IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 08d2061ff9c5319a07bf9ca6bbf11fdec68f704a ]
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.
With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.
Fixes: a7affb13b271 ("arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Ron Goossens <rgoossens@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211117140222.43692-1-robert.marko@sartura.hr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8240e87f16d17a9592c9d67857a3dcdbcb98f10d ]
As stated in the schematics [1] and [2] P5 the APIO5 domain is supplied
by RK808-D Buck4, which in our case vcc1v8_codec - i.e. a 1.8 V regulator.
Currently only white noise comes from the ES8316's output, which - for
whatever reason - came up only after the the correct switch from i2s0_8ch_bus
to i2s0_2ch_bus for i2s0's pinctrl was done.
Fix this by setting the correct regulator for audio-supply.
[1] https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi4_v13_sch_20181112.pdf
[2] https://dl.radxa.com/rockpi4/docs/hw/rockpi4/rockpi_4c_v12_sch_20200620.pdf
Fixes: 1b5715c602fd ("arm64: dts: rockchip: add ROCK Pi 4 DTS support")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20211027143726.165809-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b454a90e2ccdd6e03f88f930036da4df577be76 ]
Correct a typo in the vin-supply property. The input supply is
always-on, so this mistake doesn't affect whether the supply is actually
enabled correctly.
Fixes: fc702ed49a86 ("arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC")
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20211102182908.3409670-3-john@metanate.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 05abc6a5dec2a8c123a50235ecd1ad8d75ffa7b4 upstream.
Allow the SFP cages to be used with 2W SFP modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 715878016984b2617f6c1f177c50039e12e7bd5b upstream.
We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.
We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.
Commit f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.
So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.
We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14831fad73f5ac30ac61760487d95a538e6ab3cb upstream.
When running the following command without arm-linux-gnueabi-gcc in
one's $PATH, the following warning is observed:
$ ARCH=arm64 CROSS_COMPILE_COMPAT=arm-linux-gnueabi- make -j72 LLVM=1 mrproper
make[1]: arm-linux-gnueabi-gcc: No such file or directory
This is because KCONFIG is not run for mrproper, so CONFIG_CC_IS_CLANG
is not set, and we end up eagerly evaluating various variables that try
to invoke CC_COMPAT.
This is a similar problem to what was observed in
commit dc960bfeedb0 ("h8300: suppress error messages for 'make clean'")
Reported-by: Lucas Henneman <henneman@google.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211019223646.1146945-4-ndesaulniers@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99a7cacc66cae92db40139b57689be2af75fc6b8 ]
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f1dcaff642e75c1d2ad03f783fa8a3b1f56dd50 ]
The entry/exit latency and minimum residency in state for the idle
states of MSM8998 were ..bad: first of all, for all of them the
timings were written for CPU sleep but the min-residency-us param
was miscalculated (supposedly, while porting this from downstream);
Then, the power collapse states are setting PC on both the CPU
cluster *and* the L2 cache, which have different timings: in the
specific case of L2 the times are higher so these ones should be
taken into account instead of the CPU ones.
This parameter misconfiguration was not giving particular issues
because on MSM8998 there was no CPU scaling at all, so cluster/L2
power collapse was rarely (if ever) hit.
When CPU scaling is enabled, though, the wrong timings will produce
SoC unstability shown to the user as random, apparently error-less,
sudden reboots and/or lockups.
This set of parameters are stabilizing the SoC when CPU scaling is
ON and when power collapse is frequently hit.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210901183123.1087392-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 894d4f1f77d0e88f1f81af2e1e37333c1c41b631 ]
According to Documentation/devicetree/bindings/watchdog/arm,sp805.yaml
the compatible is:
compatible = "arm,sp805", "arm,primecell";
The current compatible string doesn't exist at all. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 812fa2f0e9d33564bd0131a69750e0d165f4c82a ]
Based on commit 65a2c14d4f00 ("dt-bindings: serial: convert Cadence UART
bindings to YAML") compatible string should look like differently that's
why fix it to be aligned with dt binding.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/89b36e0a6187cc6b05b27a035efdf79173bd4486.1628240307.git.michal.simek@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 167721a5909f867f8c18c8e78ea58e705ad9bbd4 ]
In kernel 5.4, support has been added for reading MTD devices via the nvmem
API.
For this the mtd devices are registered as read-only NVMEM providers under
sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are
identical then the second mtd device fails to get registered as a NVMEM
provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6c4b9b9232b93d9e316a63c086540fd5bf6b8687.1623684253.git.michal.simek@xilinx.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7c386fbc20262c1d911c615c65db6a58667d92c ]
gcc warns about undefined behavior the vmalloc code when building
with CONFIG_ARM64_PA_BITS_52, when the 'idx++' in the argument to
__phys_to_pte_val() is evaluated twice:
mm/vmalloc.c: In function 'vmap_pfn_apply':
mm/vmalloc.c:2800:58: error: operation on 'data->idx' may be undefined [-Werror=sequence-point]
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ~~~~~~~~~^~
arch/arm64/include/asm/pgtable-types.h:25:37: note: in definition of macro '__pte'
25 | #define __pte(x) ((pte_t) { (x) } )
| ^
arch/arm64/include/asm/pgtable.h:80:15: note: in expansion of macro '__phys_to_pte_val'
80 | __pte(__phys_to_pte_val((phys_addr_t)(pfn) << PAGE_SHIFT) | pgprot_val(prot))
| ^~~~~~~~~~~~~~~~~
mm/vmalloc.c:2800:30: note: in expansion of macro 'pfn_pte'
2800 | *pte = pte_mkspecial(pfn_pte(data->pfns[data->idx++], data->prot));
| ^~~~~~~
I have no idea why this never showed up earlier, but the safest
workaround appears to be changing those macros into inline functions
so the arguments get evaluated only once.
Cc: Matthew Wilcox <willy@infradead.org>
Fixes: 75387b92635e ("arm64: handle 52-bit physical addresses in page table entries")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211105075414.2553155-1-arnd@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 932b4610f55b49f3a158b0db451137bab7ed0e1f ]
As can be seen in RK3328's TRM the register range for the GPU is
0xff300000 to 0xff330000.
It would (and does in vendor kernel) overlap with the registers of
the HEVC encoder (node/driver do not exist yet in upstream kernel).
See already existing h265e_mmu node.
Fixes: 752fbc0c8da7 ("arm64: dts: rockchip: add rk3328 mali gpu node")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20210623115926.164861-1-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04fa4f03e3533f51b4db19cb487435f5862a0514 ]
The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.
The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f2dc2359b75e1fd345fd710862f73db20dc55864 ]
The SP805 binding sets the order of the clock-names to be: "wdog_clk",
"apb_pclk" (in exactly that order).
Change the order in the DTs for Freescale platforms to match that. The
two clocks given in all nodes are actually the same, so that does not
change any behaviour.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 514ef1e62d6521c2199d192b1c71b79d2aa21d5a upstream.
Current PCIe MEM space of size 16 MB is not enough for some combination
of PCIe cards (e.g. NVMe disk together with ath11k wifi card). ARM Trusted
Firmware for Armada 3700 platform already assigns 128 MB for PCIe window,
so extend PCIe MEM space to the end of 128 MB PCIe window which allows to
allocate more PCIe BARs for more PCIe cards.
Without this change some combination of PCIe cards cannot be used and
kernel show error messages in dmesg during initialization:
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:00:00.0: BAR 6: assigned [mem 0xe8000000-0xe80007ff pref]
pci 0000:01:00.0: BAR 8: no space for [mem size 0x01800000]
pci 0000:01:00.0: BAR 8: failed to assign [mem size 0x01800000]
pci 0000:02:03.0: BAR 8: no space for [mem size 0x01000000]
pci 0000:02:03.0: BAR 8: failed to assign [mem size 0x01000000]
pci 0000:02:07.0: BAR 8: no space for [mem size 0x00100000]
pci 0000:02:07.0: BAR 8: failed to assign [mem size 0x00100000]
pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit]
pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit]
Due to bugs in U-Boot port for Turris Mox, the second range in Turris Mox
kernel DTS file for PCIe must start at 16 MB offset. Otherwise U-Boot
crashes during loading of kernel DTB file. This bug is present only in
U-Boot code for Turris Mox and therefore other Armada 3700 devices are not
affected by this bug. Bug is fixed in U-Boot version 2021.07.
To not break booting new kernels on existing versions of U-Boot on Turris
Mox, use first 16 MB range for IO and second range with rest of PCIe window
for MEM.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 76f6386b25cc ("arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9fcb2e93f41c07a400885325e7dbdfceba6efaec ]
__stack_chk_guard is setup once while init stage and never changed
after that.
Although the modification of this variable at runtime will usually
cause the kernel to crash (so does the attacker), it should be marked
as __ro_after_init, and it should not affect performance if it is
placed in the ro_after_init section.
Signed-off-by: Dan Li <ashimida@linux.alibaba.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1631612642-102881-1-git-send-email-ashimida@linux.alibaba.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4b92d4add5f6dcf21275185c997d6ecb800054cd ]
DEFINE_SMP_CALL_CACHE_FUNCTION() was usefel before the CPU hotplug rework
to ensure that the cache related functions are called on the upcoming CPU
because the notifier itself could run on any online CPU.
The hotplug state machine guarantees that the callbacks are invoked on the
upcoming CPU. So there is no need to have this SMP function call
obfuscation. That indirection was missed when the hotplug notifiers were
converted.
This also solves the problem of ARM64 init_cache_level() invoking ACPI
functions which take a semaphore in that context. That's invalid as SMP
function calls run with interrupts disabled. Running it just from the
callback in context of the CPU hotplug thread solves this.
Fixes: 8571890e1513 ("arm64: Add support for ACPI based firmware tables")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://lore.kernel.org/r/871r69ersb.ffs@tglx
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e35ac9d0b56e9efefaeeb84b635ea26c2839ea86 upstream.
When we need a buffer for SVE register state we call sve_alloc() to make
sure that one is there. In order to avoid repeated allocations and frees
we keep the buffer around unless we change vector length and just memset()
it to ensure a clean register state. The function that deals with this
takes the task to operate on as an argument, however in the case where we
do a memset() we initialise using the SVE state size for the current task
rather than the task passed as an argument.
This is only an issue in the case where we are setting the register state
for a task via ptrace and the task being configured has a different vector
length to the task tracing it. In the case where the buffer is larger in
the traced process we will leak old state from the traced process to
itself, in the case where the buffer is smaller in the traced process we
will overflow the buffer and corrupt memory.
Fixes: bc0ee4760364 ("arm64/sve: Core task context handling")
Cc: <stable@vger.kernel.org> # 4.15.x
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210909165356.10675-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f865d0292ff3c0ca09414436510eb4c815815509 ]
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81210e38966cfa1c784364e4035081c3227cf5b ]
memory node like other node should be node@reg, which is missing in this
case, so fix it up
arch/arm64/boot/dts/qcom/ipq8074-hk01.dt.yaml: /: memory: False schema does not allow {'device_type': ['memory'], 'reg': [[0, 1073741824, 0, 536870912]]}
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210308060826.3074234-18-vkoul@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf2942a8b7c38e8cc2d5157b4f0323d7f4e5ec71 ]
The initialization sequence performed by the generic platform driver
pcie-designware-plat.c for a DWC based implementation doesn't work for
Tegra194. Tegra194 has a different initialization sequence requirement
which can only be satisfied by the Tegra194 specific platform driver
pcie-tegra194.c. So, remove the generic compatible string "snps,dw-pcie-ep"
from Tegra194's endpoint controller nodes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 90268574a3e8a6b883bd802d702a2738577e1006 upstream.
The `compute_indices` and `populate_entries` macros operate on inclusive
bounds, and thus the `map_memory` macro which uses them also operates
on inclusive bounds.
We pass `_end` and `_idmap_text_end` to `map_memory`, but these are
exclusive bounds, and if one of these is sufficiently aligned (as a
result of kernel configuration, physical placement, and KASLR), then:
* In `compute_indices`, the computed `iend` will be in the page/block *after*
the final byte of the intended mapping.
* In `populate_entries`, an unnecessary entry will be created at the end
of each level of table. At the leaf level, this entry will map up to
SWAPPER_BLOCK_SIZE bytes of physical addresses that we did not intend
to map.
As we may map up to SWAPPER_BLOCK_SIZE bytes more than intended, we may
violate the boot protocol and map physical address past the 2MiB-aligned
end address we are permitted to map. As we map these with Normal memory
attributes, this may result in further problems depending on what these
physical addresses correspond to.
The final entry at each level may require an additional table at that
level. As EARLY_ENTRIES() calculates an inclusive bound, we allocate
enough memory for this.
Avoid the extraneous mapping by having map_memory convert the exclusive
end address to an inclusive end address by subtracting one, and do
likewise in EARLY_ENTRIES() when calculating the number of required
tables. For clarity, comments are updated to more clearly document which
boundaries the macros operate on. For consistency with the other
macros, the comments in map_memory are also updated to describe `vstart`
and `vend` as virtual addresses.
Fixes: 0370b31e4845 ("arm64: Extend early page table code to allow for larger kernels")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210823101253.55567-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5e81d1117501546b7be050c5fbafa6efd2c722c upstream.
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[OP: - adjusted context for 5.4
- apply riscv changes to /arch/riscv/net/bpf_jit_comp.c]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 01c72cad790cb6cd3ccbe4c1402b6cb6c6bbffd0 ]
The GIC-400 CPU interfaces address range is defined as 0x2000-0x3FFF (by
ARM).
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Link: https://lore.kernel.org/r/20210805072110.4730-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ec82a7bb3db8c6005e715c63224c32d458917a2 ]
The "max-clock" and "min-vrefresh" properties fail to validate with
commit cfe34bb7a770c5d8 ("dt-bindings: drm: bridge: adi,adv7511.txt:
convert to yaml"). Drop them, as they are parts of an out-of-tree
workaround that is not needed upstream.
Fixes: bcf3003438ea4645 ("arm64: dts: renesas: r8a77995: draak: Enable HDMI display output")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/975b6686bc423421b147d367fe7fb9a0db99c5af.1625134398.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f890f89d9a80fffbfa7ca791b78927e5b8aba869 upstream.
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to
9134586715e3, 5f8d3ab136d0, which is needed to allow angler to boot after
3edfb7bd76bd ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac78d ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support")
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e30e8d46cf605d216a799a28c77b8a41c328613a upstream.
Due to inconsistencies in the way we manipulate compat GPRs, we have a
few issues today:
* For audit and tracing, where error codes are handled as a (native)
long, negative error codes are expected to be sign-extended to the
native 64-bits, or they may fail to be matched correctly. Thus a
syscall which fails with an error may erroneously be identified as
failing.
* For ptrace, *all* compat return values should be sign-extended for
consistency with 32-bit arm, but we currently only do this for
negative return codes.
* As we may transiently set the upper 32 bits of some compat GPRs while
in the kernel, these can be sampled by perf, which is somewhat
confusing. This means that where a syscall returns a pointer above 2G,
this will be sign-extended, but will not be mistaken for an error as
error codes are constrained to the inclusive range [-4096, -1] where
no user pointer can exist.
To fix all of these, we must consistently use helpers to get/set the
compat GPRs, ensuring that we never write the upper 32 bits of the
return code, and always sign-extend when reading the return code. This
patch does so, with the following changes:
* We re-organise syscall_get_return_value() to always sign-extend for
compat tasks, and reimplement syscall_get_error() atop. We update
syscall_trace_exit() to use syscall_get_return_value().
* We consistently use syscall_set_return_value() to set the return
value, ensureing the upper 32 bits are never set unexpectedly.
* As the core audit code currently uses regs_return_value() rather than
syscall_get_return_value(), we special-case this for
compat_user_mode(regs) such that this will do the right thing. Going
forward, we should try to move the core audit code over to
syscall_get_return_value().
Cc: <stable@vger.kernel.org>
Reported-by: He Zhe <zhe.he@windriver.com>
Reported-by: weiyuchen <weiyuchen3@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210802104200.21390-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
[Mark: trivial conflict resolution for v5.4.y]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77ec462536a13d4b428a1eead725c4818a49f0b1 upstream.
We can avoid the expensive ISB instruction after reading the counter in
the vDSO gettime functions by creating a fake address hazard against a
dummy stack read, just like we do inside the kernel.
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210318170738.7756-5-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
[ Upstream commit ee7ab3f263f8131722cff3871b9618b1e7478f07 ]
Some SFP modules are not detected when i2c-fast-mode is enabled even when
clock-frequency is already set to 100000. The I2C bus violates the timing
specifications when run in fast mode. So disable fast mode on Turris Mox.
Same change was already applied for uDPU (also Armada 3720 board with SFP)
in commit fe3ec631a77d ("arm64: dts: uDPU: remove i2c-fast-mode").
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e71b85473f863a29eb1c69265ef025389b4091d ]
U-Boot attempts to fix up the "clock-frequency" property of the "/sysclk" node:
https://elixir.bootlin.com/u-boot/v2021.04/source/arch/arm/cpu/armv8/fsl-layerscape/fdt.c#L512
but fails to do so:
## Booting kernel from Legacy Image at a1000000 ...
Image Name:
Created: 2021-06-08 10:31:38 UTC
Image Type: AArch64 Linux Kernel Image (gzip compressed)
Data Size: 15431370 Bytes = 14.7 MiB
Load Address: 80080000
Entry Point: 80080000
Verifying Checksum ... OK
## Flattened Device Tree blob at a0000000
Booting using the fdt blob at 0xa0000000
Uncompressing Kernel Image
Loading Device Tree to 00000000fbb19000, end 00000000fbb22717 ... OK
Unable to update property /sysclk:clock-frequency, err=FDT_ERR_NOTFOUND
Starting kernel ...
All Layerscape SoCs except LS1028A use "sysclk" as the node name, and
not "clock-sysclk". So change the node name of LS1028A accordingly.
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a52a48973b355b3aac5add92ef50650ae37c2bd ]
Move the turris-mox-rwtm firmware node from Turris MOX' device tree into
the generic armada-37xx.dtsi file and use the generic compatible string
'marvell,armada-3700-rwtm-firmware' instead of the current one.
Turris MOX DTS file contains also old compatible string for backward
compatibility.
The Turris MOX rWTM firmware can be used on any Armada 37xx device,
giving them access to the rWTM hardware random number generator, which
is otherwise unavailable.
This change allows Linux to load the turris-mox-rwtm.ko module on these
boards.
Tested on ESPRESSObin v5 with both default Marvell WTMI firmware and
CZ.NIC's firmware. With default WTMI firmware the turris-mox-rwtm fails
to probe, while with CZ.NIC's firmware it registers the HW random number
generator.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15a5261e4d052bf85c7fba24dbe0e9a7c8c05925 ]
This fixes multiple issues with the current non-existent PCIe clock setup:
The controller can run at up to 250MHz, so use a parent that provides this
clock.
The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.
The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8240c972c1798ea013cbb407722295fc826b3584 ]
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c33c ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70010556b158a0fefe43415fb0c58347dcce7da0 ]
The SCPI YAML schema expects standard node names for clocks and
power domain controllers. Fix those as per the schema for Juno
platforms.
Link: https://lore.kernel.org/r/20210608145133.2088631-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e6a282b49c6db408d27231e3c709fbdf25e3c1b ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-7-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5de0d688ac6e0202674577b05d0726b8a6af401 ]
Use more generic names (as recommended in the device tree specification
or the binding documentation)
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ecfad495f8af63a5cb332c91f60ab2018897f5 ]
A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.
Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9163f01130304fab1f74683d7d44632da7bda637 ]
When using CONFIG_ARM64_SW_TTBR0_PAN, a task's thread_info::ttbr0 must be
the TTBR0_EL1 value used to run userspace. With 52-bit PAs, the PA must be
packed into the TTBR using phys_to_ttbr(), but we forget to do this in some
of the SW PAN code. Thus, if the value is installed into TTBR0_EL1 (as may
happen in the uaccess routines), this could result in UNPREDICTABLE
behaviour.
Since hardware with 52-bit PA support almost certainly has HW PAN, which
will be used in preference, this shouldn't be a practical issue, but let's
fix this for consistency.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Fixes: 529c4b05a3cb ("arm64: handle 52-bit addresses in TTBR")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/1623749578-11231-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 833be850f1cabd0e3b5337c0fcab20a6e936dd48 ]
Depending on configuration options and specific code paths, we either
use the empty_zero_page or the configuration-dependent reserved_ttbr0
as a reserved value for TTBR{0,1}_EL1.
To simplify this code, let's always allocate and use the same
reserved_pg_dir, replacing reserved_ttbr0. Note that this is allocated
(and hence pre-zeroed), and is also marked as read-only in the kernel
Image mapping.
Keeping this separate from the empty_zero_page potentially helps with
robustness as the empty_zero_page is used in a number of cases where a
failure to map it read-only could allow it to become corrupted.
The (presently unused) swapper_pg_end symbol is also removed, and
comments are added wherever we rely on the offsets between the
pre-allocated pg_dirs to keep these cases easily identifiable.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201103102229.8542-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 311bea3cb9ee20ef150ca76fc60a592bf6b159f5 upstream.
With GNU binutils 2.35+, linking with BFD produces warnings for vmlinux:
aarch64-linux-gnu-ld: warning: -z norelro ignored
BFD can produce this warning when the target emulation mode does not
support RELRO program headers, and -z relro or -z norelro is passed.
Alan Modra clarifies:
The default linker emulation for an aarch64-linux ld.bfd is
-maarch64linux, the default for an aarch64-elf linker is
-maarch64elf. They are not equivalent. If you choose -maarch64elf
you get an emulation that doesn't support -z relro.
The ARCH=arm64 kernel prefers -maarch64elf, but may fall back to
-maarch64linux based on the toolchain configuration.
LLD will always create RELRO program header regardless of target
emulation.
To avoid the above warning when linking with BFD, pass -z norelro only
when linking with LLD or with -maarch64linux.
Fixes: 3b92fa7485eb ("arm64: link with -z norelro regardless of CONFIG_RELOCATABLE")
Fixes: 3bbd3db86470 ("arm64: relocatable: fix inconsistencies in linker script and options")
Cc: <stable@vger.kernel.org> # 5.0.x-
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Quentin Perret <qperret@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Alan Modra <amodra@gmail.com>
Cc: Fāng-ruì Sòng <maskray@google.com>
Link: https://lore.kernel.org/r/20201218002432.788499-1-ndesaulniers@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
