IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 341abd693d10e5f337a51f140ae3e7a1ae0febf6 upstream.
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7f0909db761535aefafa77031062603a71557267 upstream.
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66ef ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898dc2 ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5227c51090e165db4b48dcaa300605bfced7014 upstream.
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c4a509d3815a260c423c0633bd73695250ac26d upstream.
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cc9ca4d95846cbbece48d9cd385550f8fba6a3c1 upstream.
The Tegra serial driver always prints an error message when enabling the
FIFO for devices that have support for checking the FIFO enable status.
Fix this by displaying the error message, only when an error occurs.
Finally, update the error message to make it clear that enabling the
FIFO failed and display the error code.
Fixes: 222dcdff3405 ("serial: tegra: check for FIFO mode enabled status")
Cc: <stable@vger.kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210630125643.264264-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d157fca711ad42e75efef3444c83d2e1a17be27a ]
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fad92b11047a748c996ebd6cfb164a63814eeb2e ]
In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.
Add a resource handling path to free this memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcb10ee27fb91b25b68d7745db9817ecea9f1038 ]
We should be very careful about the register values that will be used
for division or modulo operations, althrough the possibility that the
UARTBAUD register value is zero is very low, but we had better to deal
with the "bad data" of hardware in advance to avoid division or modulo
by zero leading to undefined kernel behavior.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210427021226.27468-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit deeaf963569a0d9d1b08babb771f61bb501a5704 ]
For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecd6b010d81f97b06b2f64d2d4f50ebf5acddaa9 ]
Testing mvuart->clk for non-error is not enough as mvuart->clk may contain
valid clk pointer but when clk_prepare_enable(mvuart->clk) failed then
port->uartclk is zero.
When mvuart->clk is not available then port->uartclk is zero too.
Parent clock rate port->uartclk is needed to calculate UART clock divisor
and without it is not possible to change baudrate.
So fix test condition when it is possible to change baudrate.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-3-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78bcae8616ac277d6cb7f38e211493948ed73e30 ]
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 11b1d881a90fc184cc7d06e9804eb288c24a2a0d upstream.
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08a84410a04f05c7c1b8e833f552416d8eb9f6fe upstream.
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3890e3dea315f1a257d1b940a2a4e2fa16a7b095 ]
The macro "spi_register_driver" invokes the function
"__spi_register_driver()" which has a return type of int and can fail,
returning a negative value in such a case. This is currently ignored and
the init() function yields success even if the spi driver failed to
register.
Fix this by collecting the return value of "__spi_register_driver()" and
also unregister the uart driver in case of failure.
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0a85abbe92e1a6f3e8580a4590fa7245de7090b ]
This reverts commit 51f689cc11333944c7a457f25ec75fcb41e99410.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This change did not properly unwind from the error condition, so it was
not correct.
Cc: Kangjie Lu <kjlu@umn.edu>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ea2e019c190ee3973ef7bcaf829d8762e56e635 upstream.
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f66d1b8 ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ddb4ce1e6e3bd112778ab93bbd9092f23a878ec upstream.
Currently the expression lsr | UART_LSR_TEMT is always true and
this seems suspect. I believe the intent was to mask lsr with UART_LSR_TEMT
to check that bit, so the expression should be using the & operator
instead. Fix this.
Fixes: b9c2470fb150 ("serial: tegra: flush the RX fifo on frame error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426105514.23268-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9808f9be31c68af43f6e531f2c851ebb066513fe upstream.
In commit 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0e24208792080135248f23fdf6d51aa2e04df05 upstream.
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e722b217ad3cf41f5504db80a68062df82b5242 upstream.
The commit that added this check did so in a very strange way - first
security_locked_down() is called, its value stored into retval, and if
it's nonzero, then an additional check is made for (change_irq ||
change_port), and if this is true, the function returns. However, if
the goto exit branch is not taken, the code keeps the retval value and
continues executing the function. Then, depending on whether
uport->ops->verify_port is set, the retval value may or may not be reset
to zero and eventually the error value from security_locked_down() may
abort the function a few lines below.
I will go out on a limb and assume that this isn't the intended behavior
and that an error value from security_locked_down() was supposed to
abort the function only in case (change_irq || change_port) is true.
Note that security_locked_down() should be called last in any series of
checks, since the SELinux implementation of this hook will do a check
against the policy and generate an audit record in case of denial. If
the operation was to carry on after calling security_locked_down(), then
the SELinux denial record would be bogus.
See commit 59438b46471a ("security,lockdown,selinux: implement SELinux
lockdown") for how SELinux implements this hook.
Fixes: 794edf30ee6c ("lockdown: Lock down TIOCSSERIAL")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210507115719.140799-1-omosnace@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 754f39158441f4c0d7a8255209dd9a939f08ce80 upstream.
This reverts commit 32f47179833b63de72427131169809065db6745e.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be not be needed at all as the
change was useless because this function can only be called when
of_match_device matched on something. So it should be reverted.
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Fixes: 32f47179833b ("serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference")
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 79c5966cec7b148199386ef9933c31b999379065 ]
Drivers can return -ENOIOCTLCMD when an ioctl is not recognised to tell
the upper layers to continue looking for a handler.
This is not the case for the RS485 and ISO7816 ioctls whose handlers
should return -ENOTTY directly in case a serial driver does not
implement the corresponding methods.
Fixes: a5f276f10ff7 ("serial_core: Handle TIOC[GS]RS485 ioctls.")
Fixes: ad8c0eaa0a41 ("tty/serial_core: add ISO7816 infrastructure")
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210407095208.31838-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3db1d52466dc11dca4e47ef12a6e6e97f846af62 ]
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-13-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f264c6f6aece81a9f8fbdf912b20bd3feb476a7a ]
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210304162308.8984-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 54ca955b5a4024e2ce0f206b03adb7109bc4da26 upstream.
Commit c685af1108d7 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108d7 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f1496a923b6ba16679074fe77100e1b53cdb880 ]
Setup the port uartclk in sifive_serial_probe() so that the base baud
rate is correctly printed during device probe instead of always showing
"0". I.e. the probe message is changed from
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 0) is a SiFive UART v0
to the correct:
38000000.serial: ttySIF0 at MMIO 0x38000000 (irq = 1,
base_baud = 115200) is a SiFive UART v0
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2f70e49ed860020f5abae4f7015018ebc10e1f0e upstream.
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d96f04d347e4011977abdbb4da5d8f303ebd26f8 upstream.
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 33f16855dcb973f745c51882d0e286601ff3be2b upstream.
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d2620 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c97f2a6fb3dfbfbbc88edc8ea62ef2b944e18849 upstream.
Prior to the commit that this one fixes, the FIFO size was derived from
the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following
formula:
TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1)
The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A
LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ
being equal to 4, and in the register description for LPUARTx_FIFO, it
shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011",
even though these registers read as "101" in reality.
And when LPUART on LS1021A was working, the "101" value did correspond
to "16 datawords", by applying the formula above, even though the
documentation is wrong again (!!!!) and says that "101" means 64 datawords
(hint: it doesn't).
So the "new" formula created by commit f77ebb241ce0 has all the premises
of being wrong for LS1021A, because it relied only on false data and no
actual experimentation.
Interestingly, in commit c2f448cff22a ("tty: serial: fsl_lpuart: add
LS1028A support"), Michael Walle applied a workaround to this by manually
setting the FIFO widths for LS1028A. It looks like the same values are
used by LS1021A as well, in fact.
When the driver thinks that it has a deeper FIFO than it really has,
getty (user space) output gets truncated.
Many thanks to Michael for pointing out where to look.
Fixes: f77ebb241ce0 ("tty: serial: fsl_lpuart: correct the FIFO depth size")
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com
Reviewed-by：Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c2f448cff22a7ed09281f02bde084b0ce3bc61ed upstream.
The LS1028A uses little endian register access and has a different FIFO
size encoding.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-4-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c5fc92622ed5531ff324b20f014e9e3092f0187 upstream.
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d27412 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 912ab37c798770f21b182d656937072b58553378 upstream.
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d4a ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 534cf755d9df99e214ddbe26b91cd4d81d2603e2 upstream.
Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:
| sysrq: Changing Loglevel
| sysrq: Loglevel set to 9
|
| ======================================================
| WARNING: possible circular locking dependency detected
| 5.9.0-rc7 #1 Not tainted
| ------------------------------------------------------
| systemd-journal/138 is trying to acquire lock:
| ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
|
| but task is already holding lock:
| ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
|
| which lock already depends on the new lock.
[...]
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock(&port_lock_key);
| lock(console_owner);
| lock(&port_lock_key);
| lock(console_owner);
|
| *** DEADLOCK ***
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9ca43d42ed8d5fd635d327a664ed1d8579eb2af upstream.
For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.
Commit ce734600545f ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).
As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.
So, fix the logic to detect QUP with versions 2.5 and above.
Fixes: ce734600545f ("tty: serial: qcom_geni_serial: Update the oversampling rate")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Paras Sharma <parashar@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 29788ab1d2bf26c130de8f44f9553ee78a27e8d5 upstream.
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0fb9342d06b0f667b915ba58bfefc030e534a218 ]
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac5887595b ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d31676a8d91dd18e08853efd1cb26961a38c6a6 ]
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42e11948ddf68b9f799cad8c0ddeab0a39da33e8 ]
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cf4df30a98175033e9849f7f16c46e96ba47f41 ]
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f19c3f6c8109b8bab000afd35580929958e087a9 ]
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbd7814bbd595061fcb6d6355d63f04179161cd ]
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
