IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 19d5b2698c35b2132a355c67b4d429053804f8cc upstream.
Explicitly set the 'family' driver_info struct member for leafimx.
Previously, the correct operation relied on KVASER_LEAF being the first
defined value in enum kvaser_usb_leaf_family.
Fixes: e6c80e601053 ("can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20240628194529.312968-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6841cab8c4504835e4011689cbdb3351dec693fd ]
This race condition was discovered while updating the at91_can driver
to use can_bus_off(). The following scenario describes how the
converted at91_can driver would behave.
When a CAN device goes into BUS-OFF state, the driver usually
stops/resets the CAN device and calls can_bus_off().
This function sets the netif carrier to off, and (if configured by
user space) schedules a delayed work that calls can_restart() to
restart the CAN device.
The can_restart() function first checks if the carrier is off and
triggers an error message if the carrier is OK.
Then it calls the driver's do_set_mode() function to restart the
device, then it sets the netif carrier to on. There is a race window
between these two calls.
The at91 CAN controller (observed on the sama5d3, a single core 32 bit
ARM CPU) has a hardware limitation. If the device goes into bus-off
while sending a CAN frame, there is no way to abort the sending of
this frame. After the controller is enabled again, another attempt is
made to send it.
If the bus is still faulty, the device immediately goes back to the
bus-off state. The driver calls can_bus_off(), the netif carrier is
switched off and another can_restart is scheduled. This occurs within
the race window before the original can_restart() handler marks the
netif carrier as OK. This would cause the 2nd can_restart() to be
called with an OK netif carrier, resulting in an error message.
The flow of the 1st can_restart() looks like this:
can_restart()
// bail out if netif_carrier is OK
netif_carrier_ok(dev)
priv->do_set_mode(dev, CAN_MODE_START)
// enable CAN controller
// sama5d3 restarts sending old message
// CAN devices goes into BUS_OFF, triggers IRQ
// IRQ handler start
at91_irq()
at91_irq_err_line()
can_bus_off()
netif_carrier_off()
schedule_delayed_work()
// IRQ handler end
netif_carrier_on()
The 2nd can_restart() will be called with an OK netif carrier and the
error message will be printed.
To close the race window, first set the netif carrier to on, then
restart the controller. In case the restart fails with an error code,
roll back the netif carrier to off.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-2-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe5c9940dfd8ba0c73672dddb30acd1b7a11d4c7 ]
During testing, I triggered a can_restart() with the netif carrier
being OK [1]. The BUG_ON, which checks if the carrier is OK, results
in a fatal kernel crash. This is neither helpful for debugging nor for
a production system.
[1] The root cause is a race condition in can_restart() which will be
fixed in the next patch.
Do not crash the kernel, issue an error message instead, and continue
restarting the CAN device anyway.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20231005-can-dev-fix-can-restart-v2-1-91b5c1fd922c@pengutronix.de
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c8bc15f02b85bc8f47074110d8fd8caf7a1e42d ]
In case of an RX overflow error from the CAN controller and an OOM
where no skb can be allocated, the error counters are not incremented.
Fix this by first incrementing the error counters and then allocate
the skb.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20230718-gs_usb-cleanups-v1-7-c3b9154ec605@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f534f6581ec084fe94d6759f7672bd009794b07e ]
veth and vxcan need to make sure the ifindexes of the peer
are not negative, core does not validate this.
Using iproute2 with user-space-level checking removed:
Before:
# ./ip link add index 10 type veth peer index -1
# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:74:b2:03 brd ff:ff:ff:ff:ff:ff
10: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 8a:90:ff:57:6d:5d brd ff:ff:ff:ff:ff:ff
-1: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:ed:18:e6:fa:7f brd ff:ff:ff:ff:ff:ff
Now:
$ ./ip link add index 10 type veth peer index -1
Error: ifindex can't be negative.
This problem surfaced in net-next because an explicit WARN()
was added, the root cause is older.
Fixes: e6f8f1a739b6 ("veth: Allow to create peer link with given ifindex")
Fixes: a8f820a380a2 ("can: add Virtual CAN Tunnel driver (vxcan)")
Reported-by: syzbot+5ba06978f34abb058571@syzkaller.appspotmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f8a2da6ec2417cca169fa85a8ab15817bccbb109 upstream.
After an initial link up the CAN device is in ERROR-ACTIVE mode. Due
to a missing CAN_STATE_STOPPED in gs_can_close() it doesn't change to
STOPPED after a link down:
| ip link set dev can0 up
| ip link set dev can0 down
| ip --details link show can0
| 13: can0: <NOARP,ECHO> mtu 16 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can state ERROR-ACTIVE restart-ms 1000
Add missing assignment of CAN_STATE_STOPPED in gs_can_close().
Cc: stable@vger.kernel.org
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20230718-gs_usb-fix-can-state-v1-1-f19738ae2c23@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f649ab728cda8038259d8f14492fe400fbab911 upstream.
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 262d7a52ba27525e3c1203230c9f0524e48bbb34 upstream.
Under certain circumstances we send two EFLUSH commands, resulting in two
EFLUSH ack packets, while only expecting a single EFLUSH ack.
This can cause the driver Tx flush completion to get out of sync.
To avoid this problem, don't enable the "Transmit buffer flush done" (TFD)
interrupt and remove the code handling it.
Now we only send EFLUSH command after receiving status packet with
"Init detected" (IDET) bit set.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf7ac55e991ca177f1ac16be51152f1ef291a4df upstream.
The listen-only bit was never cleared, causing the controller to
always use listen-only mode, if previously set.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c589557dd1426f5adf90c7a919d4fde5a3e4ef64 upstream.
Empty the "Shared receive buffer" (SRB) in probe, to assure we start in a
known state, and don't process any irrelevant packets.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aed0e6ca7dbb8fbea9bc69c9ac663d5533c8c5d8 upstream.
Set can.state to CAN_STATE_STOPPED in kvaser_pciefd_stop().
Without this fix, wrong CAN state was repported after the interface was
brought down.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/r/20230516134318.104279-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 118469f88180438ef43dee93d71f77c00e7b425d ]
Move the supply for cf->data[3] (bit stream position of CAN error), in
case of a bus- or protocol-error, outside of the "switch (ecc &
SJA1000_ECC_MASK){}"-statement, because this bit stream position is
independent of the error type.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20230216190450.3901254-2-frank.jungclaus@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f006229135b7debf4037adb1eb93e358559593db ]
Debian's gcc-13 [1] throws the following error in
kvaser_usb_hydra_cmd_size():
[1] gcc version 13.0.0 20221214 (experimental) [master r13-4693-g512098a3316] (Debian 13-20221214-1)
| drivers/net/can/usb/kvaser_usb/kvaser_usb_hydra.c:502:65: error:
| array subscript ‘struct kvaser_cmd_ext[0]’ is partly outside array
| bounds of ‘unsigned char[32]’ [-Werror=array-bounds=]
| 502 | ret = le16_to_cpu(((struct kvaser_cmd_ext *)cmd)->len);
kvaser_usb_hydra_cmd_size() returns the size of given command. It
depends on the command number (cmd->header.cmd_no). For extended
commands (cmd->header.cmd_no == CMD_EXTENDED) the above shown code is
executed.
Help gcc to recognize that this code path is not taken in all cases,
by calling kvaser_usb_hydra_cmd_size() directly after assigning the
command number.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Link: https://lore.kernel.org/all/20221219110104.1073881-1-mkl@pengutronix.de
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40c9e4f676abbe194541d88e796341c92d5a13c0 ]
Register 0x824 TCAN4X5X_MCAN_INT_REG is a read-only register. Any writes
to this register do not have any effect.
Remove this write. The m_can driver aldready clears the interrupts in
m_can_isr() by writing to M_CAN_IR which is translated to register
0x1050 which is a writable version of this register.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/all/20221206115728.1056014-9-msp@baylibre.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39d3df6b0ea80f9b515c632ca07b39b1c156edee ]
The device will respond with a CMD_ERROR_EVENT command, with error_code
KVASER_USB_{LEAF,HYDRA}_ERROR_EVENT_PARAM, if the CMD_SET_BUSPARAMS_REQ
contains invalid bittiming parameters.
However, this command does not contain any channel reference.
To check if the CMD_SET_BUSPARAMS_REQ was successful, redback and compare
the requested bittiming parameters with the device reported parameters.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-12-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90904d326269a38fe5dd895fb2db7c03199654c4 ]
When auto-restart is enabled, the kvaser_usb_leaf driver considers
transition from any state >= CAN_STATE_BUS_OFF as a bus-off recovery
event (restart).
However, these events may occur at interface startup time before
kvaser_usb_open() has set the state to CAN_STATE_ERROR_ACTIVE, causing
restarts counter to increase and CAN_ERR_RESTARTED to be sent despite no
actual restart having occurred.
Fix that by making the auto-restart condition checks more strict so that
they only trigger when the interface was actually in the BUS_OFF state.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11249acf802341294557895d8e5f6aef080253f ]
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 sends a
CMD_CHIP_STATE_EVENT indicating bus-off after stopping the device,
causing a stopped device to appear as CAN_STATE_BUS_OFF instead of
CAN_STATE_STOPPED.
Fix that by not handling error events on stopped devices.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d21f5927ae604881f98587fabf6753f88730968 ]
The tested 0bfd:0017 Kvaser Memorator Professional HS/HS FW 2.0.50 and
0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778 do not seem to send
any unsolicited events when error counters decrease or when the device
transitions from ERROR_PASSIVE to ERROR_ACTIVE (or WARNING).
This causes the interface to e.g. indefinitely stay in the ERROR_PASSIVE
state.
Fix that by asking for chip state (inc. counters) event every 0.5 secs
when error counters are non-zero.
Since there are non-error-counter devices, also always poll in
ERROR_PASSIVE even if the counters show zero.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df1b7af2761b935f63b4a53e789d41ed859edf61 ]
kvaser_usb_leaf_rx_error_update_can_state() sets error state according
to error counters when the hardware does not indicate a specific state
directly.
However, this is currently gated behind a check for
M16C_STATE_BUS_ERROR which does not always seem to be set when error
counters are increasing, and may not be set when error counters are
decreasing.
This causes the CAN_STATE_ERROR_WARNING state to not be set in some
cases even when appropriate.
Change the code to set error state from counters even without
M16C_STATE_BUS_ERROR.
The Error-Passive case seems superfluous as it is already set via
M16C_STATE_BUS_PASSIVE flag above, but it is kept for now.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b24cb2d169e0c9dce664a959e1f2aa9781285dc9 ]
The device will send an error event command, to indicate certain errors.
This indicates a misbehaving driver, and should never occur.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Co-developed-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35364f5b41a4917fe94a3f393d149b63ec583297 ]
Use the CMD_GET_CAPABILITIES_REQ command to query the device for certain
capabilities. We are only interested in LISTENONLY mode and wither the
device reports CAN error counters.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b0ce2c67795672115ac6ca28351a78799cd114b ]
The CAN error message frames (i.e. error skb) are an interface
specific to socket CAN. The payload of the CAN error message frames
does not correspond to any actual data sent on the wire. Only an error
flag and a delimiter are transmitted when an error occurs (c.f. ISO
11898-1 section 10.4.4.2 "Error flag").
For this reason, it makes no sense to increment the tx_packets and
tx_bytes fields of struct net_device_stats when sending an error
message frame because no actual payload will be transmitted on the
wire.
N.B. Sending error message frames is a very specific feature which, at
the moment, is only supported by the Kvaser Hydra hardware. Please
refer to [1] for more details on the topic.
[1] https://lore.kernel.org/linux-can/CAMZ6RqK0rTNg3u3mBpZOoY51jLZ-et-J01tY6-+mWsM4meVw-A@mail.gmail.com/t/#u
Link: https://lore.kernel.org/all/20211207121531.42941-3-mailhol.vincent@wanadoo.fr
Co-developed-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stable-dep-of: 35364f5b41a4 ("can: kvaser_usb: kvaser_usb_leaf: Get capabilities from device")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a8e3bd25f1e789c8154e11ea24dc3ec5a4c1da0 ]
Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've observed, both with my oscilloscope and captured USB packets
below, you must send "0" to turn it ON, and "1" to turn it OFF.
From the schematics in the user's guide, I can confirm that you must
drive the CAN_RES signal LOW "0" to activate the resistors.
Reverse the argument value of usb_msg.termination to fix this.
These are the two commands sequence, ON then OFF.
> No. Time Source Destination Protocol Length Info
> 1 0.000000 host 1.3.1 USB 46 URB_BULK out
>
> Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80000000000000000000000000000000000a8
>
> No. Time Source Destination Protocol Length Info
> 2 4.372547 host 1.3.1 USB 46 URB_BULK out
>
> Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80100000000000000000000000000000000a9
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Link: https://lore.kernel.org/all/20221124152504.125994-1-yashi@spacecubics.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 918ee4911f7a41fb4505dff877c1d7f9f64eb43e ]
We don't get any further EVENT from an esd CAN USB device for changes
on REC or TEC while those counters converge to 0 (with ecc == 0). So
when handling the "Back to Error Active"-event force txerr = rxerr =
0, otherwise the berr-counters might stay on values like 95 forever.
Also, to make life easier during the ongoing development a
netdev_dbg() has been introduced to allow dumping error events send by
an esd CAN USB device.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20221130202242.3998219-2-frank.jungclaus@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62ec89e74099a3d6995988ed9f2f996b368417ec ]
Add the missing free_cc770dev() before return from cc770_isa_probe()
in the register_cc770dev() error handling case.
In addition, remove blanks before goto labels.
Fixes: 7e02e5433e00 ("can: cc770: legacy CC770 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168557-6024-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92dfd9310a71d28cefe6a2d5174d43fab240e631 ]
Add the missing free_sja1000dev() before return from
sja1000_isa_probe() in the register_sja1000dev() error handling case.
In addition, remove blanks before goto labels.
Fixes: 2a6ba39ad6a2 ("can: sja1000: legacy SJA1000 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168521-5540-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 702de2c21eed04c67cefaaedc248ef16e5f6b293 upstream.
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com
Cc: stable@vger.kernel.org
[mkl: adjust commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[biju: removed gpriv from RCANFD_RFCC_RFIE macro]
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3e5b3418827cefb5e1cc658806f02965791b8f07 ]
The commit 1149108e2fbf ("can: mscan: improve clock API use") only
adds put_clock() in mpc5xxx_can_remove() function, forgetting to add
put_clock() in the error handling code.
Fix this bug by adding put_clock() in the error handling code.
Fixes: 1149108e2fbf ("can: mscan: improve clock API use")
Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/all/20221024133828.35881-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2871edb32f4622c3a25ce4b3977bad9050b91974 upstream.
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0be1a655fe68c8e6dcadbcbddb69cf2fb29881f5 upstream.
can_restart() expects CMD_START_CHIP to set the error state to
ERROR_ACTIVE as it calls netif_carrier_on() immediately afterwards.
Otherwise the user may immediately trigger restart again and hit a
BUG_ON() in can_restart().
Fix kvaser_usb_leaf set_mode(CMD_START_CHIP) to set the expected state.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 455561fb618fde40558776b5b8435f9420f335db upstream.
The TX queue seems to be implicitly flushed by the hardware during
bus-off or bus-off recovery, but the driver does not reset the TX
bookkeeping.
Despite not resetting TX bookkeeping the driver still re-enables TX
queue unconditionally, leading to "cannot find free context" /
NETDEV_TX_BUSY errors if the TX queue was full at bus-off time.
Fix that by resetting TX bookkeeping on CAN restart.
Tested with 0bfd:0124 Kvaser Mini PCI Express 2xHS FW 4.18.778.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1499ecaea9d2ba68d5e18d80573b4561a8dc4ee7 upstream.
For command events read from the device,
kvaser_usb_leaf_read_bulk_callback() verifies that cmd->len does not
exceed the size of the received data, but the actual kvaser_cmd handlers
will happily read any kvaser_cmd fields without checking for cmd->len.
This can cause an overread if the last cmd in the buffer is shorter than
expected for the command type (with cmd->len showing the actual short
size).
Maximum overread seems to be 22 bytes (CMD_LEAF_LOG_MESSAGE), some of
which are delivered to userspace as-is.
Fix that by verifying the length of command before handling it.
This issue can only occur after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd7f30e174d09a02ca2afa5ef093fb0f0352e0d8 upstream.
flush_comp is initialized when CMD_FLUSH_QUEUE is sent to the device and
completed when the device sends CMD_FLUSH_QUEUE_RESP.
This causes completion of uninitialized completion if the device sends
CMD_FLUSH_QUEUE_RESP before CMD_FLUSH_QUEUE is ever sent (e.g. as a
response to a flush by a previously bound driver, or a misbehaving
device).
Fix that by initializing flush_comp in kvaser_usb_init_one() like the
other completions.
This issue is only triggerable after RX URBs have been set up, i.e. the
interface has been opened at least once.
Cc: stable@vger.kernel.org
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Tested-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20221010150829.199676-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5440428b3da65408dba0241985acb7a05258b85e ]
The dev->can.state is set to CAN_STATE_ERROR_ACTIVE, after the device
has been started. On busy networks the CAN controller might receive
CAN frame between and go into an error state before the dev->can.state
is assigned.
Assign dev->can.state before starting the controller to close the race
window.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220920195216.232481-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d80d60b0db6ff3dd2e29247cc2a5166d7e9ae37e upstream.
The mcp251x driver uses both receiving mailboxes of the CAN controller
chips. For retrieving the CAN frames from the controller via SPI, it checks
once per interrupt which mailboxes have been filled and will retrieve the
messages accordingly.
This introduces a race condition, as another CAN frame can enter mailbox 1
while mailbox 0 is emptied. If now another CAN frame enters mailbox 0 until
the interrupt handler is called next, mailbox 0 is emptied before
mailbox 1, leading to out-of-order CAN frames in the network device.
This is fixed by checking the interrupt flags once again after freeing
mailbox 0, to correctly also empty mailbox 1 before leaving the handler.
For reproducing the bug I created the following setup:
- Two CAN devices, one Raspberry Pi with MCP2515, the other can be any.
- Setup CAN to 1 MHz
- Spam bursts of 5 CAN-messages with increasing CAN-ids
- Continue sending the bursts while sleeping a second between the bursts
- Check on the RPi whether the received messages have increasing CAN-ids
- Without this patch, every burst of messages will contain a flipped pair
v3: https://lore.kernel.org/all/20220804075914.67569-1-sebastian.wuerl@ororatech.com
v2: https://lore.kernel.org/all/20220804064803.63157-1-sebastian.wuerl@ororatech.com
v1: https://lore.kernel.org/all/20220803153300.58732-1-sebastian.wuerl@ororatech.com
Fixes: bf66f3736a94 ("can: mcp251x: Move to threaded interrupts instead of workqueues.")
Signed-off-by: Sebastian Würl <sebastian.wuerl@ororatech.com>
Link: https://lore.kernel.org/all/20220804081411.68567-1-sebastian.wuerl@ororatech.com
[mkl: reduce scope of intf1, eflag1]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a4cb6e62ea4d36e53fb3c0f18ea4503d7b76674f upstream.
clang emits a -Wunaligned-access warning on struct __packed
ems_cpc_msg.
The reason is that the anonymous union msg (not declared as packed) is
being packed right after some non naturally aligned variables (3*8
bits + 2*32) inside a packed struct:
| struct __packed ems_cpc_msg {
| u8 type; /* type of message */
| u8 length; /* length of data within union 'msg' */
| u8 msgid; /* confirmation handle */
| __le32 ts_sec; /* timestamp in seconds */
| __le32 ts_nsec; /* timestamp in nano seconds */
| /* ^ not naturally aligned */
|
| union {
| /* ^ not declared as packed */
| u8 generic[64];
| struct cpc_can_msg can_msg;
| struct cpc_can_params can_params;
| struct cpc_confirm confirmation;
| struct cpc_overrun overrun;
| struct cpc_can_error error;
| struct cpc_can_err_counter err_counter;
| u8 can_state;
| } msg;
| };
Starting from LLVM 14, having an unpacked struct nested in a packed
struct triggers a warning. c.f. [1].
Fix the warning by marking the anonymous union as packed.
[1] https://github.com/llvm/llvm-project/issues/55520
Fixes: 702171adeed3 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/all/20220802094021.959858-1-mkl@pengutronix.de
Cc: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9950f11211331180269867aef848c7cf56861742 ]
After commit 3a5c7e4611dd, the variable errc is accessed before being
initialized, c.f. below W=2 warning:
| In function 'pch_can_error',
| inlined from 'pch_can_poll' at drivers/net/can/pch_can.c:739:4:
| drivers/net/can/pch_can.c:501:29: warning: 'errc' may be used uninitialized [-Wmaybe-uninitialized]
| 501 | cf->data[6] = errc & PCH_TEC;
| | ^
| drivers/net/can/pch_can.c: In function 'pch_can_poll':
| drivers/net/can/pch_can.c:484:13: note: 'errc' was declared here
| 484 | u32 errc, lec;
| | ^~~~
Moving errc initialization up solves this issue.
Fixes: 3a5c7e4611dd ("can: pch_can: do not report txerr and rxerr during bus-off")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/all/20220721160032.9348-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebe8a2433cd090ccdc222861f44bddb75eb01de ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/all/20220719143550.3681-10-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a57732084e06791d37ea1ea447cca46220737abd ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 7259124eac7d1 ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c")
Link: https://lore.kernel.org/all/20220719143550.3681-9-mailhol.vincent@wanadoo.fr
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 936e90595376e64b6247c72d3ea8b8b164b7ac96 ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Link: https://lore.kernel.org/all/20220719143550.3681-8-mailhol.vincent@wanadoo.fr
CC: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ac15a8f661b941519379831d09bfb12271b23ee ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0738eff14d81 ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Link: https://lore.kernel.org/all/20220719143550.3681-7-mailhol.vincent@wanadoo.fr
CC: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a22bd630cfff496b270211745536e50e98eb3a45 ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 57e83fb9b746 ("can: hi311x: Add Holt HI-311x CAN driver")
Link: https://lore.kernel.org/all/20220719143550.3681-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 164d7cb2d5a30f1b3a5ab4fab1a27731fb1494a8 ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 215db1856e83 ("can: sja1000: Consolidate and unify state change handling")
Link: https://lore.kernel.org/all/20220719143550.3681-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a37b7245e831a641df360ca41db6a71c023d3746 ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Link: https://lore.kernel.org/all/20220719143550.3681-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a5c7e4611ddcf0ef37a3a17296b964d986161a6 ]
During bus off, the error count is greater than 255 and can not fit in
a u8.
Fixes: 0c78ab76a05c ("pch_can: Add setting TEC/REC statistics processing")
Link: https://lore.kernel.org/all/20220719143550.3681-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2e8e79c416aae1de224c0f1860f2e3350fa171f8 upstream.
can_put_echo_skb() will clone skb then free the skb. Move the
can_put_echo_skb() for the m_can version 3.0.x directly before the
start of the xmit in hardware, similar to the 3.1.x branch.
Fixes: 80646733f11c ("can: m_can: update to support CAN FD features")
Link: https://lore.kernel.org/all/20220317081305.739554-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Reported-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[sudip: adjust context]
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
