IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 565fe150624ee77dc63a735cc1b3bff5101f38a3 ]
Currently the offset into the device when looking for OTP
bits can go outside of the address of the MTD NOR devices,
and if that memory isn't readable, bad things happen
on the IXP4xx (added prints that illustrate the problem before
the crash):
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x00000100
ixp4xx_copy_from copy from 0x00000100 to 0xc880dd78
cfi_intelext_otp_walk walk OTP on chip 0 start at reg_prot_offset 0x12000000
ixp4xx_copy_from copy from 0x12000000 to 0xc880dd78
8<--- cut here ---
Unable to handle kernel paging request at virtual address db000000
[db000000] *pgd=00000000
(...)
This happens in this case because the IXP4xx is big endian and
the 32- and 16-bit fields in the struct cfi_intelext_otpinfo are not
properly byteswapped. Compare to how the code in read_pri_intelext()
byteswaps the fields in struct cfi_pri_intelext.
Adding a small byte swapping loop for the OTP in read_pri_intelext()
and the crash goes away.
The problem went unnoticed for many years until I enabled
CONFIG_MTD_OTP on the IXP4xx as well, triggering the bug.
Cc: stable@vger.kernel.org
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20231020-mtd-otp-byteswap-v4-1-0d132c06aa9d@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b359ed5184aebf9d987e54abc5dae7ac03ed29ae ]
The flash controller implemented by the Arm Base platform behaves like
the Intel StrataFlash J3 device, but omits several features. In
particular it doesn't implement a protection register, so "Number of
Protection register fields" in the Primary Vendor-Specific Extended
Query, is 0.
The Intel StrataFlash J3 datasheet only lists 1 as a valid value for
NumProtectionFields. It describes the field as:
"Number of Protection register fields in JEDEC ID space.
“00h,” indicates that 256 protection bytes are available"
While a value of 0 may arguably not be architecturally valid, the
driver's current behavior is certainly wrong: if NumProtectionFields is
0, read_pri_intelext() adds a negative value to the unsigned extra_size,
and ends up in an infinite loop.
Fix it by ignoring a NumProtectionFields of 0.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Stable-dep-of: 565fe150624e ("mtd: cfi_cmdset_0001: Byte swap OTP info")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e01d5254698ea3d18e09d96b974c762328352cd ]
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: stable@vger.kernel.org
Fixes: 02f26ecf8c77 ("mtd: nand: add reworked Marvell NAND controller driver")
Reported-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ravi Chandra Minnikanti <rminnikanti@marvell.com>
Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-1-miquel.raynal@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6792b7fce610bcd1cf3e07af3607fe7e2c38c1d8 upstream.
When the exact mapping type driver was not available, the old
physmap_of_core driver fell back to mapping the region as ROM.
Unfortunately this feature was lost when the DT and pdata cases were
merged. Revive this useful feature.
Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/550e8c8c1da4c4baeb3d71ff79b14a18d4194f9e.1693407371.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5279f4a9eed3ee7d222b76511ea7a22c89e7eefd upstream.
We currently provide the physical address of the DMA region
rather than the output of dma_map_resource() which is obviously wrong.
Fixes: 7330fc505af4 ("mtd: rawnand: qcom: stop using phys_to_dma()")
Cc: stable@vger.kernel.org
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bibek Kumar Patro <quic_bibekkum@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230913070702.12707-1-quic_bibekkum@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 017c73a34a661a861712f7cc1393a123e5b2208c ]
There exists mtd devices with zero erasesize, which will trigger a
divide-by-zero exception while attaching ubi device.
Fix it by refusing attaching if mtd's erasesize is 0.
Fixes: 801c135ce73d ("UBI: Unsorted Block Images")
Reported-by: Yu Hao <yhao016@ucr.edu>
Link: https://lore.kernel.org/lkml/977347543.226888.1682011999468.JavaMail.zimbra@nod.at/T/
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ec2839a9062db8a592525a3fdabd42dcd9a3a9b upstream.
v7.2 controller has different ECC level field size and shift in the acc
control register than its predecessor and successor controller. It needs
to be set specifically.
Fixes: decba6d47869 ("mtd: brcmnand: Add v7.2 controller support")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-2-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cc0a598b944816f2968baf2631757f22721b996 upstream.
If system is busy during the command status polling function, the driver
may not get the chance to poll the status register till the end of time
out and return the premature status. Do a final check after time out
happens to ensure reading the correct status.
Fixes: 9d2ee0a60b8b ("mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-3-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d53244186c9ac58cb88d76a0958ca55b83a15cd upstream.
When the oob buffer length is not in multiple of words, the oob write
function does out-of-bounds read on the oob source buffer at the last
iteration. Fix that by always checking length limit on the oob buffer
read and fill with 0xff when reaching the end of the buffer to the oob
registers.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230706182909.79151-5-william.zhang@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a5a88125d00612586e941ae13e7fcf36ba8f18a7 ]
In fsmc_nand_resume(), the return value of clk_prepare_enable() should be
checked since it might fail.
Fixes: e25da1c07dfb ("mtd: fsmc_nand: Add clk_{un}prepare() support")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230817115839.10192-1-yiyang13@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e6b04f9238eab0f684fafd158c1f32ea65b9eaa upstream.
It is incorrect to calculate number of OOB bytes for ECC engine using
some "already known" ECC step size (1024 bytes here). Number of such
bytes for ECC engine must be whole OOB except 2 bytes for bad block
marker, while proper ECC step size and strength will be selected by
ECC logic.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230705065211.293500-1-AVKrasnov@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f649ab728cda8038259d8f14492fe400fbab911 upstream.
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c4d28e30a8d0b979e4029465ab8f312ab6ce2644 ]
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a6f4d346f3bad9c68b4a87701eb3f7978542d57 ]
When new timing values are calculated in marvell_nfc_setup_interface()
ensure that they will be applied in marvell_nfc_select_target() by
clearing the selected_chip pointer.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 650a8884a364ff2568b51cde9009cfd43cdae6ad ]
A few functions provide an empty interface definition when
CONFIG_MTD_NAND_INGENIC_ECC is disabled, but they are accidentally
defined as global functions in the header:
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:39:5: error: no previous prototype for 'ingenic_ecc_calculate'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:46:5: error: no previous prototype for 'ingenic_ecc_correct'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:53:6: error: no previous prototype for 'ingenic_ecc_release'
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h:57:21: error: no previous prototype for 'of_ingenic_ecc_get'
Turn them into 'static inline' definitions instead.
Fixes: 15de8c6efd0e ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230516202133.559488-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2087e85bb66ee3652dafe732bb9b9b896229eafc ]
The cadence QSPI driver misbehaves after performing a full system suspend
resume:
...
spi-nor spi0.0: resume() failed
...
This results in a flash connected via OSPI interface after system suspend-
resume to be unusable.
fix these suspend and resume functions.
Fixes: 140623410536 ("mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller")
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230417091027.966146-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 935da5e5100f57d843cac4781b21f1c235059aa0 ]
dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider
is not yet probed. Currently driver just falls back to using PIO mode
(which is less efficient) in this case. Instead return probe deferral
error as is so that driver will be re probed once DMA provider is
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-6-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 2087e85bb66e ("spi: cadence-quadspi: fix suspend-resume implementations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a99705079a91e6373122bd0ca2fc129b688fc5b3 ]
Currently direct access mode is used on platforms that have AHB window
(memory mapped window) larger than flash size. This feature is limited
to TI platforms as non TI platforms have < 1MB of AHB window.
Therefore introduce a driver quirk to disable DAC mode and set it for
non TI compatibles. This is in preparation to move to spi-mem framework
where flash geometry cannot be known.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 2087e85bb66e ("spi: cadence-quadspi: fix suspend-resume implementations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 834b4e8d344139ba64cda22099b2b2ef6c9a542d ]
Drop configuration of Flash size, erase size and page size
configuration. Flash size is needed only if using AHB decoder (BIT 23 of
CONFIG_REG) which is not used by the driver.
Erase size and page size are needed if IP is configured to send WREN
automatically. But since SPI NOR layer takes care of sending WREN, there
is no need to configure these fields either.
Therefore drop these in preparation to move the driver to spi-mem
framework where flash geometry is not visible to controller driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 2087e85bb66e ("spi: cadence-quadspi: fix suspend-resume implementations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 31a149d5c13c4cbcf97de3435817263a2d8c9d6e upstream.
The commit 2d78aee426d8 ("UBI: simplify LEB write and atomic LEB change code")
adds helper function, try_write_vid_and_data(), to simplify the code, but this
helper function has bug, it will return 0 (success) when ubi_io_write_vid_hdr()
or the ubi_io_write_data() return error number (-EIO, etc), because the return
value of ubi_wl_put_peb() will overwrite the original return value.
This issue will cause unexpected data loss issue, because the caller of this
function and UBIFS willn't know the data is lost.
Fixes: 2d78aee426d8 ("UBI: simplify LEB write and atomic LEB change code")
Cc: stable@vger.kernel.org
Signed-off-by: Wang YanQing <udknight@gmail.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f773f0a331d6c41733b17bebbc1b6cae12e016f5 ]
During the processing of the bgt, if the sync_erase() return -EBUSY
or some other error code in __erase_worker(),schedule_erase() called
again lead to the down_read(ubi->work_sem) hold twice and may get
block by down_write(ubi->work_sem) in ubi_update_fastmap(),
which cause deadlock.
ubi bgt other task
do_work
down_read(&ubi->work_sem) ubi_update_fastmap
erase_worker # Blocked by down_read
__erase_worker down_write(&ubi->work_sem)
schedule_erase
schedule_ubi_work
down_read(&ubi->work_sem)
Fix this by changing input parameter @nested of the schedule_erase() to
'true' to avoid recursively acquiring the down_read(&ubi->work_sem).
Also, fix the incorrect comment about @nested parameter of the
schedule_erase() because when down_write(ubi->work_sem) is held, the
@nested is also need be true.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217093
Fixes: 2e8f08deabbc ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab4e4de9fd8b469823a645f05f2c142e9270b012 ]
Fixes the following W=1 kernel build warning(s):
drivers/mtd/ubi/wl.c:584: warning: Function parameter or member 'nested' not described in 'schedule_erase'
drivers/mtd/ubi/wl.c:1075: warning: Excess function parameter 'shutdown' description in '__erase_worker'
Cc: Richard Weinberger <richard@nod.at>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-13-lee.jones@linaro.org
Stable-dep-of: f773f0a331d6 ("ubi: Fix deadlock caused by recursively holding work_sem")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e020e1b96afdecd20680b5b5be2a6ffc3d27628 upstream.
Following process will make ubi attaching failed since commit
1b42b1a36fc946 ("ubi: ensure that VID header offset ... size"):
ID="0xec,0xa1,0x00,0x15" # 128M 128KB 2KB
modprobe nandsim id_bytes=$ID
flash_eraseall /dev/mtd0
modprobe ubi mtd="0,2048" # set vid_hdr offset as 2048 (one page)
(dmesg):
ubi0 error: ubi_attach_mtd_dev [ubi]: VID header offset 2048 too large.
UBI error: cannot attach mtd0
UBI error: cannot initialize UBI, error -22
Rework original solution, the key point is making sure
'vid_hdr_shift + UBI_VID_HDR_SIZE < ubi->vid_hdr_alsize',
so we should check vid_hdr_shift rather not vid_hdr_offset.
Then, ubi still support (sub)page aligined VID header offset.
Fixes: 1b42b1a36fc946 ("ubi: ensure that VID header offset ... size")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> # v5.10, v4.19
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93942b70461574ca7fc3d91494ca89b16a4c64c7 upstream.
Valid mask is 0x3FFF, without this patch the following problems were
found:
1) [ 0.938914] Could not find a valid ONFI parameter page, trying
bit-wise majority to recover it
[ 0.947384] ONFI parameter recovery failed, aborting
2) Read with disabled ECC mode was broken.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/3794ffbf-dfea-e96f-1f97-fe235b005e19@sberdevices.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0c3089601f064d80b3838eceb711fcac04bceaad upstream.
mtd_read() may return -EUCLEAN in case of corrected bit-flips.This
particular condition should not be treated like an error.
Signed-off-by: Bang Li <libang.linuxer@gmail.com>
Fixes: e47f68587b82 ("mtd: check for max_bitflips in mtd_read_oob()")
Cc: <stable@vger.kernel.org> # v3.7
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230328163012.4264-1-libang.linuxer@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e732e39ed9929c05fd219035bc9653ba4100d4fa ]
'info_buf' memory is cached and driver polls ECC bit in it. This bit
is set by the NAND controller. If 'usleep_range()' returns before device
sets this bit, 'info_buf' will be cached and driver won't see update of
this bit and will loop forever.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/d4ef0bd6-816e-f6fa-9385-f05f775f0ae2@sberdevices.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a240bc5c43130c6aa50831d7caaa02a1d84e1bce ]
Wear-leveling entry could be freed in error path, which may be accessed
again in eraseblk_count_seq_show(), for example:
__erase_worker eraseblk_count_seq_show
wl = ubi->lookuptbl[*block_number]
if (wl)
wl_entry_destroy
ubi->lookuptbl[e->pnum] = NULL
kmem_cache_free(ubi_wl_entry_slab, e)
erase_count = wl->ec // UAF!
Wear-leveling entry updating/accessing in ubi->lookuptbl should be
protected by ubi->wl_lock, fix it by adding ubi->wl_lock to serialize
wl entry accessing between wl_entry_destroy() and
eraseblk_count_seq_show().
Fetch a reproducer in [Link].
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216305
Fixes: 7bccd12d27b7e3 ("ubi: Add debugfs file for tracking PEB state")
Fixes: 801c135ce73d5d ("UBI: Unsorted Block Images")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c15859bfd326c10230f09cb48a17f8a35f190342 ]
It willl cause null-ptr-deref in the following case:
uif_init()
ubi_add_volume()
cdev_add() -> if it fails, call kill_volumes()
device_register()
kill_volumes() -> if ubi_add_volume() fails call this function
ubi_free_volume()
cdev_del()
device_unregister() -> trying to delete a not added device,
it causes null-ptr-deref
So in ubi_free_volume(), it delete devices whether they are added
or not, it will causes null-ptr-deref.
Handle the error case whlie calling ubi_add_volume() to fix this
problem. If add volume fails, set the corresponding vol to null,
so it can not be accessed in kill_volumes() and release the
resource in ubi_add_volume() error path.
Fixes: 801c135ce73d ("UBI: Unsorted Block Images")
Suggested-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9af31d6ec1a4be4caab2550096c6bd2ba8fba472 ]
There is an use-after-free problem reported by KASAN:
==================================================================
BUG: KASAN: use-after-free in ubi_eba_copy_table+0x11f/0x1c0 [ubi]
Read of size 8 at addr ffff888101eec008 by task ubirsvol/4735
CPU: 2 PID: 4735 Comm: ubirsvol
Not tainted 6.1.0-rc1-00003-g84fa3304a7fc-dirty #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_report+0x171/0x472
kasan_report+0xad/0x130
ubi_eba_copy_table+0x11f/0x1c0 [ubi]
ubi_resize_volume+0x4f9/0xbc0 [ubi]
ubi_cdev_ioctl+0x701/0x1850 [ubi]
__x64_sys_ioctl+0x11d/0x170
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
When ubi_change_vtbl_record() returns an error in ubi_resize_volume(),
"new_eba_tbl" will be freed on error handing path, but it is holded
by "vol->eba_tbl" in ubi_eba_replace_table(). It means that the liftcycle
of "vol->eba_tbl" and "vol" are different, so when resizing volume in
next time, it causing an use-after-free fault.
Fix it by not freeing "new_eba_tbl" after it replaced in
ubi_eba_replace_table(), while will be freed in next volume resizing.
Fixes: 801c135ce73d ("UBI: Unsorted Block Images")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2ebc336be08160debfe27f87660cf550d710f3e9 upstream.
Erase can be zeroed in spi_nor_parse_4bait() or
spi_nor_init_non_uniform_erase_map(). In practice it happened with
mt25qu256a, which supports 4K, 32K, 64K erases with 3b address commands,
but only 4K and 64K erase with 4b address commands.
Fixes: dc92843159a7 ("mtd: spi-nor: fix erase_type array to indicate current map conf")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211119081412.29732-1-alexander.sverdlin@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6a43cd02ddbc597dc9a1f82c1e433f871a2f6f06 ]
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221012152135.28353-1-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0fddf9ad06fd9f439f137139861556671673e31c upstream.
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce107713b722af57c4b7f2477594d445b496420e upstream.
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org
Fixes: 7a08dbaedd36 ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e4ad3212cf22687410b1e8f4e68feec50646113 ]
The meson_nfc_ecc_correct() function accidentally does a right shift
instead of a left shift so it only works for BIT(0). Also use
BIT_ULL() because "correct_bitmap" is a u64 and we want to avoid
shift wrapping bugs.
Fixes: 8fae856c5350 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YuI2zF1hP65+LE7r@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26e784433e6c65735cd6d93a8db52531970d9a60 ]
The function devm_ioremap() in docg3_probe() can fail, so
its return value should be checked.
Fixes: 82402aeb8c81e ("mtd: docg3: Use devm_*() functions")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220722091644.2937953-1-williamsukatube@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
