode ctrl request")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/8d6a30f2f2f953eff833a5bc5aac640a4cc2fc9f.1658971571.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 37d49519b41405b08748392c6a7f193d9f77ecd2 upstream.
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
These hubs suffer from two separate problems:
1) After the host system was suspended and woken up, the hubs appear to
be in a random state. Some downstream ports (both internal to the
built-in audio and network controllers, and external to USB sockets)
may no longer be functional. The exact list of disabled ports (if
any) changes from wakeup to wakeup. Ports remain in that state until
the dock is power-cycled, or until the laptop is rebooted.
Wakeup sources connected to the hubs (keyboard, WoL on the integrated
gigabit controller) will wake the system up from suspend, but they
may no longer work after wakeup (and in that case will no longer work
as wakeup source in a subsequent suspend-wakeup cycle).
This issue appears in the logs with messages such as:
usb 1-6.1-port4: cannot disable (err = -71)
usb 1-6-port2: cannot disable (err = -71)
usb 1-6.1: clear tt 1 (80c0) error -71
usb 1-6-port4: cannot disable (err = -71)
usb 1-6.4: PM: dpm_run_callback(): usb_dev_resume+0x0/0x10 [usbcore] returns -71
usb 1-6.4: PM: failed to resume async: error -71
usb 1-7: reset full-speed USB device number 5 using xhci_hcd
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: cannot reset (err = -71)
usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
usb 1-6.1-port1: cannot disable (err = -71)
2) Some USB devices cannot be enumerated properly. So far I have only
seen the issue with USB 3.0 devices. The same devices work without
problem directly connected to the host system, to other systems or to
other hubs (even when those hubs are connected to the OneLink+ dock).
One very reliable reproducer is this USB 3.0 HDD enclosure:
152d:9561 JMicron Technology Corp. / JMicron USA Technology Corp. Mobius
I have seen it happen sporadically with other USB 3.0 enclosures,
with controllers from different manufacturers, all self-powered.
Typical messages in the logs:
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 6, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 7, error -62
usb 2-1-port4: attempt power cycle
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 8, error -62
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
usb 2-1.4: device not accepting address 9, error -62
usb 2-1-port4: unable to enumerate USB device
Through trial and error, I found that the USB_QUIRK_RESET_RESUME solved
the second issue. Further testing then uncovered the first issue. Test
results are summarized in this table:
=======================================================================================
Settings USB2 hotplug USB3 hotplug State after waking up
---------------------------------------------------------------------------------------
power/control=auto works fails broken
usbcore.autosuspend=-1 works works broken
OR power/control=on
power/control=auto works (1) works (1) works
and USB_QUIRK_RESET_RESUME
power/control=on works works works
and USB_QUIRK_RESET_RESUME
HUB_QUIRK_DISABLE_AUTOSUSPEND works works works
and USB_QUIRK_RESET_RESUME
=======================================================================================
In those results, the power/control settings are applied to both hubs,
both on the USB2 and USB3 side, before each test.
From those results, USB_QUIRK_RESET_RESUME is required to reset the hubs
properly after a suspend-wakeup cycle, and the hubs must not autosuspend
to work around the USB3 issue.
A secondary effect of USB_QUIRK_RESET_RESUME is to prevent the hubs'
upstream links from suspending (the downstream ports can still suspend).
This secondary effect is used in results (1). It is enough to solve the
USB3 problem.
Setting USB_QUIRK_RESET_RESUME on those hubs is the smallest patch that
solves both issues.
Prior to creating this patch, I have used the USB_QUIRK_RESET_RESUME via
the kernel command line for over a year without noticing any side
effect.
Thanks to Oliver Neukum @Suse for explanations of the operations of
USB_QUIRK_RESET_RESUME, and requesting more testing.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220927073407.5672-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d591b32e519603524a35b172156db71df9116902 upstream.
If DbC is already in use, then the allocated memory for the xhci_dbc struct
doesn't get freed before returning NULL, which leads to a memleak.
Fixes: 534675942e90 ("xhci: dbc: refactor xhci_dbc_init()")
Cc: stable@vger.kernel.org
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220921123450.671459-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7bd7ad3c310cd6766f170927381eea0aa6f46c69 upstream.
The 300 bps rate of SIO devices has been mapped to 9600 bps since
2003... Let's fix the regression.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a659daf63d16aa883be42f3f34ff84235c302198 upstream.
Syzbot found an issue in usbmon module, where the user space client can
corrupt the monitor's internal memory, causing the usbmon module to
crash the kernel with segfault, UAF, etc.
The reproducer mmaps the /dev/usbmon memory to user space, and
overwrites it with arbitrary data, which causes all kinds of issues.
Return an -EPERM error from mon_bin_mmap() if the flag VM_WRTIE is set.
Also clear VM_MAYWRITE to make it impossible to change it to writable
later.
Cc: "Dmitry Vyukov" <dvyukov@google.com>
Cc: stable <stable@kernel.org>
Fixes: 6f23ee1fefdc ("USB: add binary API to usbmon")
Suggested-by: PaX Team <pageexec@freemail.hu> # for the VM_MAYRITE portion
Link: https://syzkaller.appspot.com/bug?id=2eb1f35d6525fa4a74d75b4244971e5b1411c95a
Reported-by: syzbot+23f57c5ae902429285d7@syzkaller.appspotmail.com
Signed-off-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Link: https://lore.kernel.org/r/20220919215957.205681-1-tadeusz.struk@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415ba26cb73f7d22a892043301b91b57ae54db02 upstream.
Sink only devices do not have any source capabilities, so
the driver should not warn about that. Also DRP (Dual Role
Power) capable devices, such as USB Type-C docking stations,
do not return any source capabilities unless they are
plugged to a power supply themselves.
Fixes: 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922145924.80667-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e00b488e813f0f1ad9f778e771b7cd2fe2877023 upstream.
The UAS mode of Hiksemi USB_HDD is reported to fail to work on several
platforms with the following error message, then after re-connecting the
device will be offlined and not working at all.
[ 592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
inflight: CMD
[ 592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
04 00 00
[ 592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
inflight: CMD
[ 592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
00 08 00
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901185-21067-1-git-send-email-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a625a4b8806cc1e928b7dd2cca1fee709c9de56e upstream.
The UAS mode of Hiksemi is reported to fail to work on several platforms
with the following error message, then after re-connecting the device will
be offlined and not working at all.
[ 592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
inflight: CMD
[ 592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
04 00 00
[ 592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
inflight: CMD
[ 592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
00 08 00
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901173-21020-1-git-send-email-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91062e663b261815573ce00967b1895a99e668df upstream.
On some DWC3 controllers (e.g. Rockchip SoCs), the DWC3 core
doesn't support 64-bit DMA address width. In this case, this
driver should use the default 32-bit mask. Otherwise, the DWC3
controller will break if it runs on above 4GB physical memory
environment.
This patch reads the DWC_USB3_AWIDTH bits of GHWPARAMS0 which
used for the DMA address width, and only configure 64-bit DMA
mask if the DWC_USB3_AWIDTH is 64.
Fixes: 45d39448b4d0 ("usb: dwc3: support 64 bit DMA in platform driver")
Cc: stable <stable@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Link: https://lore.kernel.org/r/20220901083446.3799754-1-william.wu@rock-chips.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe0a2ac7c627b064c479ad0c3b25e531d342e048 ]
This reverts commit 8cb339f1c1f04baede9d54c1e40ac96247a6393b as it
throws up a bunch of sparse warnings as reported by the kernel test
robot.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202209020044.CX2PfZzM-lkp@intel.com
Fixes: 8cb339f1c1f0 ("usb: gadget: udc-xilinx: replace memcpy with memcpy_toio")
Cc: stable@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58bfe7d8e31014d7ce246788df99c56e3cfe6c68 ]
This reverts commit 3d5f70949f1b1168fbb17d06eb5c57e984c56c58.
The quirk does not work properly, more work is needed to determine what
should be done here.
Reported-by: Oliver Neukum <oneukum@suse.com>
Cc: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Fixes: 3d5f70949f1b ("usb: add quirks for Lenovo OneLink+ Dock")
Link: https://lore.kernel.org/r/9a17ea86-079f-510d-e919-01bc53a6d09f@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d5f70949f1b1168fbb17d06eb5c57e984c56c58 ]
The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream
Those two controllers both have problems with some USB3.0 devices,
particularly self-powered ones. Typical error messages include:
Timeout while waiting for setup device command
device not accepting address X, error -62
unable to enumerate USB device
By process of elimination the controllers themselves were identified as
the cause of the problem. Through trial and error the issue was solved
by using USB_QUIRK_RESET_RESUME for both chips.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220824191320.17883-1-jflf_kernel@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 040f2dbd2010c43f33ad27249e6dac48456f4d99 ]
Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions. If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop. Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.
This patch depends on
commit 69e131d1ac4e ("usb: dwc3: gadget: Prevent repeat pullup()")
Fixes: 77adb8bdf422 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f8034f493b5eb1ad21ff392fd30c0cf9e71f73f ]
If the GEVNTCOUNT indicates events in the event buffer, the driver needs
to acknowledge them before the controller can halt. Simply let the
interrupt handler acknowledges the remaining event generated by the
controller while polling for DSTS.DEVCTLHLT. This avoids disabling irq
and taking care of race condition between the interrupt handlers and
pullup().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/ea306ec93c41ccafbdb5d16404ff3b6eca299613.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69e131d1ac4e52a59ec181ab4f8aa8c48cd8fb64 ]
Don't do soft-disconnect if it's previously done. Likewise, don't do
soft-connect if the device is currently connected and running. It would
break normal operation.
Currently the caller of pullup() (udc's sysfs soft_connect) only checks
if it had initiated disconnect to prevent repeating soft-disconnect. It
doesn't check for soft-connect. To be safe, let's keep the check here
regardless whether the udc core is fixed.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1c1345bd66c97a9d32f77d63aaadd04b7b037143.1650593829.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0066472de157439d58454f4a55786f1045ea5681 ]
It is recommended by the Synopsis databook to issue a DCTL.CSftReset
when reconnecting from a device-initiated disconnect routine. This
resolves issues with enumeration during fast composition switching
cases, which result in an unknown device on the host.
Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220316011358.3057-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8217f07a50236779880f13e87f99224cd9117f83 ]
There is a race present where the DWC3 runtime resume runs in parallel
to the UDC unbind sequence. This will eventually lead to a possible
scenario where we are enabling the run/stop bit, without a valid
composition defined.
Thread#1 (handling UDC unbind):
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
--> continue UDC unbind sequence
-->Thread#2 is running in parallel here
Thread#2 (handing next cable connect)
__dwc3_set_mode()
-->pm_runtime_get_sync()
-->dwc3_gadget_resume()
-->dwc->gadget_driver is NOT NULL yet
-->dwc3_gadget_run_stop(1)
--> _dwc3gadget_start()
...
Fix this by tracking the pullup disable routine, and avoiding resuming
of the DWC3 gadget. Once the UDC is re-binded, that will trigger the
pullup enable routine, which would handle enabling the DWC3 gadget.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/20210917021852.2037-1-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 040f2dbd2010 ("usb: dwc3: gadget: Avoid duplicate requests to enable Run/Stop")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f511aef2ebe5377d4c263842f2e0c0b8e274e8e5 upstream.
On page 362 of the USB3.2 specification (
https://usb.org/sites/default/files/usb_32_20210125.zip),
The 'SuperSpeed Endpoint Companion Descriptor' shall only be returned
by Enhanced SuperSpeed devices that are operating at Gen X speed.
Each endpoint described in an interface is followed by a 'SuperSpeed
Endpoint Companion Descriptor'.
If users use SuperSpeed UDC, host can't recognize the device if endpoint
doesn't have 'SuperSpeed Endpoint Companion Descriptor' followed.
Currently in the uac2 driver code:
1. ss_epout_desc_comp follows ss_epout_desc;
2. ss_epin_fback_desc_comp follows ss_epin_fback_desc;
3. ss_epin_desc_comp follows ss_epin_desc;
4. Only ss_ep_int_desc endpoint doesn't have 'SuperSpeed Endpoint
Companion Descriptor' followed, so we should add it.
Fixes: eaf6cbe09920 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Link: https://lore.kernel.org/r/20220721014815.14453-1-quic_jackp@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
