IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 279c12df8d2efb28def9d037f288cbfb97c30fe2 ]
Commit e39d5ef67804 ("powerpc/5xxx: extend mpc8xxx_gpio driver to support
mpc512x gpios") implemented support for IRQ_TYPE_LEVEL_LOW flow type in
mpc512x via falling edge type. Do same for mpc85xx which support was added
in commit 345e5c8a1cc3 ("powerpc: Add interrupt support to mpc8xxx_gpio").
Fixes probing of lm90 hwmon driver on mpc85xx based board which use level
interrupt. Without it kernel prints error and refuse lm90 to work:
[ 15.258370] genirq: Setting trigger mode 8 for irq 49 failed (mpc8xxx_irq_set_type+0x0/0xf8)
[ 15.267168] lm90 0-004c: cannot request IRQ 49
[ 15.272708] lm90: probe of 0-004c failed with error -22
Fixes: 345e5c8a1cc3 ("powerpc: Add interrupt support to mpc8xxx_gpio")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 518e26f11af2fe4f5bebf9a0351595d508c7077f ]
The regcache sync will set the cache_bypass = true, at that
time, when there is regmap write operation, it will bypass
the regmap cache, then the regcache sync will write back the
value from cache to register, which is not as our expectation.
Though regmap already use its internal lock to avoid such issue,
but this driver force disable the regmap internal lock in its
regmap config: disable_locking = true
To avoid this issue, use the driver's own lock to do the protect
in system PM.
Fixes: b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d07a692f9562f9c06e62cce369e9dd108173a0f ]
We should use of_node_get() when a new reference of device_node
is created. It is noted that the old reference stored in
'mm_gc->gc.of_node' should also be decreased.
This patch is based on the fact that there is a call site in function
'qe_add_gpiochips()' of src file 'drivers\soc\fsl\qe\gpio.c'. In this
function, of_mm_gpiochip_add_data() is contained in an iteration of
for_each_compatible_node() which will automatically increase and
decrease the refcount. So we need additional of_node_get() for the
reference escape in of_mm_gpiochip_add_data().
Fixes: a19e3da5bc5f ("of/gpio: Kill of_gpio_chip and add members directly to gpio_chip")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db8edaa09d7461ec08672a92a2eef63d5882bb79 ]
For the device use NO AI mode(not support auto address increment),
only use the single read/write when config the regmap.
We meet issue on PCA9557PW on i.MX8QXP/DXL evk board, this device
do not support AI mode, but when do the regmap sync, regmap will
sync 3 byte data to register 1, logically this means write first
data to register 1, write second data to register 2, write third data
to register 3. But this device do not support AI mode, finally, these
three data write only into register 1 one by one. the reault is the
value of register 1 alway equal to the latest data, here is the third
data, no operation happened on register 2 and register 3. This is
not what we expect.
Fixes: 49427232764d ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c81aba8fde2aee4f5778ebab3a1d51bd2ef48e4c ]
commit 979934da9e7a ("[PATCH] mips: update IRQ handling for vr41xx") added
a function irq_dispatch, and it'll increase irq_err_count when the get_irq
callback returns a negative value, but increase irq_err_count in get_irq
was not removed.
And also, modpost complains once gpio-vr41xx drivers become modules.
ERROR: modpost: "irq_err_count" [drivers/gpio/gpio-vr41xx.ko] undefined!
So it would be a good idea to remove repetitive increase irq_err_count in
get_irq callback.
Fixes: 27fdd325dace ("MIPS: Update VR41xx GPIO driver to use gpiolib")
Fixes: 979934da9e7a ("[PATCH] mips: update IRQ handling for vr41xx")
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: huhai <huhai@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9bf3ac466faa83d51a8fe9212131701e58fdef74 ]
For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.
Fixes: 659d8a62311f ("gpio: vf610: add imx7ulp support")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e75f88efac05bf4e107e4171d8db6d8c3937252d upstream.
Gpiolib interprets the elements of "gpio-reserved-ranges" as "start,size"
because it clears "size" bits starting from the "start" bit in the according
bitmap. So it has to use "greater" instead of "greater or equal" when performs
bounds check to make sure that GPIOs are in the available range.
Previous implementation skipped ranges that include the last GPIO in
the range.
I wrote the mail to the maintainers
(https://lore.kernel.org/linux-gpio/20220412115554.159435-1-andrei.lalaev@emlid.com/T/#u)
of the questioned DTSes (because I couldn't understand how the maintainers
interpreted this property), but I haven't received a response.
Since the questioned DTSes use "gpio-reserved-ranges = <0 4>"
(i.e., the beginning of the range), this patch doesn't affect these DTSes at all.
TBH this patch doesn't break any existing DTSes because none of them
reserve gpios at the end of range.
Fixes: 726cb3ba4969 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Andrei Lalaev <andrei.lalaev@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 213d266ebfb1621aab79cfe63388facc520a1381 ]
When compiling with -Wformat, clang emits the following warning:
gpiolib-acpi.c:393:4: warning: format specifies type 'unsigned char' but the argument has type 'int' [-Wformat]
pin);
^~~
So warning that '%hhX' is paired with an 'int' is all just completely
mindless and wrong. Sadly, I can see a different bogus warning reason
why people would want to use '%02hhX'.
Again, the *sane* thing from a human perspective is to use '%02X. But
if the compiler doesn't do any range analysis at all, it could decide
that "Oh, that print format could need up to 8 bytes of space in the
result". Using '%02hhX' would cut that down to two.
And since we use
char ev_name[5];
and currently use "_%c%02hhX" as the format string, even a compiler
that doesn't notice that "pin <= 255" test that guards this all will
go "OK, that's at most 4 bytes and the final NUL termination, so it's
fine".
While a compiler - like gcc - that only sees that the original source
of the 'pin' value is a 'unsigned short' array, and then doesn't take
the "pin <= 255" into account, will warn like this:
gpiolib-acpi.c: In function 'acpi_gpiochip_request_interrupt':
gpiolib-acpi.c:206:24: warning: '%02X' directive writing between 2 and 4 bytes into a region of size 3 [-Wformat-overflow=]
sprintf(ev_name, "_%c%02X",
^~~~
gpiolib-acpi.c:206:20: note: directive argument in the range [0, 65535]
because gcc isn't being very good at that argument range analysis either.
In other words, the original use of 'hhx' was bogus to begin with, and
due to *another* compiler warning being bad, and we had that bad code
being written back in 2016 to work around _that_ compiler warning
(commit e40a3ae1f794: "gpio: acpi: work around false-positive
-Wstring-overflow warning").
Sadly, two different bad compiler warnings together does not make for
one good one.
It just makes for even more pain.
End result: I think the simplest and cleanest option is simply the
proposed change which undoes that '%hhX' change for gcc, and replaces
it with just using a slightly bigger stack allocation. It's not like
a 5-byte allocation is in any way likely to have saved any actual stack,
since all the other variables in that function are 'int' or bigger.
False-positive compiler warnings really do make people write worse
code, and that's a problem. But on a scale of bad code, I feel that
extending the buffer trivially is better than adding a pointless cast
that literally makes no sense.
At least in this case the end result isn't unreadable or buggy. We've
had several cases of bad compiler warnings that caused changes that
were actually horrendously wrong.
Fixes: e40a3ae1f794 ("gpio: acpi: work around false-positive -Wstring-overflow warning")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fe003547975680fdb9ff5ab0e41cb68276c4f2 ]
This works around an issue with the hardware where both OE and
DAT are exposed in the same register. If both are updated
simultaneously, the harware makes no guarantees that OE or DAT
will actually change in any given order and may result in a
glitch of a few ns on a GPIO pin when changing direction and value
in a single write.
Setting direction to input now only affects OE bit. Setting
direction to output updates DAT first, then OE.
Fixes: 9c6686322d74 ("gpio: add Technologic I2C-FPGA gpio support")
Signed-off-by: Mark Featherston <mark@embeddedTS.com>
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d1e972ace42390de739cde87d96043dcbe502286 upstream.
The tegra186 GPIO driver makes the assumption that the pointer
returned by irq_data_get_irq_chip_data() is a pointer to a
tegra_gpio structure. Unfortunately, it is actually a pointer
to the inner gpio_chip structure, as mandated by the gpiolib
infrastructure. Nice try.
The saving grace is that the gpio_chip is the first member of
tegra_gpio, so the bug has gone undetected since... forever.
Fix it by performing a container_of() on the pointer. This results
in no additional code, and makes it possible to understand how
the whole thing works.
Fixes: 5b2b135a87fc ("gpio: Add Tegra186 support")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20220211093904.1112679-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61a7904b6ace99b1bde0d0e867fa3097f5c8cee2 ]
The gpio-aspeed driver implements an irq_chip which need to be invoked
from hardirq context. Since spin_lock() can sleep with PREEMPT_RT, it is
no longer legal to invoke it while interrupts are disabled.
This also causes lockdep to complain about:
[ 0.649797] [ BUG: Invalid wait context ]
because aspeed_gpio.lock (spin_lock_t) is taken under irq_desc.lock
(raw_spinlock_t).
Let's use of raw_spinlock_t instead of spinlock_t.
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdfd6ab8fdccd8b138837efff66f4a1911496378 ]
If the IRQ is already in use, then acpi_dev_gpio_irq_get_by() really
should not change the type underneath the current owner.
I specifically hit an issue with this an a Chuwi Hi8 Super (CWI509) Bay
Trail tablet, when the Boot OS selection in the BIOS is set to Android.
In this case _STA for a MAX17047 ACPI I2C device wrongly returns 0xf and
the _CRS resources for this device include a GpioInt pointing to a GPIO
already in use by an _AEI handler, with a different type then specified
in the _CRS for the MAX17047 device. Leading to the acpi_dev_gpio_irq_get()
call done by the i2c-core-acpi.c code changing the type breaking the
_AEI handler.
Now this clearly is a bug in the DSDT of this tablet (in Android mode),
but in general calling irq_set_irq_type() on an IRQ which already is
in use seems like a bad idea.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 55a9968c7e139209a9e93d4ca4321731bea5fc95 upstream.
The commit 15add06841a3 ("gpio: pca953x: add ->set_config implementation")
introduced support for bias setting. However this, due to being half-baked,
brought potential issues:
- the turning bias via disabling makes the pin floating for a while;
- once enabled, bias can't be disabled.
Fix all these by adding support for bias disabling and move the disabling
part under the corresponding conditional.
While at it, add support for default setting, since it's cheap to add.
Fixes: 15add06841a3 ("gpio: pca953x: add ->set_config implementation")
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9b87f43537acfa24b95c236beba0f45901356eb2 ]
The tqmx86 MFD driver was passing IRQ 0 for "no IRQ" in the past. This
causes warnings with newer kernels.
Prepare the gpio-tqmx86 driver for the fixed MFD driver by handling a
missing IRQ properly.
Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d49b3a0f351925b5ea5047166c112b7590b918a ]
The On Semi pca9655 is a 16 bit variant of the On Semi pca9654 GPIO
expander, with 16 GPIOs and interrupt functionality.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
[Bartosz: fixed indentation as noted by Andy]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a51b2fb94b04ab71e53a71b9fad03fa826941254 ]
Return value of "pm_runtime_get_sync" API was neither captured nor checked.
Fixed it by capturing the return value and then checking for any warning.
Addresses-Coverity: "check_return"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6414e1a2bd26b0071e2b9d6034621f705dfd4c0 ]
Both of these drivers use ioport_map(), so they need to
depend on HAS_IOPORT_MAP. Otherwise, they cannot be built
even with COMPILE_TEST on architectures without an ioport
implementation, such as ARCH=um.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e948b1752b58c9c570989ab29ceef5b38fdccda ]
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da91ece226729c76f60708efc275ebd4716ad089 ]
Like some other Bay and Cherry Trail SoC based devices the Dell Venue
10 Pro 5055 has an embedded-controller which uses ACPI GPIO events to
report events instead of using the standard ACPI EC interface for this.
The EC interrupt is only used to report battery-level changes and
it keeps doing this while the system is suspended, causing the system
to not stay suspended.
Add an ignore-wake quirk for the GPIO pin used by the EC to fix the
spurious wakeups from suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ddd8d94ca31e768c76cf8bfe34ba7b10136b3694 ]
As we are using cpu_pm to save and restore context, we must also save and
restore the GPIO sysconfig register. This is needed because we are not
calling PM runtime functions at all with cpu_pm.
We need to save the sysconfig on idle as it's value can get reconfigured by
PM runtime and can be different from the init time value. Device specific
flags like "ti,no-idle-on-init" can affect the init value.
Fixes: b764a5863fd8 ("gpio: omap: Remove custom PM calls and use cpu_pm instead")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Adam Ford <aford173@gmail.com>
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23cf00ddd2e1aacf1873e43f5e0c519c120daf7a ]
Do not allow exporting GPIOs which are set invalid
by the driver's valid mask.
Fixes: 726cb3ba4969 ("gpiolib: Support 'gpio-reserved-ranges' property")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e5d5791730b55a1f987e1db84b078b91eb49e99 ]
fixed the following coccicheck:
./drivers/gpio/gpiolib-acpi.c:176:7-27: ERROR: Threaded IRQ with no
primary handler requested without IRQF_ONESHOT
Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a8002a35935aaefcd6a42ad3289f62bab947f2ca upstream.
If no n_latch value will be provided at driver probe then all pins will
be used as an input:
gpio->out = ~n_latch;
In that case initial state for all pins is "one":
gpio->status = gpio->out;
So if pcf857x IRQ happens with change pin value from "zero" to "one"
then we miss it, because of "one" from IRQ and "one" from initial state
leaves corresponding pin unchanged:
change = (gpio->status ^ status) & gpio->irq_enabled;
The right solution will be to read actual state at driver probe.
Cc: stable@vger.kernel.org
Fixes: 6e20a0a429bd ("gpio: pcf857x: enable gpio_to_irq() support")
Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 28dc10eb77a2db7681b08e3b109764bbe469e347 upstream.
Fixes the following warnings which results in interrupts disabled on
port B/F:
gpio gpiochip1: (B): detected irqchip that is shared with multiple gpiochips: please fix the driver.
gpio gpiochip5: (F): detected irqchip that is shared with multiple gpiochips: please fix the driver.
- added separate irqchip for each interrupt capable gpiochip
- provided unique names for each irqchip
Fixes: d2b091961510 ("gpio: ep93xx: Pass irqchip when adding gpiochip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b81a7ab8055d01d827ef66374b126eeac3bd108 upstream.
Two index spaces and ep93xx_gpio_port are confusing.
Instead add a separate struct to store necessary data and remove
ep93xx_gpio_port.
- add struct to store IRQ related data for each IRQ capable chip
- replace offset array with defined offsets
- add IRQ registers offset for each IRQ capable chip into
ep93xx_gpio_banks
------------[ cut here ]------------
kernel BUG at drivers/gpio/gpio-ep93xx.c:64!
---[ end trace 3f6544e133e9f5ae ]---
Fixes: fd935fc421e74 ("gpio: ep93xx: Do not pingpong irq numbers")
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e73b0101ae5124bf7cd3fb5d250302ad2f16a416 upstream.
The period is the sum of on and off values. That is, calculate period as
($on + $off) / clkrate
instead of
$off / clkrate - $on / clkrate
that makes no sense.
Reported-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 757642f9a584e ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[baruch: backport to kernels <= v5.10]
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 263ade7166a2e589c5b605272690c155c0637dcb ]
EIC controller have unfixed numbers of banks on different Spreadtrum SoCs,
and each bank has its own base address, the loop of getting there base
address in driver should break if the resource gotten via
platform_get_resource() is NULL already. The later ones would be all NULL
even if the loop continues.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201209055106.840100-1-zhang.lyra@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ed7d7dd4890bb8120a3e77c16191a695fdfcc5a ]
This reverts commit 0f5cb8cc27a266c81e6523b436479802e9aafc9e.
This commit will cause below warnings, since our EIC controller can support
differnt banks on different Spreadtrum SoCs, and each bank has its own base
address, we will get invalid resource warning if the bank number is less than
SPRD_EIC_MAX_BANK on some Spreadtrum SoCs.
So we should not use devm_platform_ioremap_resource() here to remove the
warnings.
[ 1.118508] sprd-eic 40210000.gpio: invalid resource
[ 1.118535] sprd-eic 40210000.gpio: invalid resource
[ 1.119034] sprd-eic 40210080.gpio: invalid resource
[ 1.119055] sprd-eic 40210080.gpio: invalid resource
[ 1.119462] sprd-eic 402100a0.gpio: invalid resource
[ 1.119482] sprd-eic 402100a0.gpio: invalid resource
[ 1.119893] sprd-eic 402100c0.gpio: invalid resource
[ 1.119913] sprd-eic 402100c0.gpio: invalid resource
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/8d3579f4b49bb675dc805035960f24852898be28.1585734060.git.baolin.wang7@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f57b295f990c0fa07f96d51ca1c82c52dbf79cc ]
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to putting operation will result in a
reference leak here.
A new function pm_runtime_resume_and_get is introduced in
[0] to keep usage counter balanced. So We fix the reference
leak by replacing it with new funtion.
[0] dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Fixes: c2df3de0d07e ("gpio: zynq: properly support runtime PM for GPIO used as interrupts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 10a2f11d3c9e48363c729419e0f0530dea76e4fe upstream.
This enables the PEX8311 internal PCI wire interrupt and the PEX8311
local interrupt input so the local interrupts are forwarded to the PCI.
Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23a7fdc06ebcc334fa667f0550676b035510b70b upstream.
This fixes the COS Enable Register value for enabling/disabling the
corresponding IRQs bank.
Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8f270efeac850c569c305dc0baa42ac3d607988 upstream.
Fix the bitwise operation to remove only the corresponding bit from the
mask.
Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e640b1eec38e4c8eba160f26cba4f592e657f3d ]
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c3e ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf0d394e885015941ed2d5724c0a6ed8d42dd95e ]
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac67b07e268d46eba675a60c37051bb3e59fd201 ]
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fcface659aab7eac4bd65dd116d98b8f7bb88d5 ]
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb47 ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")
Signed-off-by: Taiping Lai <taiping.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 214b0e1ad01abf4c1f6d8d28fa096bf167e47cef upstream.
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
Fixes: d88b25be3584 ("gpio: Add TC35892 GPIO driver")
Cc: Cc: stable@vger.kernel.org
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b02d9e770cd7087f34c743f85ccf5ea8372b047 upstream.
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397d1 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45ccf6556720293323c20cda717756014ff63007 upstream.
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de
Fixes: be8c8facc707 ("gpio: new driver to work with a 8x12 siox")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6f8cd246411575703d9312888b70705c396b53a9 ]
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200522080839.32612-1-dinghao.liu@zju.edu.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861254d826499944cb4d9b5a15f5a794a6b99a69 ]
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200605030052.78235-1-navid.emamdoost@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ec3decd21380081e3b5de4ba8d85d90a95f201a0 upstream.
It's a repetition of the commit aa58a21ae378
("gpio: pca953x: disable regmap locking")
which states the following:
This driver uses its own locking but regmap silently uses
a mutex for all operations too. Add the option to disable
locking to the regmap config struct.
Fixes: bcf41dc480b1 ("gpio: pca953x: fix handling of automatic address incrementing")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d8913504ccfeea6120df5ae1c6f4479ff09b931 ]
When adding a quirk for IRQ on Intel Galileo Gen 2 the commit ba8c90c61847
("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
missed GPIO resource release. We can safely do this in the same quirk, since
IRQ will be locked by GPIO framework when requested and unlocked on freeing.
Fixes: ba8c90c61847 ("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba8c90c6184784b397807b72403656085ac2f8c1 ]
ACPI table on Intel Galileo Gen 2 has wrong pin number for IRQ resource
of one of the I²C GPIO expanders. Since we know what that number is and
luckily have GPIO bases fixed for SoC's controllers, we may use a simple
DMI quirk to match the platform and retrieve GpioInt() pin on it for
the expander in question.
Mika suggested the way to avoid a quirk in the GPIO ACPI library and
here is the second, almost rewritten version of it.
Fixes: f32517bf1ae0 ("gpio: pca953x: support ACPI devices found on Galileo Gen2")
Depends-on: 25e3ef894eef ("gpio: acpi: Split out acpi_gpio_get_irq_resource() helper")
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcf41dc480b179bfb669a232080a2e26dc7294b4 ]
Some of the chips supported by the pca953x driver need the most
significant bit in the address word set to automatically increment the
address pointer on subsequent reads and writes (example: PCA9505). With
this bit unset the same register is read multiple times on a multi-byte
read sequence. Other chips must not have this bit set and autoincrement
always (example: PCA9555).
Up to now this AI bit was interpreted to be part of the address, which
resulted in inconsistent regmap caching when a register was written with
AI set and then read without it. This happened for the PCA9505 in
pca953x_gpio_set_multiple() where pca953x_read_regs() bulk read from the
cache for registers 0x8-0xc and then wrote to registers 0x88-0x8c. (Side
note: reading 5 values from offset 0x8 yiels OP0 5 times because AI must
be set to get OP0-OP4, which is another bug that is resolved here as a
by-product.) The same problem happens when calls to gpio_set_value() and
gpio_set_array_value() were mixed.
With this patch the AI bit is always set for chips that support it. This
works as there are no code locations that make use of the behaviour with
AI unset (for the chips that support it).
Note that the call to pca953x_setup_gpio() had to be done a bit earlier
to make the NBANK macro work.
The history of this bug is a bit complicated. Commit b32cecb46bdc
("gpio: pca953x: Extract the register address mangling to single
function") changed which chips and functions are affected. Commit
3b00691cc46a ("gpio: pca953x: hack to fix 24 bit gpio expanders") used
some duct tape to make the driver at least appear to work. Commit
49427232764d ("gpio: pca953x: Perform basic regmap conversion")
introduced the caching. Commit b4818afeacbd ("gpio: pca953x: Add
set_multiple to allow multiple bits to be set in one write.") introduced
the .set_multiple() callback which didn't work for chips that need the
AI bit which was fixed later for some chips in 8958262af3fb ("gpio:
pca953x: Repair multi-byte IO address increment on PCA9575"). So I'm
sorry, I don't know which commit I should pick for a Fixes: line.
Tested-by: Marcel Gudert <m.gudert@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
