IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 4ff2980b6bd2aa6b4ded3ce3b7c0ccfab29980af ]
in tunnel mode, if outer interface(ipv4) is less, it is easily to let
inner IPV6 mtu be less than 1280. If so, a Packet Too Big ICMPV6 message
is received. When send again, packets are fragmentized with 1280, they
are still rejected with ICMPV6(Packet Too Big) by xfrmi_xmit2().
According to RFC4213 Section3.2.2:
if (IPv4 path MTU - 20) is less than 1280
if packet is larger than 1280 bytes
Send ICMPv6 "packet too big" with MTU=1280
Drop packet
else
Encapsulate but do not set the Don't Fragment
flag in the IPv4 header. The resulting IPv4
packet might be fragmented by the IPv4 layer
on the encapsulator or by some router along
the IPv4 path.
endif
else
if packet is larger than (IPv4 path MTU - 20)
Send ICMPv6 "packet too big" with
MTU = (IPv4 path MTU - 20).
Drop packet.
else
Encapsulate and set the Don't Fragment flag
in the IPv4 header.
endif
endif
Packets should be fragmentized with ipv4 outer interface, so change it.
After it is fragemtized with ipv4, there will be double fragmenation.
No.48 & No.51 are ipv6 fragment packets, No.48 is double fragmentized,
then tunneled with IPv4(No.49& No.50), which obey spec. And received peer
cannot decrypt it rightly.
48 2002::10 2002::11 1296(length) IPv6 fragment (off=0 more=y ident=0xa20da5bc nxt=50)
49 0x0000 (0) 2002::10 2002::11 1304 IPv6 fragment (off=0 more=y ident=0x7448042c nxt=44)
50 0x0000 (0) 2002::10 2002::11 200 ESP (SPI=0x00035000)
51 2002::10 2002::11 180 Echo (ping) request
52 0x56dc 2002::10 2002::11 248 IPv6 fragment (off=1232 more=n ident=0xa20da5bc nxt=50)
xfrm6_noneed_fragment has fixed above issues. Finally, it acted like below:
1 0x6206 192.168.1.138 192.168.1.1 1316 Fragmented IP protocol (proto=Encap Security Payload 50, off=0, ID=6206) [Reassembled in #2]
2 0x6206 2002::10 2002::11 88 IPv6 fragment (off=0 more=y ident=0x1f440778 nxt=50)
3 0x0000 2002::10 2002::11 248 ICMPv6 Echo (ping) request
Signed-off-by: Lina Wang <lina.wang@mediatek.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 25666e8ccd952627899b09b68f7c9b68cfeaf028 ]
As of logitech lightspeed receiver fw version 04.02.B0009,
HIDPP_PARAM_DEVICE_INFO is being reported as 0x11.
With patch "HID: logitech-dj: add support for the new lightspeed receiver
iteration", the mouse starts to error out with:
logitech-djreceiver: unusable device of type UNKNOWN (0x011) connected on
slot 1
and becomes unusable.
This has been noticed on a Logitech G Pro X Superlight fw MPM 25.01.B0018.
Signed-off-by: Lucas Zampieri <lzampier@redhat.com>
Acked-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b37a466837393af72fe8bcb8f1436410f3f173f3 upstream.
Add the case if dev is NULL in dev_{put, hold}, so the caller doesn't
need to care whether dev is NULL or not.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e1d15646565b284e9ef2433234d6cfdaf66695f1 upstream.
IBM manufactures a PL2303 device for UPS communications. Add the vendor
and product IDs so that the PL2303 driver binds to the device.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220301224446.21236-1-eajames@linux.ibm.com
Cc: stable@vger.kernel.org
[ johan: amend the SoB chain ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ddbd89deb7d32b1fbb879f48d68fda1a8ac58e8e upstream.
The problem I'm addressing was discovered by the LTP test covering
cve-2018-1000204.
A short description of what happens follows:
1) The test case issues a command code 00 (TEST UNIT READY) via the SG_IO
interface with: dxfer_len == 524288, dxdfer_dir == SG_DXFER_FROM_DEV
and a corresponding dxferp. The peculiar thing about this is that TUR
is not reading from the device.
2) In sg_start_req() the invocation of blk_rq_map_user() effectively
bounces the user-space buffer. As if the device was to transfer into
it. Since commit a45b599ad808 ("scsi: sg: allocate with __GFP_ZERO in
sg_build_indirect()") we make sure this first bounce buffer is
allocated with GFP_ZERO.
3) For the rest of the story we keep ignoring that we have a TUR, so the
device won't touch the buffer we prepare as if the we had a
DMA_FROM_DEVICE type of situation. My setup uses a virtio-scsi device
and the buffer allocated by SG is mapped by the function
virtqueue_add_split() which uses DMA_FROM_DEVICE for the "in" sgs (here
scatter-gather and not scsi generics). This mapping involves bouncing
via the swiotlb (we need swiotlb to do virtio in protected guest like
s390 Secure Execution, or AMD SEV).
4) When the SCSI TUR is done, we first copy back the content of the second
(that is swiotlb) bounce buffer (which most likely contains some
previous IO data), to the first bounce buffer, which contains all
zeros. Then we copy back the content of the first bounce buffer to
the user-space buffer.
5) The test case detects that the buffer, which it zero-initialized,
ain't all zeros and fails.
One can argue that this is an swiotlb problem, because without swiotlb
we leak all zeros, and the swiotlb should be transparent in a sense that
it does not affect the outcome (if all other participants are well
behaved).
Copying the content of the original buffer into the swiotlb buffer is
the only way I can think of to make swiotlb transparent in such
scenarios. So let's do just that if in doubt, but allow the driver
to tell us that the whole mapped buffer is going to be overwritten,
in which case we can preserve the old behavior and avoid the performance
impact of the extra bounce.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8926d88ced46700bf6117ceaf391480b943ea9f4 upstream.
The get_user()/put_user() functions are meant to check for
access_ok(), while the __get_user()/__put_user() functions
don't.
This broke in 4.19 for nds32, when it gained an extraneous
check in __get_user(), but lost the check it needs in
__put_user().
Fixes: 487913ab18c2 ("nds32: Extract the checking and getting pointer to a macro")
Cc: stable@vger.kernel.org @ v4.19+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5abce6b2bb5cb3d628aaa63fa821da8c4600f9 upstream.
As part of the series conversion to remove nested TPM operations:
https://lore.kernel.org/all/20190205224723.19671-1-jarkko.sakkinen@linux.intel.com/
exposure of the chip->tpm_mutex was removed from much of the upper
level code. In this conversion, tpm2_del_space() was missed. This
didn't matter much because it's usually called closely after a
converted operation, so there's only a very tiny race window where the
chip can be removed before the space flushing is done which causes a
NULL deref on the mutex. However, there are reports of this window
being hit in practice, so fix this by converting tpm2_del_space() to
use tpm_try_get_ops(), which performs all the teardown checks before
acquring the mutex.
Cc: stable@vger.kernel.org # 5.4.x
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4a2d4496e15ea5bb5c8e83b94ca8ca7fb045e7d3 upstream.
While commit 6a01afcf8468 ("mac80211: mesh: Free ie data when leaving
mesh") fixed a memory leak on mesh leave / teardown it introduced a
potential memory corruption caused by a double free when rejoining the
mesh:
ieee80211_leave_mesh()
-> kfree(sdata->u.mesh.ie);
...
ieee80211_join_mesh()
-> copy_mesh_setup()
-> old_ie = ifmsh->ie;
-> kfree(old_ie);
This double free / kernel panics can be reproduced by using wpa_supplicant
with an encrypted mesh (if set up without encryption via "iw" then
ifmsh->ie is always NULL, which avoids this issue). And then calling:
$ iw dev mesh0 mesh leave
$ iw dev mesh0 mesh join my-mesh
Note that typically these commands are not used / working when using
wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going
through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join
where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of
default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids
the memory corruption, too.
The issue was first observed in an application which was not using
wpa_supplicant but "Senf" instead, which implements its own calls to
nl80211.
Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh
join function and leaving it solely up to the mesh leave to free the
mesh IE.
Cc: stable@vger.kernel.org
Fixes: 6a01afcf8468 ("mac80211: mesh: Free ie data when leaving mesh")
Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10c535787436d62ea28156a4b91365fd89b5a432 upstream.
Currently rcu_preempt_deferred_qs_irqrestore() releases rnp->boost_mtx
before reporting the expedited quiescent state. Under heavy real-time
load, this can result in this function being preempted before the
quiescent state is reported, which can in turn prevent the expedited grace
period from completing. Tim Murray reports that the resulting expedited
grace periods can take hundreds of milliseconds and even more than one
second, when they should normally complete in less than a millisecond.
This was fine given that there were no particular response-time
constraints for synchronize_rcu_expedited(), as it was designed
for throughput rather than latency. However, some users now need
sub-100-millisecond response-time constratints.
This patch therefore follows Neeraj's suggestion (seconded by Tim and
by Uladzislau Rezki) of simply reversing the two operations.
Reported-by: Tim Murray <timmurray@google.com>
Reported-by: Joel Fernandes <joelaf@google.com>
Reported-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Tested-by: Tim Murray <timmurray@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Sandeep Patil <sspatil@google.com>
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8893d27ffcaf6ec6267038a177cb87bcde4dd3de upstream.
The implementations of aead and skcipher in the QAT driver do not
support properly requests with the CRYPTO_TFM_REQ_MAY_BACKLOG flag set.
If the HW queue is full, the driver returns -EBUSY but does not enqueue
the request.
This can result in applications like dm-crypt waiting indefinitely for a
completion of a request that was never submitted to the hardware.
To avoid this problem, disable the registration of all crypto algorithms
in the QAT driver by setting the number of crypto instances to 0 at
configuration time.
Cc: stable@vger.kernel.org
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c844d22fe0c0b37dc809adbdde6ceb6462c43acf upstream.
Clevo NL5xRU and NL5xNU/TUXEDO Aura 15 Gen1 and Gen2 have both a working
native and video interface. However the default detection mechanism first
registers the video interface before unregistering it again and switching
to the native interface during boot. This results in a dangling SBIOS
request for backlight change for some reason, causing the backlight to
switch to ~2% once per boot on the first power cord connect or disconnect
event. Setting the native interface explicitly circumvents this buggy
behaviour by avoiding the unregistering process.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dacee0b9efc8bd061f097b1a8d4daa6591af0c6 upstream.
For some reason, the Microsoft Surface Go 3 uses the standard ACPI
interface for battery information, but does not use the standard PNP0C0A
HID. Instead it uses MSHW0146 as identifier. Add that ID to the driver
as this seems to work well.
Additionally, the power state is not updated immediately after the AC
has been (un-)plugged, so add the respective quirk for that.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e702196bf85778f2c5527ca47f33ef2e2fca8297 upstream.
On this board the ACPI RSDP structure points to both a RSDT and an XSDT,
but the XSDT points to a truncated FADT. This causes all sorts of trouble
and usually a complete failure to boot after the following error occurs:
ACPI Error: Unsupported address space: 0x20 (*/hwregs-*)
ACPI Error: AE_SUPPORT, Unable to initialize fixed events (*/evevent-*)
ACPI: Unable to start ACPI Interpreter
This leaves the ACPI implementation in such a broken state that subsequent
kernel subsystem initialisations go wrong, resulting in among others
mismapped PCI memory, SATA and USB enumeration failures, and freezes.
As this is an older embedded platform that will likely never see any BIOS
updates to address this issue and its default shipping OS only complies to
ACPI 1.0, work around this by forcing `acpi=rsdt`. This patch, applied on
top of Linux 5.10.102, was confirmed on real hardware to fix the issue.
Signed-off-by: Mark Cilissen <mark@yotsuba.nl>
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7557267c233b55d8e8d7ba4c68cf944fe2ec02c upstream.
ASUS GA402 requires a workaround to manage the routing of its 4 speakers
like the other ASUS models. Add a corresponding quirk entry to fix it.
Signed-off-by: Jason Zheng <jasonzheng2004@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220313092216.29858-1-jasonzheng2004@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 882bd07f564f97fca6e42ce6ce627ce24ce1ef5a upstream.
On a HP 288 Pro G8, the front mic could not be detected.In order to
get it working, the pin configuration needs to be set correctly, and
the ALC671_FIXUP_HP_HEADSET_MIC2 fixup needs to be applied.
Signed-off-by: huangwenhui <huangwenhuia@uniontech.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311093836.20754-1-huangwenhuia@uniontech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb6402c3c4a7c26d97c92d70186424097b6e366 upstream.
We've got syzbot reports hitting INT_MAX overflow at vmalloc()
allocation that is called from snd_pcm_plug_alloc(). Although we
apply the restrictions to input parameters, it's based only on the
hw_params of the underlying PCM device. Since the PCM OSS layer
allocates a temporary buffer for the data conversion, the size may
become unexpectedly large when more channels or higher rates is given;
in the reported case, it went over INT_MAX, hence it hits WARN_ON().
This patch is an attempt to avoid such an overflow and an allocation
for too large buffers. First off, it adds the limit of 1MB as the
upper bound for period bytes. This must be large enough for all use
cases, and we really don't want to handle a larger temporary buffer
than this size. The size check is performed at two places, where the
original period bytes is calculated and where the plugin buffer size
is calculated.
In addition, the driver uses array_size() and array3_size() for
multiplications to catch overflows for the converted period size and
buffer bytes.
Reported-by: syzbot+72732c532ac1454eeee9@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/00000000000085b1b305da5a66f3@google.com
Link: https://lore.kernel.org/r/20220318082036.29699-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455c5653f50e10b4f460ef24e99f0044fbe3401c upstream.
This is essentially a revert of the commit dc865fb9e7c2 ("ASoC: sti:
Use snd_pcm_stop_xrun() helper"), which converted the manual
snd_pcm_stop() calls with snd_pcm_stop_xrun().
The commit above introduced a deadlock as snd_pcm_stop_xrun() itself
takes the PCM stream lock while the caller already holds it. Since
the conversion was done only for consistency reason and the open-call
with snd_pcm_stop() to the XRUN state is a correct usage, let's revert
the commit back as the fix.
Fixes: dc865fb9e7c2 ("ASoC: sti: Use snd_pcm_stop_xrun() helper")
Reported-by: Daniel Palmer <daniel@0x0f.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220315091319.3351522-1-daniel@0x0f.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220315164158.19804-1-tiwai@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9e6faeafaa00da1851bcf47912b0f1acae666b4 upstream.
All packets on ingress (except for jumbo) are terminated with a 4-bytes
CRC checksum. It's the responsability of the driver to strip those 4
bytes. Unfortunately a change dating back to March 2017 re-shuffled some
code and made the CRC stripping code effectively dead.
This change re-orders that part a bit such that the datalen is
immediately altered if needed.
Fixes: 4902a92270fb ("drivers: net: xgene: Add workaround for errata 10GE_8/ENET_11")
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Tested-by: Stephane Graber <stgraber@ubuntu.com>
Link: https://lore.kernel.org/r/20220322224205.752795-1-stgraber@ubuntu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17aaf0193392cb3451bf0ac75ba396ec4cbded6e upstream.
Tests 72 and 78 for ALSA in kselftest fail due to reading
inconsistent values from some devices on a VirtualBox
Virtual Machine using the snd_intel8x0 driver for the AC'97
Audio Controller device.
Taking for example test number 72, this is what the test reports:
"Surround Playback Volume.0 expected 1 but read 0, is_volatile 0"
"Surround Playback Volume.1 expected 0 but read 1, is_volatile 0"
These errors repeat for each value from 0 to 31.
Taking a look at these error messages it is possible to notice
that the written values are read back swapped.
When the write is performed, these values are initially stored in
an array used to sanity-check them and write them in the pcmreg
array. To write them, the two one-byte values are packed together
in a two-byte variable through bitwise operations: the first
value is shifted left by one byte and the second value is stored in the
right byte through a bitwise OR. When reading the values back,
right shifts are performed to retrieve the previously stored
bytes. These shifts are executed in the wrong order, thus
reporting the values swapped as shown above.
This patch fixes this mistake by reversing the read
operations' order.
Signed-off-by: Giacomo Guiduzzi <guiduzzi.giacomo@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220322200653.15862-1-guiduzzi.giacomo@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f306cca42fe879694fb5e2382748c43dc9e0196 upstream.
For the RODE NT-USB the lowest Playback mixer volume setting mutes the
audio output. But it is not reported as such causing e.g. PulseAudio to
accidentally mute the device when selecting a low volume.
Fix this by applying the existing quirk for this kind of issue when the
device is detected.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220311201400.235892-1-lars@metafoo.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f68915b2efd0d6bfd6e124aa63c94b3c69f127c upstream.
snd_pcm_reset() is a non-atomic operation, and it's allowed to run
during the PCM stream running. It implies that the manipulation of
hw_ptr and other parameters might be racy.
This patch adds the PCM stream lock at appropriate places in
snd_pcm_*_reset() actions for covering that.
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20220322171325.4355-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 764f4eb6846f5475f1244767d24d25dd86528a4a upstream.
Whenever llc_ui_bind() and/or llc_ui_autobind()
took a reference on a netdevice but subsequently fail,
they must properly release their reference
or risk the infamous message from unregister_netdevice()
at device dismantle.
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: 赵子轩 <beraphin@gmail.com>
Reported-by: Stoyan Manolov <smanolov@suse.de>
Link: https://lore.kernel.org/r/20220323004147.1990845-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6821b0d9b56386d2bf14806f90ec401468c799f upstream.
In rare cases the display is flipped or mirrored. This was observed more
often in a low temperature environment. A clean reset on init_display()
should help to get registers in a sane state.
Fixes: ef8f317795da (staging: fbtft: use init function instead of init sequence)
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Link: https://lore.kernel.org/r/20220210085322.15676-1-oliver.graute@kococonnector.com
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e8e4c8f6673247e22efc7985ce5497accd16f88 upstream.
When an invalid (non existing) handle is used in a TPM command,
that uses the resource manager interface (/dev/tpmrm0) the resource
manager tries to load it from its internal cache, but fails and
the tpm_dev_transmit returns an -EINVAL error to the caller.
The existing async handler doesn't handle these error cases
currently and the condition in the poll handler never returns
mask with EPOLLIN set.
The result is that the poll call blocks and the application gets stuck
until the user_read_timer wakes it up after 120 sec.
Change the tpm_dev_async_work function to handle error conditions
returned from tpm_dev_transmit they are also reflected in the poll mask
and a correct error code could passed back to the caller.
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: <linux-integrity@vger.kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Fixes: 9e1b74a63f77 ("tpm: add support for nonblocking operation")
Tested-by: Jarkko Sakkinen<jarkko@kernel.org>
Signed-off-by: Tadeusz Struk <tstruk@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Tadeusz Struk <tadeusz.struk@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebe48d368e97d007bfeb76fcb065d6cfc4c96645 upstream.
The maximum message size that can be send is bigger than
the maximum site that skb_page_frag_refill can allocate.
So it is possible to write beyond the allocated buffer.
Fix this by doing a fallback to COW in that case.
v2:
Avoid get get_order() costs as suggested by Linus Torvalds.
Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a27 ("esp6: Avoid skb_cow_data whenever possible")
Reported-by: valis <sec@valis.email>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Vaibhav Rustagi <vaibhavrustagi@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fbcc1a4cb20fe26ad0225679c536c80f1648221 upstream.
It appears that there are some buffer overflows in EVT_TRANSACTION.
This happens because the length parameters that are passed to memcpy
come directly from skb->data and are not guarded in any way.
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Denis Efremov <denis.e.efremov@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9542e6a643fc69d528dfb3303f145719c61d3050 upstream.
Ensure that if the filecache laundrette gets stuck, it only affects
the knfsd instances of one container.
The notifier callbacks can be called from various contexts so avoid
using synchonous filesystem operations that might deadlock.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Cc: Khazhy Kumykov <khazhy@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3cf6a32f3f2a45944dd5be5c6ac4deb46bcd3bee upstream.
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
*curr = {rb_node = {__rb_parent_color = 278218928,
rb_right = 0x0, rb_left = 0x0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 40, type = 2 '\002',
binding = 0 '\000', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1159739e "kprobe_optinsn_page\t[__builtin__kprobes]"}
*prev = {rb_node = {__rb_parent_color = 278219041,
rb_right = 0x109548b0, rb_left = 0x109547c0},
start = 0xc000000000062354,
end = 0xc000000000062354, namelen = 12, type = 2 '\002',
binding = 1 '\001', idle = 0 '\000', ignore = 0 '\000',
inlined = 0 '\000', arch_sym = 0 '\000', annotate2 = false,
name = 0x1095486e "optinsn_slot"}
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c196c910 ("perf symbols: Improve kallsyms symbol end addr calculation")
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5600f6986628dde8881734090588474f54a540a8 upstream.
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce12 ("Input: aiptek - fix crash on detecting device without endpoints")
Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9b667a82cdcfe21d590344447d65daed52b353b upstream.
The syzbot fuzzer reported a minor bug in the usbtmc driver:
usb 5-1: BOGUS control dir, pipe 80001e80 doesn't match bRequestType 0
WARNING: CPU: 0 PID: 3813 at drivers/usb/core/urb.c:412
usb_submit_urb+0x13a5/0x1970 drivers/usb/core/urb.c:410
Modules linked in:
CPU: 0 PID: 3813 Comm: syz-executor122 Not tainted
5.17.0-rc5-syzkaller-00306-g2293be58d6a1 #0
...
Call Trace:
<TASK>
usb_start_wait_urb+0x113/0x530 drivers/usb/core/message.c:58
usb_internal_control_msg drivers/usb/core/message.c:102 [inline]
usb_control_msg+0x2a5/0x4b0 drivers/usb/core/message.c:153
usbtmc_ioctl_request drivers/usb/class/usbtmc.c:1947 [inline]
The problem is that usbtmc_ioctl_request() uses usb_rcvctrlpipe() for
all of its transfers, whether they are in or out. It's easy to fix.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+a48e3d1a875240cab5de@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiEsYTPEE6lOCOA5@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16b1941eac2bd499f065a6739a40ce0011a3d740 upstream.
The syzbot fuzzer found a use-after-free bug:
BUG: KASAN: use-after-free in dev_uevent+0x712/0x780 drivers/base/core.c:2320
Read of size 8 at addr ffff88802b934098 by task udevd/3689
CPU: 2 PID: 3689 Comm: udevd Not tainted 5.17.0-rc4-syzkaller-00229-g4f12b742eb2b #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
dev_uevent+0x712/0x780 drivers/base/core.c:2320
uevent_show+0x1b8/0x380 drivers/base/core.c:2391
dev_attr_show+0x4b/0x90 drivers/base/core.c:2094
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
Fixes: 2ccea03a8f7e ("usb: gadget: introduce UDC Class")
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+348b571beb5eeb70a582@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YiQgukfFFbBnwJ/9@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65f3324f4b6fed78b8761c3b74615ecf0ffa81fa upstream.
If "BufOffset" is very large the "BufOffset + 8" operation can have an
integer overflow.
Cc: stable@kernel.org
Fixes: 38ea1eac7d88 ("usb: gadget: rndis: check size of RNDIS_MSG_SET command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220301080424.GA17208@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f34b43e07cb512b28543fdcb9f35d1fbfda9ebc ]
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
Fixes: bd09128d16fa ("arm64: Add percpu vectors for EL1")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20220316183833.1563139-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb0b430b4e3acc88c85e0ad2e25f2a25a5765262 ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c2d ("net: dsa: get port type at parse time")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ee06de7729d795773145692e246a06448b1eb7a ]
This kind of interface doesn't have a mac header. This patch fixes
bpf_redirect() to a PIM interface.
Fixes: 27b29f63058d ("bpf: add bpf_redirect() helper")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220315092008.31423-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc1b6ef7bfb3d1d4df868b1c3e0480cacda6cd81 ]
The Innolux G070Y2-L01 supports two modes of operation:
1) FRC=Low/NC ... MEDIA_BUS_FMT_RGB666_1X7X3_SPWG ... BPP=6
2) FRC=High ..... MEDIA_BUS_FMT_RGB888_1X7X4_SPWG ... BPP=8
Currently the panel description mixes both, BPP from 1) and bus
format from 2), which triggers a warning at panel-simple.c:615.
Pick the later, set bpp=8, fix the warning.
Fixes: a5d2ade627dca ("drm/panel: simple: Add support for Innolux G070Y2-L01")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Fritz <chf.fritz@googlemail.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220220040718.532866-1-marex@denx.de
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 886e44c9298a6b428ae046e2fa092ca52e822e6a ]
As the potential failure of the kvmalloc_array(),
it should be better to check and restore the 'data'
if fails in order to avoid the dereference of the
NULL pointer.
Fixes: 6ae746711263 ("hv_netvsc: Add per-cpu ethtool stats for netvsc")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220314020125.2365084-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f74b29a4f53627376cf5a5fb7b0b3fa748a0b2b ]
As the potential failure of the dma_map_single(),
it should be better to check it and return error
if fails.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 837d9e49402eaf030db55a49f96fc51d73b4b441 ]
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc162 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.")
Signed-off-by: Kurt Cancemi <kurt@x64architecture.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
