IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit e72a55f2e5ddcfb3dce0701caf925ce435b87682 ]
When a read/write command is sent via ioctl to the kernel,
and the command fails, the actual error response of the emmc
is not sent to the user.
IOCTL read/write tests are carried out using commands
17 (Single BLock Read), 24 (Single Block Write),
18 (Multi Block Read), 25 (Multi Block Write)
The tests are carried out on a 64Gb emmc device. All of these
tests try to access an "out of range" sector address (0x09B2FFFF).
It is seen that without the patch the response received by the user
is not OUT_OF_RANGE error (R1 response 31st bit is not set) as per
JEDEC specification. After applying the patch proper response is seen.
This is because the function returns without copying the response to
the user in case of failure. This patch fixes the issue.
Hence, this memcpy is required whether we get an error response or not.
Therefor it is moved up from the current position up to immediately
after we have called mmc_wait_for_req().
The test code and the output of only the CMD17 is included in the
commit to limit the message length.
CMD17 (Test Code Snippet):
==========================
printf("Forming CMD%d\n", opt_idx);
/* single block read */
cmd.blksz = 512;
cmd.blocks = 1;
cmd.write_flag = 0;
cmd.opcode = 17;
//cmd.arg = atoi(argv[3]);
cmd.arg = 0x09B2FFFF;
/* Expecting response R1B */
cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
memset(data, 0, sizeof(__u8) * 512);
mmc_ioc_cmd_set_data(cmd, data);
printf("Sending CMD%d: ARG[0x%08x]\n", opt_idx, cmd.arg);
if(ioctl(fd, MMC_IOC_CMD, &cmd))
perror("Error");
printf("\nResponse: %08x\n", cmd.response[0]);
CMD17 (Output without patch):
=============================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 0x09B2FFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 00000000
(Incorrect response)
CMD17 (Output with patch):
==========================
test@test-LIVA-Z:~$ sudo ./mmc cmd_test /dev/mmcblk0 17
[sudo] password for test:
Entering the do_mmc_commands:Device: /dev/mmcblk0 nargs:4
Entering the do_mmc_commands:Device: /dev/mmcblk0 options[17, 09B2FFFF]
Forming CMD17
Sending CMD17: ARG[0x09b2ffff]
Error: Connection timed out
Response: 80000900
(Correct OUT_OF_ERROR response as per JEDEC specification)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/20210824191726.8296-1-nishadkamdar@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ac5e45291f3f0d699a721357380d4593bc2dcb3 ]
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66bad6ed2204fdb78a0a8fb89d824397106a5471 ]
At a couple of places, the return values of the non-void functions were
not getting checked. This was reported by the coverity tool. Modify the
code to check the return values of the same.
Addresses-Coverity: ("check_return")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-5-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee5165354d498e5bceb0b386e480ac84c5f8c28c ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3ff0189d3bc9c03845fe37472c140f0fefd0c79 ]
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Fixes: 3fc7eaef44db ("mmc: dw_mmc: Add external dma interface support")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081644.19353-2-tony@atomide.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25f8203b4be1937c4939bb98623e67dcfd7da4d1 ]
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 09247e110b2efce3a104e57e887c373e0a57a412 upstream.
While initializing an UHS-I SD card, the mmc core first tries to switch to
1.8V I/O voltage, before it continues to change the settings for the bus
speed mode.
However, the current behaviour in the mmc core is inconsistent and doesn't
conform to the SD spec. More precisely, an SD card that supports UHS-I must
set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
response. When switching to 1.8V I/O the mmc core correctly checks both of
the bits, but only the SD_OCR_S18R bit when changing the settings for bus
speed mode.
Rather than actually fixing the code to confirm to the SD spec, let's
deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
parts. This enables us to support UHS-I for SDSC cards (outside spec),
which is actually being supported by some existing SDSC cards. Moreover,
this fixes the inconsistent behaviour.
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
Cc: stable@vger.kernel.org
[Ulf: Rewrote commit message and comments to clarify the changes]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77347eda64ed5c9383961d1de9165f9d0b7d8df6 upstream.
It might be that something goes wrong during tuning so the MMC core will
immediately trigger a retune. In our case it was:
- we sent a tuning block
- there was an error so we need to send an abort cmd to the eMMC
- the abort cmd had a CRC error
- retune was set by the MMC core
This lead to a vicious circle causing a performance regression of 75%.
So, clear retuning flags before we enable retuning to start with a known
cleared state.
Reported-by Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624151616.38770-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0244847f9fc5e20df8b7483c8a4717fe0432d38 upstream.
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c74f ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c0bb3107703d2c58f7a0a7a2060bb57bc120326 upstream.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the SET_ROM_WAIT_STATES request which erroneously used
usb_rcvctrlpipe().
Fixes: 88095e7b473a ("mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210521133026.17296-1-johan@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b52f09080565030a530a784f1c9948a7f48ca3 upstream.
According to the eMMC Spec:
"When command queuing is enabled (CMDQ Mode En bit in CMDQ_MODE_EN
field is set to ‘1’) class 11 commands are the only method through
which data transfer tasks can be issued. Existing data transfer
commands, namely CMD18/CMD17 and CMD25/CMD24, are not supported when
command queuing is enabled."
which means if CMDQ is enabled, the FFU commands will not be supported.
To fix this issue, just simply disable CMDQ on the ioctl path, and
re-enable CMDQ once ioctl request is completed.
Tested-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 1e8e55b67030 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210504203209.361597-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2f9ae69e5267f53e89e296fccee291975a85f0eb ]
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210508020321.1677-1-thunder.leizhen@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 961470820021e6f9d74db4837bd6831a1a30341b ]
The sdhci_sprd_writew() was defined by never used in sdhci_ops:
drivers/mmc/host/sdhci-sprd.c:134:20: warning: unused function 'sdhci_sprd_writew'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210601095403.236007-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 103a5348c22c3fca8b96c735a9e353b8a0801842 upstream.
It has been reported that usage of memcpy() to/from an iomem mapping is invalid,
and a recent arm64 memcpy update [1] triggers a memory abort when dram-access-quirk
is used on the G12A/G12B platforms.
This adds a local sg_copy_to_buffer which makes usage of io versions of memcpy
when dram-access-quirk is enabled.
[1] 285133040e6c ("arm64: Import latest memcpy()/memmove() implementation")
Fixes: acdc8e71d9bb ("mmc: meson-gx: add dram-access-quirk")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210609150230.9291-1-narmstrong@baylibre.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1149a6c06ee094a6e62886b0c0e8e66967a728a upstream.
Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce668a ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17a17bf50612e6048a9975450cf1bd30f93815b5 upstream.
The mmc core uses a PM notifier to temporarily during system suspend, turn
off the card detection mechanism for removal/insertion of (e)MMC/SD/SDIO
cards. Additionally, the notifier may be used to remove an SDIO card
entirely, if a corresponding SDIO functional driver don't have the system
suspend/resume callbacks assigned. This behaviour has been around for a
very long time.
However, a recent bug report tells us there are problems with this
approach. More precisely, when receiving the PM_SUSPEND_PREPARE
notification, we may end up hanging on I/O to be completed, thus also
preventing the system from getting suspended.
In the end what happens, is that the cancel_delayed_work_sync() in
mmc_pm_notify() ends up waiting for mmc_rescan() to complete - and since
mmc_rescan() wants to claim the host, it needs to wait for the I/O to be
completed first.
Typically, this problem is triggered in Android, if there is ongoing I/O
while the user decides to suspend, resume and then suspend the system
again. This due to that after the resume, an mmc_rescan() work gets punted
to the workqueue, which job is to verify that the card remains inserted
after the system has resumed.
To fix this problem, userspace needs to become frozen to suspend the I/O,
prior to turning off the card detection mechanism. Therefore, let's drop
the PM notifiers for mmc subsystem altogether and rely on the card
detection to be turned off/on as a part of the system_freezable_wq, that we
are already using.
Moreover, to allow and SDIO card to be removed during system suspend, let's
manage this from a ->prepare() callback, assigned at the mmc_host_class
level. In this way, we can use the parent device (the mmc_host_class
device), to remove the card device that is the child, in the
device_prepare() phase.
Reported-by: Kiwoong Kim <kwmad.kim@samsung.com>
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210310152900.149380-1-ulf.hansson@linaro.org
Reviewed-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 917a5336f2c27928be270226ab374ed0cbf3805d upstream.
Some of SD cards sets permanent write protection bit in their CSD register,
due to lifespan or internal problem. To avoid unnecessary I/O write
operations, let's parse the bits in the CSD during initialization and mark
the card as read only for this case.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20210222083156.19158-1-sh043.lee@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 147186f531ae49c18b7a9091a2c40e83b3d95649 upstream.
A CMD11 is sent to the SD/SDIO card to start the voltage switch procedure
into 1.8V I/O. According to the SD spec a power cycle is needed of the
card, if it turns out that the CMD11 fails. Let's fix this, to allow a
retry of the initialization without the voltage switch, to succeed.
Note that, whether it makes sense to also retry with the voltage switch
after the power cycle is a bit more difficult to know. At this point, we
treat it like the CMD11 isn't supported and therefore we skip it when
retrying.
Signed-off-by: DooHyun Hwang <dh0421.hwang@samsung.com>
Link: https://lore.kernel.org/r/20210210045936.7809-1-dh0421.hwang@samsung.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97fce126e279690105ee15be652b465fd96f9997 upstream.
In command queueing mode, the cache isn't flushed via the mmc_flush_cache()
function, but instead by issuing a CMDQ_TASK_MGMT (CMD48) with a
FLUSH_CACHE opcode. In this path, we need to check if cache has been
enabled, before deciding to flush the cache, along the lines of what's
being done in mmc_flush_cache().
To fix this problem, let's add a new bus ops callback ->cache_enabled() and
implement it for the mmc bus type. In this way, the mmc block device driver
can call it to know whether cache flushing should be done.
Fixes: 1e8e55b67030 (mmc: block: Add CQE support)
Cc: stable@vger.kernel.org
Reported-by: Brendan Peter <bpeter@lytx.com>
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Tested-by: Brendan Peter <bpeter@lytx.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210425060207.2591-2-avri.altman@wdc.com
Link: https://lore.kernel.org/r/20210425060207.2591-3-avri.altman@wdc.com
[Ulf: Squashed the two patches and made some minor updates]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aea0440ad023ab0662299326f941214b0d7480bd upstream.
The cache function can be turned ON and OFF by writing to the CACHE_CTRL
byte (EXT_CSD byte [33]). However, card->ext_csd.cache_ctrl is only
set on init if cache size > 0.
Fix that by explicitly setting ext_csd.cache_ctrl on ext-csd write.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210420134641.57343-3-avri.altman@wdc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2970134b927834e9249659a70aac48e62dff804a upstream.
Bus power may control card power, but the full reset done by SDHCI at
initialization still may not reset the power, whereas a direct write to
SDHCI_POWER_CONTROL can. That might be needed to initialize correctly, if
the card was left powered on previously.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210331081752.23621-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21e35e898aa9ef7781632959db8613a5380f2eae upstream.
For data read commands, SDHC may initiate data transfers even before it
completely process the command response. In case command itself fails,
driver un-maps the memory associated with data transfer but this memory
can still be accessed by SDHC for the already initiated data transfer.
This scenario can lead to un-mapped memory access error.
To avoid this scenario, reset SDHC (when command fails) prior to
un-mapping memory. Resetting SDHC ensures that all in-flight data
transfers are either aborted or completed. So we don't run into this
scenario.
Swap the reset, un-map steps sequence in sdhci_request_done().
Suggested-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Signed-off-by: Pradeep P V K <pragalla@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1614760331-43499-1-git-send-email-pragalla@qti.qualcomm.com
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e29c84857e2d51aa017ce04284b962742fb97d9e upstream.
A 'tmio_mmc_host_free()' call is missing in the remove function, in order
to balance a 'tmio_mmc_host_alloc()' call in the probe.
This is done in the error handling path of the probe, but not in the remove
function.
Add the missing call.
Fixes: 3fd784f745dd ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142953.918608-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b03aec1c1f337dfdae44cdb0645ecac34208ae0a upstream.
A 'uniphier_sd_clk_enable()' call should be balanced by a corresponding
'uniphier_sd_clk_disable()' call.
This is done in the remove function, but not in the error handling path of
the probe.
Add the missing call.
Fixes: 3fd784f745dd ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20210220142935.918554-1-christophe.jaillet@wanadoo.fr
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0354ca6edd464a2cf332f390581977b8699ed081 ]
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f7dfda4f2cec580c135fd81d96a05006651c128 ]
The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so
set the quirk.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6052b3c370fb82dec28bcfff6d7ec0da84ac087a ]
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3c0 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9c256a8b0dc09c305c409d6264cc016af2ba38d ]
'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.
This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.
Fixes: fb8bd90f83c4 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f92e04f764b86e55e522988e6f4b6082d19a2721 upstream.
When analysing tuples fails we may loop indefinitely to retry. Let's avoid
this by using a 10s timeout and bail if not completed earlier.
Signed-off-by: Fengnan Chang <fengnanchang@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210123033230.36442-1-fengnanchang@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3ed0dc3594d99ff341ec63865a40519ea24b8d upstream.
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba881 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b503087445ce7e45fabdee87ca9e460d5b5b5168 upstream.
If extended CSD was not available, the eMMC driver would incorrectly
set the block size to 0, as the data_sector_size field of ext_csd
was never initialized. This issue was exposed by commit 817046ecddbc
("block: Align max_hw_sectors to logical blocksize") which caused
max_sectors and max_hw_sectors to be set to 0 after setting the block
size to 0, resulting in a kernel panic in bio_split when attempting
to read from the device. Fix it by only reading the block size from
ext_csd if it is available.
Fixes: a5075eb94837 ("mmc: block: Allow disabling 512B sector size emulation")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://linux-review.googlesource.com/id/If244d178da4d86b52034459438fec295b02d6e60
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210114201405.2934886-1-pcc@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6246d7c9d15aaff0bc3863f67900c6a6e6be921b upstream.
The CMD13 polling is needed for commands with R1B responses. In commit
a0d4c7eb71dd ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B
response"), the intent was to introduce this for requests targeted to the
RPMB partition. However, the condition to trigger the polling loop became
wrong, leading to unnecessary polling. Let's fix the condition to avoid
this.
Fixes: a0d4c7eb71dd ("mmc: block: Add CMD13 polling for MMC IOCTLS with R1B response")
Cc: stable@vger.kernel.org
Reported-by: Zhan Liu <zliua@micron.com>
Signed-off-by: Zhan Liu <zliua@micron.com>
Signed-off-by: Bean Huo <beanhuo@micron.com>
Link: https://lore.kernel.org/r/20201202202320.22165-1-huobean@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60d53566100abde4acc5504b524bc97f89015690 upstream.
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7d16e ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v5.4+
Link: https://lore.kernel.org/r/20201112133656.20317-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8973201d9b281375b5a8c66093de5679423021a upstream.
The commit 94b110aff867 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
added tmio_mmc_host_free(), but missed the function calling in
the sh_mobile_sdhi_remove() at that time. So, fix it. Otherwise,
we cannot rebind the sdhi/mmc devices when we use aliases of mmc.
Fixes: 94b110aff867 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1604654730-29914-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3e1ea16fb39fb6e1a1cf1dbdd6738531de3dc7d upstream.
sdhci-of-dwcmshc meets an eMMC read performance regression with below
command after commit 427b6514d095 ("mmc: sdhci: Add Auto CMD Auto
Select support"):
dd if=/dev/mmcblk0 of=/dev/null bs=8192 count=100000
Before the commit, the above command gives 120MB/s
After the commit, the above command gives 51.3 MB/s
So it looks like sdhci-of-dwcmshc expects Version 4 Mode for Auto
CMD Auto Select. Fix the performance degradation by ensuring v4_mode
is true to use Auto CMD Auto Select.
Fixes: 427b6514d095 ("mmc: sdhci: Add Auto CMD Auto Select support")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201015174115.4cf2c19a@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0add6e9b88d0632a25323aaf4987dbacb0e4ae64 upstream.
On rare occations there is the following error:
mmc0: Tuning timeout, falling back to fixed sampling clock
There are SD cards which takes a significant longer time to reply to the
first CMD19 command. The eSDHC takes the data timeout value into account
during the tuning period. The SDHCI core doesn't explicitly set this
timeout for the tuning procedure. Thus on the slow cards, there might be
a spurious "Buffer Read Ready" interrupt, which in turn triggers a wrong
sequence of events. In the end this will lead to an unsuccessful tuning
procedure and to the above error.
To workaround this, set the timeout to the maximum value (which is the
best we can do) and the SDHCI core will take care of the proper timeout
handling.
Fixes: ba49cbd0936e ("mmc: sdhci-of-esdhc: add tuning support")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201022222337.19857-1-michael@walle.cc
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f23cc3ba491af77395cea3f9d51204398729f26b upstream.
This change fixes HS400 tuning for devices with invalid presets.
SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are
used for DDR52. The HS400 retuning sequence is:
HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46f4a69ec8ed6ab9f6a6172afe50df792c8bc1b6 upstream.
Some Intel BYT based host controllers support the setting of latency
tolerance. Accordingly, implement the PM QoS ->set_latency_tolerance()
callback. The raw register values are also exposed via debugfs.
Intel EHL controllers require this support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: cb3a7d4a0aec4e ("mmc: sdhci-pci: Add support for Intel EHL")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200818104508.7149-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87d7ad089b318b4f319bf57f1daa64eb6d1d10ad ]
via_save_pcictrlreg() should be called with host->lock held
as it writes to pm_pcictrl_reg, otherwise there can be a race
condition between via_sd_suspend() and via_sdc_card_detect().
The same pattern is used in the function via_reset_pcictrl()
as well, where via_save_pcictrlreg() is called with host->lock
held.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200822061528.7035-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ebe2607965d3e2dc02029e8c7dd35fbe508ffd0 ]
Before parsing CISTPL_VERS_1 structure check that its size is at least two
bytes to prevent buffer overflow.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200727133837.19086-2-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
