IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 0571a753cb07982cc82f4a5115e0b321da89e1f3 ]
pxa168_eth_remove() firstly calls unregister_netdev(),
then cancels a timeout work. unregister_netdev() shuts down a device
interface and removes it from the kernel tables. If the timeout occurs
in parallel, the timeout work (pxa168_eth_tx_timeout_task) performs stop
and open of the device. It may lead to an inconsistent state and memory
leaks.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a28af7a3e85ddf358f8c41e401a33002f7a9587 ]
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09078368d516918666a0122f2533dc73676d3d7e ]
ieee80211_find_sta_by_ifaddr() must be called under the RCU lock and
the resulting pointer is only valid under RCU lock as well.
Fix ath10k_wmi_tlv_op_pull_peer_stats_info() to hold RCU lock before it
calls ieee80211_find_sta_by_ifaddr() and release it when the resulting
pointer is no longer needed.
This problem was found while reviewing code to debug RCU warn from
ath10k_wmi_tlv_parse_peer_stats_info().
Link: https://lore.kernel.org/linux-wireless/7230c9e5-2632-b77e-c4f9-10eca557a5bb@linuxfoundation.org/
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210210212107.40373-1-skhan@linuxfoundation.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e862a3e4088070de352fdafe9bd9e3ae0a95a33c ]
This ensure that previous association attempts do not leave stale statuses
on subsequent attempts.
This fixes the WARN_ON(!cr->bss)) from __cfg80211_connect_result() when
connecting to an AP after a previous connection failure (e.g. where EAP fails
due to incorrect psk but association succeeded). In some scenarios, indeed,
brcmf_is_linkup() was reporting a link up event too early due to stale
BRCMF_VIF_STATUS_ASSOC_SUCCESS bit, thus reporting to cfg80211 a connection
result with a zeroed bssid (vif->profile.bssid is still empty), causing the
WARN_ON due to the call to cfg80211_get_bss() with the empty bssid.
Signed-off-by: Luca Pesce <luca.pesce@vimar.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608807119-21785-1-git-send-email-luca.pesce@vimar.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e1caaf8ed22eb700cc47ec353816eee33186c1c ]
This patch fixes the max register value for the regmap.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-12-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e096a18867a5a989b510f6999d9c6b6622e8f7b ]
Since 20dd3850bcf8 ("can: Speed up CAN frame receiption by using
ml_priv") the CAN framework uses per device specific data in the AF_CAN
protocol. For this purpose the struct net_device->ml_priv is used. Later
the ml_priv usage in CAN was extended for other users, one of them being
CAN_J1939.
Later in the kernel ml_priv was converted to an union, used by other
drivers. E.g. the tun driver started storing it's stats pointer.
Since tun devices can claim to be a CAN device, CAN specific protocols
will wrongly interpret this pointer, which will cause system crashes.
Mostly this issue is visible in the CAN_J1939 stack.
To fix this issue, we request a dedicated CAN pointer within the
net_device struct.
Reported-by: syzbot+5138c4dd15a0401bec7b@syzkaller.appspotmail.com
Fixes: 20dd3850bcf8 ("can: Speed up CAN frame receiption by using ml_priv")
Fixes: ffd956eef69b ("can: introduce CAN midlayer private and allocate it automatically")
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Fixes: 497a5757ce4e ("tun: switch to net core provided statistics counters")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210223070127.4538-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e77f70e734584e0ad1038e459ed3fd2400f873a ]
This patch moves the CAN driver related infrastructure into a separate subdir.
It will be split into more files in the coming patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7867299cde34e9c2d2c676f2a384a9d5853b914d ]
The condition should be skipped if CPU ID equal to nthreads.
The patch doesn't fix any actual issue since
nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS).
On all current Armada platforms, the number of CPU's is
less than MVPP2_MAX_THREADS.
Fixes: e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5d7047ed6b7214fbabc16d8712a822e256b1aa44 upstream.
In commit 6417f03132a6 ("module: remove never implemented
MODULE_SUPPORTED_DEVICE") the MODULE_SUPPORTED_DEVICE macro was
removed from the kerne entirely. Shortly before this patch was applied
mainline the commit 59ec7b89ed3e ("can: peak_usb: add forgotten
supported devices") was added to net/master. As this would result in a
merge conflict, let's revert this patch.
Fixes: 59ec7b89ed3e ("can: peak_usb: add forgotten supported devices")
Link: https://lore.kernel.org/r/20210320192649.341832-1-mkl@pengutronix.de
Suggested-by: Leon Romanovsky <leon@kernel.org>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream.
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68f7 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a5ca857079ea022e0b1b17fc154f7ad7dbc150f upstream.
When a non-initial netns is destroyed, the usual policy is to delete
all virtual network interfaces contained, but move physical interfaces
back to the initial netns. This keeps the physical interface visible
on the system.
CAN devices are somewhat special, as they define rtnl_link_ops even
if they are physical devices. If a CAN interface is moved into a
non-initial netns, destroying that netns lets the interface vanish
instead of moving it back to the initial netns. default_device_exit()
skips CAN interfaces due to having rtnl_link_ops set. Reproducer:
ip netns add foo
ip link set can0 netns foo
ip netns delete foo
WARNING: CPU: 1 PID: 84 at net/core/dev.c:11030 ops_exit_list+0x38/0x60
CPU: 1 PID: 84 Comm: kworker/u4:2 Not tainted 5.10.19 #1
Workqueue: netns cleanup_net
[<c010e700>] (unwind_backtrace) from [<c010a1d8>] (show_stack+0x10/0x14)
[<c010a1d8>] (show_stack) from [<c086dc10>] (dump_stack+0x94/0xa8)
[<c086dc10>] (dump_stack) from [<c086b938>] (__warn+0xb8/0x114)
[<c086b938>] (__warn) from [<c086ba10>] (warn_slowpath_fmt+0x7c/0xac)
[<c086ba10>] (warn_slowpath_fmt) from [<c0629f20>] (ops_exit_list+0x38/0x60)
[<c0629f20>] (ops_exit_list) from [<c062a5c4>] (cleanup_net+0x230/0x380)
[<c062a5c4>] (cleanup_net) from [<c0142c20>] (process_one_work+0x1d8/0x438)
[<c0142c20>] (process_one_work) from [<c0142ee4>] (worker_thread+0x64/0x5a8)
[<c0142ee4>] (worker_thread) from [<c0148a98>] (kthread+0x148/0x14c)
[<c0148a98>] (kthread) from [<c0100148>] (ret_from_fork+0x14/0x2c)
To properly restore physical CAN devices to the initial netns on owning
netns exit, introduce a flag on rtnl_link_ops that can be set by drivers.
For CAN devices setting this flag, default_device_exit() considers them
non-virtual, applying the usual namespace move.
The issue was introduced in the commit mentioned below, as at that time
CAN devices did not have a dellink() operation.
Fixes: e008b5fc8dc7 ("net: Simplfy default_device_exit and improve batching.")
Link: https://lore.kernel.org/r/20210302122423.872326-1-martin@strongswan.org
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 014dfa26ce1c647af09bf506285ef67e0e3f0a6b ]
MTU cannot be changed on dwmac-sun8i. (ip link set eth0 mtu xxx returning EINVAL)
This is due to tx_fifo_size being 0, since this value is used to compute valid
MTU range.
Like dwmac-sunxi (with commit 806fd188ce2a ("net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes"))
dwmac-sun8i need to have tx and rx fifo sizes set.
I have used values from datasheets.
After this patch, setting a non-default MTU (like 1000) value works and network is still useable.
Tested-on: sun8i-h3-orangepi-pc
Tested-on: sun8i-r40-bananapi-m2-ultra
Tested-on: sun50i-a64-bananapi-m64
Tested-on: sun50i-h5-nanopi-neo-plus2
Tested-on: sun50i-h6-pine-h64
Fixes: 9f93ac8d408 ("net-next: stmmac: Add dwmac-sun8i")
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f91a50d8b51b5c8ef1cfb08115a005bba4250507 ]
If the USB host controller is EHCI, the throughput is reduced from
300Mb/s to 60Mb/s, when the rx buffer size is modified from 16K to
32K.
According to the EHCI spec, the maximum size of the qTD is 20K.
Therefore, when the driver uses more than 20K buffer, the latency
time of EHCI would be increased. And, it let the RTL8153A get worse
throughput.
However, the driver uses alloc_pages() for rx buffer, so I limit
the rx buffer to 16K rather than 20K.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205923
Fixes: ec5791c202ac ("r8152: separate the rx buffer size")
Reported-by: Robert Davies <robdavies1977@gmail.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c79a707072fe3fea0e3c92edee6ca85c1e53c29f ]
Set the disconnected flag before releasing the data interface in case
netdev registration fails to avoid having the disconnect callback try to
deregister the never registered netdev (and trigger a WARN_ON()).
Fixes: 87cf65601e17 ("USB host CDC Phonet network interface driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64451b98306bf1334a62bcd020ec92bdb4cb68db ]
unmapping npc counter works in a way by traversing all mcam
entries to find which mcam rule is associated with counter.
But loop cursor variable 'entry' is not incremented before
checking next mcam entry which resulting in infinite loop.
This in turn hogs the kworker thread forever and no other
mbox message is processed by AF driver after that.
Fix this by updating entry value before checking next
mcam entry.
Fixes: a958dd59f9ce ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae2619dd4fccdad9876aa5f900bd85484179c50f ]
Current devlink code try to free already freed irqs as the
irq_allocate flag is not cleared after free leading to kernel
crash while removing rvu driver. The patch fixes the irq free
sequence and clears the irq_allocate flag on free.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8ce0275e45ec809a33f98fc080fe7921b720dfb ]
pre_tun_rule flows does not follow the usual add-flow path, instead
they are used to update the pre_tun table on the firmware. This means
that if the mask-id gets allocated here the firmware will never see the
"NFP_FL_META_FLAG_MANAGE_MASK" flag for the specific mask id, which
triggers the allocation on the firmware side. This leads to the firmware
mask being corrupted and causing all sorts of strange behaviour.
Fixes: f12725d98cbe ("nfp: flower: offload pre-tunnel rules")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98d9ee64ee2cc9b1d1a8e26610ec4d0392ebe50 ]
For M_CAN peripherals, m_can_rx_handler() was called with quota = 1,
which caused any error handling to block RX from taking place until
the next time the IRQ handler is called. This had been observed to
cause RX to be blocked indefinitely in some cases.
This is fixed by calling m_can_rx_handler with a sensibly high quota.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Link: https://lore.kernel.org/r/20210303144350.4093750-1-torin@maxiluxsystems.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0e399f3baf42279f48991554240af8c457535d1 ]
Message loss from RX FIFO 0 is already handled in
m_can_handle_lost_msg(), with netdev output included.
Removing this warning also improves driver performance under heavy
load, where m_can_do_rx_poll() may be called many times before this
interrupt is cleared, causing this message to be output many
times (thanks Mariusz Madej for this report).
Fixes: e0d1f4816f2a ("can: m_can: add Bosch M_CAN controller support")
Link: https://lore.kernel.org/r/20210303103151.3760532-1-torin@maxiluxsystems.com
Reported-by: Mariusz Madej <mariusz.madej@xtrack.com>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e2fe01dd6f98da6cae8b07cd5cfa67abc70d97d ]
Currently doing modprobe c_can_pci will make the kernel complain:
Unbalanced pm_runtime_enable!
this is caused by pm_runtime_enable() called before pm is initialized.
This fix is similar to 227619c3ff7c, move those pm_enable/disable code
to c_can_platform.
Fixes: 4cdd34b26826 ("can: c_can: Add runtime PM support to Bosch C_CAN/D_CAN controller")
Link: http://lore.kernel.org/r/20210302025542.987600-1-ztong0001@gmail.com
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0429d6d89f97ebff4f17f13f5b5069c66bde8138 ]
There is a UAF in c_can_pci_remove(). dev is released by
free_c_can_dev() and is used by pci_iounmap(pdev, priv->base) later.
To fix this issue, save the mmio address before releasing dev.
Fixes: 5b92da0443c2 ("c_can_pci: generic module for C_CAN/D_CAN on PCI")
Link: https://lore.kernel.org/r/20210301024512.539039-1-ztong0001@gmail.com
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c6e6bce08f918b64459415f58061d4d6df44994 ]
Under certain circumstances, when switching from Kvaser's linuxcan driver
(kvpciefd) to the SocketCAN driver (kvaser_pciefd), the bus load reporting
is not disabled.
This is flooding the kernel log with prints like:
[3485.574677] kvaser_pciefd 0000:02:00.0: Received unexpected packet type 0x00000009
Always put the controller in the expected state, instead of assuming that
bus load reporting is inactive.
Note: If bus load reporting is enabled when the driver is loaded, you will
still get a number of bus load packages (and printouts), before it is
disabled.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Link: https://lore.kernel.org/r/20210309091724.31262-1-jimmyassarsson@gmail.com
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c5e474bc1e1061fb037d13b5000b38967eb070 ]
For cases when flexcan is built-in, bitrate is still not set at
registering. So flexcan_chip_freeze() generates:
[ 1.860000] *** ZERO DIVIDE *** FORMAT=4
[ 1.860000] Current process id is 1
[ 1.860000] BAD KERNEL TRAP: 00000000
[ 1.860000] PC: [<402e70c8>] flexcan_chip_freeze+0x1a/0xa8
To allow chip freeze, using an hardcoded timeout when bitrate is still
not set.
Fixes: ec15e27cc890 ("can: flexcan: enable RX FIFO after FRZ/HALT valid")
Link: https://lore.kernel.org/r/20210315231510.650593-1-angelo@kernel-space.org
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
[mkl: use if instead of ? operator]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59ec7b89ed3e921cd0625a8c83f31a30d485fdf8 ]
Since the peak_usb driver also supports the CAN-USB interfaces
"PCAN-USB X6" and "PCAN-Chip USB" from PEAK-System GmbH, this patch adds
their names to the list of explicitly supported devices.
Fixes: ea8b65b596d7 ("can: usb: Add support of PCAN-Chip USB stamp module")
Fixes: f00b534ded60 ("can: peak: Add support for PCAN-USB X6 USB interface")
Link: https://lore.kernel.org/r/20210309082128.23125-3-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6897087323a2fde46df32917462750c069668b2f ]
The interrupt handler may set the flag to reset the mac in the future,
but that flag is not cleared once the reset has occurred.
Fixes: 10cbd6407609 ("ftgmac100: Rework NAPI & interrupts handling")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db74623a3850db99cb9692fda9e836a56b74198d ]
In qlcnic_83xx_get_minidump_template, fw_dump->tmpl_hdr was freed by
vfree(). But unfortunately, it is used when extended is true.
Fixes: 7061b2bdd620e ("qlogic: Deletion of unnecessary checks before two function calls")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b52912b8293f2c496f42583e65599aee606a0c18 ]
There is one e1e_wphy() call in e1000_set_d0_lplu_state_82571
that we have caught its return value but lack further handling.
Check and terminate the execution flow just like other e1e_wphy()
in this function.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f857f0321d0d0ea9b1a758bd55dc63d1cb2437 ]
A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b749 ("igb: reinit_locked() should be called
with rtnl_lock").
Added rtnl_lock() and rtnl_unlock() to avoid this.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a4a1cdc5ab52118c1f2b216f4240830b6528d32 ]
The Supported Pause Frame always display "No" even though the Advertised
pause frame showing the correct setting based on the pause parameters via
ethtool. Set bit in link_ksettings to "Supported" for Pause Frame.
Before output:
Supported pause frame use: No
Expected output:
Supported pause frame use: Symmetric
Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8876529465c368beafd51a70f79d7a738f2aadf4 ]
Fix Pause Frame Advertising when getting the advertisement via ethtool.
Remove setting the "advertising" bit in link_ksettings during default
case when Tx and Rx are in off state with Auto Negotiate off.
Below is the original output of advertisement link during Tx and Rx off:
Advertised pause frame use: Symmetric Receive-only
Expected output:
Advertised pause frame use: No
Fixes: 8c5ad0dae93c ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Malli C <mallikarjuna.chilakala@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47142ed6c34d544ae9f0463e58d482289cbe0d46 ]
Similar to commit 92696286f3bb37ba50e4bd8d1beb24afb759a799 ("net:
bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to
qualify the phydev->dev_flags based on whether the port is connected to
an internal or external PHY otherwise we risk having a flags collision
with a completely different interpretation depending on the driver.
Fixes: aa9aef77c761 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 385d40b042e60aa0b677d7b400a0fefb44bcbaf4 ]
The cited change added offload support for Geneve options without verifying
the validity of the options masks, this caused offload of rules with match
on Geneve options with class,type and data masks which are zero to fail.
Fix by ignoring the match on Geneve options in case option masks are
all zero.
Fixes: 9272e3df3023 ("net/mlx5e: Geneve, Add support for encap/decap flows offload")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edbea922025169c0e5cdca5ebf7bf5374cc5566c ]
Currently, veth_xmit() would call the skb_record_rx_queue() only when
there is XDP program loaded on peer interface in native mode.
If peer has XDP prog in generic mode, then netif_receive_generic_xdp()
has a call to netif_get_rxqueue(skb), so for multi-queue veth it will
not be possible to grab a correct rxq.
To fix that, store queue_mapping independently of XDP prog presence on
peer interface.
Fixes: 638264dc9022 ("veth: Support per queue XDP ring")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://lore.kernel.org/bpf/20210303152903.11172-1-maciej.fijalkowski@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 804741ac7b9f2fdebe3740cb0579cb8d94d49e60 upstream.
Since commit 8e850f25b581 ("net: socionext: Stop PHY before resetting
netsec") netsec_netdev_init() power downs phy before resetting the
controller. However, the state is not restored once the reset is
complete. As a result it is not possible to bring up network on a
platform with Broadcom BCM5482 phy.
Fix the issue by restoring phy power state after controller reset is
complete.
Fixes: 8e850f25b581 ("net: socionext: Stop PHY before resetting netsec")
Cc: stable@vger.kernel.org
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e2696223676d56db1a93acfca722c1b96cd552d ]
The second IRQ line really is optional, so use
platform_get_irq_optional() to obtain it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62765d39553cfd1ad340124fe1e280450e8c89e2 ]
When priv->rx_skbuff or priv->tx_skbuff is NULL, no error return code of
uhdlc_init() is assigned.
To fix this bug, ret is assigned with -ENOMEM in these cases.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 143c253f42bad20357e7e4432087aca747c43384 ]
When hns_assemble_skb() returns NULL to skb, no error return code of
hns_nic_clear_all_rx_fetch() is assigned.
To fix this bug, ret is assigned with -ENOMEM in this case.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8861bab48b6c1fc3cdbcab8ff9d1eaea43afe7f ]
When using jumbo packets and overrunning rx queue with napi enabled,
the following sequence is observed in gfar_add_rx_frag:
| lstatus | | skb |
t | lstatus, size, flags | first | len, data_len, *ptr |
---+--------------------------------------+-------+-----------------------+
13 | 18002348, 9032, INTERRUPT LAST | 0 | 9600, 8000, f554c12e |
12 | 10000640, 1600, INTERRUPT | 0 | 8000, 6400, f554c12e |
11 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, f554c12e |
10 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, f554c12e |
09 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, f554c12e |
08 | 14000640, 1600, INTERRUPT FIRST | 0 | 1600, 0, f554c12e |
07 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, f554c12e |
06 | 1c000080, 128, INTERRUPT LAST FIRST | 1 | 0, 0, abf3bd6e |
05 | 18002348, 9032, INTERRUPT LAST | 0 | 8000, 6400, c5a57780 |
04 | 10000640, 1600, INTERRUPT | 0 | 6400, 4800, c5a57780 |
03 | 10000640, 1600, INTERRUPT | 0 | 4800, 3200, c5a57780 |
02 | 10000640, 1600, INTERRUPT | 0 | 3200, 1600, c5a57780 |
01 | 10000640, 1600, INTERRUPT | 0 | 1600, 0, c5a57780 |
00 | 14000640, 1600, INTERRUPT FIRST | 1 | 0, 0, c5a57780 |
So at t=7 a new packets is started but not finished, probably due to rx
overrun - but rx overrun is not indicated in the flags. Instead a new
packets starts at t=8. This results in skb->len to exceed size for the LAST
fragment at t=13 and thus a negative fragment size added to the skb.
This then crashes:
kernel BUG at include/linux/skbuff.h:2277!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c04689f4] skb_pull+0x2c/0x48
LR [c03f62ac] gfar_clean_rx_ring+0x2e4/0x844
Call Trace:
[ec4bfd38] [c06a84c4] _raw_spin_unlock_irqrestore+0x60/0x7c (unreliable)
[ec4bfda8] [c03f6a44] gfar_poll_rx_sq+0x48/0xe4
[ec4bfdc8] [c048d504] __napi_poll+0x54/0x26c
[ec4bfdf8] [c048d908] net_rx_action+0x138/0x2c0
[ec4bfe68] [c06a8f34] __do_softirq+0x3a4/0x4fc
[ec4bfed8] [c0040150] run_ksoftirqd+0x58/0x70
[ec4bfee8] [c0066ecc] smpboot_thread_fn+0x184/0x1cc
[ec4bff08] [c0062718] kthread+0x140/0x144
[ec4bff38] [c0012350] ret_from_kernel_thread+0x14/0x1c
This patch fixes this by checking for computed LAST fragment size, so a
negative sized fragment is never added.
In order to prevent the newer rx frame from getting corrupted, the FIRST
flag is checked to discard the incomplete older frame.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 155b23e6e53475ca3b8c2a946299b4d4dd6a5a1e ]
RXMAC_BC_FRM_CNT_COUNT added to mp->rx_bcasts twice in a row
in niu_xmac_interrupt(). Remove the second addition.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6650d31f21b8a0043613ae0a4a2e42e49dc20b2d ]
When iavf_process_config() fails, no error return code of
iavf_init_get_resources() is assigned.
To fix this bug, err is assigned with the return value of
iavf_process_config(), and then err is checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38c26ff3048af50eee3fcd591921357ee5bfd9ee ]
When bdx_read_mac() fails, no error return code of bdx_probe()
is assigned.
To fix this bug, err is assigned with -EFAULT as error return code.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a766381634da19fc837619b0a34590498d9d29a ]
When ixgbe_fdir_write_perfect_filter_82599() fails,
input allocated by kzalloc() has not been freed,
which leads to memleak.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b5dc1a94d4f92b5845e98bd9ae344b26d933aad ]
This reverts commit 134f98bcf1b898fb9d6f2b91bc85dd2e5478b4b8.
The r8153_mac_clk_spd() is used for RTL8153A only, because the register
table of RTL8153B is different from RTL8153A. However, this function would
be called when RTL8153B calls r8153_first_init() and r8153_enter_oob().
That causes RTL8153B becomes unstable when suspending and resuming. The
worst case may let the device stop working.
Besides, revert this commit to disable MAC clock speed down for RTL8153A.
It would avoid the known issue when enabling U1. The data of the first
control transfer may be wrong when exiting U1.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a4d7234ae9a3bb31181f348ade9bbdb55aeb5c5 ]
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9788dcc5fe26baafd73bf9242b68900
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9b3827ee66cfcf297d0acd6ecf33653a5f297ef upstream.
Add support for being able to set the learning attribute on port, and
make sure that the standalone ports start up with learning disabled.
We can remove the code in bcm_sf2 that configured the ports learning
attribute because we want the standalone ports to have learning disabled
by default and port 7 cannot be bridged, so its learning attribute will
not change past its initial configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75be7fb7f978202c4c3a1a713af4485afb2ff5f6 ]
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d313 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58cab46c622d6324e47bd1c533693c94498e4172 ]
Struct i40e_veb is allocated in function i40e_setup_pf_switch, and
stored to an array field veb inside struct i40e_pf. However when
i40e_setup_misc_vector fails, this memory leaks.
Fix this by calling exit and teardown functions.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
