IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 6ccf50d4d4741e064ba35511a95402c63bbe21a8 ]
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23d775f12dcd23d052a4927195f15e970e27ab26 ]
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e70c ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ae90f90e4909e3014e2dc6a0627964617a7b824 ]
All MT7530 switch IP variants share the MT7530_MFC register, but the
current driver only writes it for the switch variant that is integrated in
the MT7621 SoC. Modify the code to include all MT7530 derivatives.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a59a58ec25d44f853c26bdbfda47d73b3067435 ]
LAN9303 doesn't associate FDB (ALR) entries with VLANs, it has just one
global Address Logic Resolution table [1].
Ignore VID in port_fdb_{add|del} methods, go on with the global table. This
is the same semantics as hellcreek or RZ/N1 implement.
Visible symptoms:
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to delete 00:xx:xx:xx:xx:cf vid 1 from fdb: -2
LAN9303_MDIO 5b050000.ethernet-1:00: port 2 failed to add 00:xx:xx:xx:xx:cf vid 1 to fdb: -95
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/00002308A.pdf
Fixes: 0620427ea0d6 ("net: dsa: lan9303: Add fdb/mdb manipulation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230531143826.477267-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c27f3d53d588618d81d30d6712459a3cc9489b8 ]
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c218d8021e36e226add4bab93d071d30fe0704 ]
The multi-chip module MT7530 switch with a 40 MHz oscillator on the
MT7621AT, MT7621DAT, and MT7621ST SoCs forwards corrupt frames using
trgmii.
This is caused by the assumption that MT7621 SoCs have got 150 MHz PLL,
hence using the ncpo1 value, 0x0780.
My testing shows this value works on Unielec U7621-06, Bartel's testing
shows it won't work on Hi-Link HLK-MT7621A and Netgear WAC104. All devices
tested have got 40 MHz oscillators.
Using the value for 125 MHz PLL, 0x0640, works on all boards at hand. The
definitions for 125 MHz PLL exist on the Banana Pi BPI-R2 BSP source code
whilst 150 MHz PLL don't.
Forwarding frames using trgmii on the MCM MT7530 switch with a 25 MHz
oscillator on the said MT7621 SoCs works fine because the ncpo1 value
defined for it is for 125 MHz PLL.
Change the 150 MHz PLL comment to 125 MHz PLL, and use the 125 MHz PLL
ncpo1 values for both oscillator frequencies.
Link: 81d24bbce7/u-boot-mt/drivers/net/rt2880_eth.c (L2195)
Fixes: 7ef6f6f8d237 ("net: dsa: mt7530: Add MT7621 TRGMII mode support")
Tested-by: Bartel Eerdekens <bartel.eerdekens@constell8.be>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45977e58ce65ed0459edc9a0466d9dfea09463f5 ]
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bcad0f0e6fbc1d613e49e0ee35c8e5f2e685bb0 ]
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257c6 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c977c5c2e4c5d8ad1b604724cc344e38f96fe9b ]
ALU table entry 2 register in KSZ9477 have bit positions reserved for
forwarding port map. This field is referred in ksz9477_fdb_del() for
clearing forward port map and alu table.
But current fdb_del refer ALU table entry 3 register for accessing forward
port map. Update ksz9477_fdb_del() to get forward port map from correct
alu table entry register.
With this bug, issue can be observed while deleting static MAC entries.
Delete any specific MAC entry using "bridge fdb del" command. This should
clear all the specified MAC entries. But it is observed that entries with
self static alone are retained.
Tested on LAN9370 EVB since ksz9477_fdb_del() is used common across
LAN937x and KSZ series.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230118174735.702377-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8964916d206071b058c6351f88b1966bd58cbde0 ]
This patch fixes an issue where a read failure of a port statistic counter
will return unknown results. While it is highly unlikely the read will
ever fail, it is much cleaner to return a zero for the stat count.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221209153502.7429-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 1fae6eb0fc91d3ecb539e03f9e4dcd1c53ada553.
Upstream commit was a fix for an overlook of setting "ent.is_valid"
twice after 5d65b64a3d97 ("net: dsa: b53: Add support for MDB").
Since MDB support was not backported to stable kernels (it's not a bug
fix) there is nothing to fix there. Backporting this commit resulted in
"env.is_valid" not being set at all.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39f59bca275d2d819a8788c0f962e9e89843efc9 ]
This patch changes the reported ethtool statistics for the lan9303
family of parts covered by this driver.
The TxUnderRun statistic label is renamed to RxShort to accurately
reflect what stat the device is reporting. I did not reorder the
statistics as that might cause problems with existing user code that
are expecting the stats at a certain offset.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221128193559.6572-1-jerry.ray@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 633efc8b3dc96f56f5a57f2a49764853a2fa3f50 ]
kmemleak reported memory leaks in dsa_loop_init():
kmemleak: 12 new suspected memory leaks
unreferenced object 0xffff8880138ce000 (size 2048):
comm "modprobe", pid 390, jiffies 4295040478 (age 238.976s)
backtrace:
[<000000006a94f1d5>] kmalloc_trace+0x26/0x60
[<00000000a9c44622>] phy_device_create+0x5d/0x970
[<00000000d0ee2afc>] get_phy_device+0xf3/0x2b0
[<00000000dca0c71f>] __fixed_phy_register.part.0+0x92/0x4e0
[<000000008a834798>] fixed_phy_register+0x84/0xb0
[<0000000055223fcb>] dsa_loop_init+0xa9/0x116 [dsa_loop]
...
There are two reasons for memleak in dsa_loop_init().
First, fixed_phy_register() create and register phy_device:
fixed_phy_register()
get_phy_device()
phy_device_create() # freed by phy_device_free()
phy_device_register() # freed by phy_device_remove()
But fixed_phy_unregister() only calls phy_device_remove().
So the memory allocated in phy_device_create() is leaked.
Second, when mdio_driver_register() fail in dsa_loop_init(),
it just returns and there is no cleanup for phydevs.
Fix the problems by catching the error of mdio_driver_register()
in dsa_loop_init(), then calling both fixed_phy_unregister() and
phy_device_free() to release phydevs.
Also add a function for phydevs cleanup to avoid duplacate.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 36c0d935015766bf20d621c18313f17691bda5e3 upstream.
In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 246bbf2f977ea36aaf41f5d24370fef433250728 upstream.
If the port isn't a CPU port nor a user port, 'cpu_dp'
is a null pointer and a crash happened on dereferencing
it in mv88e6060_setup_port():
[ 9.575872] Unable to handle kernel NULL pointer dereference at virtual address 00000014
...
[ 9.942216] mv88e6060_setup from dsa_register_switch+0x814/0xe84
[ 9.948616] dsa_register_switch from mdio_probe+0x2c/0x54
[ 9.954433] mdio_probe from really_probe.part.0+0x98/0x2a0
[ 9.960375] really_probe.part.0 from driver_probe_device+0x30/0x10c
[ 9.967029] driver_probe_device from __device_attach_driver+0xb8/0x13c
[ 9.973946] __device_attach_driver from bus_for_each_drv+0x90/0xe0
[ 9.980509] bus_for_each_drv from __device_attach+0x110/0x184
[ 9.986632] __device_attach from bus_probe_device+0x8c/0x94
[ 9.992577] bus_probe_device from deferred_probe_work_func+0x78/0xa8
[ 9.999311] deferred_probe_work_func from process_one_work+0x290/0x73c
[ 10.006292] process_one_work from worker_thread+0x30/0x4b8
[ 10.012155] worker_thread from kthread+0xd4/0x10c
[ 10.017238] kthread from ret_from_fork+0x14/0x3c
Fixes: 0abfd494deef ("net: dsa: use dedicated CPU port")
CC: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220811070939.1717146-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c97bc0128b2eecc703106112679a69d446d1a12 upstream.
The pause settings reported by the PHY should also be applied to the GMII port
status override otherwise the switch will not generate pause frames towards the
link partner despite the advertisement saying otherwise.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220623030204.1966851-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0737e018a05e2aa352828c52bdeed3b02cff2930 ]
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
when breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the gphy_fw_np.
Add missing of_node_put() to avoid refcount leak.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605072335.11257-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02ded5a173619b11728b8bf75a3fd995a2c1ff28 ]
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71cffebf6358a7f5031f5b208bbdc1cb4db6e539 ]
Commit 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining
GSWIP_MII_CFG bits") added all known bits in the GSWIP_MII_CFGp
register. It helped bring this register into a well-defined state so the
driver has to rely less on the bootloader to do things right.
Unfortunately it also sets the GSWIP_MII_CFG_RMII_CLK bit without any
possibility to configure it. Upon further testing it turns out that all
boards which are supported by the GSWIP driver in OpenWrt which use an
RMII PHY have a dedicated oscillator on the board which provides the
50MHz RMII reference clock.
Don't set the GSWIP_MII_CFG_RMII_CLK bit (but keep the code which always
clears it) to fix support for the Fritz!Box 7362 SL in OpenWrt. This is
a board with two Atheros AR8030 RMII PHYs. With the "RMII clock" bit set
the MAC also generates the RMII reference clock whose signal then
conflicts with the signal from the oscillator on the board. This results
in a constant cycle of the PHY detecting link up/down (and as a result
of that: the two ports using the AR8030 PHYs are not working).
At the time of writing this patch there's no known board where the MAC
(GSWIP) has to generate the RMII reference clock. If needed this can be
implemented in future by providing a device-tree flag so the
GSWIP_MII_CFG_RMII_CLK bit can be toggled per port.
Fixes: 4b5923249b8fa4 ("net: dsa: lantiq_gswip: Configure all remaining GSWIP_MII_CFG bits")
Tested-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20220425152027.2220750-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6da69b1da130e7d96766042750cd9f902e890eba ]
The bug is here:
return rule;
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff783c7 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 585d42bb57bb358d48906660a8de273b078810b1 ]
This chip has support for the same per-port policy actions found in
later versions of LinkStreet devices.
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e981bc74aefc6a177b50c16cfa7023599799cf74 ]
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6bb9681a43f34f2cab4aad6e2a02da4ce54d13c5 upstream.
The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this. Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted. Other uses of the gpio already use the correct polarity.
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f5f12f5d4b108399130bb5c11f07765851d9cdb ]
The max VLAN number with non-4K VLAN activated is 15, and the
range is 0..15. Not 16.
The impact should be low since we by default have 4K VLAN and
thus have 4095 VLANs to play with in this switch. There will
not be a problem unless the code is rewritten to only use
16 VLANs.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66d262804a2276721eac86cf18fcd61046149193 ]
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cdb067d31c0fe4cce98b9d15f1f2ef525acaa094 ]
It isn't true that CPU port is always the last one. Switches BCM5301x
have 9 ports (port 6 being inactive) and they use port 5 as CPU by
default (depending on design some other may be CPU ports too).
A more reliable way of determining number of ports is to check for the
last set bit in the "enabled_ports" bitfield.
This fixes b53 internal state, it will allow providing accurate info to
the DSA and is required to fix BCM5301x support.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 552799f8b3b0074d2617f53a63a088f9514a66e3 upstream.
Currently, outgoing packets larger than 1496 bytes are dropped when
tagged VLAN is used on a switch port.
Add the frame check sequence length to the value of the register
GSWIP_MAC_FLEN to fix this. This matches the lantiq_ppa vendor driver,
which uses a value consisting of 1518 bytes for the MAC frame, plus the
lengths of special tag and VLAN tags.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7428022b50d0fbb4846dd0f00639ea09d36dff02 upstream.
When a port leaves a VLAN-aware bridge, the current code does not clear
other ports' matrix field bit. If the bridge is later set to VLAN-unaware
mode, traffic in the bridge may leak to that port.
Remove the VLAN filtering check in mt7530_port_bridge_leave.
Fixes: 474a2ddaa192 ("net: dsa: mt7530: fix VLAN traffic leaks")
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21b52fed928e96d2f75d2f6aa9eac7a4b0b55d22 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 871a73a1c8f55da0a3db234e9dd816ea4fd546f2 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: 58c59ef9e930 ("net: dsa: lantiq: Add Forwarding Database access")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ada2fee185d8145afb89056558bb59545b9dbdd0 ]
rtnl_fdb_dump() has logic to split a dump of PF_BRIDGE neighbors into
multiple netlink skbs if the buffer provided by user space is too small
(one buffer will typically handle a few hundred FDB entries).
When the current buffer becomes full, nlmsg_put() in
dsa_slave_port_fdb_do_dump() returns -EMSGSIZE and DSA saves the index
of the last dumped FDB entry, returns to rtnl_fdb_dump() up to that
point, and then the dump resumes on the same port with a new skb, and
FDB entries up to the saved index are simply skipped.
Since dsa_slave_port_fdb_do_dump() is pointed to by the "cb" passed to
drivers, then drivers must check for the -EMSGSIZE error code returned
by it. Otherwise, when a netlink skb becomes full, DSA will no longer
save newly dumped FDB entries to it, but the driver will continue
dumping. So FDB entries will be missing from the dump.
Fix the broken backpressure by propagating the "cb" return code and
allow rtnl_fdb_dump() to restart the FDB dump with a new skb.
Fixes: ab335349b852 ("net: dsa: lan9303: Add port_fast_age and port_fdb_dump methods")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c34f674c8875235725c3ef86147a627f165d23b4 ]
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08a2 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aff51c5da3208bd164381e1488998667269c6cf4 ]
Add the missing RxUnicast counter.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c5fc159e0927531707895709eee1f8bfa04289f ]
The procedure to add a static FDB entry in sja1105 is concurrent with
dynamic learning performed on all bridge ports and the CPU port.
The switch looks up the FDB from left to right, and also learns
dynamically from left to right, so it is possible that between the
moment when we pick up a free slot to install an FDB entry, another slot
to the left of that one becomes free due to an address ageing out, and
that other slot is then immediately used by the switch to learn
dynamically the same address as we're trying to add statically.
The result is that we succeeded to add our static FDB entry, but it is
being shadowed by a dynamic FDB entry to its left, and the switch will
behave as if our static FDB entry did not exist.
We cannot really prevent this from happening unless we make the entire
process to add a static FDB entry a huge critical section where address
learning is temporarily disabled on _all_ ports, and then re-enabled
according to the configuration done by sja1105_port_set_learning.
However, that is kind of disruptive for the operation of the network.
What we can do alternatively is to simply read back the FDB for dynamic
entries located before our newly added static one, and delete them.
This will guarantee that our static FDB entry is now operational. It
will still not guarantee that there aren't dynamic FDB entries to the
_right_ of that static FDB entry, but at least those entries will age
out by themselves since they aren't hit, and won't bother anyone.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e11e865bf84e3c6ea91563ff3e858cfe0e184bd2 ]
The SJA1105 switch family leaves it up to software to decide where
within the FDB to install a static entry, and to concatenate destination
ports for already existing entries (the FDB is also used for multicast
entries), it is not as simple as just saying "please add this entry".
This means we first need to search for an existing FDB entry before
adding a new one. The driver currently manages to fool itself into
thinking that if an FDB entry already exists, there is nothing to be
done. But that FDB entry might be dynamically learned, case in which it
should be replaced with a static entry, but instead it is left alone.
This patch checks the LOCKEDS ("locked/static") bit from found FDB
entries, and lets the code "goto skip_finding_an_index;" if the FDB
entry was not static. So we also need to move the place where we set
LOCKEDS = true, to cover the new case where a dynamic FDB entry existed
but was dynamic.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Fixes: 1da73821343c ("net: dsa: sja1105: Add FDB operations for P/Q/R/S series")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3709488790022c85720f991bff50d48ed5a36e6a upstream.
Commit 9e5baf9b36367 ("net: dsa: mv88e6xxx: add RMU disable op")
introduced .rmu_disable() method with implementation for several models,
but forgot to add Topaz, which can use the Peridot implementation.
Use the Peridot implementation of .rmu_disable() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 9e5baf9b36367 ("net: dsa: mv88e6xxx: add RMU disable op")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7da467d82d1ed4fb317aff836f99709169e73f10 upstream.
Commit f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
introduced .port_set_policy() method with implementation for several
models, but forgot to add Topaz, which can use the 6352 implementation.
Use the 6352 implementation of .port_set_policy() on Topaz.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a2cd326e44 ("net: dsa: mv88e6xxx: introduce .port_set_policy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8c42a49738f16af0061f9ae5c2f5a955f268d9e3 ]
Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6729188d2646709941903052e4b78e1d82c239b9 upstream.
The driver continues probing when a port is configured for an
unsupported PHY interface type, instead it should stop.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 474a2ddaa192777522a7499784f1d60691cd831a upstream.
PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but
was not reset when it is disabled, which may cause traffic leaks:
ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 type bridge vlan_filtering 0
ip link set br1 type bridge vlan_filtering 0
# traffic in br0 and br1 will start leaking to each other
As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the
PCR_MATRIX write from mt7530_port_set_vlan_aware.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1fe976d308acb6374c899a4ee8025a0a016e453e upstream.
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5923249b8fa427943b50b8f35265176472be38 upstream.
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Updated after the upstream commit 3e9005be87777 required some changes
for Linux 5.4 ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e9005be87777afc902b9f5497495898202d335d upstream.
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Move gswip_port_set_{speed, duplex, pause} calls from
gswip_phylink_mac_link_up to gswip_phylink_mac_config because the
data required for these functions is not available inside
gswip_phylink_mac_link_up yet in Linux 5.4 (it was only added with
Linux 5.7). ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e6fdeb28f4c331acbd27bdb0effc4befd4ef8e8 upstream.
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream.
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68f7 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47142ed6c34d544ae9f0463e58d482289cbe0d46 ]
Similar to commit 92696286f3bb37ba50e4bd8d1beb24afb759a799 ("net:
bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to
qualify the phydev->dev_flags based on whether the port is connected to
an internal or external PHY otherwise we risk having a flags collision
with a completely different interpretation depending on the driver.
Fixes: aa9aef77c761 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9b3827ee66cfcf297d0acd6ecf33653a5f297ef upstream.
Add support for being able to set the learning attribute on port, and
make sure that the standalone ports start up with learning disabled.
We can remove the code in bcm_sf2 that configured the ports learning
attribute because we want the standalone ports to have learning disabled
by default and port 7 cannot be bridged, so its learning attribute will
not change past its initial configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
