IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 85b8350ae99d1300eb6dc072459246c2649a8e50 upstream.
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666b7 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 656ab1bdcd2b755dc161a9774201100d5bf74b8d ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: a2c6e82e5341 ("ARM: dts: meson: switch to the generic Ethernet PHY reset bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # on Odroid-C1+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/ff78772b306411e145769c46d4090554344db41e.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b5dcc8d427e2bcb84c49eb03ffefe11e7537a55 ]
Due to strobe signal not being propagated from CPU to securam
the securam needs to be mapped as device or strongly ordered memory
to work properly. Otherwise, updating to one offset may affect
the adjacent locations in securam.
Fixes: d4ce5f44d4409 ("ARM: dts: at91: sama5d2: Add securam node")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 851a95da583c26e2ddeb7281e9b61f0d76ea5aba ]
The triggers for the ADC were taken from at91sam9260 dtsi but are not
correct.
Fixes: a4c1d6c75822 ("ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-10-alexandre.belloni@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f24479ead579459106bb55c2320a000135731f9 ]
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba87708 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1062fa7292f1e3744db0a487c4ac0109e09b03d ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: b7c2b61570798 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-4-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be4dd2d448816a27c1446f8f37fce375daf64148 ]
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
Fixes: 38153a017896f ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201118120019.1257580-3-cristian.birsan@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e1cc9679776f5b9e42481d392b1550753ebd084 ]
The VGA memory region is always from the top of RAM. On this board, that
is 0x80000000 + 0x20000000 - 0x01000000 = 0x9f000000.
This was not an issue in practice as the region is "reserved" by the
vendor's u-boot reducing the amount of available RAM, and the only user
is the host VGA device poking at RAM over PCIe. That is, nothing from
the ARM touches it.
It is worth fixing as developers copy existing device trees when
building their machines, and the XDMA driver does use the memory region
from the ARM side.
Fixes: c4043ecac34a ("ARM: dts: aspeed: Add S2600WF BMC Machine")
Reported-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20200922064234.163799-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bd7e7ff56feea7810df900fb09c9741d259861d9 upstream.
On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD). LDO7 also supplies
GPJ GPIO pins.
The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.
Fixes: 88644b4c750b ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-3-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d992fd8f4e0f09c980726308d2f2725587b32d6 upstream.
The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs. This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).
Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes. This also fixes over-current warning:
[ 6.024658] usb usb4-port1: over-current condition
[ 6.028271] usb usb3-port1: over-current condition
Fixes: cb0896562228 ("ARM: dts: exynos: Add USB to Exynos5410")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-2-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecc1ff532b499d20304a4f682247137025814c34 upstream.
On Odroid XU board the USB3-0 port is a microUSB and USB3-1 port is USB
type A (host). The roles were copied from Odroid XU3 (Exynos5422)
design which has it reversed.
Fixes: 8149afe4dbf9 ("ARM: dts: exynos: Add initial support for Odroid XU board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201015182044.480562-1-krzk@kernel.org
Tested-by: Gabriel Ribba Esteva <gabriel.ribbae@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 58d6bca5efc73235b0f84c0d53321737177c651e ]
Since commit 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera
support") the PAD_GPIO_6 is used for providing the camera sensor clock.
Remove it from the enetgrp to fix the following IOMXU conflict:
[ 9.972414] imx6q-pinctrl 20e0000.pinctrl: pin MX6Q_PAD_GPIO_6 already requested by 2188000.ethernet; cannot claim for 1-003c
[ 9.983857] imx6q-pinctrl 20e0000.pinctrl: pin-140 (1-003c) status -22
[ 9.990514] imx6q-pinctrl 20e0000.pinctrl: could not request pin 140 (MX6Q_PAD_GPIO_6) from group ov5645grp on device 20e0000.pinctrl
Fixes: 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7361b9c4615951f52ffd2b1afa09a1384c7b4e4 ]
The RX/TX delays for the Ethernet PHY on the Linksprite pcDuino 3 Nano
are configured in hardware, using resistors that are populated to pull
the RTL8211E's RXDLY/TXDLY pins low or high as needed.
phy-mode should be set to rgmii-id to reflect this. Previously it was
set to rgmii, which used to work but now results in the delays being
disabled again as a result of the bugfix in commit bbc4d71d6354 ("net:
phy: realtek: fix rtl8211e rx/tx delay config").
Tested on two pcDuino 3 Nano boards purchased in 2015. Without this fix,
Ethernet works unreliably on one board and doesn't work at all on the
other.
Fixes: 061035d456c9 ("ARM: dts: sun7i: Add dts file for pcDuino 3 Nano board")
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201123174739.6809-1-ats@offog.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a98fd117a2553ab1a6d2fe3c7acae88c1eca4372 ]
Currently the GIC node in V3s DTSI follows some old DT examples, and
being broken. This leads a warning at boot.
Fix this.
Fixes: f989086ccbc6 ("ARM: dts: sunxi: add dtsi file for V3s SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201120050851.4123759-1-icenowy@aosc.io
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd5cdcdc66e1f7179ff6d172d1e5f55e43403aa8 ]
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: 23edc168bd98 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry")
Fixes: 27e81e1970a8 ("ARM: dts: sun8i: v40: bananapi-m2-berry: Enable GMAC ethernet controller")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326755-39742-1-git-send-email-pgreco@centosproject.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c9cb4094ccf242eddd140efba13872c55f68a87 ]
The Ethernet PHY on the Bananapi M1 has the RX and TX delays enabled on
the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8a5b272fbf44 ("ARM: dts: sun7i: Add Banana Pi board")
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/1604326600-39544-1-git-send-email-pgreco@centosproject.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05d5de6ba7dbe490dd413b5ca11d0875bd2bc006 ]
According to the bosch,m_can.yaml bindings the first clock shall be the "hclk",
while the second clock "cclk".
This patch fixes the order accordingly.
Fixes: 0adbe832f21a ("ARM: dts: dra76x: Add MCAN node")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 33d0d843872c5ddbe28457a92fc6f2487315fb9f ]
The SPI chip selects are represented as:
cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
, which means that they are used in GPIO function instead of native
SPI mode.
Fix the IOMUX for the chip select 1 to use GPIO4_13 instead of
the native CSPI_SSI function.
Fixes: c605cbf5e135 ("ARM: dts: imx: add device tree support for Freescale imx50evk board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3914160ffc0bf762d6d605d4b27036b7b89367ea ]
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8c7ba536e709 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: aa8fee415f46 ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1064037e8ecf09d587b7b4966eebe0c362908e5 ]
The Ethernet PHY on the Cubieboard 4 and A80 Optimus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 98048143b7f8 ("ARM: dts: sun9i: cubieboard4: Enable GMAC")
Fixes: bc9bd03a44f9 ("ARM: dts: sun9i: a80-optimus: Enable GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-7-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57dbe558457bf4042169bc1f334e3b53a8480a1c ]
The Ethernet PHY on the Bananapi M3 and Cubietruck Plus have the RX
and TX delays enabled on the PHY, using pull-ups on the RXDLY and
TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 039359948a4b ("ARM: dts: sun8i: a83t: Enable Ethernet on two boards")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-6-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e080ab31a0aa126b0a7e4f67f2b01b371b852c88 ]
The Ethernet PHY on the Orange Pi Plus 2E has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: 7a78ef92cdc5 ("ARM: sun8i: h3: Enable EMAC with external PHY on Orange Pi Plus 2E")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-5-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f94f78bd93f567c022f594589dbeecdf59931365 ]
The Ethernet PHY on the Bananapi M1+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 04c85ecad32a ("ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-4-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 353c3de1303fc93032164402c0eb8550ecd6f154 ]
The Ethernet PHY on the Cubietruck has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 67073d97672d ("ARM: dts: sun7i: cubietruck: Enable the GMAC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Emilio López <emilio@elopez.com.ar>
Reviewed-by: Emilio López <emilio@elopez.com.ar>
Link: https://lore.kernel.org/r/20201024162515.30032-3-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e76724153f5b4539802cc21b2c6131058668a1c6 ]
The Ethernet PHY on the A31 Hummingbird has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: c220aec2bb79 ("ARM: dts: sun6i: Add Merrii A31 Hummingbird support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-2-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d80e2f00a42ef10b54e1b2d9e97314f8fd046c0 ]
This reverts commit 75ee680cbd2e4d0156b94f9fec50076361ab12f2.
Turns out the activity and link LEDs on the RJ45 port are active low,
just like on the Orange Pi PC.
Revert the commit that says otherwise.
Fixes: 75ee680cbd2e ("arm: sun8i: orangepi-pc-plus: Set EMAC activity LEDs to active high")
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-1-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dea252fa41cd8ce332d148444e4799235a8a03ec ]
When running dtbs_check thermal_zone warn about the
temperature declared.
thermal-zones: cpu-thermal:trips:cpu-alert0:temperature:0:0: 850000 is greater than the maximum of 200000
It's indeed wrong the real value is 85°C and not 850°C.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201003100332.431178-1-peron.clem@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c17a2974abf68a58517f75741b15c4aba42b4b8 ]
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-9-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb98fff84ad1ea321823759edaba573a16fa02bd ]
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d38cae370e5f2094cbc38db3082b8e9509ae52ce ]
The fixed clocks are kept under dedicated 'external-clocks' node, thus a
fake 'reg' was added. This is not correct with dtschema as fixed-clock
binding does not have a 'reg' property. Moving fixed clocks out of
'soc' to root node fixes multiple dtbs_check warnings:
external-clocks: $nodename:0: 'external-clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
external-clocks: #size-cells:0:0: 0 is not one of [1, 2]
external-clocks: oscillator@0:reg:0: [0] is too short
external-clocks: oscillator@1:reg:0: [1] is too short
external-clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea4e792f3c8931fffec4d700cf6197d84e9f35a6 ]
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-6-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19d3e9a0bdd57b90175f30390edeb06851f5f9f3 ]
We currently have a different clock rate for droid4 compared to the
stock v3.0.8 based Android Linux kernel:
# cat /sys/kernel/debug/clk/dpll_*_m7x2_ck/clk_rate
266666667
307200000
# cat /sys/kernel/debug/clk/l3_gfx_cm:clk:0000:0/clk_rate
307200000
Let's fix this by configuring sgx to use 153.6 MHz instead of 307.2 MHz.
Looks like also at least duover needs this change to avoid hangs, so
let's apply it for all 4430.
This helps a bit with thermal issues that seem to be related to memory
corruption when using sgx. It seems that other driver related issues
still remain though.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 737e7610b545cc901a9696083c1824a7104b8d1b ]
The 3.10 vendor kernel defines the following GPU 20 interrupt lines:
#define INT_MALI_GP AM_IRQ(160)
#define INT_MALI_GP_MMU AM_IRQ(161)
#define INT_MALI_PP AM_IRQ(162)
#define INT_MALI_PMU AM_IRQ(163)
#define INT_MALI_PP0 AM_IRQ(164)
#define INT_MALI_PP0_MMU AM_IRQ(165)
#define INT_MALI_PP1 AM_IRQ(166)
#define INT_MALI_PP1_MMU AM_IRQ(167)
#define INT_MALI_PP2 AM_IRQ(168)
#define INT_MALI_PP2_MMU AM_IRQ(169)
#define INT_MALI_PP3 AM_IRQ(170)
#define INT_MALI_PP3_MMU AM_IRQ(171)
#define INT_MALI_PP4 AM_IRQ(172)
#define INT_MALI_PP4_MMU AM_IRQ(173)
#define INT_MALI_PP5 AM_IRQ(174)
#define INT_MALI_PP5_MMU AM_IRQ(175)
#define INT_MALI_PP6 AM_IRQ(176)
#define INT_MALI_PP6_MMU AM_IRQ(177)
#define INT_MALI_PP7 AM_IRQ(178)
#define INT_MALI_PP7_MMU AM_IRQ(179)
However, the driver from the 3.10 vendor kernel does not use the
following four interrupt lines:
- INT_MALI_PP3
- INT_MALI_PP3_MMU
- INT_MALI_PP7
- INT_MALI_PP7_MMU
Drop the "pp3" and "ppmmu3" interrupt lines. This is also important
because there is no matching entry in interrupt-names for it (meaning
the "pp2" interrupt is actually assigned to the "pp3" interrupt line).
Fixes: 7d3f6b536e72c9 ("ARM: dts: meson8: add the Mali-450 MP6 GPU")
Reported-by: Thomas Graichen <thomas.graichen@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: thomas graichen <thomas.graichen@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200815181957.408649-1-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3658a2b7f3e16c7053eb8d70657b94bb62c5a0f4 ]
DCDC1 regulator powers many different subsystems. While some of them can
work at 3.0 V, some of them can not. For example, VCC-HDMI can only work
between 3.24 V and 3.36 V. According to OS images provided by the board
manufacturer this regulator should be set to 3.3 V.
Set DCDC1 and DCDC1SW to 3.3 V in order to fix this.
Fixes: da7ac948fa93 ("ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200824193649.978197-1-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 82ffb35c2ce63ef8e0325f75eb48022abcf8edbe ]
rng DT node was added without a compatible string.
i.MX driver for RNGC (drivers/char/hw_random/imx-rngc.c) also claims
support for RNGB, and is currently used for i.MX25.
Let's use this driver also for RNGB block in i.MX6SL.
Fixes: e29fe21cff96 ("ARM: dts: add device tree source for imx6sl SoC")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29c623d64f0dcd6aa10e0eabd16233e77114090b ]
Since $(NM) variable can be easily overridden for the whole build, it's
better to use it instead of $(CROSS_COMPILE)nm. The use of $(CROSS_COMPILE)
prefixed variables where their calculated equivalents can be used is
incorrect. This fixes issues with builds where $(NM) is set to llvm-nm.
Link: https://github.com/ClangBuiltLinux/linux/issues/766
Signed-off-by: Dmitry Golovin <dima@golovin.in>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Matthias Maennich <maennich@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b793dab8d811e103665d6bddaaea1c25db3776eb ]
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 1c8f40650723 ("ARM: dts: BCM5301X: convert to iProc QSPI")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1ecc40a954fd0f5e3789b91fa80f15e82284e39 ]
The string was incorrectly defined before from least to most
specific, swap the compatible strings accordingly.
Fixes: 329f98c1974e ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d663186293a818af97c648624bee6c7a59e8218b ]
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: b9099ec754b5 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81dbbb417da4d1ac407dca5b434d39d5b6b91ef3 ]
According to the Reference Manual, the correct size is 512 MiB.
Without this fix, probing the QSPI fails:
fsl-quadspi 1550000.spi: ioremap failed for resource
[mem 0x40000000-0x7fffffff]
fsl-quadspi 1550000.spi: Freescale QuadSPI probe failed
fsl-quadspi: probe of 1550000.spi failed with error -12
Fixes: 85f8ee78ab72 ("ARM: dts: ls1021a: Add support for QSPI with ls1021a SoC")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
