IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 0582d984793d30442da88fe458674502bad1ad29 ]
Fix multiple W=1 kernel-doc warnings in i2c-rk3x.c:
drivers/i2c/busses/i2c-rk3x.c:83: warning: missing initial short description on line:
* struct i2c_spec_values:
drivers/i2c/busses/i2c-rk3x.c:139: warning: missing initial short description on line:
* struct rk3x_i2c_calced_timings:
drivers/i2c/busses/i2c-rk3x.c:162: warning: missing initial short description on line:
* struct rk3x_i2c_soc_data:
drivers/i2c/busses/i2c-rk3x.c:242: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a START condition, which triggers a REG_INT_START interrupt.
drivers/i2c/busses/i2c-rk3x.c:261: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
drivers/i2c/busses/i2c-rk3x.c:304: warning: expecting prototype for Setup a read according to i2c(). Prototype was for rk3x_i2c_prepare_read() instead
drivers/i2c/busses/i2c-rk3x.c:335: warning: expecting prototype for Fill the transmit buffer with data from i2c(). Prototype was for rk3x_i2c_fill_transmit_buf() instead
drivers/i2c/busses/i2c-rk3x.c:535: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Get timing values of I2C specification
drivers/i2c/busses/i2c-rk3x.c:552: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate divider values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:713: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate timing values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:963: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Setup I2C registers for an I2C operation specified by msgs, num.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78a4471fa1a76a8bef4919105de67660a89a1e9b ]
During boot of I2SE Duckbill the kernel log contains a
confusing error:
Failed to request dma
This is caused by i2c-mxs tries to request a not yet available DMA
channel (-EPROBE_DEFER). So suppress this message by using
dev_err_probe().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8c37bc514514999e62a17e95160ed9ebf75ca8d ]
In functions i2c_dw_scl_lcnt() and i2c_dw_scl_hcnt() may have overflow
by depending on the values of the given parameters including the ic_clk.
For example in our use case where ic_clk is larger than one million,
multiplication of ic_clk * 4700 will result in 32 bit overflow.
Add cast of u64 to the calculation to avoid multiplication overflow, and
use the corresponding define for divide.
Fixes: 2373f6b9744d ("i2c-designware: split of i2c-designware.c into core and bus specific parts")
Signed-off-by: Lareine Khawaly <lareine@amazon.com>
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 544a8d75f3d6e60e160cd92dc56321484598a993 upstream.
Add an atomic_xfer method to the driver so that it behaves correctly
when controlling a PMIC that is responsible for device shutdown.
The atomic_xfer method added is similar to the one from the i2c-rk3x
driver. When running an atomic_xfer a bool flag in the driver data is
set, the interrupt is not unmasked on transfer start, and the IRQ
handler is manually invoked while waiting for pending transfers to
complete.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09b343038e3470e4d0da45f0ee09fb42107e5314 upstream.
When I attempt to shut down (or reboot) my R8 based NTC CHIP with this
i2c driver I get the following error: "i2c i2c-0: mv64xxx: I2C bus
locked, block: 1, time_left: 0". Reboots are successful but shutdowns
freeze. If I comment out the shutdown routine the device both reboots
and shuts down successfully without receiving this error (however it
does receive a warning of missing atomic_xfer).
It appears that very few i2c drivers have a shutdown method, I assume
because these devices are often used to communicate with PMICs (such
as in my case with the R8 based NTC CHIP). I'm proposing we simply
remove this method so long as it doesn't cause trouble for others
downstream. I'll work on an atomic_xfer method and submit that in
a different patch.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39244cc754829bf707dccd12e2ce37510f5b1f8d ]
When the driver does not check the data from the user, the variable
'data->block[0]' may be very large to cause an out-of-bounds bug.
The following log can reveal it:
[ 33.995542] i2c i2c-1: ioctl, cmd=0x720, arg=0x7ffcb3dc3a20
[ 33.995978] ismt_smbus 0000:00:05.0: I2C_SMBUS_BLOCK_DATA: WRITE
[ 33.996475] ==================================================================
[ 33.996995] BUG: KASAN: out-of-bounds in ismt_access.cold+0x374/0x214b
[ 33.997473] Read of size 18446744073709551615 at addr ffff88810efcfdb1 by task ismt_poc/485
[ 33.999450] Call Trace:
[ 34.001849] memcpy+0x20/0x60
[ 34.002077] ismt_access.cold+0x374/0x214b
[ 34.003382] __i2c_smbus_xfer+0x44f/0xfb0
[ 34.004007] i2c_smbus_xfer+0x10a/0x390
[ 34.004291] i2cdev_ioctl_smbus+0x2c8/0x710
[ 34.005196] i2cdev_ioctl+0x5ec/0x74c
Fix this bug by checking the size of 'data->block[0]' first.
Fixes: 13f35ac14cd0 ("i2c: Adding support for Intel iSMT SMBus 2.0 host controller")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d47b79d2bd39cc6369eccf94a06568d84c906ae ]
It will cause null-ptr-deref in resource_size(), if platform_get_resource()
returns NULL, move calling resource_size() after devm_ioremap_resource() that
will check 'res' to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: b3fdd32799d8 ("i2c: mux: Add register-based mux i2c-mux-reg")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d36678f7905cbd1dc55a8a96e066dafd749d4600 ]
Recent changes to the DMA code has resulting in the IMX driver failing
I2C transfers when the buffer has been vmalloc. Only perform DMA
transfers if the message has the I2C_M_DMA_SAFE flag set, indicating
the client is providing a buffer which is DMA safe.
This is a minimal fix for stable. The I2C core provides helpers to
allocate a bounce buffer. For a fuller fix the master should make use
of these helpers.
Fixes: 4544b9f25e70 ("dma-mapping: Add vmap checks to dma_map_single()")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 145900cf91c4b32ac05dbc8675a0c7f4a278749d ]
A problem about i2c-npcm7xx create debugfs failed is triggered with the
following log given:
[ 173.827310] debugfs: Directory 'npcm_i2c' with parent '/' already present!
The reason is that npcm_i2c_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of npcm_i2c can never be created later.
npcm_i2c_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6643d7207c572c1b0305ed505101f15502c6c87 ]
Dell Vostro 5568 laptop has lis3lv02d, but its i2c address is not known
to the kernel. Add this address.
Output of "cat /sys/devices/platform/lis3lv02d/position" on Dell Vostro
5568 laptop:
- Horizontal: (-18,0,1044)
- Front elevated: (522,-18,1080)
- Left elevated: (-18,-360,1080)
- Upside down: (36,108,-1134)
Signed-off-by: Nam Cao <namcaov@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdbf26251d3b35c4ccaea0c3a6de4318f727d3d2 ]
When the I2C controllers are running in DMA mode, it is the DMA engine
that performs the memory accesses rather than the I2C controller. Pass
the DMA engine's struct device pointer to the DMA API to make sure the
correct DMA operations are used.
This fixes an issue where the DMA engine's SMMU stream ID needs to be
misleadingly set for the I2C controllers in device tree.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 569bea74c94d37785682b11bab76f557520477cd ]
In piix4_probe(), the piix4 adapter will be registered in:
piix4_probe()
piix4_add_adapters_sb800() / piix4_add_adapter()
i2c_add_adapter()
Based on the probed device type, piix4_add_adapters_sb800() or single
piix4_add_adapter() will be called.
For the former case, piix4_adapter_count is set as the number of adapters,
while for antoher case it is not set and kept default *zero*.
When piix4 is removed, piix4_remove() removes the adapters added in
piix4_probe(), basing on the piix4_adapter_count value.
Because the count is zero for the single adapter case, the adapter won't
be removed and makes the sources allocated for adapter leaked, such as
the i2c client and device.
These sources can still be accessed by i2c or bus and cause problems.
An easily reproduced case is that if a new adapter is registered, i2c
will get the leaked adapter and try to call smbus_algorithm, which was
already freed:
Triggered by: rmmod i2c_piix4 && modprobe max31730
BUG: unable to handle page fault for address: ffffffffc053d860
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 3752 Comm: modprobe Tainted: G
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
RIP: 0010:i2c_default_probe (drivers/i2c/i2c-core-base.c:2259) i2c_core
RSP: 0018:ffff888107477710 EFLAGS: 00000246
...
<TASK>
i2c_detect (drivers/i2c/i2c-core-base.c:2302) i2c_core
__process_new_driver (drivers/i2c/i2c-core-base.c:1336) i2c_core
bus_for_each_dev (drivers/base/bus.c:301)
i2c_for_each_dev (drivers/i2c/i2c-core-base.c:1823) i2c_core
i2c_register_driver (drivers/i2c/i2c-core-base.c:1861) i2c_core
do_one_initcall (init/main.c:1296)
do_init_module (kernel/module/main.c:2455)
...
</TASK>
---[ end trace 0000000000000000 ]---
Fix this problem by correctly set piix4_adapter_count as 1 for the
single adapter so it can be normally removed.
Fixes: 528d53a1592b ("i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8caf0a0e04583fb71e21495bef84509182227ea ]
The missing "platform" alias is required for the mgb4 v4l2 driver to load
the i2c controller driver when probing the HW.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61775d54d674ff8ec3658495e0dbc537227dc5c1 upstream.
When we compile-in the CCI along with the imx412 driver and run on the RB5
we see that i2c_add_adapter() causes the probe of the imx412 driver to
happen.
This probe tries to perform an i2c xfer() and the xfer() in i2c-qcom-cci.c
fails on pm_runtime_get() because the i2c-qcom-cci.c::probe() function has
not completed to pm_runtime_enable(dev).
Fix this sequence by ensuring pm_runtime_xxx() calls happen prior to adding
the i2c adapter.
Fixes: e517526195de ("i2c: Add Qualcomm CCI I2C driver")
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86067ccfa1424a26491542d6f6d7546d40b61a10 ]
Linux is not the only entity using the BlueField I2C busses so
support a lock mechanism provided by hardware to avoid issues
when multiple entities are trying to access the same bus.
The lock is acquired whenever written explicitely or the lock
register is read. So make sure it is always released at the end
of a successful or failed transaction.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 301c8f5c32c8fb79c67539bc23972dc3ef48024c upstream.
Commit c7b79a752871 ("mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI
IDs") caused a regression on certain Gigabyte motherboards for Intel
Alder Lake-S where system crashes to NULL pointer dereference in
i2c_dw_xfer_msg() when system resumes from S3 sleep state ("deep").
I was able to debug the issue on Gigabyte Z690 AORUS ELITE and made
following notes:
- Issue happens when resuming from S3 but not when resuming from
"s2idle"
- PCI device 00:15.0 == i2c_designware.0 is already in D0 state when
system enters into pci_pm_resume_noirq() while all other i2c_designware
PCI devices are in D3. Devices were runtime suspended and in D3 prior
entering into suspend
- Interrupt comes after pci_pm_resume_noirq() when device interrupts are
re-enabled
- According to register dump the interrupt really comes from the
i2c_designware.0. Controller is enabled, I2C target address register
points to a one detectable I2C device address 0x60 and the
DW_IC_RAW_INTR_STAT register START_DET, STOP_DET, ACTIVITY and
TX_EMPTY bits are set indicating completed I2C transaction.
My guess is that the firmware uses this controller to communicate with
an on-board I2C device during resume but does not disable the controller
before giving control to an operating system.
I was told the UEFI update fixes this but never the less it revealed the
driver is not ready to handle TX_EMPTY (or RX_FULL) interrupt when device
is supposed to be idle and state variables are not set (especially the
dev->msgs pointer which may point to NULL or stale old data).
Introduce a new software status flag STATUS_ACTIVE indicating when the
controller is active in driver point of view. Now treat all interrupts
that occur when is not set as unexpected and mask all interrupts from
the controller.
Fixes: c7b79a752871 ("mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs")
Reported-by: Samuel Clark <slc2015@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215907
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 37f071ec327b04c83d47637c5e5c2199b39899ca ]
The i2c-mlxbf.c driver is currently broken because there is a bug
in the calculation of the frequency. core_f, core_r and core_od
are components read from hardware registers and are used to
compute the frequency used to compute different timing parameters.
The shifting mechanism used to get core_f, core_r and core_od is
wrong. Use FIELD_GET to mask and shift the bitfields properly.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de24aceb07d426b6f1c59f33889d6a964770547b ]
memcpy() is called in a loop while 'operation->length' upper bound
is not checked and 'data_idx' also increments.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a5be6d1340c0fefcee8a6489cff7fd88a0d5b85 ]
Correct the base address used during io write.
This bug had no impact over the overall functionality of the read and write
transactions. MLXBF_I2C_CAUSE_OR_CLEAR=0x18 so writing to (smbus->io + 0x18)
instead of (mst_cause->ioi + 0x18) actually writes to the sc_low_timeout
register which just sets the timeout value before a read/write aborts.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 085aacaa73163f4b8a89dec24ecb32cfacd34017 ]
pm_runtime_get_sync() returning 1 also means the device is powered. So
resetting the chip registers in .remove() is possible and should be
done.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: d98bdd3a5b50 ("i2c: imx: Make sure to unregister adapter on remove()")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d98bdd3a5b50446d8e010be5b04ce81c4eabf728 upstream.
If for whatever reasons pm_runtime_resume_and_get() fails and .remove() is
exited early, the i2c adapter stays around and the irq still calls its
handler, while the driver data and the register mapping go away. So if
later the i2c adapter is accessed or the irq triggers this results in
havoc accessing freed memory and unmapped registers.
So unregister the software resources even if resume failed, and only skip
the hardware access in that case.
Fixes: 588eb93ea49f ("i2c: imx: add runtime pm support to improve the performance")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6435319c34704994e19b0767f6a4e6f37439867b ]
In i2c_mux_probe(), we should call of_node_put() when breaking out
of for_each_child_of_node() which will automatically increase and
decrease the refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fdf6d97f03035ad5298e2d1635036c74c2090ed ]
SMBus packet error checking (PEC) is implemented by appending one
additional byte of checksum data at the end of the message. This provides
additional protection and allows to detect data corruption on the I2C bus.
SMBus block reads support variable length reads. The first byte in the read
message is the number of available data bytes.
The combination of PEC and block read is currently not supported by the
Cadence I2C driver.
* When PEC is enabled the maximum transfer length for block reads
increases from 33 to 34 bytes.
* The I2C core smbus emulation layer relies on the driver updating the
`i2c_msg` `len` field with the number of received bytes. The updated
length is used when checking the PEC.
Add support to the Cadence I2C driver for handling SMBus block reads with
PEC. To determine the maximum transfer length uses the initial `len` value
of the `i2c_msg`. When PEC is enabled this will be 2, when it is disabled
it will be 1.
Once a read transfer is done also increment the `len` field by the amount
of received data bytes.
This change has been tested with a UCM90320 PMBus power monitor, which
requires block reads to access certain data fields, but also has PEC
enabled by default.
Fixes: df8eb5691c48 ("i2c: Add driver for Cadence I2C controller")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4c72c06c367758a14f227c847f9d623f1994ecf ]
Free the adap structure only after we are done using it.
This patch just moves the put_device() down a bit to avoid the
use after free.
Fixes: 611e12ea0f12 ("i2c: core: manage i2c bus device refcount in i2c_[get|put]_adapter")
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
[wsa: added comment to the code, added Fixes tag]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47d506d1a28fd10a9fb1f33df5622d88fae72095 ]
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ca8ca873d454635c20d508261bfc0081af75cf8 ]
Problems were observed on the Xilinx ZynqMP platform with large I2C reads.
When a read of 277 bytes was performed, the controller NAKed the transfer
after only 252 bytes were transferred and returned an ENXIO error on the
transfer.
There is some code in cdns_i2c_master_isr to handle this case by resetting
the transfer count in the controller before it reaches 0, to allow larger
transfers to work, but it was conditional on the CDNS_I2C_BROKEN_HOLD_BIT
quirk being set on the controller, and ZynqMP uses the r1p14 version of
the core where this quirk is not being set. The requirement to do this to
support larger reads seems like an inherently required workaround due to
the core only having an 8-bit transfer size register, so it does not
appear that this should be conditional on the broken HOLD bit quirk which
is used elsewhere in the driver.
Remove the dependency on the CDNS_I2C_BROKEN_HOLD_BIT for this transfer
size reset logic to fix this problem.
Fixes: 63cab195bf49 ("i2c: removed work arounds in i2c driver for Zynq Ultrascale+ MPSoC")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Shubhrajyoti Datta <Shubhrajyoti.datta@amd.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ad59b397f86a4d8014966fdc0552095a0c4fb2b ]
The recently added support for EFCH MMIO regions introduced a memory
leak in that code path. The leak is caused by the fact that
release_resource() merely removes the resource from the tree but does
not free its memory. We need to call release_mem_region() instead,
which does free the memory. As a nice side effect, this brings back
some symmetry between the legacy and MMIO paths.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Terry Bowman <terry.bowman@amd.com>
Tested-by: Terry Bowman <Terry.Bowman@amd.com>
Fixes: 7c148722d074 ("i2c: piix4: Add EFCH MMIO support to region request and release")
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27071b5cbca59d8e8f8750c199a6cbf8c9799963 ]
Even though the DW I2C controller reference clock source is requested by
the method devm_clk_get() with non-optional clock requirement the way the
clock handler is used afterwards has a pure optional clock semantic
(though in some circumstances we can get a warning about the clock missing
printed in the system console). There is no point in reimplementing that
functionality seeing the kernel clock framework already supports the
optional interface from scratch. Thus let's convert the platform driver to
using it.
Note by providing this commit we get to fix two problems. The first one
was introduced in commit c62ebb3d5f0d ("i2c: designware: Add support for
an interface clock"). It causes not having the interface clock (pclk)
enabled/disabled in case if the reference clock isn't provided. The second
problem was first introduced in commit b33af11de236 ("i2c: designware: Do
not require clock when SSCN and FFCN are provided"). Since that
modification the deferred probe procedure has been unsupported in case if
the interface clock isn't ready.
Fixes: c62ebb3d5f0d ("i2c: designware: Add support for an interface clock")
Fixes: b33af11de236 ("i2c: designware: Do not require clock when SSCN and FFCN are provided")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ba12b56b9b844b83ed54fb7ed59fb0eb41e4045 ]
As platform_driver_register() could fail, it should be better
to deal with the return value in order to maintain the code
consisitency.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96789dce043f5bff8b7d62aa28d52a7c59403a84 ]
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3fe2ec59db1a7569e18594b9c0cf1f4f1afd498e ]
We have to take care of ID_P_PM_BLOCKED when bailing out during probe.
Fixes: 7ee24eb508d6 ("i2c: rcar: disable PM in multi-master mode")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5222d408de2a88e6b206c38217b48d092184553 ]
On some platforms in rare cases (1 to 100,000 transactions),
the i2c gets a spurious interrupt which means that we enter an interrupt
but in the interrupt handler we don't find any status bit that points to
the reason we got this interrupt.
This may be a case of a rare HW issue or signal integrity issue that is
still under investigation.
In order to overcome this we are doing the following:
1. Disable incoming interrupts in master mode only when slave mode is not
enabled.
2. Clear end of busy (EOB) after every interrupt.
3. Clear other status bits (just in case since we found them cleared)
4. Return correct status during the interrupt that will finish the
transaction.
On next xmit transaction if the bus is still busy the master will issue a
recovery process before issuing the new transaction.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea9f8426d17620214ee345ffb77ee6cc196ff14f ]
The SMBnCTL3 register is 8-bit wide and the 32-bit access was always
incorrect, but simply didn't cause a visible error on the 32-bit machine.
On the 64-bit machine, the kernel message reports that ESR value is
0x96000021. Checking Arm Architecture Reference Manual Armv8 suggests that
it's the alignment fault.
SMBnCTL3's address is 0xE.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6977262c2eee111645668fe9e235ef2f5694abf7 ]
Clang warns:
drivers/i2c/busses/i2c-at91-master.c:707:6: warning: variable 'dma_buf' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
if (dev->use_dma) {
^~~~~~~~~~~~
drivers/i2c/busses/i2c-at91-master.c:717:27: note: uninitialized use occurs here
i2c_put_dma_safe_msg_buf(dma_buf, m_start, !ret);
^~~~~~~
Initialize dma_buf to NULL, as i2c_put_dma_safe_msg_buf() is a no-op
when the first argument is NULL, which will work for the !dev->use_dma
case.
Fixes: 03fbb903c8bf ("i2c: at91: use dma safe buffers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1629
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fbb903c8bf7e53e101e8d9a7b261264317c411 ]
The supplied buffer might be on the stack and we get the following error
message:
[ 3.312058] at91_i2c e0070600.i2c: rejecting DMA map of vmalloc memory
Use i2c_{get,put}_dma_safe_msg_buf() to get a DMA-able memory region if
necessary.
Fixes: 60937b2cdbf9 ("i2c: at91: add dma support")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 690b2549b19563ec5ad53e5c82f6a944d910086e upstream.
The "data->block[0]" variable comes from the user and is a number
between 0-255. It needs to be capped to prevent writing beyond the end
of dma_buffer[].
Fixes: 5e9a97b1f449 ("i2c: ismt: Adding support for I2C_SMBUS_BLOCK_PROC_CALL")
Reported-and-tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03a35bc856ddc09f2cc1f4701adecfbf3b464cb3 ]
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly
found for TWSI controllers.
Signed-off-by: Szymon Balcerak <sbalcerak@marvell.com>
Signed-off-by: Piyush Malgujar <pmalgujar@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 17a0f3acdc6ec8b89ad40f6e22165a4beee25663 ]
Before sending a MSI the hardware writes information pertinent to the
interrupt cause to a memory location pointed by SMTICL register. This
memory holds three double words where the least significant bit tells
whether the interrupt cause of master/target/error is valid. The driver
does not use this but we need to set it up because otherwise it will
perform DMA write to the default address (0) and this will cause an
IOMMU fault such as below:
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0
[fault reason 05] PTE Write access is not set
To prevent this from happening, provide a proper DMA buffer for this
that then gets mapped by the IOMMU accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: From: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cf72f41808ab5db1d7718b999b3ff0166e67e45 upstream.
Enable EFCH MMIO using check for SMBus PCI revision ID value 0x51 or
greater. This PCI revision ID check will enable family 17h and future
AMD processors with the same EFCH SMBus controller HW.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 381a3083c6747ae5cdbef9b176d57d1b966db49f upstream.
AMD processors include registers capable of selecting between 2 SMBus
ports. Port selection is made during each user access by writing to
FCH::PM::DECODEEN[smbus0sel]. Change the driver to use MMIO during
SMBus port selection because cd6h/cd7h port I/O is not available on
later AMD processors.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46967bc1ee93acd1d8953c87dc16f43de4076f93 upstream.
The EFCH SMBus controller's base address is determined using details in
FCH::PM::DECODEEN[smbusasfiobase] and FCH::PM::DECODEEN[smbusasfioen].These
register fields were accessed using cd6h/cd7h port I/O. cd6h/cd7h port I/O
is no longer available in later AMD processors. Change base address
detection to use MMIO instead of port I/O cd6h/cd7h.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c148722d074c29fb998578eea5de3c14b9608c9 upstream.
EFCH cd6h/cd7h port I/O may no longer be available on later AMD
processors and it is recommended to use MMIO instead. Update the
request and release functions to support MMIO.
MMIO request/release and mmapping require details during cleanup.
Add a MMIO configuration structure containing resource and vaddress
details for mapping the region, accessing the region, and releasing
the region.
Signed-off-by: Terry Bowman <terry.bowman@amd.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
[wsa: rebased after fixup in previous patch]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
