IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This time there is one fix for the error path in the mediatek cmdq driver
(used by their video driver) and a couple of devicetree fixes, mostly
for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers,
one of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for
v5.8 with a cc:stable tag, so I ended up picking them up
here as well
- The Mediatek Video Codec needs to run at a higher frequency
than configured originally
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=E8Pg
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This time there is one fix for the error path in the mediatek cmdq
driver (used by their video driver) and a couple of devicetree fixes,
mostly for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers, one
of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for v5.8
with a cc:stable tag, so I ended up picking them up here as well
- The Mediatek Video Codec needs to run at a higher frequency than
configured originally"
* tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
ARM: dts/imx6q-bx50v3: Set display interface clock parents
soc: mediatek: cmdq: return send msg error code
arm64: dts: mt8173: fix vcodec-enc clock
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
-----BEGIN PGP SIGNATURE-----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=dAx4
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- correct value of decompressor tag size in header
- fix DACR value when we have nested exceptions
- fix a missing newline on a kernel message
- fix mask for ptrace thumb breakpoint hook
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8977/1: ptrace: Fix mask for thumb breakpoint hook
ARM: 8973/1: Add missing newline terminator to kernel message
ARM: uaccess: fix DACR mismatch with nested exceptions
ARM: uaccess: integrate uaccess_save and uaccess_restore
ARM: uaccess: consolidate uaccess asm to asm/uaccess-asm.h
ARM: 8970/1: decompressor: increase tag size
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl68I9MRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXO2/Q/+IiBtpAgZ1Y5XCXjfmBOGF5H5DKtSK7xd
pOVqkRq6N0akGOuwLWaI9CHoJnEZ1VUMQZzBbZjCia640BeGvyM7rEs8ffCmvlqa
aLRwDAV3+mg0D4M5TyElLqAc5a3pNBDmOvyUCgXAql6wy2tLdkzC+P8K+LaFltPW
05j/jfLM5EOvfRPxX0xvz+qZYTiKeOw5GZosGz2MwRAemSFy5EWm9yTqyO+exJm3
IMWkdwR9TBgkf8FE+QhuhnVIS+VmXT5VVFgAEcYWCmAOjvbPONFeumjKJNxTEgpf
/IzuAE5FRr+d7OqPcHV8XFhsfw2NlyKmyqzdm+RTzV4RosmsU9c8rdkV/vqWfKbO
oVw5DHFT20jRRCcFGJp81yMaeo6KPPe8X5l+0/DeyC0ai4Vq/eQKlJaB3LOsYJSa
FUjyrCex8d2n2qQlkuXRCkIj259wPFtjFbgwQBzgYD33KEpOLlNseLMV3Qa8E63S
qCZTAQs2rlEjJgmdByZ38Pjcu+Rq/qhwG12+73oF8tQmoNf+VSKVrfbki4Q5Ne37
L8TvQFWODeE5aUu+MYRQKMDvMd6ufUtUDQLOSIO+pd0C5fDcaxUFT9kOvlM/zBW+
b2AcggtPOeNFtoJK7V2Z4IpnqSdZyX+sPpUPLRZZr0V21bw22Gw6WLu0izMdPqWE
mrzCYrDSy0k=
=tWSS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few cpsw related dts fixes for omaps
Recent cpsw driver changes exposed few regressions in the cpsw related
dts configuration that would be good to fix:
- Few more boards still need to be updated to use rgmii-rxid phy caused
by the fallout from commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY" as the rx delay is now disabled unless we
use rgmii-rxid.
- On dm814x we have been using a wrong clock for mdio that now can produce
external abort on some boards
* tag 'omap-for-v5.7/cpsw-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
Link: https://lore.kernel.org/r/pull-1589472123-367692@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
-----BEGIN PGP SIGNATURE-----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=klA0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Vincent fixes the polarity of the ACT LED on the Raspberry Pi Zero W
board
- Hamish fixes the ARM PPI interrupts sensitivy for the Hurricane 2
SoCs
* tag 'arm-soc/for-5.7/devicetree-fixes-part2-v2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
Link: https://lore.kernel.org/r/20200524203714.17035-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl7Glo8UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5L1wf9ErUGnk73syGW6Hhr8VRRGocK8Zj7
Skh0E2k1ZT0YXRn5h6dikZw9TsR8IVt5CSt57NxvR61i4PnPm8PEBZdIl80kMu3P
3wO28Z4oIqhi9tzI+fM6uRV6WGxp5fIuwyEghAPpv0Xo/XKDbDQZkk/TtQDhqvVC
n7rjgk+N/x6kVTfRTYYIvI+XSoGM1lGdBl9DdAxKc2Suxr27qFcopYIE6JKsapoo
0khguE7v8BNG+N7iJ6tDXRcn4MV1TEDpTQ0cwZr1zIAiA3P5ZYKIGdweScVJ80fa
RGllUMBBrs7r0cNTpA8hu76omF2Kim0D8QsvLMDLELOijB4b/qBf2bU9AA==
=cAJG
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.7, round 2:
One imx6q-bx50v3 device tree change to fix an issue, attempting atomic
modeset while using HDMI and display port at the same time causes LDB
clock programming to destroy the programming of HDMI.
* tag 'imx-fixes-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts/imx6q-bx50v3: Set display interface clock parents
Link: https://lore.kernel.org/r/20200521150719.GB24084@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These three fixes should make it into linux-5.7 and
also into the branch for other mmp dt changes for v5.8,
so I created a branch for them.
* mmp/fixes:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"usb-nop-xceiv" is good enough if we don't lose the configuration done
by the firmware, but we'd really prefer a real driver.
Unfortunately, the PHY core is odd in that when the node is compatible
with "usb-nop-xceiv", it ignores the other compatible strings. Let's
just remove it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I've managed to get about everything wrong while digging these out of
OEM's board file.
Correct the bus numbers, the exact model of the NOR flash, polarity of
the chip selects and align the SPI frequency with the data sheet.
Tested that it works now, with a slight fix to the PXA SSP driver.
Link: https://lore.kernel.org/r/20200419171157.672999-16-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Clocks are in fact slightly different on MMP3. In particular, PLL2 is
fixed to a different frequency, there's an extra PLL3, and the GPU
clocks are configured differently.
Link: https://lore.kernel.org/r/20200419171157.672999-15-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a1e
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754b5 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXr5jTgAKCRCKwlD9ZEnx
cKSMAQCGIyrVtXHISZSFlp3poR1bBMejfxvZWmLIBzIPSw28SQEAqGTxP7dONrXY
JIbYmduRiRfWK6h0ghr769xp/KQPIAQ=
=dl06
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.7 (take two)
- Fix a wrong clock configuration on R-Mobile A1,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: iwg20d-q7-dbcm-ca: Remove unneeded properties in hdmi@39
ARM: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
arm64: dts: renesas: Make hdmi encoder nodes compliant with DT bindings
ARM: dts: r8a7740: Add missing extal2 to CPG node
Link: https://lore.kernel.org/r/20200515125043.22811-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the adi,input-style and adi,input-justification properties of
hdmi@39 to make it compliant with the "adi,adv7511w" DT binding.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-6-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
-----BEGIN PGP SIGNATURE-----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=umsu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.6-rc cycle
Few device tree fixes for various devices:
- A regression fix for non-existing can device on am534x-idk
- Fix missing dma-ranges for dra7 pcie
- Fix flakey wlan on droid4 where some devices would not connect
at all because of internal pull being used with an external pull
- Fix occasional missed wake-up events on droid4 modem uart
* tag 'omap-for-v5.6/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix occasional lost wakeirq for uart1
ARM: dts: omap4-droid4: Fix flakey wlan by disabling internal pull for gpio
ARM: dts: dra7: Fix bus_dma_limit for PCIe
ARM: dts: am574x-idk: Disable m_can node
Link: https://lore.kernel.org/r/pull-1588872844-804667@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
make dtc and the new dtscheck against yaml bindings happy.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAl6yA9QQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeX0CACEwXPa8ChfXg+N4846D/wcwkpMVQqnTbMR
WrnqVLUNHf71h7Yej/aXpBSgEq5er1Q/HVgbjvkAAYNw633MNWgaNMi9AFl03gTF
uSOSUoiwauUUlvWt2aZ44IHxHS/WC0FB9/wIROpnD0SJvmYX9MJF8AVITNDsTDGv
EsSswwAXiBxILDWWdBM2QgAZxEhan3MwBbHQrmPRePDAWylluT3tMGjEfLgIapcW
9w44tw0kR8g7Zwgq+MYcfyHoNhUXOr1iMlCCA0LWOOtNBJAbXKM4XDp4cWwHLiI3
nktZSWXN7B08dx4hi/++18izC6N/ZwoGycMN4wG9kvdaRnpwh3KN
=vkl2
-----END PGP SIGNATURE-----
Merge tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Some fixes for the newly added Pinebook Pro and other fixes to
make dtc and the new dtscheck against yaml bindings happy.
* tag 'v5.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix pinctrl sub nodename for spi in rk322x.dtsi
arm64: dts: rockchip: Fix Pinebook Pro FUSB302 interrupt
ARM: dts: rockchip: swap clock-names of gpu nodes
arm64: dts: rockchip: swap interrupts interrupt-names rk3399 gpu node
arm64: dts: rockchip: fix status for &gmac2phy in rk3328-evb.dts
arm64: dts: rockchip: remove extra assigned-clocks property from &gmac2phy node in rk3328-evb.dts
ARM: dts: rockchip: fix phy nodename for rk3229-xms6
ARM: dts: rockchip: fix phy nodename for rk3228-evb
arm64: dts: rockchip: Rename dwc3 device nodes on rk3399 to make dtc happy
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3399 pmugrf node
arm64: dts: rockchip: drop #address-cells, #size-cells from rk3328 grf node
arm64: dts: rockchip: drop non-existent gmac2phy pinmux options from rk3328
arm64: dts: rockchip: Replace RK805 PMIC node name with "pmic" on rk3328 boards
arm64: dts: rockchip: enable DC charger detection pullup on Pinebook Pro
arm64: dts: rockchip: fix inverted headphone detection on Pinebook Pro
arm64: dts: rockchip: Correct PMU compatibles for PX30 and RK3308
Link: https://lore.kernel.org/r/1738941.6LdaBJIBqS@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXqqEEQAKCRCKwlD9ZEnx
cK6VAQDEYT5s4bzgLANPkTuvz3n5NgmS1nSC9tGrUX9co4OEUgD+OkwEnFJgLF1+
LbwisW1fNfCz1looPeyyZTl9Q8o5Yg0=
=cIRT
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.7
- Fix IOMMU support on R-Car V3H,
- Minor fixes that are fast-tracked to avoid introducing regressions
during conversion of DT bindings to json-schema.
* tag 'renesas-fixes-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r7s9210: Remove bogus clock-names from OSTM nodes
arm64: dts: renesas: r8a77980: Fix IPMMU VIP[01] nodes
ARM: dts: r8a73a4: Add missing CMT1 interrupts
Link: https://lore.kernel.org/r/20200430084834.1384-1-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl6pHtIUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM69sAgAp/H4BASI7SAbrjYsFjCP+ymPVgeS
Y9oeLm09Q2XEF6GiRhK4SDqN56BOUelRI6nqWx3k6sU5A7SuZMqGSaZZEhCtHhjl
iixyxSccxh4prUWSEDQPHyIJ6yjBt+QkKhycOVLwq7FFLdlrSaRuameNQAkjEU4a
YPSL0oBd1xNbz75RaqgmyI0lzOuQg1P+GMQqmVOYfrucK94bq62FMSezyEBQxKU+
0MVG/hEkeLtxFgzE6OpkBs1p1m+KgXE7qvV0W84VyZOKgri1qJ74V1Pl/RJNNVA0
p46c3PH66OATAU7+pbshC0x/hsN8ZVAoBhPit5oLF7ugDNpi377jT/zRrw==
=z3sI
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.7:
- Set correct AHB clock for i.MX8MN SDMA1 device to fix a "Timeout
waiting for CH0" error.
- Fix a linker error for i.MX6 configurations that have ARM_CPU_SUSPEND=n,
which can happen if neither CONFIG_PM, CONFIG_CPU_IDLE, nor ARM_PSCI_FW
are selected.
- Fix I2C1 pinctrl configuration for i.MX27 phytec-phycard board.
- Fix i.MX8M AIPS 'reg' properties to remove DTC simple_bus_reg
warnings.
- Add missing compatible "fsl,vf610-edma" for LS1028A EDMA device, so
that bootloader can fix up the IOMMU entries there. Otherwise, EDMA
just doesn't work on LS1028A with shipped bootloader.
- Fix imx6dl-yapp4-ursa board Ethernet connection.
- Fix input_val for AUDIOMIX_BIT_STREAM pinctrl defines on i.MX8MP
according to Reference Manual.
* tag 'imx-fixes-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: freescale: imx8mp: update input_val for AUDIOMIX_BIT_STREAM
arm64: dts: imx8m: Fix AIPS reg properties
arm64: dts: imx8mn: Change SDMA1 ahb clock for imx8mn
ARM: dts: imx27-phytec-phycard-s-rdk: Fix the I2C1 pinctrl entries
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: imx6dl-yapp4: Fix Ursa board Ethernet connection
arm64: dts: ls1028a: add "fsl,vf610-edma" compatible
dt-bindings: dma: fsl-edma: fix ls1028a-edma compatible
Link: https://lore.kernel.org/r/20200429063226.GT32592@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Recent PTP-specific cpsw driver changes started exposing an issue on at
at least j5eco-evm:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf0169004
...
(davinci_mdio_runtime_suspend) from [<c063f2a4>] (__rpm_callback+0x84/0x154)
(__rpm_callback) from [<c063f394>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c063f4f0>] (rpm_suspend+0xfc/0x6ac)
(rpm_suspend) from [<c0640af0>] (pm_runtime_work+0x88/0xa4)
(pm_runtime_work) from [<c0155338>] (process_one_work+0x228/0x568)
...
Let's fix the issue by using the correct mdio clock as suggested by
Grygorii Strashko <grygorii.strashko@ti.com>.
The DM814_ETHERNET_CPGMAC0_CLKCTRL clock is the interconnect target module
clock and managed by ti-sysc.
Fixes: 6398f3478e45 ("ARM: dts: Configure interconnect target module for dm814x cpsw")
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf345e2e ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Since commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am437x-gp-evm
am437x-sk-evm
am437x-idk-evm
All above boards have phy-mode = "rgmii" and this is worked before, because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the
KSZ9031 PHY") the networking is broken on boards:
am571x-idk
am572x-idk
am574x-idk
am57xx-beagle-x15
All above boards have phy-mode = "rgmii" and this is worked before because
KSZ9031 PHY started with default RGMII internal delays configuration (TX
off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the
KSZ9031 PHY starts handling phy mode properly and disables RX delay, as
result networking is become broken.
Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous
behavior.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Fixes: bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like using the UART CTS pin does not always trigger for a wake-up
when the SoC is idle.
This is probably because the modem first uses gpio_149 to signal the SoC
that data will be sent, and the CTS will only get used later when the
data transfer is starting.
Let's fix the issue by configuring the gpio_149 pad as the wakeirq for
UART. We have gpio_149 managed by the USB PHY for powering up the right
USB mode, and after that, the gpio gets recycled as the modem wake-up
pin. If needeed, the USB PHY can also later on be configured to use
gpio_149 pad as the wakeirq as a shared irq.
Let's also configure the missing properties for uart-has-rtscts and
current-speed for the modem port while at it. We already configure the
hardware flow control pins with uart1_pins pinctrl setting.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wlan on droid4 is flakey on some devices, and experiments have shown this
gets fixed if we disable the internal pull for wlan gpio interrupt line.
The symptoms are that the wlan connection is very slow and almost useless
with lots of wlcore firmware reboot warnings in the dmesg.
In addition to configuring the wlan gpio pulls, let's also configure the rest
of the wlan sd pins. We have not configured those eariler as we're booting
using kexec.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The size field of the tag header structure is supposed to be set to the
size of a tag structure including the header.
Fixes: c772568788b5f0 ("ARM: add additional table to compressed kernel")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Usually it does not hurt to add "clock-names" properties, even if the
(pre-json-schema) DT bindings do not mention them.
However, the actual clock names for the OS Timer nodes are not fixed,
but contain the indices of the consumer instances. Hence they cannot
easily be used by a driver, without scanning for all possible indices.
Remove them, as the OSTM DT bindings do not specify clock-names anyway.
Fixes: bbbcd02b82552907 ("ARM: dts: r7s9210: Initial SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <Chris.Brandt@renesas.com>
Link: https://lore.kernel.org/r/20200427192932.28967-1-geert+renesas@glider.be
A test with the command below gives these errors:
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200424123923.8192-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425192500.1808-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-2-jbx6244@gmail.com
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-1-jbx6244@gmail.com
A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I found
after restarting my randconfig build testing that had been dormant for
a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=K1jH
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I
found after restarting my randconfig build testing that had been
dormant for a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: imx8: select SOC_BUS
soc: tegra: fix tegra_pmc_get_suspend_mode definition
soc: fsl: dpio: avoid stack usage warning
soc: fsl: dpio: fix incorrect pointer conversions
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: bcm283x: Disable dsi0 node
firmware: xilinx: make firmware_debugfs_root static
drivers: soc: xilinx: fix firmware driver Kconfig dependency
ARM: dts: bcm283x: Add cells encoding format to firmware bus
ARM: dts: OMAP3: disable RNG on N950/N9
5.7, please pull the following:
- Nicolas provides a fix for 55c7c0621078 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") which missed adding proper
#address-cells and #size-cells properties and he also disables the DSI
node which should have been disabled by default but was not.
-----BEGIN PGP SIGNATURE-----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=6CKq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Nicolas provides a fix for 55c7c0621078 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") which missed adding proper
#address-cells and #size-cells properties and he also disables the DSI
node which should have been disabled by default but was not.
* tag 'arm-soc/for-5.7/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Disable dsi0 node
ARM: dts: bcm283x: Add cells encoding format to firmware bus
Link: https://lore.kernel.org/r/20200417171725.1084-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The I2C2 pins are already used and the following errors are seen:
imx27-pinctrl 10015000.iomuxc: pin MX27_PAD_I2C2_SDA already requested by 10012000.i2c; cannot claim for 1001d000.i2c
imx27-pinctrl 10015000.iomuxc: pin-69 (1001d000.i2c) status -22
imx27-pinctrl 10015000.iomuxc: could not request pin 69 (MX27_PAD_I2C2_SDA) from group i2c2grp on device 10015000.iomuxc
imx-i2c 1001d000.i2c: Error applying setting, reverse things back
imx-i2c: probe of 1001d000.i2c failed with error -22
Fix it by adding the correct I2C1 IOMUX entries for the pinctrl_i2c1 group.
Cc: <stable@vger.kernel.org>
Fixes: 61664d0b432a ("ARM: dts: imx27 phyCARD-S pinctrl")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Even though commit cfb5d65f2595 ("ARM: dts: dra7: Add bus_dma_limit
for L3 bus") added bus_dma_limit for L3 bus, the PCIe controller
gets incorrect value of bus_dma_limit.
Fix it by adding empty dma-ranges property to axi@0 and axi@1
(parent device tree node of PCIe controller).
Cc: stable@kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit bcbb63b80284 ("ARM: dts: dra7: Separate AM57 dtsi files"),
the m_can node was inherited from dra76x.dtsi but the IP is not
connected on the idk board. Disable the node to reflect this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to tag RNG as disabled for N950/N9 as it blocked by the secure
mode. We have a similar change done for N900, but I missed adding it
for N950/N9 with the recent RNG changes.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAl5+YFQRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXMQDRAAh5iWHOvPNJD5qNOguNrAfFslrSZ0q4gA
IKPJuDh1/5aZEE3oJpBrA5QnDps8hmSZkzYmGJQgHgjk1PXY21tq0Pp8nMz7bt9l
BGQIuUSmr3ZuI+8eciFv7Mg1eDPuyZZqWCQTcsqrketYNA4tql6vPt5SFwDf0L7R
OQz5e/llye70UKD1HaUboM6FPERFRTLXeSNjJUd1uprGQCOR847jpSRjGk9t2nIP
+FrMNPHtF8X4mxVpx8nIoeREG/o6z72K23I0GuVDy6+A00HHsFN8J0EdDTRCad7p
bgb+MFvc25Pepx1qhggsQlKlKMbVIB21pNODCyfRlUSaiNCIbkoBLqkgzlDGaaKM
lll9IJ3+6ZJ1Qy2TgO3ZVIZk8L6O8GPOFsCd8XpqrzHB/M2I4XO50BeZqroOeU/J
hnNtlj+RfoAPZ9rCzYa5wAJLGYhakapFqmVtIJpie3FA1u1TPlebG6GBattT8156
1FpXdHvY8Yovy5vs7fQxQfY4/YGLEt3NPLW/CEoIe2PqRrn+ta5knQrljILk35L6
eW4jaGNeuR69ievRNQgV1mrP4MP+C6RK8qPScpkSH0wPfTE0Rc2d906FwyQtfc3g
6OaikzEjVfSpLFac6vKr0Vl6LGFGaUxJtnrOX6oHcbS14sjEeHmlyPloNX0WFSvh
tYVpEwqtl5k=
=HJcs
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.6/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Boot regression fix for N950/N9
We need to tag RNG as disabled for N950/N9 as it blocked by the secure
mode. We have a similar change done for N900, but I missed adding it
for N950/N9 with the recent RNG changes.
* tag 'omap-for-v5.6/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: OMAP3: disable RNG on N950/N9
Link: https://lore.kernel.org/r/pull-1585340588-558327@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The R-Mobile APE6 Compare Match Timer 1 generates 8 interrupts, one for
each channel, but currently only 1 is described.
Fix this by adding the missing interrupts.
Fixes: f7b65230019b9dac ("ARM: shmobile: r8a73a4: Add CMT1 node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200408090926.25201-1-geert+renesas@glider.be
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
Since its inception the module was meant to be disabled by default, but
the original commit failed to add the relevant property.
Fixes: 4aba4cf82054 ("ARM: dts: bcm2835: Add the DSI module nodes and clocks")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Y Soft yapp4 platform supports up to two Ethernet ports.
The Ursa board though has only one Ethernet port populated and that is
the port@2. Since the introduction of this platform into mainline a wrong
port was deleted and the Ethernet could never work. Fix this by deleting
the correct port node.
Fixes: 87489ec3a77f ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit
0698fac4ac2a ("efi/arm: Clean EFI stub exit code from cache instead of avoiding it")
introduced a PC-relative reference to 'call_cache_fn' into
efi_enter_kernel(), which lives way at the end of head.S. In some cases,
the ARM version of the ADR instruction does not have sufficient range,
resulting in a build error:
arch/arm/boot/compressed/head.S:1453: Error: invalid constant (fffffffffffffbe4) after fixup
ARM defines an alternative with a wider range, called ADRL, but this does
not exist for Thumb-2. At the same time, the ADR instruction in Thumb-2
has a wider range, and so it does not suffer from the same issue.
So let's switch to ADRL for ARM builds, and keep the ADR for Thumb-2 builds.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200409130434.6736-6-ardb@kernel.org
vc4's firmware bus DMA limitations") as it turned out to be faulty
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEErOkkGDHCg2EbPcGjlfZmHno8x/4FAl5+ZSAACgkQlfZmHno8
x/7fWQf/SODT8sooJto4VFAbsDjXjNPmkqXBvFxYcPVN67ET2pSFdiGpGV4/Zt0+
/f1/niWVvOXL8j4MicEjhQeRwRCznzBHb07PW33ynf6i7u+b3eGr/gbfFckbpSsV
FhN5/5rcH7ebnsekGRG3c0386IGtRZW3xE4Dk2wLcRv3qhgs98y+U8s5vGlaxXG6
KAim6SUlh+FZak58CcVovBUe30HpX9vxuuHUk8mzhhrDEbZqDY2VW4VkhcagnAc8
y6X0mriyv6EoJdDzPQtlq94c/siNKIEbrJ/E5ozUU3ZNAs4nu2KIoru0lhXgaNl9
rMnHqEKCCF1/8gXeN1+t2DHXBfVvkA==
=/iN4
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=gRon
-----END PGP SIGNATURE-----
Merge tag 'tags/bcm2835-dt-fixes-2020-03-27' into devicetree/fixes
This patch is to be squashed into 55c7c0621078 ("ARM: dts: bcm283x: Fix
vc4's firmware bus DMA limitations") as it turned out to be faulty
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This is required for wake on lan on i.MX6
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0d5 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl6HpMkACgkQmmx57+YA
GNkGsQ/+KRbE74XGQvZww5PleaesqoZZhrt2gbi0pEJZ/JTgNa3dBkT+JwlToe/H
x7nFVfMZeEl4O9GO0+/CH2tsmQa5BA8R9JddhFxwnZ48ZYLQAdaukwt94LM2zj3K
GFgs47N4DAAF5QJoXNtmmQCXUWbj7A/0S5TTpXe94TYPN9XiJCdsyNNLpW3undTe
K1HLnd4yWGforQc/VfRsV/Gsqi1VNHgL34M3belahiG7x0lytJDCHfhsfmIdxdGR
n3LVRRJr6NhKcuUw3XtA8MxT4dTAcgHjbbDLkS/b1nHfuXMi0/zW8VPBzD/xyHL7
fbFl8ayUMANB6FD/U7ptUC/0IMXuHDUn4B60CEEzK8ddkEbErrmXlYVGogpFHxvm
MqrW8CnO0YEr0YMNAIyZoqHYGq8+8DCq+SRH48brdPzuiKI6OahdV1o07ulGhOjq
ihwoZNE+J0NjeaX7C1xBX3DT1XqdcNPCmu3gx6r06u2FVXVm1J19YkIzQnEXQvKy
NRIw5LIOfEsxkMSQ0oUuAUUUY1Fq1zuHqD8MmgBd3jqIULQqgfahmPL6Dtwm5QFf
R17YsMcQ7ae1Pp7a+D3Jrkbn+s2y8wmJZIqH3eWebps9RvpWmrxzsRfOJ2czhqM1
NY7Z/TGMM7lGM75DZ+xskfk7UCAX+hqMSTiNg9xbRo8946GAbV4=
=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
