IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 5a3c680aa2c12c90c44af383fe6882a39875ab81 upstream.
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09cfae9f13d51700b0fecf591dcd658fc5375428 upstream.
When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.
The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.
Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.
Cc: stable@vger.kernel.org
Fixes: 0c5661ecc5dd7 ("ixgbe: fix crash in build_skb Rx code path")
Signed-off-by: Markus Boehme <markubo@amazon.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9a72f874d5b95cef0765bafc56005a50f72c5fe ]
When registering the MDIO bus for a r8169 device, we use the PCI
bus/device specifier as a (seemingly) unique device identifier.
However the very same BDF number can be used on another PCI segment,
which makes the driver fail probing:
[ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003)
[ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700'
....
[ 27.684858] libphy: mii_bus r8169-700 failed to register
[ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22
Add the segment number to the device name to make it more unique.
This fixes operation on ARM N1SDP boards, with two boards connected
together to form an SMP system, and all on-board devices showing up
twice, just on different PCI segments. A similar issue would occur on
large systems with many PCI slots and multiple RTL8169 NICs.
Fixes: f1e911d5d0dfd ("r8169: add basic phylib support")
Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com>
[Andre: expand commit message, use pci_domain_nr()]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbfd4506f962e7e6fff8f37f017154a3c3791264 ]
Currently, VF doesn't enable rx VLAN offload when initializating,
and PF does it for VFs. If user disable the rx VLAN offload for
VF with ethtool -K, and reload the VF driver, it may cause the
rx VLAN offload state being inconsistent between hardware and
software.
Fixes it by enabling rx VLAN offload when VF initializing.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16f3299ae1aa3c327e1fb742d0379ae4d6e86f2 ]
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd93 ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11a39259ff79b74bc99f8b7c44075a2d6d5e7ab1 ]
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5ac ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cd657cb3ee6f4de57e635b126ffbe0e51d00f1a ]
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c9f046bc377efd1f5e26e74817d5f96e9506c86 ]
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830fd ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa46dffff452f7c6d907c4e6a0062e2c53a87fc0 ]
We call bnxt_ulp_stop() to notify the RDMA driver that some error or
imminent reset is about to happen. After that we always call
some variants of bnxt_close().
In the next patch, we will integrate the recently added error
recovery with the RDMA driver. In response to ulp_stop, the
RDMA driver may free MSIX vectors and that will also trigger
bnxt_close(). To avoid bnxt_close() from being called twice,
we set a new flag after ulp_stop is called. If the RDMA driver
frees MSIX vectors while the new flag is set, we will not call
bnxt_close(), knowing that it will happen in due course.
With this change, we must make sure that the bnxt_close() call
after ulp_stop will reset IRQ. Modify bnxt_reset_task()
accordingly if we call ulp_stop.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e7efc2ce3d0789cd7c21b70ff00cd7838d382639 ]
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce2d ("liquidio: CN23XX register setup")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 015fe6fd29c4b9ac0f61b8c4455ef88e6018b9cc ]
IRQs are requested during driver's ndo_open() and then later
freed up in disable_interrupts() during driver unload.
A race exists where driver can set the CXGB4_FULL_INIT_DONE
flag in ndo_open() after the disable_interrupts() in driver
unload path checks it, and hence misses calling free_irq().
Fix by unregistering netdevice first and sync with driver's
ndo_open(). This ensures disable_interrupts() checks the flag
correctly and frees up the IRQs properly.
Fixes: b37987e8db5f ("cxgb4: Disable interrupts and napi before unregistering netdev")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2342ae10d1272d411a468a85a67647dd115b344f ]
If the 'register_netdev() call fails, we must release the resources
allocated by the previous 'gve_init_priv()' call, as already done in the
remove function.
Add a new label and the missing 'gve_teardown_priv_resources()' in the
error handling path.
Fixes: 893ce44df565 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 382a7c20d9253bcd5715789b8179528d0f3de72c ]
Assignment to *ring should be done after correctness check of the
argument queue.
Fixes: 91db364236c8 ("igb: Refactor igb_configure_cbs()")
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c19d772618fea40d9681f259368f284a330fd90 ]
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Fixes: 047e0030f1e6 ("igb: add new data structure for handling interrupts and NAPI")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Slawomir Laba <slawomirx.laba@intel.com>
Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Reviewed-by: Mateusz Palczewski <mateusz.placzewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af30cbd2f4d6d66a9b6094e0aa32420bc8b20e08 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 5eae00c57f5e ("i40evf: main driver core")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4589075608420bc49fcef6e98279324bf2bb91ae ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 111b9dc5c981 ("e1000e: add aer support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e85e14d68f517ef12a5fb8123fff65526b35b6cd ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 19ae1b3fb99c ("fm10k: Add support for PCI power management and error handling")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fea03b1cebd653cd095f2e9a58cfe1c85661c363 ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72ab ("igb: Add support for pci-e Advanced Error Reporting")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6bc9e5ce5d37cb3e6b552f41b92a193db1806ab ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: c9a11c23ceb6 ("igc: Add netdev")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faf4dd52e9e34a36254a6ad43369064b6928d504 ]
Use the pci_release_mem_regions method instead of the
pci_release_selected_regions method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2aefcd5e37989ae5f90afdae44bbbf3a2990da ]
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 6fabd715e6d8 ("ixgbe: Implement PCIe AER support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05682a0a61b6cbecd97a0f37f743b2cbfd516977 ]
Static analysis reports this problem
igc_main.c:4944:20: warning: The left operand of '&'
is a garbage value
if (!(phy_data & SR_1000T_REMOTE_RX_STATUS) &&
~~~~~~~~ ^
phy_data is set by the call to igc_read_phy_reg() only if
there is a read_reg() op, else it is unset and a 0 is
returned. Change the return to -EOPNOTSUPP.
Fixes: 208983f099d9 ("igc: Add watchdog")
Signed-off-by: Tom Rix <trix@redhat.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b292608db23ccbbfbfa50cdb155d01725d7a52e ]
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60f2 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reported-by: Erez Geva <erez.geva.ext@siemens.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit deb7178eb940e2c5caca1b1db084a69b2e59b4c9 upstream.
fp is netdev private data and it cannot be
used after free_netdev() call. Using fp after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() after error message.
Fixes: 61414f5ec983 ("FDDI: defza: Add support for DEC FDDIcontroller 700
TURBOchannel adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0336f8ffece62f882ab3012820965a786a983f70 upstream.
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 1e0a8b13d355 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad297cd2db8953e2202970e9504cab247b6c7cb4 upstream.
adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 54e19bc74f33 ("net: qcom/emac: do not use devm on internal phy pdev")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c78eaeebe855fd93f2e77142ffd0404a54070d84 upstream.
In case of netdev registration failure the code path will
jump to init_fail label:
init_fail:
netdev_err(ndev, "init failed\n");
moxart_mac_free_memory(ndev);
irq_map_fail:
free_netdev(ndev);
return ret;
So, there is no need to call free_netdev() before jumping
to error handling path, since it can cause UAF or double-free
bug.
Fixes: 6c821bd9edc9 ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b452550a203d88112eaf0ba9fc4b750a000b496 upstream.
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3709488790022c85720f991bff50d48ed5a36e6a upstream.
Commit 9e5baf9b36367 ("net: dsa: mv88e6xxx: add RMU disable op")
introduced .rmu_disable() method with implementation for several models,
but forgot to add Topaz, which can use the Peridot implementation.
Use the Peridot implementation of .rmu_disable() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 9e5baf9b36367 ("net: dsa: mv88e6xxx: add RMU disable op")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7da467d82d1ed4fb317aff836f99709169e73f10 upstream.
Commit f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
introduced .port_set_policy() method with implementation for several
models, but forgot to add Topaz, which can use the 6352 implementation.
Use the 6352 implementation of .port_set_policy() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5a2f966d0f3fa0ef6dada7ab9eda74cacee96b8a ]
It's unsafe to operate a vq from multiple threads.
Unfortunately this is exactly what we do when invoking
clean tx poll from rx napi.
Same happens with napi-tx even without the
opportunistic cleaning from the receive interrupt: that races
with processing the vq in start_xmit.
As a fix move everything that deals with the vq to under tx lock.
Fixes: b92f1e6751a6 ("virtio-net: transmit napi")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f2869cace829fb4b80fc53b3ddaa7f4ba9acbf1 ]
Do some cleanups in virtnet_restore() when virtnet_cpu_notif_add() failed.
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Link: https://lore.kernel.org/r/20210517084516.332-1-xieyongji@bytedance.com
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 35cba15a504bf4f585bb9d78f47b22b28a1a06b2 upstream.
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
[yyl: since devm_platform_get_and_ioremap_resource() is introduced
in linux-5.7, so just check the return value after calling
platform_get_resource()]
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ebe4feb8b442884f5a28d2437040096723dd1ea ]
If SRIOV cannot be disabled during device removal or module unloading,
return error code so it can be logged properly in the calling function.
Note that this can only happen if any VF is currently attached to a
guest using Xen, but not with vfio/KVM. Despite that in that case the
VFs won't work properly with PF removed and/or the module unloaded, I
have let it as is because I don't know what side effects may have
changing it, and also it seems to be the same that other drivers are
doing in this situation.
In the case of being called during SRIOV reconfiguration, the behavior
hasn't changed because the function is called with force=false.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45423cff1db66cf0993e8a9bd0ac93e740149e49 ]
If pci_remove was called for a PF with VFs, the removal of the VFs was
called twice from efx_ef10_sriov_fini: one directly with pci_driver->remove
and another implicit by calling pci_disable_sriov, which also perform
the VFs remove. This was leading to crashing the kernel on the second
attempt.
Given that pci_disable_sriov already calls to pci remove function, get
rid of the direct call to pci_driver->remove from the driver.
2 different ways to trigger the bug:
- Create one or more VFs, then attach the PF to a virtual machine (at
least with qemu/KVM)
- Create one or more VFs, then remove the PF with:
echo 1 > /sys/bus/pci/devices/PF_PCI_ID/remove
Removing sfc module does not trigger the error, at least for me, because
it removes the VF first, and then the PF.
Example of a log with the error:
list_del corruption, ffff967fd20a8ad0->next is LIST_POISON1 (dead000000000100)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:47!
[...trimmed...]
RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x4c
[...trimmed...]
Call Trace:
efx_dissociate+0x1f/0x140 [sfc]
efx_pci_remove+0x27/0x150 [sfc]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
pci_stop_bus_device+0x69/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pci_iov_remove_virtfn+0xba/0x120
sriov_disable+0x2f/0xe0
efx_ef10_pci_sriov_disable+0x52/0x80 [sfc]
? pcie_aer_is_native+0x12/0x40
efx_ef10_sriov_fini+0x72/0x110 [sfc]
efx_pci_remove+0x62/0x150 [sfc]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
unbind_store+0xf6/0x130
kernfs_fop_write+0x116/0x190
vfs_write+0xa5/0x1a0
ksys_write+0x4f/0xb0
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26d18c75a7496c4c52b0b6789e713dc76ebfbc87 ]
After firmware alive, iwl_trans_pcie_gen2_fw_alive() is called
to free the context info. However, on gen3 that will then free
the context info with the wrong size.
Since we free this allocation later, let it stick around until
the device is stopped for now, freeing some of it earlier is a
separate change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.afb63fb8cbc1.If4968db8e09f4ce2a1d27a6d750bca3d132d7d70@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 310f60f53a86eba680d9bc20a371e13b06a5f903 ]
In the case of gen3 devices with image loader (IML) support,
we were leaking the IML DMA allocation and never freeing it.
Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618105614.07e117dbedb7.I7bb9ebbe0617656986c2a598ea5e827b533bd3b9@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8835a64f74c46baebfc946cd5a2c861b866ebcee ]
When we have a P2P Device active, we attempt to only change the
PHY context it uses when we get a new remain-on-channel, if the
P2P Device is the only user of the PHY context.
This is fine if we're switching within a band, but if we're
switching bands then the switch implies a removal and re-add
of the PHY context, which isn't permitted by the firmware while
it's bound to an interface.
Fix the code to skip the unbind/release/... cycle only if the
band doesn't change (or we have old devices that can switch the
band on the fly as well.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.e9ac313f70f3.I713b9d109957df7e7d9ed0861d5377ce3f8fccd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c240b044edefa3c3af4014a4030e017dd95b59a1 ]
Based on 2001:3319 and 2357:0109 which I used to test the fix and
0bda:818b and 2357:0108 for which I found efuse dumps online.
== 2357:0109 ==
=== Before ===
Vendor: Realtek
Product: \x03802.11n NI
Serial:
=== After ===
Vendor: Realtek
Product: 802.11n NIC
Serial not available.
== 2001:3319 ==
=== Before ===
Vendor: Realtek
Product: Wireless N
Serial: no USB Adap
=== After ===
Vendor: Realtek
Product: Wireless N Nano USB Adapter
Serial not available.
Signed-off-by: Pascal Terjan <pterjan@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210424172959.1559890-1-pterjan@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec8f1a90d006f7cedcf86ef19fd034a406a213d6 ]
Rely on the txs fixed-rate bit instead of info->control.rates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd778f89225cd258e8f0fed2b7256124982c8bb5 ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1620788714-14300-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10a87a3535cce2b890897914f5d0d83df669c63 ]
Function wl1251_cmd_scan calls memcpy without checking the length.
Harden by checking the length is within the maximum allowed size.
Signed-off-by: Lee Gibson <leegib@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210428115508.25624-1-leegib@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11ef6bc846dcdce838f0b00c5f6a562c57e5d43b ]
At least on wl12xx, reading the MAC after boot can fail with a warning
at drivers/net/wireless/ti/wlcore/sdio.c:78 wl12xx_sdio_raw_read.
The failed call comes from wl12xx_get_mac() that wlcore_nvs_cb() calls
after request_firmware_work_func().
After the error, no wireless interface is created. Reloading the wl12xx
module makes the interface work.
Turns out the wlan controller can be in a low-power ELP state after the
boot from the bootloader or kexec, and needs to be woken up first.
Let's wake the hardware and add a sleep after that similar to
wl12xx_pre_boot() is already doing.
Note that a similar issue could exist for wl18xx, but I have not seen it
so far. And a search for wl18xx_get_mac and wl12xx_sdio_raw_read did not
produce similar errors.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210603062814.19464-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1ee8856de82faec9bc8bd0f2308a7f27e30ba207 ]
It has been reported that on RTL8106e the link-up interrupt may be
significantly delayed if the user enables ASPM L1. Per default ASPM
is disabled. The change leaves L1 enabled on the PCIe link (thus still
allowing to reach higher package power saving states), but the
NIC won't actively trigger it.
Reported-by: Koba Ko <koba.ko@canonical.com>
Tested-by: Koba Ko <koba.ko@canonical.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f18c11812c949553d2b2481ecaa274dd51bed1e7 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f1932e2282c58cb5ac59517585206cf5b385ae ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0bb51a3a385790a4be20085494cf78f70dadf646 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74325bf0104573c6dfce42837139aeef3f34be76 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
