IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit cf0b0e3712f7af90006f8317ff27278094c2c128 upstream.
The POWER9 ERAT flush instruction is a SLBIA with IH=7, which is a
reserved value on POWER7/8. On POWER8 this invalidates the SLB entries
above index 0, similarly to SLBIA IH=0.
If the SLB entries are invalidated, and then the guest is bypassed, the
host SLB does not get re-loaded, so the bolted entries above 0 will be
lost. This can result in kernel stack access causing a SLB fault.
Kernel stack access causing a SLB fault was responsible for the infamous
mega bug (search "Fix SLB reload bug"). Although since commit
48e7b7695745 ("powerpc/64s/hash: Convert SLB miss handlers to C") that
starts using the kernel stack in the SLB miss handler, it might only
result in an infinite loop of SLB faults. In any case it's a bug.
Fix this by only executing the instruction on >= POWER9 where IH=7 is
defined not to invalidate the SLB. POWER7/8 don't require this ERAT
flush.
Fixes: 500871125920 ("KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211119031627.577853-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dae581864609d36fb58855fd59880b4941ce9d14 ]
kvmppc_h_set_dabr(), and kvmppc_h_set_xdabr() which jumps into
it, need to use _GLOBAL_TOC to setup the kernel TOC pointer, because
kvmppc_h_set_dabr() uses LOAD_REG_ADDR() to load dawr_force_enable.
When called from hcall_try_real_mode() we have the kernel TOC in r2,
established near the start of kvmppc_interrupt_hv(), so there is no
issue.
But they can also be called from kvmppc_pseries_do_hcall() which is
module code, so the access ends up happening with the kvm-hv module's
r2, which will not point at dawr_force_enable and could even cause a
fault.
With the current code layout and compilers we haven't observed a fault
in practice, the load hits somewhere in kvm-hv.ko and silently returns
some bogus value.
Note that we we expect p8/p9 guests to use the DAWR, but SLOF uses
h_set_dabr() to test if sc1 works correctly, see SLOF's
lib/libhvcall/brokensc1.c.
Fixes: c1fe190c0672 ("powerpc: Add force enable of DAWR on P9 option")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Link: https://lore.kernel.org/r/20210923151031.72408-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef071be57dc43679a32d5b0e6ee176d6f12e9f2 ]
In dcr-low.S we use cmpli with three arguments, instead of four
arguments as defined in the ISA:
cmpli cr0,r3,1024
This appears to be a PPC440-ism, looking at the "PPC440x5 CPU Core
User’s Manual" it shows cmpli having no L field, but implied to be 0 due
to the core being 32-bit. It mentions that the ISA defines four
arguments and recommends using cmplwi.
It also corresponds to the old POWER instruction set, which had no L
field there, a reserved bit instead.
dcr-low.S is only built 32-bit, because it is only built when
DCR_NATIVE=y, which is only selected by 40x and 44x. Looking at the
generated code (with gcc/gas) we see cmplwi as expected.
Although gas is happy with the 3-argument version when building for
32-bit, the LLVM assembler is not and errors out with:
arch/powerpc/sysdev/dcr-low.S:27:10: error: invalid operand for instruction
cmpli 0,%r3,1024; ...
^
Switch to the cmplwi extended opcode, which avoids any confusion when
reading the ISA, fixes the issue with the LLVM assembler, and also means
the code could be built 64-bit in future (though that's very unlikely).
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
BugLink: https://github.com/ClangBuiltLinux/linux/issues/1419
Link: https://lore.kernel.org/r/20211014024424.528848-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aed2886a5e9ffc8269a4220bff1e9e030d3d2eb1 ]
Fixes build warnings:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211013220532.24759-4-agust@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
upstream commit b7540d62509453263604a155bf2d5f0ed450cba2
Emit similar instruction sequences to commit a048a07d7f4535
("powerpc/64s: Add support for a store forwarding barrier at kernel
entry/exit") when encountering BPF_NOSPEC.
Mitigations are enabled depending on what the firmware advertises. In
particular, we do not gate these mitigations based on current settings,
just like in x86. Due to this, we don't need to take any action if
mitigations are enabled or disabled at runtime.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/956570cbc191cd41f8274bed48ee757a86dac62a.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
[adjust macros to account for commits 0654186510a40e, 3a181237916310 and ef909ba954145e.
adjust security feature checks to account for commit 84ed26fd00c514]
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
upstream commit 030905920f32e91a52794937f67434ac0b3ea41a
Add a helper to return the stf_barrier type for the current processor.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/3bd5d7f96ea1547991ac2ce3137dc2b220bae285.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
upstream commit 5855c4c1f415ca3ba1046e77c0b3d3dfc96c9025
We aren't handling subtraction involving an immediate value of
0x80000000 properly. Fix the same.
Fixes: 156d0e290e969c ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[mpe: Fold in fix from Naveen to use imm <= 32768]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/fc4b1276eb10761fd7ce0814c8dd089da2815251.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
[adjust macros to account for commits 0654186510a40e and 3a181237916310]
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
upstream commit 3832ba4e283d7052b783dab8311df7e3590fed93
Add checks to ensure that we never emit branch instructions with
truncated branch offsets.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/71d33a6b7603ec1013c9734dd8bdd4ff5e929142.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
[include header, drop ppc32 changes]
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
upstream commit 4549c3ea3160fa8b3f37dfe2f957657bb265eda9
Add a helper to check if a given offset is within the branch range for a
powerpc conditional branch instruction, and update some sites to use the
new helper.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/442b69a34ced32ca346a0d9a855f3f6cfdbbbd41.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 290fe8aa69ef5c51c778c0bb33f8ef0181c769f5 ]
Early exits from for_each_compatible_node() should decrement the
node reference counter. Reported by Coccinelle:
./arch/powerpc/platforms/44x/fsp2.c:206:1-25: WARNING: Function
"for_each_compatible_node" should have of_node_put() before return
around line 218.
Fixes: 7813043e1bbc ("powerpc/44x/fsp2: Add irq error handlers")
Signed-off-by: Bixuan Cui <cuibixuan@linux.alibaba.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1635406102-88719-1-git-send-email-cuibixuan@linux.alibaba.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3c2172c1c47b4079c29f0e6637d764a99355ebcd upstream.
When the field described in mpc85xx_smp_guts_ids[] is not configured in
dtb, the mpc85xx_setup_pmc() does not assign a value to the "guts"
variable. As a result, the oops is triggered when
mpc85xx_freeze_time_base() is executed.
Fixes: 56f1ba280719 ("powerpc/mpc85xx: refactor the PM operations")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210929033646.39630-2-nixiaoming@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8bbc9d822421d9ac8ff9ed26a3713c9afc69d6c8 upstream.
Only ignore the operation if dividing by 1.
Fixes: 156d0e290e969c ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c674ca18c3046885602caebb326213731c675d06.1633464148.git.naveen.n.rao@linux.vnet.ibm.com
[cascardo: use PPC_LI instead of EMIT(PPC_RAW_LI)]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 496c5fe25c377ddb7815c4ce8ecfb676f051e9b6 upstream.
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa9210 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c4726 ("powerpc: Add NAP mode support on
Power7 in HV mode").
Fixes: 9b4416c5095c ("KVM: PPC: Book3S HV: Fix stack handling in idle_kvm_start_guest()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211020094826.3222052-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdeb5d7d890e14f3b70e8087e745c4a6a7d9f337 upstream.
We call idle_kvm_start_guest() from power7_offline() if the thread has
been requested to enter KVM. We pass it the SRR1 value that was returned
from power7_idle_insn() which tells us what sort of wakeup we're
processing.
Depending on the SRR1 value we pass in, the KVM code might enter the
guest, or it might return to us to do some host action if the wakeup
requires it.
If idle_kvm_start_guest() is able to handle the wakeup, and enter the
guest it is supposed to indicate that by returning a zero SRR1 value to
us.
That was the behaviour prior to commit 10d91611f426 ("powerpc/64s:
Reimplement book3s idle code in C"), however in that commit the
handling of SRR1 was reworked, and the zeroing behaviour was lost.
Returning from idle_kvm_start_guest() without zeroing the SRR1 value can
confuse the host offline code, causing the guest to crash and other
weirdness.
Fixes: 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9b4416c5095c20e110c82ae602c254099b83b72f upstream.
In commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in
C") kvm_start_guest() became idle_kvm_start_guest(). The old code
allocated a stack frame on the emergency stack, but didn't use the
frame to store anything, and also didn't store anything in its caller's
frame.
idle_kvm_start_guest() on the other hand is written more like a normal C
function, it creates a frame on entry, and also stores CR/LR into its
callers frame (per the ABI). The problem is that there is no caller
frame on the emergency stack.
The emergency stack for a given CPU is allocated with:
paca_ptrs[i]->emergency_sp = alloc_stack(limit, i) + THREAD_SIZE;
So emergency_sp actually points to the first address above the emergency
stack allocation for a given CPU, we must not store above it without
first decrementing it to create a frame. This is different to the
regular kernel stack, paca->kstack, which is initialised to point at an
initial frame that is ready to use.
idle_kvm_start_guest() stores the backchain, CR and LR all of which
write outside the allocation for the emergency stack. It then creates a
stack frame and saves the non-volatile registers. Unfortunately the
frame it creates is not large enough to fit the non-volatiles, and so
the saving of the non-volatile registers also writes outside the
emergency stack allocation.
The end result is that we corrupt whatever is at 0-24 bytes, and 112-248
bytes above the emergency stack allocation.
In practice this has gone unnoticed because the memory immediately above
the emergency stack happens to be used for other stack allocations,
either another CPUs mc_emergency_sp or an IRQ stack. See the order of
calls to irqstack_early_init() and emergency_stack_init().
The low addresses of another stack are the top of that stack, and so are
only used if that stack is under extreme pressue, which essentially
never happens in practice - and if it did there's a high likelyhood we'd
crash due to that stack overflowing.
Still, we shouldn't be corrupting someone else's stack, and it is purely
luck that we aren't corrupting something else.
To fix it we save CR/LR into the caller's frame using the existing r1 on
entry, we then create a SWITCH_FRAME_SIZE frame (which has space for
pt_regs) on the emergency stack with the backchain pointing to the
existing stack, and then finally we switch to the new frame on the
emergency stack.
Fixes: 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in C")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211015133929.832061-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 73287caa9210ded6066833195f4335f7f688a46b upstream.
The idle entry/exit code saves/restores GPRs in the stack "red zone"
(Protected Zone according to PowerPC64 ELF ABI v2). However, the offset
used for the first GPR is incorrect and overwrites the back chain - the
Protected Zone actually starts below the current SP. In practice this is
probably not an issue, but it's still incorrect so fix it.
Also expand the comments to explain why using the stack "red zone"
instead of creating a new stackframe is appropriate here.
Signed-off-by: Christopher M. Riedl <cmr@codefail.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210206072342.5067-1-cmr@codefail.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f779e1d359b8d5801f677c1d49dcfa10bf95674 upstream.
When an interrupt is passed through, the KVM XIVE device calls the
set_vcpu_affinity() handler which raises the P bit to mask the
interrupt and to catch any in-flight interrupts while routing the
interrupt to the guest.
On the guest side, drivers (like some Intels) can request at probe
time some MSIs and call synchronize_irq() to check that there are no
in flight interrupts. This will call the XIVE get_irqchip_state()
handler which will always return true as the interrupt P bit has been
set on the host side and lock the CPU in an infinite loop.
Fix that by discarding disabled interrupts in get_irqchip_state().
Fixes: da15c03b047d ("powerpc/xive: Implement get_irqchip_state method for XIVE to fix shutdown race")
Cc: stable@vger.kernel.org #v5.4+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: seeteena <s1seetee@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20211011070203.99726-1-clg@kaod.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eed183abc0d3b8adb64fd1363b7cea7986cd58d6 ]
Property phy-connection-type contains invalid value "sgmii-2500" per scheme
defined in file ethernet-controller.yaml.
Correct phy-connection-type value should be "2500base-x".
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 84e0f1c13806 ("powerpc/mpc85xx: Add MDIO bus muxing support to the board device tree(s)")
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 267cdfa21385d78c794768233678756e32b39ead upstream.
POWER9 DD2.2 and 2.3 hardware implements a "fake-suspend" mode where
certain TM instructions executed in HV=0 mode cause softpatch interrupts
so the hypervisor can emulate them and prevent problematic processor
conditions. In this fake-suspend mode, the treclaim. instruction does
not modify registers.
Unfortunately the rfscv instruction executed by the guest do not
generate softpatch interrupts, which can cause the hypervisor to lose
track of the fake-suspend mode, and it can execute this treclaim. while
not in fake-suspend mode. This modifies GPRs and crashes the hypervisor.
It's not trivial to disable scv in the guest with HFSCR now, because
they assume a POWER9 has scv available. So this fix saves and restores
checkpointed registers across the treclaim.
Fixes: 7854f7545bff ("KVM: PPC: Book3S: Rework TM save/restore code and make it C-callable")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210908101718.118522-2-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1d78dfde33a02da1d816279c2e3452978b7abd39 ]
Since commit e1a1ef84cd07 ("KVM: PPC: Book3S: Allocate guest TCEs on
demand too"), pages for TCE tables for KVM guests are allocated only
when needed. This allows skipping any update when clearing TCEs. This
works mostly fine as TCE updates are handled when the MMU is enabled.
The realmode handlers fail with H_TOO_HARD when pages are not yet
allocated, except when clearing a TCE in which case KVM prints a warning
and proceeds to dereference a NULL pointer, which crashes the host OS.
This has not been caught so far as the change in commit e1a1ef84cd07 is
reasonably new, and POWER9 runs mostly radix which does not use realmode
handlers. With hash, the default TCE table is memset() by QEMU when the
machine is reset which triggers page faults and the KVM TCE device's
kvm_spapr_tce_fault() handles those with MMU on. And the huge DMA
windows are not cleared by VMs which instead successfully create a DMA
window big enough to map the VM memory 1:1 and then VMs just map
everything without clearing.
This started crashing now as commit 381ceda88c4c ("powerpc/pseries/iommu:
Make use of DDW for indirect mapping") added a mode when a dymanic DMA
window not big enough to map the VM memory 1:1 but it is used anyway,
and the VM now is the first (i.e. not QEMU) to clear a just created
table. Note that upstream QEMU needs to be modified to trigger the VM to
trigger the host OS crash.
This replaces WARN_ON_ONCE_RM() with a check and return, and adds
another warning if TCE is not being cleared.
Fixes: e1a1ef84cd07 ("KVM: PPC: Book3S: Allocate guest TCEs on demand too")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210827040706.517652-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1782663897945a5cf28e564ba5eed730098e9aa4 ]
After the L1 saves its PMU SPRs but before loading the L2's PMU SPRs,
switch the pmcregs_in_use field in the L1 lppaca to the value advertised
by the L2 in its VPA. On the way out of the L2, set it back after saving
the L2 PMU registers (if they were in-use).
This transfers the PMU liveness indication between the L1 and L2 at the
points where the registers are not live.
This fixes the nested HV bug for which a workaround was added to the L0
HV by commit 63279eeb7f93a ("KVM: PPC: Book3S HV: Always save guest pmu
for guest capable of nesting"), which explains the problem in detail.
That workaround is no longer required for guests that include this bug
fix.
Fixes: 360cae313702 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Link: https://lore.kernel.org/r/20210811160134.904987-10-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0e28a6145c3455b69991245e7f6147eb914b34a ]
CONFIG_MTD_PHYSMAP_OF is not longer enabled as it depends on
MTD_PHYSMAP which is not enabled.
This is a regression from commit 642b1e8dbed7 ("mtd: maps: Merge
physmap_of.c into physmap-core.c"), which added the extra dependency.
Add CONFIG_MTD_PHYSMAP=y so this stays in the config, as Christophe said
it is useful for build coverage.
Fixes: 642b1e8dbed7 ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210817045407.2445664-3-joel@jms.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6cae77f1bc89368a4e2822afcddc45c3062d499 ]
commit 7c6986ade69e ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
introduces udelay() call without including the linux/delay.h header.
This may happen to work on master but the header that declares the
functionshould be included nonetheless.
Fixes: 7c6986ade69e ("powerpc/stacktrace: Fix spurious "stale" traces in raise_backtrace_ipi()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729180103.15578-1-msuchanek@suse.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9addd85fbfacf0d155e83dbee8696d6df5ed0c7 upstream.
H_GetPerformanceCounterInfo (0xF080) hcall returns the counter data in
the result buffer. Result buffer has specific format defined in the PAPR
specification. One of the fields is counter offset and width of the
counter data returned.
Counter data are returned in a unsigned char array in big endian byte
order. To get the final counter data, the values must be left shifted
byte at a time. But commit 220a0c609ad17 ("powerpc/perf: Add support for
the hv gpci (get performance counter info) interface") made the shifting
bitwise and also assumed little endian order. Because of that, hcall
counters values are reported incorrectly.
In particular this can lead to counters go backwards which messes up the
counter prev vs now calculation and leads to huge counter value
reporting:
#: perf stat -e hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
-C 0 -I 1000
time counts unit events
1.000078854 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
2.000213293 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
3.000320107 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
4.000428392 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
5.000537864 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
6.000649087 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
7.000760312 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
8.000865218 16,448 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
9.000978985 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
10.001088891 16,384 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
11.001201435 0 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
12.001307937 18,446,744,073,709,535,232 hv_gpci/system_tlbie_count_and_time_tlbie_instructions_issued/
Fix the shifting logic to correct match the format, ie. read bytes in
big endian order.
Fixes: e4f226b1580b ("powerpc/perf/hv-gpci: Increase request buffer size")
Cc: stable@vger.kernel.org # v4.6+
Reported-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Tested-by: Nageswara R Sastry<rnsastry@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210813082158.429023-1-kjain@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5e81d1117501546b7be050c5fbafa6efd2c722c upstream.
In case of JITs, each of the JIT backends compiles the BPF nospec instruction
/either/ to a machine instruction which emits a speculation barrier /or/ to
/no/ machine instruction in case the underlying architecture is not affected
by Speculative Store Bypass or has different mitigations in place already.
This covers both x86 and (implicitly) arm64: In case of x86, we use 'lfence'
instruction for mitigation. In case of arm64, we rely on the firmware mitigation
as controlled via the ssbd kernel parameter. Whenever the mitigation is enabled,
it works for all of the kernel code with no need to provide any additional
instructions here (hence only comment in arm64 JIT). Other archs can follow
as needed. The BPF nospec instruction is specifically targeting Spectre v4
since i) we don't use a serialization barrier for the Spectre v1 case, and
ii) mitigation instructions for v1 and v4 might be different on some archs.
The BPF nospec is required for a future commit, where the BPF verifier does
annotate intermediate BPF programs with speculation barriers.
Co-developed-by: Piotr Krysiuk <piotras@gmail.com>
Co-developed-by: Benedict Schlueter <benedict.schlueter@rub.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Piotr Krysiuk <piotras@gmail.com>
Signed-off-by: Benedict Schlueter <benedict.schlueter@rub.de>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[OP: - adjusted context for 5.4
- apply riscv changes to /arch/riscv/net/bpf_jit_comp.c]
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 968339fad422a58312f67718691b717dac45c399 upstream.
.globl sets the symbol binding to STB_GLOBAL while .weak sets the
binding to STB_WEAK. GNU as let .weak override .globl since
binutils-gdb 5ca547dc2399a0a5d9f20626d4bf5547c3ccfddd (1996). Clang
integrated assembler let the last win but it may error in the future.
Since it is a convention that only one binding directive is used, just
delete .globl.
Fixes: ee9d21b3b358 ("powerpc/boot: Ensure _zimage_start is a weak symbol")
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200325164257.170229-1-maskray@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 333cf507465fbebb3727f5b53e77538467df312a upstream.
With commit c9f3401313a5 ("powerpc: Always enable queued spinlocks for
64s, disable for others") CONFIG_PPC_QUEUED_SPINLOCKS is always
enabled on ppc64le, external modules that use spinlock APIs are
failing.
ERROR: modpost: GPL-incompatible module XXX.ko uses GPL-only symbol 'shared_processor'
Before the above commit, modules were able to build without any
issues. Also this problem is not seen on other architectures. This
problem can be workaround if CONFIG_UNINLINE_SPIN_UNLOCK is enabled in
the config. However CONFIG_UNINLINE_SPIN_UNLOCK is not enabled by
default and only enabled in certain conditions like
CONFIG_DEBUG_SPINLOCKS is set in the kernel config.
#include <linux/module.h>
spinlock_t spLock;
static int __init spinlock_test_init(void)
{
spin_lock_init(&spLock);
spin_lock(&spLock);
spin_unlock(&spLock);
return 0;
}
static void __exit spinlock_test_exit(void)
{
printk("spinlock_test unloaded\n");
}
module_init(spinlock_test_init);
module_exit(spinlock_test_exit);
MODULE_DESCRIPTION ("spinlock_test");
MODULE_LICENSE ("non-GPL");
MODULE_AUTHOR ("Srikar Dronamraju");
Given that spin locks are one of the basic facilities for module code,
this effectively makes it impossible to build/load almost any non GPL
modules on ppc64le.
This was first reported at https://github.com/openzfs/zfs/issues/11172
Currently shared_processor is exported as GPL only symbol.
Fix this for parity with other architectures by exposing
shared_processor to non-GPL modules too.
Fixes: 14c73bd344da ("powerpc/vcpu: Assume dedicated processors as non-preempt")
Cc: stable@vger.kernel.org # v5.5+
Reported-by: marc.c.dionne@gmail.com
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210729060449.292780-1-srikar@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d9c57d3ed52a92536f5fa59dc5ccdd58b4875076 upstream.
The H_ENTER_NESTED hypercall is handled by the L0, and it is a request
by the L1 to switch the context of the vCPU over to that of its L2
guest, and return with an interrupt indication. The L1 is responsible
for switching some registers to guest context, and the L0 switches
others (including all the hypervisor privileged state).
If the L2 MSR has TM active, then the L1 is responsible for
recheckpointing the L2 TM state. Then the L1 exits to L0 via the
H_ENTER_NESTED hcall, and the L0 saves the TM state as part of the exit,
and then it recheckpoints the TM state as part of the nested entry and
finally HRFIDs into the L2 with TM active MSR. Not efficient, but about
the simplest approach for something that's horrendously complicated.
Problems arise if the L1 exits to the L0 with a TM state which does not
match the L2 TM state being requested. For example if the L1 is
transactional but the L2 MSR is non-transactional, or vice versa. The
L0's HRFID can take a TM Bad Thing interrupt and crash.
Fix this by disallowing H_ENTER_NESTED in TM[T] state entirely, and then
ensuring that if the L1 is suspended then the L2 must have TM active,
and if the L1 is not suspended then the L2 must not have TM active.
Fixes: 360cae313702 ("KVM: PPC: Book3S HV: Nested guest entry via hypercall")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f62f3c20647ebd5fb6ecb8f0b477b9281c44c10a upstream.
The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.
Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].
Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.
Fixes: 8e591cb72047 ("KVM: PPC: Book3S: Add infrastructure to implement kernel-side RTAS calls")
Cc: stable@vger.kernel.org # v3.10+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc4188a2f56e821ea057aca6bf444e138d06c252 ]
vcpu_put is not called if the user copy fails. This can result in preempt
notifier corruption and crashes, among other issues.
Fixes: b3cebfe8c1ca ("KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210716024310.164448-2-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd31ecf44b8e18ccb1e5f6b50f85de6922a60de3 ]
When running CPU_FTR_P9_TM_HV_ASSIST, HFSCR[TM] is set for the guest
even if the host has CONFIG_TRANSACTIONAL_MEM=n, which causes it to be
unprepared to handle guest exits while transactional.
Normal guests don't have a problem because the HTM capability will not
be advertised, but a rogue or buggy one could crash the host.
Fixes: 4bb3c7a0208f ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210716024310.164448-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9733862e50fdba55e7f1554e4286fcc5302ff28e ]
Commit f959dcd6ddfd29235030e8026471ac1b022ad2b0 (dma-direct: Fix
potential NULL pointer dereference) added a null check on the
dma_mask pointer of the kernel's device structure.
Add a dma_mask variable to the ps3_dma_region structure and set
the device structure's dma_mask pointer to point to this new variable.
Fixes runtime errors like these:
# WARNING: Fixes tag on line 10 doesn't match correct format
# WARNING: Fixes tag on line 10 doesn't match correct format
ps3_system_bus_match:349: dev=8.0(sb_01), drv=8.0(ps3flash): match
WARNING: CPU: 0 PID: 1 at kernel/dma/mapping.c:151 .dma_map_page_attrs+0x34/0x1e0
ps3flash sb_01: ps3stor_setup:193: map DMA region failed
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/562d0c9ea0100a30c3b186bcc7adb34b0bbd2cd7.1622746428.git.geoff@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 015d98149b326e0f1f02e44413112ca8b4330543 upstream.
A change in clang 13 results in the __lwsync macro being defined as
__builtin_ppc_lwsync, which emits 'lwsync' or 'msync' depending on what
the target supports. This breaks the build because of -Werror in
arch/powerpc, along with thousands of warnings:
In file included from arch/powerpc/kernel/pmc.c:12:
In file included from include/linux/bug.h:5:
In file included from arch/powerpc/include/asm/bug.h:109:
In file included from include/asm-generic/bug.h:20:
In file included from include/linux/kernel.h:12:
In file included from include/linux/bitops.h:32:
In file included from arch/powerpc/include/asm/bitops.h:62:
arch/powerpc/include/asm/barrier.h:49:9: error: '__lwsync' macro redefined [-Werror,-Wmacro-redefined]
#define __lwsync() __asm__ __volatile__ (stringify_in_c(LWSYNC) : : :"memory")
^
<built-in>:308:9: note: previous definition is here
#define __lwsync __builtin_ppc_lwsync
^
1 error generated.
Undefine this macro so that the runtime patching introduced by
commit 2d1b2027626d ("powerpc: Fixup lwsync at runtime") continues to
work properly with clang and the build no longer breaks.
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1386
Link: 62b5df7fe2
Link: https://lore.kernel.org/r/20210528182752.1852002-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd5d5e602f502895e47e18cd46804d6d7014e65c upstream.
The powerpc kernel is not prepared to handle exec faults from kernel.
Especially, the function is_exec_fault() will return 'false' when an
exec fault is taken by kernel, because the check is based on reading
current->thread.regs->trap which contains the trap from user.
For instance, when provoking a LKDTM EXEC_USERSPACE test,
current->thread.regs->trap is set to SYSCALL trap (0xc00), and
the fault taken by the kernel is not seen as an exec fault by
set_access_flags_filter().
Commit d7df2443cd5f ("powerpc/mm: Fix spurious segfaults on radix
with autonuma") made it clear and handled it properly. But later on
commit d3ca587404b3 ("powerpc/mm: Fix reporting of kernel execute
faults") removed that handling, introducing test based on error_code.
And here is the problem, because on the 603 all upper bits of SRR1
get cleared when the TLB instruction miss handler bails out to ISI.
Until commit cbd7e6ca0210 ("powerpc/fault: Avoid heavy
search_exception_tables() verification"), an exec fault from kernel
at a userspace address was indirectly caught by the lack of entry for
that address in the exception tables. But after that commit the
kernel mainly relies on KUAP or on core mm handling to catch wrong
user accesses. Here the access is not wrong, so mm handles it.
It is a minor fault because PAGE_EXEC is not set,
set_access_flags_filter() should set PAGE_EXEC and voila.
But as is_exec_fault() returns false as explained in the beginning,
set_access_flags_filter() bails out without setting PAGE_EXEC flag,
which leads to a forever minor exec fault.
As the kernel is not prepared to handle such exec faults, the thing to
do is to fire in bad_kernel_fault() for any exec fault taken by the
kernel, as it was prior to commit d3ca587404b3.
Fixes: d3ca587404b3 ("powerpc/mm: Fix reporting of kernel execute faults")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/024bb05105050f704743a0083fe3548702be5706.1625138205.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bab26238bbd44d5a4687c0a64fd2c7f2755ea937 ]
printk_safe_flush_on_panic() has special lock breaking code for the case
where we panic()ed with the console lock held. It relies on panic IPI
causing other CPUs to mark themselves offline.
Do as most other architectures do.
This effectively reverts commit de6e5d38417e ("powerpc: smp_send_stop do
not offline stopped CPUs"), unfortunately it may result in some false
positive warnings, but the alternative is more situations where we can
crash without getting messages out.
Fixes: de6e5d38417e ("powerpc: smp_send_stop do not offline stopped CPUs")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210623041245.865134-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77bbbc0cf84834ed130838f7ac1988567f4d0288 ]
The POWER9 vCPU TLB management code assumes all threads in a core share
a TLB, and that TLBIEL execued by one thread will invalidate TLBs for
all threads. This is not the case for SMT8 capable POWER9 and POWER10
(big core) processors, where the TLB is split between groups of threads.
This results in TLB multi-hits, random data corruption, etc.
Fix this by introducing cpu_first_tlb_thread_sibling etc., to determine
which siblings share TLBs, and use that in the guest TLB flushing code.
[npiggin@gmail.com: add changelog and comment]
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210602040441.3984352-1-npiggin@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c6986ade69e3c81bac831645bc72109cd798a80 upstream.
In raise_backtrace_ipi() we iterate through the cpumask of CPUs, sending
each an IPI asking them to do a backtrace, but we don't wait for the
backtrace to happen.
We then iterate through the CPU mask again, and if any CPU hasn't done
the backtrace and cleared itself from the mask, we print a trace on its
behalf, noting that the trace may be "stale".
This works well enough when a CPU is not responding, because in that
case it doesn't receive the IPI and the sending CPU is left to print the
trace. But when all CPUs are responding we are left with a race between
the sending and receiving CPUs, if the sending CPU wins the race then it
will erroneously print a trace.
This leads to spurious "stale" traces from the sending CPU, which can
then be interleaved messily with the receiving CPU, note the CPU
numbers, eg:
[ 1658.929157][ C7] rcu: Stack dump where RCU GP kthread last ran:
[ 1658.929223][ C7] Sending NMI from CPU 7 to CPUs 1:
[ 1658.929303][ C1] NMI backtrace for cpu 1
[ 1658.929303][ C7] CPU 1 didn't respond to backtrace IPI, inspecting paca.
[ 1658.929362][ C1] CPU: 1 PID: 325 Comm: kworker/1:1H Tainted: G W E 5.13.0-rc2+ #46
[ 1658.929405][ C7] irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 325 (kworker/1:1H)
[ 1658.929465][ C1] Workqueue: events_highpri test_work_fn [test_lockup]
[ 1658.929549][ C7] Back trace of paca->saved_r1 (0xc0000000057fb400) (possibly stale):
[ 1658.929592][ C1] NIP: c00000000002cf50 LR: c008000000820178 CTR: c00000000002cfa0
To fix it, change the logic so that the sending CPU waits 5s for the
receiving CPU to print its trace. If the receiving CPU prints its trace
successfully then the sending CPU just continues, avoiding any spurious
"stale" trace.
This has the added benefit of allowing all CPUs to print their traces in
order and avoids any interleaving of their output.
Fixes: 5cc05910f26e ("powerpc/64s: Wire up arch_trigger_cpumask_backtrace()")
Cc: stable@vger.kernel.org # v4.18+
Reported-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210625140408.3351173-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 51696f39cbee5bb684e7959c0c98b5f54548aa34 upstream.
LLVM does not emit optimal byteswap assembly, which results in high
stack usage in kvmhv_enter_nested_guest() due to the inlining of
byteswap_pt_regs(). With LLVM 12.0.0:
arch/powerpc/kvm/book3s_hv_nested.c:289:6: error: stack frame size of
2512 bytes in function 'kvmhv_enter_nested_guest' [-Werror,-Wframe-larger-than=]
long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
^
1 error generated.
While this gets fixed in LLVM, mark byteswap_pt_regs() as
noinline_for_stack so that it does not get inlined and break the build
due to -Werror by default in arch/powerpc/. Not inlining saves
approximately 800 bytes with LLVM 12.0.0:
arch/powerpc/kvm/book3s_hv_nested.c:290:6: warning: stack frame size of
1728 bytes in function 'kvmhv_enter_nested_guest' [-Wframe-larger-than=]
long kvmhv_enter_nested_guest(struct kvm_vcpu *vcpu)
^
1 warning generated.
Cc: stable@vger.kernel.org # v4.20+
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1292
Link: https://bugs.llvm.org/show_bug.cgi?id=49610
Link: https://lore.kernel.org/r/202104031853.vDT0Qjqj-lkp@intel.com/
Link: https://gist.github.com/ba710e3703bf45043a31e2806c843ffd
Link: https://lore.kernel.org/r/20210621182440.990242-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 19ae697a1e4edf1d755b413e3aa38da65e2db23b ]
The i2c controllers on the P1010 have an erratum where the documented
scheme for i2c bus recovery will not work (A-004447). A different
mechanism is needed which is documented in the P1010 Chip Errata Rev L.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7adc7b225cddcfd0f346d10144fd7a3d3d9f9ea7 ]
The i2c controllers on the P2040/P2041 have an erratum where the
documented scheme for i2c bus recovery will not work (A-004447). A
different mechanism is needed which is documented in the P2040 Chip
Errata Rev Q (latest available at the time of writing).
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aec86b052df6541cc97c5fca44e5934cbea4963b upstream.
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
sleeper[15639]: segfault (11) at c000000000004c20 nip c000000000004c20 lr c000000000004c20
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: f79643787e0a ("powerpc/64s: flush L1D on kernel entry")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-2-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec7791bae1327b1c279c5cd6e929c3b12daaf0a upstream.
The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
User access of kernel address (c00000003fff5af0) - exploit attempt? (uid: 0)
segfault (11) at c00000003fff5af0 nip 7fff8ad12198 lr 7fff8ad121f8 code 1
code: 40820128 e93c00d0 e9290058 7c292840 40810058 38600000 4bfd9a81 e8410018
code: 2c030006 41810154 3860ffb6 e9210098 <e94d8ff0> 7d295279 39400000 40820a3c
Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: a048a07d7f45 ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit")
Cc: stable@vger.kernel.org # v4.17+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc7130bf119add37f36238343a593b71ef6ecc1e ]
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock:
c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock:
c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(p->lock)/1);
lock(&(p->lock)/1);
===
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210301063653.51003-1-aik@ozlabs.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed8029d7b472369a010a1901358567ca3b6dbb0d ]
RCU complains about us calling printk() from an offline CPU:
=============================
WARNING: suspicious RCU usage
5.12.0-rc7-02874-g7cf90e481cb8 #1 Not tainted
-----------------------------
kernel/locking/lockdep.c:3568 RCU-list traversed in non-reader section!!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.12.0-rc7-02874-g7cf90e481cb8 #1
Call Trace:
dump_stack+0xec/0x144 (unreliable)
lockdep_rcu_suspicious+0x124/0x144
__lock_acquire+0x1098/0x28b0
lock_acquire+0x128/0x600
_raw_spin_lock_irqsave+0x6c/0xc0
down_trylock+0x2c/0x70
__down_trylock_console_sem+0x60/0x140
vprintk_emit+0x1a8/0x4b0
vprintk_func+0xcc/0x200
printk+0x40/0x54
pseries_cpu_offline_self+0xc0/0x120
arch_cpu_idle_dead+0x54/0x70
do_idle+0x174/0x4a0
cpu_startup_entry+0x38/0x40
rest_init+0x268/0x388
start_kernel+0x748/0x790
start_here_common+0x1c/0x614
Which happens because by the time we get to rtas_stop_self() we are
already offline. In addition the message can be spammy, and is not that
helpful for users, so remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210418135413.1204031-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 38d0b1c9cec71e6d0f3bddef0bbce41d05a3e796 ]
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
Fixes: 7340056567e3 ("powerpc/pci: Reorder pci bus/bridge unregistration during PHB removal")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210211182435.47968-1-tyreld@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
