IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 28f091bc2f8c23b7eac2402956b692621be7f9f4 upstream.
Initialize the mask for PKU permissions as if CR4.PKE=0, avoiding
incorrect interpretations of the nested hypervisor's page tables.
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53b7ca1a359389276c76fbc9e1009d8626a17e40 upstream.
Currently, checks for whether VT-d PI can be used refer to the current
status of the feature in the current vCPU; or they more or less pick
vCPU 0 in case a specific vCPU is not available.
However, these checks do not attempt to synchronize with changes to
the IRTE. In particular, there is no path that updates the IRTE when
APICv is re-activated on vCPU 0; and there is no path to wakeup a CPU
that has APICv disabled, if the wakeup occurs because of an IRTE
that points to a posted interrupt.
To fix this, always go through the VT-d PI path as long as there are
assigned devices and APICv is available on both the host and the VM side.
Since the relevant condition was copied over three times, take the hint
and factor it into a separate function.
Suggested-by: Sean Christopherson <seanjc@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Message-Id: <20211123004311.2954158-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e1901f6c86c896acff6609e0176f93f756d8b2a upstream.
If APICv is disabled for this vCPU, assigned devices may still attempt to
post interrupts. In that case, we need to cancel the vmentry and deliver
the interrupt with KVM_REQ_EVENT. Extend the existing code that handles
injection of L1 interrupts into L2 to cover this case as well.
vmx_hwapic_irr_update is only called when APICv is active so it would be
confusing to add a check for vcpu->arch.apicv_active in there. Instead,
just use vmx_set_rvi directly in vmx_sync_pir_to_irr.
Cc: stable@vger.kernel.org
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211123004311.2954158-3-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40e5f9080472b614eeedcc5ba678289cd98d70df upstream.
Like KVM_REQ_TLB_FLUSH_CURRENT, the GUEST variant needs to be serviced at
nested transitions, as KVM doesn't track requests for L1 vs L2. E.g. if
there's a pending flush when a nested VM-Exit occurs, then the flush was
requested in the context of L2 and needs to be handled before switching
to L1, otherwise the flush for L2 would effectiely be lost.
Opportunistically add a helper to handle CURRENT and GUEST as a pair, the
logic for when they need to be serviced is identical as both requests are
tied to L1 vs. L2, the only difference is the scope of the flush.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e34 ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b4a5a5d56881ece3c66b9a9a8943a6f41bd7349 upstream.
Flush the current VPID when handling KVM_REQ_TLB_FLUSH_GUEST instead of
always flushing vpid01. Any TLB flush that is triggered when L2 is
active is scoped to L2's VPID (if it has one), e.g. if L2 toggles CR4.PGE
and L1 doesn't intercept PGE writes, then KVM's emulation of the TLB
flush needs to be applied to L2's VPID.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 07ffaf343e34 ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 712494de96f35f3e146b36b752c2afe0fdc0f0cc upstream.
Fully emulate a guest TLB flush on nested VM-Enter which changes vpid12,
i.e. L2's VPID, instead of simply doing INVVPID to flush real hardware's
TLB entries for vpid02. From L1's perspective, changing L2's VPID is
effectively a TLB flush unless "hardware" has previously cached entries
for the new vpid12. Because KVM tracks only a single vpid12, KVM doesn't
know if the new vpid12 has been used in the past and so must treat it as
a brand new, never been used VPID, i.e. must assume that the new vpid12
represents a TLB flush from L1's perspective.
For example, if L1 and L2 share a CR3, the first VM-Enter to L2 (with a
VPID) is effectively a TLB flush as hardware/KVM has never seen vpid12
and thus can't have cached entries in the TLB for vpid12.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com>
Fixes: 5c614b3583e7 ("KVM: nVMX: nested VPID emulation")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78311a514099932cd8434d5d2194aa94e56ab67c upstream.
Synchronize the two calls to kvm_x86_sync_pir_to_irr. The one
in the reenter-guest fast path invoked the callback unconditionally
even if LAPIC is present but disabled. In this case, there are
no interrupts to deliver, and therefore posted interrupts can
be ignored.
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bda44d844758c70c8dc1478e6fc9c25efa90c5a7 upstream.
When modifying memslots, snapshot the "old" memslot and copy it to the
"new" memslot's arch data after (re)acquiring slots_arch_lock. x86 can
change a memslot's arch data while memslot updates are in-progress so
long as it holds slots_arch_lock, thus snapshotting a memslot without
holding the lock can result in the consumption of stale data.
Fixes: b10a038e84d1 ("KVM: mmu: Add slots_arch_lock for memslot arch fields")
Cc: stable@vger.kernel.org
Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211104002531.1176691-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 574c3c55e969096cea770eda3375ff35ccf91702 upstream.
When recursively clearing out disconnected pts, the range based TLB
flush in handle_removed_tdp_mmu_page uses the wrong starting GFN,
resulting in the flush mostly missing the affected range. Fix this by
using base_gfn for the flush.
In response to feedback from David Matlack on the RFC version of this
patch, also move a few definitions into the for loop in the function to
prevent unintended references to them in the future.
Fixes: a066e61f13cf ("KVM: x86/mmu: Factor out handling of removed page tables")
CC: stable@vger.kernel.org
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20211115211704.2621644-1-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b285a5587506bae084cf9a3ed5aa491d623b91b upstream.
Reject userspace memslots whose size exceeds the storage capacity of an
"unsigned long". KVM's uAPI takes the size as u64 to support large slots
on 64-bit hosts, but does not account for the size being truncated on
32-bit hosts in various flows. The access_ok() check on the userspace
virtual address in particular casts the size to "unsigned long" and will
check the wrong number of bytes.
KVM doesn't actually support slots whose size doesn't fit in an "unsigned
long", e.g. KVM's internal kvm_memory_slot.npages is an "unsigned long",
not a "u64", and misc arch specific code follows that behavior.
Fixes: fa3d315a4ce2 ("KVM: Validate userspace_addr of memslot when registered")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <20211104002531.1176691-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7cfc5c653b07782e7059527df8dc1e3143a7591e upstream.
avic_set_running() passes the current CPU to avic_vcpu_load(), albeit
via vcpu->cpu rather than smp_processor_id(). If the thread is migrated
while avic_set_running runs, the call to avic_vcpu_load() can use a stale
value for the processor id. Avoid this by blocking preemption over the
entire execution of avic_set_running().
Reported-by: Sean Christopherson <seanjc@google.com>
Fixes: 8221c1370056 ("svm: Manage vcpu load/unload when enable AVIC")
Cc: stable@vger.kernel.org
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a44f42ba7f1ad7d3c17bc7d91013fe814a53c5dc upstream.
While working on supporting the Intel HDR backlight interface, I noticed
that there's a couple of laptops that will very rarely manage to boot up
without detecting Intel HDR backlight support - even though it's supported
on the system. One example of such a laptop is the Lenovo P17 1st
generation.
Following some investigation Ville Syrjälä did through the docs they have
available to them, they discovered that there's actually supposed to be a
30ms wait after writing the source OUI before we begin setting up the rest
of the backlight interface.
This seems to be correct, as adding this 30ms delay seems to have
completely fixed the probing issues I was previously seeing. So - let's
start performing a 30ms wait after writing the OUI, which we do in a manner
similar to how we keep track of PPS delays (e.g. record the timestamp of
the OUI write, and then wait for however many ms are left since that
timestamp right before we interact with the backlight) in order to avoid
waiting any longer then we need to. As well, this also avoids us performing
this delay on systems where we don't end up using the HDR backlight
interface.
V3:
* Move last_oui_write into intel_dp
V2:
* Move panel delays into intel_pps
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 4a8d79901d5b ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211130212912.212044-1-lyude@redhat.com
(cherry picked from commit c7c90b0b8418a97d3aa8b39aae1992908948efad)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94ebc035456a4ccacfbbef60c444079a256623ad upstream.
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdef485217d30382f3bf6448c54b4401648fe3f1 upstream.
The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.
After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c41753 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").
The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.
How to reproduce:
- Add the following nftables rule to a prerouting chain:
meta nfproto ipv6 fib saddr . mark . iif oif missing drop
This can be done with:
sudo nft create table inet test
sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
- Run:
sudo ip -6 rule add table main suppress_prefixlength 0
- Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
with every incoming ipv6 packet.
This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.
[1]: ca7a03c417/net/ipv6/fib6_rules.c (L71)
[2]: ca7a03c417/net/ipv6/fib6_rules.c (L99)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105
Fixes: ca7a03c41753 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dc9fb47bc9a95f1cc6c5655341860c5e50f91d4 upstream.
Add PCI ID and callbacks to support Intel Alder Lake.
Link: https://lore.kernel.org/r/20211124204218.1784559-1-adrian.hunter@intel.com
Cc: stable@vger.kernel.org # v5.15+
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0956ba63bd94355bf38cd40f7eb9104577739ab8 upstream.
A commit introduced formal regstration of all Fabric nodes to the SCSI
transport as well as REG/UNREG RPI mailbox requests. The commit introduced
the NLP_RELEASE_RPI flag for rports set in the lpfc_cmpl_els_logo_acc()
routine to help clean up the RPIs. This new code caused the driver to
release the RPI value used for the remote port and marked the RPI invalid.
When the driver later attempted to re-login, it would use the invalid RPI
and the adapter rejected the PLOGI request. As no login occurred, the
devloss timer on the rport expired and connectivity was lost.
This patch corrects the code by removing the snippet that requests the rpi
to be unregistered. This change only occurs on a node that is already
marked to be rediscovered. This puts the code back to its original
behavior, preserving the already-assigned rpi value (registered or not)
which can be used on the re-login attempts.
Link: https://lore.kernel.org/r/20211123165646.62740-1-jsmart2021@gmail.com
Fixes: fe83e3b9b422 ("scsi: lpfc: Fix node handling for Fabric Controller and Domain Controller")
Cc: <stable@vger.kernel.org> # v5.14+
Co-developed-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: Paul Ely <paul.ely@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f48394cf1f3e8486591ad98c11cdadb8f1ef2ad upstream.
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c8ad7e8cf29eb55836e7a0215f967746ab2b504 upstream.
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
driver_detach
device_release_driver_internal
__device_release_driver
drv->remove(dev) --> platform_drv_remove/platform_remove
drv->remove(dev) --> sata_fsl_remove
iounmap(host_priv->hcr_base); <---- unmap
kfree(host_priv); <---- free
devres_release_all
release_nodes
dr->node.release(dev, dr->data) --> ata_host_stop
ap->ops->port_stop(ap) --> sata_fsl_port_stop
ioread32(hcr_base + HCONTROL) <---- UAF
host->ops->host_stop(host)
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 054aa8d439b9185d4f5eb9a90282d1ce74772969 upstream.
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52d04d408185b7aa47628d2339c28ec70074e0ae upstream.
When running without MIO support, with pci=nomio or for devices which
are not MIO-capable the zPCI subsystem generates pseudo-MMIO addresses
to allow access to PCI BARs via MMIO based Linux APIs even though the
platform uses function handles and BAR numbers.
This is done by stashing an index into our global IOMAP array which
contains the function handle in the 16 most significant bits of the
addresses returned by ioremap() always setting the most significant bit.
On the other hand the MIO addresses assigned by the platform for use,
while requiring special instructions, allow PCI access with virtually
mapped physical addresses. Now the problem is that these MIO addresses
and our own pseudo-MMIO addresses may overlap, while functionally this
would not be a problem by itself this overlap is detected by common code
as both address types are added as resources in the iomem_resource tree.
This leads to the overlapping resource claim of either the MIO capable
or non-MIO capable devices with being rejected.
Since PCI is tightly coupled to the use of the iomem_resource tree, see
for example the code for request_mem_region(), we can't reasonably get
rid of the overlap being detected by keeping our pseudo-MMIO addresses
out of the iomem_resource tree.
Instead let's move the range used by our own pseudo-MMIO addresses by
starting at (1UL << 62) and only using addresses below (1UL << 63) thus
avoiding the range currently used for MIO addresses.
Fixes: c7ff0e918a7c ("s390/pci: deal with devices that have no support for MIO instructions")
Cc: stable@vger.kernel.org # 5.3+
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 679d94cd7d900871e5bc9cf780bd5b73af35ab42 upstream.
For previous version, it uses 'sg_table.nent's to traverse sg_table in pages
free flow.
However, 'sg_table.nents' is reassigned in 'dma_map_sg', it means the number of
created entries in the DMA adderess space.
So, use 'sg_table.nents' in pages free flow will case some pages can't be freed.
Here we should use sg_table.orig_nents to free pages memory, but use the
sgtable helper 'for each_sgtable_sg'(, instead of the previous rather common
helper 'for_each_sg' which maybe cause memory leak) is much better.
Fixes: d963ab0f15fb0 ("dma-buf: system_heap: Allocate higher order pages if available")
Signed-off-by: Guangming <Guangming.Cao@mediatek.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: <stable@vger.kernel.org> # 5.11.*
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211126074904.88388-1-guangming.cao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5283dd677e52af9db6fe6ad11b2f12220d519d0c upstream.
In some very rare cases the init flow may fail. In many cases, this is
recoverable, so we can retry. Implement a loop to retry two more times
after the first attempt failed.
This can happen in two different situations, namely during probe and
during mac80211 start. For the first case, a simple loop is enough.
For the second case, we need to add a flag to prevent mac80211 from
trying to restart it as well, leaving full control with the driver.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20211110150132.57514296ecab.I52a0411774b700bdc7dedb124d8b59bf99456eb2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2c1b5a84669d2477d8fffe9136e86a2cff591729 upstream.
When I hot added a CPU, I found 'cpufreq' directory was not created
below /sys/devices/system/cpu/cpuX/.
It is because get_cpu_device() failed in add_cpu_dev_symlink().
cpufreq_add_dev() is the .add_dev callback of a CPU subsys interface.
It will be called when the CPU device registered into the system.
The call chain is as follows:
register_cpu()
->device_register()
->device_add()
->bus_probe_device()
->cpufreq_add_dev()
But only after the CPU device has been registered, we can get the
CPU device by get_cpu_device(), otherwise it will return NULL.
Since we already have the CPU device in cpufreq_add_dev(), pass
it to add_cpu_dev_symlink().
I noticed that the 'kobj' of the CPU device has been added into
the system before cpufreq_add_dev().
Fixes: 2f0ba790df51 ("cpufreq: Fix creation of symbolic links to policy directories")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d49eb91e86e8c1c1614c72e3e958b6b7e2472a9 upstream.
Currently when removing an ipmi_user the removal is deferred as a work on
the system's workqueue. Although this guarantees the free operation will
occur in non atomic context, it can race with the ipmi_msghandler module
removal (see [1]) . In case a remove_user work is scheduled for removal
and shortly after ipmi_msghandler module is removed we can end up in a
situation where the module is removed fist and when the work is executed
the system crashes with :
BUG: unable to handle page fault for address: ffffffffc05c3450
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
because the pages of the module are gone. In cleanup_ipmi() there is no
easy way to detect if there are any pending works to flush them before
removing the module. This patch creates a separate workqueue and schedules
the remove_work works on it. When removing the module the workqueue is
drained when destroyed to avoid the race.
[1] https://bugs.launchpad.net/bugs/1950666
Cc: stable@vger.kernel.org # 5.1
Fixes: 3b9a907223d7 (ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier)
Signed-off-by: Ioanna Alifieraki <ioanna-maria.alifieraki@canonical.com>
Message-Id: <20211115131645.25116-1-ioanna-maria.alifieraki@canonical.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed53ae75693096f1c10b4561edd31a07b631bd72 upstream.
As reported by Exuvo is possible that we have lot's of EPROTO errors
during device start i.e. firmware load. But after that device works
correctly. Hence marking device gone by few EPROTO errors done by
commit e383c70474db ("rt2x00: check number of EPROTO errors") caused
regression - Exuvo device stop working after kernel update. To fix
disable the check during device start.
Link: https://lore.kernel.org/linux-wireless/bff7d309-a816-6a75-51b6-5928ef4f7a8c@exuvo.se/
Reported-and-tested-by: Exuvo <exuvo@exuvo.se>
Fixes: e383c70474db ("rt2x00: check number of EPROTO errors")
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111141003.GA134627@wp.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65cc4ad62a9ed47c0b4fcd7af667d97d7c29f19d upstream.
For cs8409, it is required to run Jack Detect on resume.
Jack Detect on cs8409+cs42l42 requires an interrupt from
cs42l42 to be sent to cs8409 which is propogated to the driver
via an unsolicited event.
However, the hda_codec drops unsolicited events if the power_state
is not set to PMSG_ON. Which is set at the end of the resume call.
This means there is a race condition between setting power_state
to PMSG_ON and receiving the interrupt.
To solve this, we can add an API to set the power_state earlier
and call that before we start Jack Detect.
This does not cause issues, since we know inside our driver that
we are already initialized, and ready to handle the unsolicited
events.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v5.15+
Link: https://lore.kernel.org/r/20211128115558.71683-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bbfa44116689469267f1a6e3d233b52114139d2 upstream.
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
Link: https://lkml.kernel.org/r/163836995040.432120.10322772773821182925.stgit@devnote2
Cc: stable@vger.kernel.org
Fixes: f47cd9b553aa ("kprobes: kretprobe user entry-handler")
Reported-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee201011c1e1563c114a55c86eb164b236f18e84 upstream.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Fixes: 35402e313663 ("net: Add IPv6 support to VRF device")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5961060692f8b17cd2080620a3d27b95d2ae05ca upstream.
When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes: f295b3ae9f59 ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9380df851878cee71df5a1c7611584421527f7e ]
The commit ddfd9dcf270c ("ACPI: PM: Add acpi_[un]register_wakeup_handler()")
added new functions for drivers to use during the s2idle wakeup path, but
didn't add stubs for when CONFIG_ACPI wasn't set.
Add those stubs in for other drivers to be able to use.
Fixes: ddfd9dcf270c ("ACPI: PM: Add acpi_[un]register_wakeup_handler()")
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20211101014853.6177-1-mario.limonciello@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a61432dc81375be06b02f0061247d3efbdfce3a ]
Possible recursive locking is detected by lockdep when SMC
falls back to TCP. The corresponding warnings are as follows:
============================================
WARNING: possible recursive locking detected
5.16.0-rc1+ #18 Tainted: G E
--------------------------------------------
wrk/1391 is trying to acquire lock:
ffff975246c8e7d8 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0x109/0x250 [smc]
but task is already holding lock:
ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&ei->socket.wq.wait);
lock(&ei->socket.wq.wait);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by wrk/1391:
#0: ffff975246040130 (sk_lock-AF_SMC){+.+.}-{0:0}, at: smc_connect+0x43/0x150 [smc]
#1: ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
stack backtrace:
Call Trace:
<TASK>
dump_stack_lvl+0x56/0x7b
__lock_acquire+0x951/0x11f0
lock_acquire+0x27a/0x320
? smc_switch_to_fallback+0x109/0x250 [smc]
? smc_switch_to_fallback+0xfe/0x250 [smc]
_raw_spin_lock_irq+0x3b/0x80
? smc_switch_to_fallback+0x109/0x250 [smc]
smc_switch_to_fallback+0x109/0x250 [smc]
smc_connect_fallback+0xe/0x30 [smc]
__smc_connect+0xcf/0x1090 [smc]
? mark_held_locks+0x61/0x80
? __local_bh_enable_ip+0x77/0xe0
? lockdep_hardirqs_on+0xbf/0x130
? smc_connect+0x12a/0x150 [smc]
smc_connect+0x12a/0x150 [smc]
__sys_connect+0x8a/0xc0
? syscall_enter_from_user_mode+0x20/0x70
__x64_sys_connect+0x16/0x20
do_syscall_64+0x34/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The nested locking in smc_switch_to_fallback() is considered to
possibly cause a deadlock because smc_wait->lock and clc_wait->lock
are the same type of lock. But actually it is safe so far since
there is no other place trying to obtain smc_wait->lock when
clc_wait->lock is held. So the patch replaces spin_lock() with
spin_lock_nested() to avoid false report by lockdep.
Link: https://lkml.org/lkml/2021/11/19/962
Fixes: 2153bd1e3d3d ("Transfer remaining wait queue entries during fallback")
Reported-by: syzbot+e979d3597f48262cb4ee@syzkaller.appspotmail.com
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ef75e9bd2c998f1c6f6f23a3744136105ddefd5 ]
If trace_seq becomes full, trace_seq_vprintf() no longer consumes
arguments from va_list, making va_list out of sync with format
processing by trace_check_vprintf().
This causes va_arg() in trace_check_vprintf() to return wrong
positional argument, which results into a WARN_ON_ONCE() hit.
ftrace_stress_test from LTP triggers this situation.
Fix it by explicitly avoiding further use if va_list at the point
when it's consistency can no longer be guaranteed.
Link: https://lkml.kernel.org/r/20211118145516.13219-1-nikita.yushchenko@virtuozzo.com
Signed-off-by: Nikita Yushchenko <nikita.yushchenko@virtuozzo.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9fc706108c15f8bc2d4ccccf8e50f74830fabd9 ]
perf_tip() may allocate memory or use a literal, this means memory
wasn't freed if allocated. Change the API so that literals aren't used.
At the same time add missing frees for system_path. These issues were
spotted using leak sanitizer.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20211118073804.2149974-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ca1f534a776cc7d42f2c33da4732b74ec2790cd ]
perf_hpp__column_unregister() removes an entry from a list but doesn't
free the memory causing a memory leak spotted by leak sanitizer.
Add the free while at the same time reducing the scope of the function
to static.
Signed-off-by: Ian Rogers <irogers@google.com>
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lore.kernel.org/lkml/20211118071247.2140392-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e1a8d9f683260d50e0a14176d3f7c46a93b2700 ]
'perf inject' is currently not working for Arm SPE. When you try to run
'perf inject' and 'perf report' with a perf.data file that contains SPE
traces, the tool reports a "Bad address" error:
# ./perf record -e arm_spe_0/ts_enable=1,store_filter=1,branch_filter=1,load_filter=1/ -a -- sleep 1
# ./perf inject -i perf.data -o perf.inject.data --itrace
# ./perf report -i perf.inject.data --stdio
0x42c00 [0x8]: failed to process type: 9 [Bad address]
Error:
failed to process sample
As far as I know, the issue was first spotted in [1], but 'perf inject'
was not yet injecting the samples. This patch does something similar to
what cs_etm does for injecting the samples [2], but for SPE.
[1] https://patchwork.kernel.org/project/linux-arm-kernel/cover/20210412091006.468557-1-leo.yan@linaro.org/#24117339
[2] https://git.kernel.org/pub/scm/linux/kernel/git/acme/linux.git/tree/tools/perf/util/cs-etm.c?h=perf/core&id=133fe2e617e48ca0948983329f43877064ffda3e#n1196
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: German Gomez <german.gomez@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20211105104130.28186-2-german.gomez@arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db4b284029099224f387d75198e5995df1cb8aef ]
andle 'p_stage_cyc' (for pipeline stage cycles) sort key with the same
rationale as for the 'weight' and 'local_weight', see the fix in this
series for a full explanation.
Not sure it also needs the local and global variants.
But I couldn't test it actually because I don't have the machine.
Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211105225617.151364-3-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d03c75363eeca861c843319a0e6f4426234ed6c ]
Handle 'ins_lat' (for instruction latency) and 'local_ins_lat' sort keys
with the same rationale as for the 'weight' and 'local_weight', see the
previous fix in this series for a full explanation.
But I couldn't test it actually, so only build tested.
Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211105225617.151364-2-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 784e8adda4cdb3e2510742023729851b6c08803c ]
Currently, the 'weight' field in the perf sample has latency information
for some instructions like in memory accesses. And perf tool has 'weight'
and 'local_weight' sort keys to display the info.
But it's somewhat confusing what it shows exactly. In my understanding,
'local_weight' shows a weight in a single sample, and (global) 'weight'
shows a sum of the weights in the hist_entry.
For example:
$ perf mem record -t load dd if=/dev/zero of=/dev/null bs=4k count=1M
$ perf report --stdio -n -s +local_weight
...
#
# Overhead Samples Command Shared Object Symbol Local Weight
# ........ ....... ....... ................ ......................... ............
#
21.23% 313 dd [kernel.vmlinux] [k] lockref_get_not_zero 32
12.43% 183 dd [kernel.vmlinux] [k] lockref_get_not_zero 35
11.97% 159 dd [kernel.vmlinux] [k] lockref_get_not_zero 36
10.40% 141 dd [kernel.vmlinux] [k] lockref_put_return 32
7.63% 113 dd [kernel.vmlinux] [k] lockref_get_not_zero 33
6.37% 92 dd [kernel.vmlinux] [k] lockref_get_not_zero 34
6.15% 90 dd [kernel.vmlinux] [k] lockref_put_return 33
...
So let's look at the 'lockref_get_not_zero' symbols. The top entry
shows that 313 samples were captured with 'local_weight' 32, so the
total weight should be 313 x 32 = 10016. But it's not the case:
$ perf report --stdio -n -s +local_weight,weight -S lockref_get_not_zero
...
#
# Overhead Samples Command Shared Object Local Weight Weight
# ........ ....... ....... ................ ............ ......
#
1.36% 4 dd [kernel.vmlinux] 36 144
0.47% 4 dd [kernel.vmlinux] 37 148
0.42% 4 dd [kernel.vmlinux] 32 128
0.40% 4 dd [kernel.vmlinux] 34 136
0.35% 4 dd [kernel.vmlinux] 36 144
0.34% 4 dd [kernel.vmlinux] 35 140
0.30% 4 dd [kernel.vmlinux] 36 144
0.30% 4 dd [kernel.vmlinux] 34 136
0.30% 4 dd [kernel.vmlinux] 32 128
0.30% 4 dd [kernel.vmlinux] 32 128
...
With the 'weight' sort key, it's divided to 4 samples even with the same
info ('comm', 'dso', 'sym' and 'local_weight'). I don't think this is
what we want.
I found this because of the way it aggregates the 'weight' value. Since
it's not a period, we should not add them in the he->stat. Otherwise,
two 32 'weight' entries will create a 64 'weight' entry.
After that, new 32 'weight' samples don't have a matching entry so it'd
create a new entry and make it a 64 'weight' entry again and again.
Later, they will be merged into 128 'weight' entries during the
hists__collapse_resort() with 4 samples, multiple times like above.
Let's keep the weight and display it differently. For 'local_weight',
it can show the weight as is, and for (global) 'weight' it can display
the number multiplied by the number of samples.
With this change, I can see the expected numbers.
$ perf report --stdio -n -s +local_weight,weight -S lockref_get_not_zero
...
#
# Overhead Samples Command Shared Object Local Weight Weight
# ........ ....... ....... ................ ............ .....
#
21.23% 313 dd [kernel.vmlinux] 32 10016
12.43% 183 dd [kernel.vmlinux] 35 6405
11.97% 159 dd [kernel.vmlinux] 36 5724
7.63% 113 dd [kernel.vmlinux] 33 3729
6.37% 92 dd [kernel.vmlinux] 34 3128
4.17% 59 dd [kernel.vmlinux] 37 2183
0.08% 1 dd [kernel.vmlinux] 269 269
0.08% 1 dd [kernel.vmlinux] 38 38
Reviewed-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20211105225617.151364-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fa68da72c3be09e06dd833258ee89c33374195f ]
The definition of macro MOTO_SROM_BUG is:
#define MOTO_SROM_BUG (lp->active == 8 && (get_unaligned_le32(
dev->dev_addr) & 0x00ffffff) == 0x3e0008)
and the if statement
if (MOTO_SROM_BUG) lp->active = 0;
using this macro indicates lp->active could be 8. If lp->active is 8 and
the second comparison of this macro is false. lp->active will remain 8 in:
lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].mci = *p;
However, the length of array lp->phy is 8, so array overflows can occur.
To fix these possible array overflows, we first check lp->active and then
return -EINVAL if it is greater or equal to ARRAY_SIZE(lp->phy) (i.e. 8).
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61217be886b5f7402843677e4be7e7e83de9cb41 ]
In line 5001, if all id in the array 'lp->phy[8]' is not 0, when the
'for' end, the 'k' is 8.
At this time, the array 'lp->phy[8]' may be out of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f9c55c8066bcd93ac25234a02585701fe2e31df ]
The offset value is used in pointer math on skb->data.
Since ipv6_skip_exthdr may return -1 the pointer to uh and th
may not point to the actual udp and tcp headers and potentially
overwrite other stuff. This is why I think this should be checked.
EDIT: added {}'s, thanks Kees
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a66998e0fbf213d47d02813b9679426129d0d114 ]
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c5f641a5914ce0303b06bcfcd7674ee64aeebe9 ]
The StorageD3Enable _DSD is used for the vendor to indicate that the disk
should be opted into or out of a different behavior based upon the platform
design.
For AMD's Renoir and Green Sardine platforms it's important that any
attached SATA storage has transitioned into DevSlp when s2idle is used.
If the disk is left in active/partial/slumber, then the system is not able
to resume properly.
When the StorageD3Enable _DSD is detected, check the system is using s2idle
and DevSlp is enabled and if so explicitly wait long enough for the disk to
enter DevSlp.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Link: https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527f69204fe35f341cb599f1cb01bd02daf4374 ]
AMD requires that the SATA controller be configured for devsleep in order
for S0i3 entry to work properly.
commit b1a9585cc396 ("ata: ahci: Enable DEVSLP by default on x86 with
SLP_S0") sets up a kernel policy to enable devsleep on Intel mobile
platforms that are using s0ix. Add the PCI ID for the SATA controller in
Green Sardine platforms to extend this policy by default for AMD based
systems using s0i3 as well.
Cc: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214091
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27dfaedc0d321b4ea4e10c53e4679d6911ab17aa ]
In function amdgpu_get_xgmi_hive, when kobject_init_and_add failed
There is a potential memleak if not call kobject_put.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cf49e00d40d5132e3d067b5aa6d84791929ab15 ]
In SRIOV configuration, the reset may failed to bring asic back to normal but stop cpsch
already been called, the start_cpsch will not be called since there is no resume in this
case. When reset been triggered again, driver should avoid to do uninitialization again.
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be83a5676767c99c2417083c29d42aa1e109a69d ]
Print Navi1x fine grained clocks in a consistent manner with other SOCs.
Don't show aritificial DPM level when the current clock equals min or max.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f77b83b5bbab53d2be339184838b19ed2c62c0a5 ]
Like ThinkaPad Thunderbolt 4 Dock, more Lenovo docks start to use the original
Realtek USB ethernet chip ID 0bda:8153.
Lenovo Docks always use their own IDs for usb hub, even for older Docks.
If parent hub is from Lenovo, then r8152 should try MAC passthrough.
Verified on Lenovo TBT3 dock too.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0c2f8b6709a9a4af175497ca65f93804f57b248 ]
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
Link: https://lore.kernel.org/r/20211105221048.6541-2-michael.christie@oracle.com
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99b63316c39988039965693f5f43d8b4ccb1c86c ]
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
