IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 30a92c9e3d6b073932762bef2ac66f4ee784c657 ]
Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames. With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions. If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception. This is gated by the
skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another. In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized. This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup. To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.
Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets. In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.
This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments. We need
larger environments for this because we need to ensure that flow
misses occur. In these environment, without this patch, we can see:
./ovn_cluster.sh start
podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)
--- 21.0.0.3 ping statistics ---
...
Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.
With this patch, setting the pkt_type, we see the following:
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
ping: local error: message too long, mtu=1222
--- 21.0.0.3 ping statistics ---
...
In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.
Tested-by: Jaime Caamano <jcaamano@redhat.com>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848a5a7 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240516200941.16152-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c988176b6c16c516474f6fceebe0f055af5eb56 ]
OVS_PACKET_CMD_EXECUTE has 3 main attributes:
- OVS_PACKET_ATTR_KEY - Packet metadata in a netlink format.
- OVS_PACKET_ATTR_PACKET - Binary packet content.
- OVS_PACKET_ATTR_ACTIONS - Actions to execute on the packet.
OVS_PACKET_ATTR_KEY is parsed first to populate sw_flow_key structure
with the metadata like conntrack state, input port, recirculation id,
etc. Then the packet itself gets parsed to populate the rest of the
keys from the packet headers.
Whenever the packet parsing code starts parsing the ICMPv6 header, it
first zeroes out fields in the key corresponding to Neighbor Discovery
information even if it is not an ND packet.
It is an 'ipv6.nd' field. However, the 'ipv6' is a union that shares
the space between 'nd' and 'ct_orig' that holds the original tuple
conntrack metadata parsed from the OVS_PACKET_ATTR_KEY.
ND packets should not normally have conntrack state, so it's fine to
share the space, but normal ICMPv6 Echo packets or maybe other types of
ICMPv6 can have the state attached and it should not be overwritten.
The issue results in all but the last 4 bytes of the destination
address being wiped from the original conntrack tuple leading to
incorrect packet matching and potentially executing wrong actions
in case this packet recirculates within the datapath or goes back
to userspace.
ND fields should not be accessed in non-ND packets, so not clearing
them should be fine. Executing memset() only for actual ND packets to
avoid the issue.
Initializing the whole thing before parsing is needed because ND packet
may not contain all the options.
The issue only affects the OVS_PACKET_CMD_EXECUTE path and doesn't
affect packets entering OVS datapath from network interfaces, because
in this case CT metadata is populated from skb after the packet is
already parsed.
Fixes: 9dd7f8907c37 ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Reported-by: Antonin Bas <antonin.bas@broadcom.com>
Closes: https://github.com/openvswitch/ovs-issues/issues/327
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240509094228.1035477-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ea7b72d4fac2fdbc0425cd8f2ea33abe95235b2 ]
Since kfree_rcu, which is called in the hlist_for_each_entry_rcu traversal
of ovs_ct_limit_exit, is not part of the RCU read critical section, it
is possible that the RCU grace period will pass during the traversal and
the key will be free.
To prevent this, it should be changed to hlist_for_each_entry_safe.
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/ZiYvzQN/Ry5oeFQW@v4bel-B760M-AORUS-ELITE-AX
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4539f91f2a801c0c028c252bffae56030cfb2cae ]
On startup, ovs-vswitchd probes different datapath features including
support for timeout policies. While probing, it tries to execute
certain operations with OVS_PACKET_ATTR_PROBE or OVS_FLOW_ATTR_PROBE
attributes set. These attributes tell the openvswitch module to not
log any errors when they occur as it is expected that some of the
probes will fail.
For some reason, setting the timeout policy ignores the PROBE attribute
and logs a failure anyway. This is causing the following kernel log
on each re-start of ovs-vswitchd:
kernel: Failed to associated timeout policy `ovs_test_tp'
Fix that by using the same logging macro that all other messages are
using. The message will still be printed at info level when needed
and will be rate limited, but with a net rate limiter instead of
generic printk one.
The nf_ct_set_timeout() itself will still print some info messages,
but at least this change makes logging in openvswitch module more
consistent.
Fixes: 06bd2bdf19d2 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240403203803.2137962-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68bb10101e6b0a6bb44e9c908ef795fc4af99eae ]
The commit mentioned below causes the ovs_flow_tbl_lookup() function
to be called with the masked key. However, it's supposed to be called
with the unmasked key. This due to the fact that the datapath supports
installing wider flows, and OVS relies on this behavior. For example
if ipv4(src=1.1.1.1/192.0.0.0, dst=1.1.1.2/192.0.0.0) exists, a wider
flow (smaller mask) of ipv4(src=192.1.1.1/128.0.0.0,dst=192.1.1.2/
128.0.0.0) is allowed to be added.
However, if we try to add a wildcard rule, the installation fails:
$ ovs-appctl dpctl/add-flow system@myDP "in_port(1),eth_type(0x0800), \
ipv4(src=1.1.1.1/192.0.0.0,dst=1.1.1.2/192.0.0.0,frag=no)" 2
$ ovs-appctl dpctl/add-flow system@myDP "in_port(1),eth_type(0x0800), \
ipv4(src=192.1.1.1/0.0.0.0,dst=49.1.1.2/0.0.0.0,frag=no)" 2
ovs-vswitchd: updating flow table (File exists)
The reason is that the key used to determine if the flow is already
present in the system uses the original key ANDed with the mask.
This results in the IP address not being part of the (miniflow) key,
i.e., being substituted with an all-zero value. When doing the actual
lookup, this results in the key wrongfully matching the first flow,
and therefore the flow does not get installed.
This change reverses the commit below, but rather than having the key
on the stack, it's allocated.
Fixes: 190aa3e77880 ("openvswitch: Fix Frame-size larger than 1024 bytes warning.")
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd954cc1919e35cb92f78671cab6e42d661945a3 ]
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com
Fixes: 44da5ae5fbea ("openvswitch: Drop user features if old user space attempted to create datapath")
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c21ab2afa2c64896a7f0e3cbc6845ec63dcfad2e ]
Currently queue_userspace_packet will call kfree_skb for all frames,
whether or not an error occurred. This can result in a single dropped
frame being reported as multiple drops in dropwatch. This functions
caller may also call kfree_skb in case of an error. This patch will
consume the skbs instead and allow caller's to use kfree_skb.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109957
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1100248a5c5ccd57059eb8d02ec077e839a23826 ]
Frames sent to userspace can be reported as dropped in
ovs_dp_process_packet, however, if they are dropped in the netlink code
then netlink_attachskb will report the same frame as dropped.
This patch checks for error codes which indicate that the frame has
already been freed.
Signed-off-by: Mike Pattrick <mkp@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2109946
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 12378a5a75e33f34f8586706eb61cca9e6d4690c upstream.
When a packet enters the OVS datapath and does not match any existing
flows installed in the kernel flow cache, the packet will be sent to
userspace to be parsed, and a new flow will be created. The kernel and
OVS rely on each other to parse packet fields in the same way so that
packets will be handled properly.
As per the design document linked below, OVS expects all later IPv6
fragments to have nw_proto=44 in the flow key, so they can be correctly
matched on OpenFlow rules. OpenFlow controllers create pipelines based
on this design.
This behavior was changed by the commit in the Fixes tag so that
nw_proto equals the next_header field of the last extension header.
However, there is no counterpart for this change in OVS userspace,
meaning that this field is parsed differently between OVS and the
kernel. This is a problem because OVS creates actions based on what is
parsed in userspace, but the kernel-provided flow key is used as a match
criteria, as described in Documentation/networking/openvswitch.rst. This
leads to issues such as packets incorrectly matching on a flow and thus
the wrong list of actions being applied to the packet. Such changes in
packet parsing cannot be implemented without breaking the userspace.
The offending commit is partially reverted to restore the expected
behavior.
The change technically made sense and there is a good reason that it was
implemented, but it does not comply with the original design of OVS.
If in the future someone wants to implement such a change, then it must
be user-configurable and disabled by default to preserve backwards
compatibility with existing OVS versions.
Cc: stable@vger.kernel.org
Fixes: fa642f08839b ("openvswitch: Derive IP protocol number for IPv6 later frags")
Link: https://docs.openvswitch.org/en/latest/topics/design/#fragments
Signed-off-by: Rosemarie O'Riorden <roriorden@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220621204845.9721-1-roriorden@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f30fb9166d4f15a1aa19449b9da871fe0ed4796 upstream.
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a4036 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport for 5.4: Removed handling of OVS_ACTION_ATTR_DEC_TTL as it
doesn't exist in this version. BUILD_BUG_ON condition adjusted
accordingly.]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2061ecfdf2350994e5b61c43e50e98a7a70e95ee upstream.
If packet headers changed, the cached nfct is no longer relevant
for the packet and attempt to re-use it leads to the incorrect packet
classification.
This issue is causing broken connectivity in OpenStack deployments
with OVS/OVN due to hairpin traffic being unexpectedly dropped.
The setup has datapath flows with several conntrack actions and tuple
changes between them:
actions:ct(commit,zone=8,mark=0/0x1,nat(src)),
set(eth(src=00:00:00:00:00:01,dst=00:00:00:00:00:06)),
set(ipv4(src=172.18.2.10,dst=192.168.100.6,ttl=62)),
ct(zone=8),recirc(0x4)
After the first ct() action the packet headers are almost fully
re-written. The next ct() tries to re-use the existing nfct entry
and marks the packet as invalid, so it gets dropped later in the
pipeline.
Clearing the cached conntrack entry whenever packet tuple is changed
to avoid the issue.
The flow key should not be cleared though, because we should still
be able to match on the ct_state if the recirculation happens after
the tuple change but before the next ct() action.
Cc: stable@vger.kernel.org
Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Reported-by: Frode Nordahl <frode.nordahl@canonical.com>
Link: https://mail.openvswitch.org/pipermail/ovs-discuss/2022-May/051829.html
Link: https://bugs.launchpad.net/ubuntu/+source/ovn/+bug/1967856
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20220606221140.488984-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[Backport to 5.10: minor rebase in ovs_ct_clear function.
This version also applicable to and tested on 5.4 and 4.19.]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cefa91b2332d7009bc0be5d951d6cbbf349f90f8 upstream.
Given a sufficiently large number of actions, while copying and
reserving memory for a new action of a new flow, if next_offset is
greater than MAX_ACTIONS_BUFSIZE, the function reserve_sfa_size() does
not return -EMSGSIZE as expected, but it allocates MAX_ACTIONS_BUFSIZE
bytes increasing actions_len by req_size. This can then lead to an OOB
write access, especially when further actions need to be copied.
Fix it by rearranging the flow action size check.
KASAN splat below:
==================================================================
BUG: KASAN: slab-out-of-bounds in reserve_sfa_size+0x1ba/0x380 [openvswitch]
Write of size 65360 at addr ffff888147e4001c by task handler15/836
CPU: 1 PID: 836 Comm: handler15 Not tainted 5.18.0-rc1+ #27
...
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x5a
print_report.cold+0x5e/0x5db
? __lock_text_start+0x8/0x8
? reserve_sfa_size+0x1ba/0x380 [openvswitch]
kasan_report+0xb5/0x130
? reserve_sfa_size+0x1ba/0x380 [openvswitch]
kasan_check_range+0xf5/0x1d0
memcpy+0x39/0x60
reserve_sfa_size+0x1ba/0x380 [openvswitch]
__add_action+0x24/0x120 [openvswitch]
ovs_nla_add_action+0xe/0x20 [openvswitch]
ovs_ct_copy_action+0x29d/0x1130 [openvswitch]
? __kernel_text_address+0xe/0x30
? unwind_get_return_address+0x56/0xa0
? create_prof_cpu_mask+0x20/0x20
? ovs_ct_verify+0xf0/0xf0 [openvswitch]
? prep_compound_page+0x198/0x2a0
? __kasan_check_byte+0x10/0x40
? kasan_unpoison+0x40/0x70
? ksize+0x44/0x60
? reserve_sfa_size+0x75/0x380 [openvswitch]
__ovs_nla_copy_actions+0xc26/0x2070 [openvswitch]
? __zone_watermark_ok+0x420/0x420
? validate_set.constprop.0+0xc90/0xc90 [openvswitch]
? __alloc_pages+0x1a9/0x3e0
? __alloc_pages_slowpath.constprop.0+0x1da0/0x1da0
? unwind_next_frame+0x991/0x1e40
? __mod_node_page_state+0x99/0x120
? __mod_lruvec_page_state+0x2e3/0x470
? __kasan_kmalloc_large+0x90/0xe0
ovs_nla_copy_actions+0x1b4/0x2c0 [openvswitch]
ovs_flow_cmd_new+0x3cd/0xb10 [openvswitch]
...
Cc: stable@vger.kernel.org
Fixes: f28cd2af22a0 ("openvswitch: fix flow actions reallocation")
Signed-off-by: Paolo Valerio <pvalerio@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f2a3050b4a3e7f32fc0ea3c9b0183090ae00522 ]
'OVS_CLONE_ATTR_EXEC' is an internal attribute that is used for
performance optimization inside the kernel. It's added by the kernel
while parsing user-provided actions and should not be sent during the
flow dump as it's not part of the uAPI.
The issue doesn't cause any significant problems to the ovs-vswitchd
process, because reported actions are not really used in the
application lifecycle and only supposed to be shown to a human via
ovs-dpctl flow dump. However, the action list is still incorrect
and causes the following error if the user wants to look at the
datapath flows:
# ovs-dpctl add-dp system@ovs-system
# ovs-dpctl add-flow "<flow match>" "clone(ct(commit),0)"
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(bad length 4, expected -1 for: action0(01 00 00 00),
ct(commit),0)
With the fix:
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(ct(commit),0)
Additionally fixed an incorrect attribute name in the comment.
Fixes: b233504033db ("openvswitch: kernel datapath clone action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220404104150.2865736-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f19c44452b58a84d95e209b847f5495d91c9983a upstream.
IPv6 nd target mask was not getting populated in flow dump.
In the function __ovs_nla_put_key the icmp code mask field was checked
instead of icmp code key field to classify the flow as neighbour discovery.
ufid:bdfbe3e5-60c2-43b0-a5ff-dfcac1c37328, recirc_id(0),dp_hash(0/0),
skb_priority(0/0),in_port(ovs-nm1),skb_mark(0/0),ct_state(0/0),
ct_zone(0/0),ct_mark(0/0),ct_label(0/0),
eth(src=00:00:00:00:00:00/00:00:00:00:00:00,
dst=00:00:00:00:00:00/00:00:00:00:00:00),
eth_type(0x86dd),
ipv6(src=::/::,dst=::/::,label=0/0,proto=58,tclass=0/0,hlimit=0/0,frag=no),
icmpv6(type=135,code=0),
nd(target=2001::2/::,
sll=00:00:00:00:00:00/00:00:00:00:00:00,
tll=00:00:00:00:00:00/00:00:00:00:00:00),
packets:10, bytes:860, used:0.504s, dp:ovs, actions:ovs-nm2
Fixes: e64457191a25 (openvswitch: Restructure datapath.c and flow.c)
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Link: https://lore.kernel.org/r/20220328054148.3057-1-martinvarghesenokia@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 60b44ca6bd7518dd38fa2719bc9240378b6172c3 ]
During NAT, a tuple collision may occur. When this happens, openvswitch
will make a second pass through NAT which will perform additional packet
modification. This will update the skb data, but not the flow key that
OVS uses. This means that future flow lookups, and packet matches will
have incorrect data. This has been supported since
5d50aa83e2c8 ("openvswitch: support asymmetric conntrack").
That commit failed to properly update the sw_flow_key attributes, since
it only called the ovs_ct_nat_update_key once, rather than each time
ovs_ct_nat_execute was called. As these two operations are linked, the
ovs_ct_nat_execute() function should always make sure that the
sw_flow_key is updated after a successful call through NAT infrastructure.
Fixes: 5d50aa83e2c8 ("openvswitch: support asymmetric conntrack")
Cc: Dumitru Ceara <dceara@redhat.com>
Cc: Numan Siddique <nusiddiq@redhat.com>
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20220318124319.3056455-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01634047bf0d5c2d9b7d8095bb4de1663dbeedeb ]
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4df1b0c24350a0f00229ff895a91f1072bd850d ]
We have observed meters working unexpected if traffic is 3+Gbit/s
with multiple connections.
now_ms is not pretected by meter->lock, we may get a negative
long_delta_ms when another cpu updated meter->used, then:
delta_ms = (u32)long_delta_ms;
which will be a large value.
band->bucket += delta_ms * band->rate;
then we get a wrong band->bucket.
OpenVswitch userspace datapath has fixed the same issue[1] some
time ago, and we port the implementation to kernel datapath.
[1] https://patchwork.ozlabs.org/project/openvswitch/patch/20191025114436.9746-1-i.maximets@ovn.org/
Fixes: 96fbc13d7e77 ("openvswitch: Add meter infrastructure")
Signed-off-by: Tao Liu <thomas.liu@ucloud.cn>
Suggested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d51419d49930be2701c2633ae271b350397c3ca ]
'struct ovs_zone_limit' has more members than initialized in
ovs_ct_limit_get_default_limit(). The rest of the memory is a random
kernel stack content that ends up being sent to userspace.
Fix that by using designated initializer that will clear all
non-specified fields.
Fixes: 11efd5cb04a1 ("openvswitch: Support conntrack zone limit")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43c13605bad44b8abbc9776d6e63f62ccb7a47d6 ]
when openvswitch is configured to mangle the LSE, the current value is
read from the packet dereferencing 4 bytes at mpls_hdr(): ensure that
the label is contained in the skb "linear" area.
Found by code inspection.
Fixes: d27cf5c59a12 ("net: core: add MPLS update core helper and use in OvS")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/aa099f245d93218b84b5c056b67b6058ccf81a66.1606987185.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa7b526dc0b5dbf40c1b834d76a667ad672a410 upstream.
With multiple DNAT rules it's possible that after destination
translation the resulting tuples collide.
For example, two openvswitch flows:
nw_dst=10.0.0.10,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
nw_dst=10.0.0.20,tp_dst=10, actions=ct(commit,table=2,nat(dst=20.0.0.1:20))
Assuming two TCP clients initiating the following connections:
10.0.0.10:5000->10.0.0.10:10
10.0.0.10:5000->10.0.0.20:10
Both tuples would translate to 10.0.0.10:5000->20.0.0.1:20 causing
nf_conntrack_confirm() to fail because of tuple collision.
Netfilter handles this case by allocating a null binding for SNAT at
egress by default. Perform the same operation in openvswitch for DNAT
if no explicit SNAT is requested by the user and allocate a null binding
for SNAT for packets in the "original" direction.
Reported-at: https://bugzilla.redhat.com/1877128
Suggested-by: Florian Westphal <fw@strlen.de>
Fixes: 05752523e565 ("openvswitch: Interface with NAT.")
Signed-off-by: Dumitru Ceara <dceara@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 659d4587fe7233bfdff303744b20d6f41ad04362 ]
Compile the kernel for arm 32 platform, the build warning found.
To fix that, should use div_u64() for divisions.
| net/openvswitch/meter.c:396: undefined reference to `__udivdi3'
[add more commit msg, change reported tag, and use div_u64 instead
of do_div by Tonghao]
Fixes: e57358873bb5d6ca ("net: openvswitch: use u64 for meter bucket")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57358873bb5d6caa882b9684f59140912b37dde ]
When setting the meter rate to 4+Gbps, there is an
overflow, the meters don't work as expected.
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9aba6c5b49254d5bee927d81593ed4429e91d4ae ]
ovs_ct_put_key() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 3-byte hole at the end
of `struct ovs_key_ct_tuple_ipv4` and `struct ovs_key_ct_tuple_ipv6`. Fix
it by initializing `orig` with memset().
Fixes: 9dd7f8907c37 ("openvswitch: Add original direction conntrack tuple to sw_flow_key.")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17843655708e1941c0653af3cd61be6948e36f43 ]
ovs connection tracking module performs de-fragmentation on incoming
fragmented traffic. Take info account if traffic has been de-fragmented
in execute_check_pkt_len action otherwise we will perform the wrong
nested action considering the original packet size. This issue typically
occurs if ovs-vswitchd adds a rule in the pipeline that requires connection
tracking (e.g. OVN stateful ACLs) before execute_check_pkt_len action.
Moreover take into account GSO fragment size for GSO packet in
execute_check_pkt_len routine
Fixes: 4d5ec89fc8d14 ("net: openvswitch: Add a new action check_pkt_len")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4c76bf696a608ea5cc555fe97ec59a9033236604 ]
Unlocking of a not locked mutex is not allowed.
Other kernel thread may be in critical section while
we unlock it because of setting user_feature fail.
Fixes: 95a7233c4 ("net: openvswitch: Set OvS recirc_id from tc chain index")
Cc: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04ac224b1688f005a84f764cfe29844f8e9da08 ]
The skb_mpls_push was not updating ethertype of an ethernet packet if
the packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to
port 7 is an l3 device (ARPHRD_NONE) the skb_mpls_push function does
not update the ethertype of the packet even though the previous
push_eth action had added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x0800),ipv4(tos=0/0xfc,ttl=64,frag=no),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
push_mpls(label=13,tc=0,ttl=64,bos=1,eth_type=0x8847),4
Fixes: 8822e270d697 ("net: core: move push MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 040b5cfbcefa263ccf2c118c4938308606bb7ed8 ]
The skb_mpls_pop was not updating ethertype of an ethernet packet if the
packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to port 7
is an l3 device (ARPHRD_NONE) the skb_mpls_pop function does not update
the ethertype of the packet even though the previous push_eth action had
added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x8847),
mpls(label=12/0xfffff,tc=0/0,ttl=0/0x0,bos=1/1),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
pop_mpls(eth_type=0x800),4
Fixes: ed246cee09b9 ("net: core: move pop MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d50aa83e2c8e91ced2cca77c198b468ca9210f4 ]
The openvswitch module shares a common conntrack and NAT infrastructure
exposed via netfilter. It's possible that a packet needs both SNAT and
DNAT manipulation, due to e.g. tuple collision. Netfilter can support
this because it runs through the NAT table twice - once on ingress and
again after egress. The openvswitch module doesn't have such capability.
Like netfilter hook infrastructure, we should run through NAT twice to
keep the symmetry.
Fixes: 05752523e565 ("openvswitch: Interface with NAT.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a574f86652a4540a2433946ba826ccb87f398cc ]
If we can't build the flow del notification, we can simply delete
the flow, no need to crash the kernel. Still keep a WARN_ON to
preserve debuggability.
Note: the BUG_ON() predates the Fixes tag, but this change
can be applied only after the mentioned commit.
v1 -> v2:
- do not leak an skb on error
Fixes: aed067783e50 ("openvswitch: Minimize ovs_flow_cmd_del critical section.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ffeb03fbba3b599690b361467bfd2373e8c450f ]
All the callers of ovs_flow_cmd_build_info() already deal with
error return code correctly, so we can handle the error condition
in a more gracefull way. Still dump a warning to preserve
debuggability.
v1 -> v2:
- clarify the commit message
- clean the skb and report the error (DaveM)
Fixes: ccb1352e76cf ("net: Add Open vSwitch kernel components.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4e81c0b3fa93d07653e2415fa71656b080a112fd ]
When user-space sets the OVS_UFID_F_OMIT_* flags, and the relevant
flow has no UFID, we can exceed the computed size, as
ovs_nla_put_identifier() will always dump an OVS_FLOW_ATTR_KEY
attribute.
Take the above in account when computing the flow command message
size.
Fixes: 74ed7ab9264c ("openvswitch: Add support for unique flow IDs.")
Reported-by: Qi Jun Ding <qding@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.
Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.
In most cases, GFP_KERNEL is fine. The exceptions are:
* openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
indirectly call rtnl_net_notifyid() from RCU critical section,
* rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
parameter.
Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.
Found by code inspection.
Fixes: 9a9634545c70 ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
the following script:
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress protocol ip matchall \
> action mpls push protocol mpls_uc label 0x355aa bos 1
causes corruption of all IP packets transmitted by eth0. On TC egress, we
can't rely on the value of skb->mac_len, because it's 0 and a MPLS 'push'
operation will result in an overwrite of the first 4 octets in the packet
L2 header (e.g. the Destination Address if eth0 is an Ethernet); the same
error pattern is present also in the MPLS 'pop' operation. Fix this error
in act_mpls data plane, computing 'mac_len' as the difference between the
network header and the mac header (when not at TC ingress), and use it in
MPLS 'push'/'pop' core functions.
v2: unbreak 'make htmldocs' because of missing documentation of 'mac_len'
in skb_mpls_pop(), reported by kbuild test robot
CC: Lorenzo Bianconi <lorenzo@kernel.org>
Fixes: 2a2ea50870ba ("net: sched: add mpls manipulation actions to TC")
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 174e23810cd31
("sk_buff: drop all skb extensions on free and skb scrubbing") made napi
recycle always drop skb extensions. The additional skb_ext_del() that is
performed via nf_reset on napi skb recycle is not needed anymore.
Most nf_reset() calls in the stack are there so queued skb won't block
'rmmod nf_conntrack' indefinitely.
This removes the skb_ext_del from nf_reset, and renames it to a more
fitting nf_reset_ct().
In a few selected places, add a call to skb_ext_reset to make sure that
no active extensions remain.
I am submitting this for "net", because we're still early in the release
cycle. The patch applies to net-next too, but I think the rename causes
needless divergence between those trees.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
userspace openvswitch patch "(dpif-linux: Implement the API
functions to allow multiple handler threads read upcall)"
changes its type from U32 to UNSPEC, but leave the kernel
unchanged
and after kernel 6e237d099fac "(netlink: Relax attr validation
for fixed length types)", this bug is exposed by the below
warning
[ 57.215841] netlink: 'ovs-vswitchd': attribute type 5 has an invalid length.
Fixes: 5cd667b0a456 ("openvswitch: Allow each vport to have an array of 'port_id's")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offloaded OvS datapath rules are translated one to one to tc rules,
for example the following simplified OvS rule:
recirc_id(0),in_port(dev1),eth_type(0x0800),ct_state(-trk) actions:ct(),recirc(2)
Will be translated to the following tc rule:
$ tc filter add dev dev1 ingress \
prio 1 chain 0 proto ip \
flower tcp ct_state -trk \
action ct pipe \
action goto chain 2
Received packets will first travel though tc, and if they aren't stolen
by it, like in the above rule, they will continue to OvS datapath.
Since we already did some actions (action ct in this case) which might
modify the packets, and updated action stats, we would like to continue
the proccessing with the correct recirc_id in OvS (here recirc_id(2))
where we left off.
To support this, introduce a new skb extension for tc, which
will be used for translating tc chain to ovs recirc_id to
handle these miss cases. Last tc chain index will be set
by tc goto chain action and read by OvS datapath.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first fragment in a datagram contains the L4 headers. When the
Open vSwitch module parses a packet, it always sets the IP protocol
field in the key, but can only set the L4 fields on the first fragment.
The original behavior would not clear the L4 portion of the key, so
garbage values would be sent in the key for "later" fragments. This
patch clears the L4 fields in that circumstance to prevent sending those
garbage values as part of the upcall.
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP fragments are reassembled before being sent to conntrack, the
key from the last fragment is used. Unless there are reordering
issues, the last fragment received will not contain the L4 ports, so the
key for the reassembled datagram won't contain them. This patch updates
the key once we have a reassembled datagram.
The handle_fragments() function works on L3 headers so we pull the L3/L4
flow key update code from key_extract into a new function
'key_extract_l3l4'. Then we add a another new function
ovs_flow_key_update_l3l4() and export it so that it is accessible by
handle_fragments() for conntrack packet reassembly.
Co-authored-by: Justin Pettit <jpettit@ovn.org>
Signed-off-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a conntrack cache issue with timeout policy.
Currently, we do not check if the timeout extension is set properly in the
cached conntrack entry. Thus, after packet recirculate from conntrack
action, the timeout policy is not applied properly. This patch fixes the
aforementioned issue.
Fixes: 06bd2bdf19d2 ("openvswitch: Add timeout support to ct action")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 06bd2bdf19d2 ("openvswitch: Add timeout support to ct action")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in function ovs_dp_process_packet(), return values of
ovs_execute_actions() are silently discarded. This patch prints out
an debug message when error happens so as to provide helpful hints
for debugging.
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
