IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 29173d07f79883ac94f5570294f98af3d4287382 ]
Sk_buffs are fed into sockmap verdict programs either from a strparser
(when the user might want to decide how framing of skb is done by attaching
another parser program) or directly through tcp_read_sock. The
tcp_read_sock is the preferred method for performance when the BPF logic is
a stream parser.
The flow for Cilium's common use case with a stream parser is,
tcp_read_sock()
sk_psock_verdict_recv
ret = bpf_prog_run_pin_on_cpu()
sk_psock_verdict_apply(sock, skb, ret)
// if system is under memory pressure or app is slow we may
// need to queue skb. Do this queuing through ingress_skb and
// then kick timer to wake up handler
skb_queue_tail(ingress_skb, skb)
schedule_work(work);
The work queue is wired up to sk_psock_backlog(). This will then walk the
ingress_skb skb list that holds our sk_buffs that could not be handled,
but should be OK to run at some later point. However, its possible that
the workqueue doing this work still hits an error when sending the skb.
When this happens the skbuff is requeued on a temporary 'state' struct
kept with the workqueue. This is necessary because its possible to
partially send an skbuff before hitting an error and we need to know how
and where to restart when the workqueue runs next.
Now for the trouble, we don't rekick the workqueue. This can cause a
stall where the skbuff we just cached on the state variable might never
be sent. This happens when its the last packet in a flow and no further
packets come along that would cause the system to kick the workqueue from
that side.
To fix we could do simple schedule_work(), but while under memory pressure
it makes sense to back off some instead of continue to retry repeatedly. So
instead to fix convert schedule_work to schedule_delayed_work and add
backoff logic to reschedule from backlog queue on errors. Its not obvious
though what a good backoff is so use '1'.
To test we observed some flakes whil running NGINX compliance test with
sockmap we attributed these failed test to this bug and subsequent issue.
>From on list discussion. This commit
bec217197b41("skmsg: Schedule psock work if the cached skb exists on the psock")
was intended to address similar race, but had a couple cases it missed.
Most obvious it only accounted for receiving traffic on the local socket
so if redirecting into another socket we could still get an sk_buff stuck
here. Next it missed the case where copied=0 in the recv() handler and
then we wouldn't kick the scheduler. Also its sub-optimal to require
userspace to kick the internal mechanisms of sockmap to wake it up and
copy data to user. It results in an extra syscall and requires the app
to actual handle the EAGAIN correctly.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-3-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 78fa0d61d97a728d306b0c23d353c0e340756437 ]
The read_skb hook calls consume_skb() now, but this means that if the
recv_actor program wants to use the skb it needs to inc the ref cnt
so that the consume_skb() doesn't kfree the sk_buff.
This is problematic because in some error cases under memory pressure
we may need to linearize the sk_buff from sk_psock_skb_ingress_enqueue().
Then we get this,
skb_linearize()
__pskb_pull_tail()
pskb_expand_head()
BUG_ON(skb_shared(skb))
Because we incremented users refcnt from sk_psock_verdict_recv() we
hit the bug on with refcnt > 1 and trip it.
To fix lets simply pass ownership of the sk_buff through the skb_read
call. Then we can drop the consume from read_skb handlers and assume
the verdict recv does any required kfree.
Bug found while testing in our CI which runs in VMs that hit memory
constraints rather regularly. William tested TCP read_skb handlers.
[ 106.536188] ------------[ cut here ]------------
[ 106.536197] kernel BUG at net/core/skbuff.c:1693!
[ 106.536479] invalid opcode: 0000 [#1] PREEMPT SMP PTI
[ 106.536726] CPU: 3 PID: 1495 Comm: curl Not tainted 5.19.0-rc5 #1
[ 106.537023] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ArchLinux 1.16.0-1 04/01/2014
[ 106.537467] RIP: 0010:pskb_expand_head+0x269/0x330
[ 106.538585] RSP: 0018:ffffc90000138b68 EFLAGS: 00010202
[ 106.538839] RAX: 000000000000003f RBX: ffff8881048940e8 RCX: 0000000000000a20
[ 106.539186] RDX: 0000000000000002 RSI: 0000000000000000 RDI: ffff8881048940e8
[ 106.539529] RBP: ffffc90000138be8 R08: 00000000e161fd1a R09: 0000000000000000
[ 106.539877] R10: 0000000000000018 R11: 0000000000000000 R12: ffff8881048940e8
[ 106.540222] R13: 0000000000000003 R14: 0000000000000000 R15: ffff8881048940e8
[ 106.540568] FS: 00007f277dde9f00(0000) GS:ffff88813bd80000(0000) knlGS:0000000000000000
[ 106.540954] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.541227] CR2: 00007f277eeede64 CR3: 000000000ad3e000 CR4: 00000000000006e0
[ 106.541569] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.541915] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.542255] Call Trace:
[ 106.542383] <IRQ>
[ 106.542487] __pskb_pull_tail+0x4b/0x3e0
[ 106.542681] skb_ensure_writable+0x85/0xa0
[ 106.542882] sk_skb_pull_data+0x18/0x20
[ 106.543084] bpf_prog_b517a65a242018b0_bpf_skskb_http_verdict+0x3a9/0x4aa9
[ 106.543536] ? migrate_disable+0x66/0x80
[ 106.543871] sk_psock_verdict_recv+0xe2/0x310
[ 106.544258] ? sk_psock_write_space+0x1f0/0x1f0
[ 106.544561] tcp_read_skb+0x7b/0x120
[ 106.544740] tcp_data_queue+0x904/0xee0
[ 106.544931] tcp_rcv_established+0x212/0x7c0
[ 106.545142] tcp_v4_do_rcv+0x174/0x2a0
[ 106.545326] tcp_v4_rcv+0xe70/0xf60
[ 106.545500] ip_protocol_deliver_rcu+0x48/0x290
[ 106.545744] ip_local_deliver_finish+0xa7/0x150
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()")
Reported-by: William Findlay <will@isovalent.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: William Findlay <will@isovalent.com>
Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/20230523025618.113937-2-john.fastabend@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3002b8642f016d7fe3ff56240dacea1075f6b877 ]
In fact the device with chip id 0xD283 is called NCT6126D, and that is
the chip id the Nuvoton code was written for. Correct that name to avoid
confusion, because a NCT6116D in fact exists as well but has another
chip id, and is currently not supported.
The look at the spec also revealed that GPIO group7 in fact has 8 pins,
so correct the pin count in that group as well.
Fixes: d0918a84aff0 ("gpio-f7188x: Add GPIO support for Nuvoton NCT6116")
Reported-by: Xing Tong Wu <xingtong.wu@siemens.com>
Signed-off-by: Henning Schild <henning.schild@siemens.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c253dfc89efde6b5faddf9e7400e5d17884e042 ]
devcom events are sent to all registered component. Following the
cited patch, it is possible for two components, e.g.: two eswitches,
to send devcom events, while both components are registered. This
means eswitch layer will do double un/pairing, which is double
allocation and free of resources, even though only one un/pairing is
needed. flow example:
cpu0 cpu1
---- ----
mlx5_devlink_eswitch_mode_set(dev0)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw0)
mlx5_devlink_eswitch_mode_set(dev1)
esw_offloads_devcom_init()
mlx5_devcom_register_component(esw1)
mlx5_devcom_send_event()
mlx5_devcom_send_event()
Hence, check whether the eswitches are already un/paired before
free/allocation of resources.
Fixes: 09b278462f16 ("net: devlink: enable parallel ops on netlink interface")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eca9bfafee3a0487e59c59201ae14c7594ba940a ]
When receive buffer is small we try to copy out the data from
TCP into a skb maintained by TLS to prevent connection from
stalling. Unfortunately if a single record is made up of a mix
of decrypted and non-decrypted skbs combining them into a single
skb leads to loss of decryption status, resulting in decryption
errors or data corruption.
Similarly when trying to use TCP receive queue directly we need
to make sure that all the skbs within the record have the same
status. If we don't the mixed status will be detected correctly
but we'll CoW the anchor, again collapsing it into a single paged
skb without decrypted status preserved. So the "fixup" code will
not know which parts of skb to re-encrypt.
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1c607b1e5d5477d82ca6a86a05a4f10907b33ee ]
We'll need to copy input skbs individually in the next patch.
Factor that code out (without assuming we're copying a full record).
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee3a ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 14c4be92ebb3e36e392aa9dd8f314038a9f96f3c ]
If a record is partially decrypted we'll have to CoW it, anyway,
so go into copy mode and allocate a writable skb right away.
This will make subsequent fix simpler because we won't have to
teach tls_strp_msg_make_copy() how to copy skbs while preserving
decrypt status.
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee3a ("tls: rx: strp: preserve decryption status of skbs when needed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b0c0dc9fbbd01e58a573a41c38885f9e4c17696 ]
We call tls_rx_msg_size(skb) before doing skb->len += chunk.
So the tls_rx_msg_size() code will see old skb->len, most
likely leading to an over-read.
Worst case we will over read an entire record, next iteration
will try to trim the skb but may end up turning frag len negative
or discarding the subsequent record (since we already told TCP
we've read it during previous read but now we'll trim it out of
the skb).
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 210620ae44a83f25220450bbfcc22e6fe986b25f ]
alloc_skb_with_frags() fills in page frag sizes but does not
set skb->len and skb->data_len. Set those correctly otherwise
device offload will most likely generate an empty skb and
hit the BUG() at the end of __skb_nsg().
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a03b540e3cf62a255213d084d76d71c02793d5 ]
skb->len covers the entire skb, including the frag_list.
In fact we're guaranteed that rxm->full_len <= skb->len,
so since the change under Fixes we were not checking decrypt
status of any skb but the first.
Note that the skb_pagelen() added here may feel a bit costly,
but it's removed by subsequent fixes, anyway.
Reported-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 86b259f6f888 ("tls: rx: device: bound the frag walk")
Tested-by: Shai Amiram <samiram@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54147fa374dbeadcb01b1762db1a793e06e37de ]
After suspend/resume cycle there is an error message and auto-mode
or CnQF stops working.
[ 5741.447511] amd-pmf AMDI0100:00: SMU cmd failed. err: 0xff
[ 5741.447523] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_RESPONSE:ff
[ 5741.447527] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_ARGUMENT:7
[ 5741.447531] amd-pmf AMDI0100:00: AMD_PMF_REGISTER_MESSAGE:16
[ 5741.447540] amd-pmf AMDI0100:00: [AUTO_MODE] avg power: 0 mW mode: QUIET
This is because the DRAM address used for accessing metrics table
needs to be refreshed after a suspend resume cycle. Add a resume
callback to reset this again.
Fixes: 1a409b35c995 ("platform/x86/amd/pmf: Get performance metrics from PMFW")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20230513011408.958-1-mario.limonciello@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5486b620cd43b16a1787ef92b9bc21bd72ef2e ]
When building sign-file, the call to get the CFLAGS for libcrypto is
missing white-space between `pkg-config` and `--cflags`:
$(shell $(HOSTPKG_CONFIG)--cflags libcrypto 2> /dev/null)
Removing the redirection of stderr, we see:
$ make -C tools/testing/selftests/bpf sign-file
make: Entering directory '[...]/tools/testing/selftests/bpf'
make: pkg-config--cflags: No such file or directory
SIGN-FILE sign-file
make: Leaving directory '[...]/tools/testing/selftests/bpf'
Add the missing space.
Fixes: fc97590668ae ("selftests/bpf: Add test for bpf_verify_pkcs7_signature() kfunc")
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Roberto Sassu <roberto.sassu@huawei.com>
Link: https://lore.kernel.org/bpf/20230426215032.415792-1-jeremy@azazel.net
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6e045361a27ecd4fac6413164e0d091d80eee99 ]
Commit bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
adds support to discovery the UUIDs of the partitions or just fetch the
partition count using the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag.
However the commit doesn't handle the fact that the older version doesn't
understand the flag and must be MBZ which results in firmware returning
invalid parameter error. That results in the failure of the driver probe
which is in correct.
Limit the usage of the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag for the
versions above v1.0(i.e v1.1 and onwards) which fixes the issue.
Fixes: bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
Reported-by: Jens Wiklander <jens.wiklander@linaro.org>
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Tested-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-2-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3632679d9e4f879f49949bb5b050e0de553e4739 ]
With a raw socket bound to IPPROTO_RAW (ie with hdrincl enabled), the
protocol field of the flow structure, build by raw_sendmsg() /
rawv6_sendmsg()), is set to IPPROTO_RAW. This breaks the ipsec policy
lookup when some policies are defined with a protocol in the selector.
For ipv6, the sin6_port field from 'struct sockaddr_in6' could be used to
specify the protocol. Just accept all values for IPPROTO_RAW socket.
For ipv4, the sin_port field of 'struct sockaddr_in' could not be used
without breaking backward compatibility (the value of this field was never
checked). Let's add a new kind of control message, so that the userland
could specify which protocol is used.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
CC: stable@vger.kernel.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20230522120820.1319391-1-nicolas.dichtel@6wind.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91d0b78c5177f3e42a4d8738af8ac19c3a90d002 ]
Users who want to share a single public IP address for outgoing connections
between several hosts traditionally reach for SNAT. However, SNAT requires
state keeping on the node(s) performing the NAT.
A stateless alternative exists, where a single IP address used for egress
can be shared between several hosts by partitioning the available ephemeral
port range. In such a setup:
1. Each host gets assigned a disjoint range of ephemeral ports.
2. Applications open connections from the host-assigned port range.
3. Return traffic gets routed to the host based on both, the destination IP
and the destination port.
An application which wants to open an outgoing connection (connect) from a
given port range today can choose between two solutions:
1. Manually pick the source port by bind()'ing to it before connect()'ing
the socket.
This approach has a couple of downsides:
a) Search for a free port has to be implemented in the user-space. If
the chosen 4-tuple happens to be busy, the application needs to retry
from a different local port number.
Detecting if 4-tuple is busy can be either easy (TCP) or hard
(UDP). In TCP case, the application simply has to check if connect()
returned an error (EADDRNOTAVAIL). That is assuming that the local
port sharing was enabled (REUSEADDR) by all the sockets.
# Assume desired local port range is 60_000-60_511
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
s.bind(("192.0.2.1", 60_000))
s.connect(("1.1.1.1", 53))
# Fails only if 192.0.2.1:60000 -> 1.1.1.1:53 is busy
# Application must retry with another local port
In case of UDP, the network stack allows binding more than one socket
to the same 4-tuple, when local port sharing is enabled
(REUSEADDR). Hence detecting the conflict is much harder and involves
querying sock_diag and toggling the REUSEADDR flag [1].
b) For TCP, bind()-ing to a port within the ephemeral port range means
that no connecting sockets, that is those which leave it to the
network stack to find a free local port at connect() time, can use
the this port.
IOW, the bind hash bucket tb->fastreuse will be 0 or 1, and the port
will be skipped during the free port search at connect() time.
2. Isolate the app in a dedicated netns and use the use the per-netns
ip_local_port_range sysctl to adjust the ephemeral port range bounds.
The per-netns setting affects all sockets, so this approach can be used
only if:
- there is just one egress IP address, or
- the desired egress port range is the same for all egress IP addresses
used by the application.
For TCP, this approach avoids the downsides of (1). Free port search and
4-tuple conflict detection is done by the network stack:
system("sysctl -w net.ipv4.ip_local_port_range='60000 60511'")
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_IP, IP_BIND_ADDRESS_NO_PORT, 1)
s.bind(("192.0.2.1", 0))
s.connect(("1.1.1.1", 53))
# Fails if all 4-tuples 192.0.2.1:60000-60511 -> 1.1.1.1:53 are busy
For UDP this approach has limited applicability. Setting the
IP_BIND_ADDRESS_NO_PORT socket option does not result in local source
port being shared with other connected UDP sockets.
Hence relying on the network stack to find a free source port, limits the
number of outgoing UDP flows from a single IP address down to the number
of available ephemeral ports.
To put it another way, partitioning the ephemeral port range between hosts
using the existing Linux networking API is cumbersome.
To address this use case, add a new socket option at the SOL_IP level,
named IP_LOCAL_PORT_RANGE. The new option can be used to clamp down the
ephemeral port range for each socket individually.
The option can be used only to narrow down the per-netns local port
range. If the per-socket range lies outside of the per-netns range, the
latter takes precedence.
UAPI-wise, the low and high range bounds are passed to the kernel as a pair
of u16 values in host byte order packed into a u32. This avoids pointer
passing.
PORT_LO = 40_000
PORT_HI = 40_511
s = socket(AF_INET, SOCK_STREAM)
v = struct.pack("I", PORT_HI << 16 | PORT_LO)
s.setsockopt(SOL_IP, IP_LOCAL_PORT_RANGE, v)
s.bind(("127.0.0.1", 0))
s.getsockname()
# Local address between ("127.0.0.1", 40_000) and ("127.0.0.1", 40_511),
# if there is a free port. EADDRINUSE otherwise.
[1] https://github.com/cloudflare/cloudflare-blog/blob/232b432c1d57/2022-02-connectx/connectx.py#L116
Reviewed-by: Marek Majkowski <marek@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 3632679d9e4f ("ipv{4,6}/raw: fix output xfrm lookup wrt protocol")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 57fb54ab9f6945e204740b696bd4cee61ee04e5e upstream.
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 640bf95b2c7c2981fb471acdafbd3e0458f8390d upstream.
Should tc589_config() fail, some resources need to be released as already
done in the remove function.
Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/d8593ae867b24c79063646e36f9b18b0790107cb.1684575975.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35112271672ae98f45df7875244a4e33aa215e31 upstream.
We found a crash when using SMCRv2 with 2 Mellanox ConnectX-4. It
can be reproduced by:
- smc_run nginx
- smc_run wrk -t 32 -c 500 -d 30 http://<ip>:<port>
BUG: kernel NULL pointer dereference, address: 0000000000000014
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 8000000108713067 P4D 8000000108713067 PUD 151127067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 4 PID: 2441 Comm: kworker/4:249 Kdump: loaded Tainted: G W E 6.4.0-rc1+ #42
Workqueue: smc_hs_wq smc_listen_work [smc]
RIP: 0010:smc_clc_send_confirm_accept+0x284/0x580 [smc]
RSP: 0018:ffffb8294b2d7c78 EFLAGS: 00010a06
RAX: ffff8f1873238880 RBX: ffffb8294b2d7dc8 RCX: 0000000000000000
RDX: 00000000000000b4 RSI: 0000000000000001 RDI: 0000000000b40c00
RBP: ffffb8294b2d7db8 R08: ffff8f1815c5860c R09: 0000000000000000
R10: 0000000000000400 R11: 0000000000000000 R12: ffff8f1846f56180
R13: ffff8f1815c5860c R14: 0000000000000001 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff8f1aefd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000014 CR3: 00000001027a0001 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? mlx5_ib_map_mr_sg+0xa1/0xd0 [mlx5_ib]
? smcr_buf_map_link+0x24b/0x290 [smc]
? __smc_buf_create+0x4ee/0x9b0 [smc]
smc_clc_send_accept+0x4c/0xb0 [smc]
smc_listen_work+0x346/0x650 [smc]
? __schedule+0x279/0x820
process_one_work+0x1e5/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x2c/0x50
</TASK>
During the CLC handshake, server sequentially tries available SMCRv2
and SMCRv1 devices in smc_listen_work().
If an SMCRv2 device is found. SMCv2 based link group and link will be
assigned to the connection. Then assumed that some buffer assignment
errors happen later in the CLC handshake, such as RMB registration
failure, server will give up SMCRv2 and try SMCRv1 device instead. But
the resources assigned to the connection won't be reset.
When server tries SMCRv1 device, the connection creation process will
be executed again. Since conn->lnk has been assigned when trying SMCRv2,
it will not be set to the correct SMCRv1 link in
smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to
correct SMCRv1 link group but conn->lnk points to the SMCRv2 link
mistakenly.
Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx]
will be accessed. Since the link->link_idx is not correct, the related
MR may not have been initialized, so crash happens.
| Try SMCRv2 device first
| |-> conn->lgr: assign existed SMCRv2 link group;
| |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC);
| |-> sndbuf & RMB creation fails, quit;
|
| Try SMCRv1 device then
| |-> conn->lgr: create SMCRv1 link group and assign;
| |-> conn->link: keep SMCRv2 link mistakenly;
| |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0]
| initialized.
|
| Then smc_clc_send_confirm_accept() accesses
| conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash.
v
This patch tries to fix this by cleaning conn->lnk before assigning
link. In addition, it is better to reset the connection and clean the
resources assigned if trying SMCRv2 failed in buffer creation or
registration.
Fixes: e49300a6bf62 ("net/smc: add listen processing for SMC-Rv2")
Link: https://lore.kernel.org/r/20220523055056.2078994-1-liuyacan@corp.netease.com/
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a511637502b1caa135046d0f8fdabd55a31af8ef upstream.
Add hardware version read check for PMIC MT6359
Signed-off-by: Sen Chu <sen.chu@mediatek.com
Fixes: 4cfc96547512 ("regulator: mt6359: Add support for MT6359P regulator")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com
Link: https://lore.kernel.org/r/20230518040646.8730-1-sen.chu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 111a833dc5cbef3d05b2a796a7e23cb7f6ff2192 upstream.
The transmit buffers allocated by the driver can be used to transmit data
by any messages/commands needing the buffer. However, it is not guaranteed
to have been zero-ed before every new transmission and hence it will just
contain residual value from the previous transmission. There are several
reserved fields in the memory descriptors that must be zero(MBZ). The
receiver can reject the transmission if any such MBZ fields are non-zero.
While we can set the whole page to zero, it is not optimal as most of the
fields get initialised to the value required for the current transmission.
So, just set the reserved/MBZ fields to zero in the memory descriptors
explicitly to honour the requirement and keep the receiver happy.
Fixes: cc2195fe536c ("firmware: arm_ffa: Add support for MEM_* interfaces")
Reported-by: Marc Bonnici <marc.bonnici@arm.com>
Link: https://lore.kernel.org/r/20230503131252.12585-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f161cea5a20f3aeeb637a88ad1705fc2720b4d58 upstream.
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: ade0176dd8a0 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f893f57a3bf9fe1f4bcb25b55aea7f7f9712fe7 upstream.
From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
Fixes: fadd59fc50d0 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af87194352cad882d787d06fb7efa714acd95427 upstream.
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
Fixes: fadd59fc50d0 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a0a935fb64ee8af253b9c6133bb6702fb152ac2 upstream.
DEVX can issue a general command, which is not used by mlx5 driver.
In case such command is failed, mlx5 is trying to collect the failure
data, However, mlx5 doesn't create a storage for this command, since
mlx5 doesn't use it. This lead to array-index-out-of-bounds error.
Fix it by checking whether the command is known before collecting the
failure data.
Fixes: 34f46ae0d4b3 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c7dd225bc224726c22db08e680bf787f60ebdee3 upstream.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
Fixes: 7304d603a57a ("net/mlx5: DR, Add support for force-loopback QP")
Signed-off-by: Itamar Gozlan <igozlan@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be5bd42a5bba1a05daedc86cf0e248210009669 upstream.
In case user switch a device from switchdev mode to legacy mode, mlx5
first unpair the E-switch and afterwards unload the uplink vport.
From the other hand, in case user remove or reload a device, mlx5
first unload the uplink vport and afterwards unpair the E-switch.
The latter is causing a bug[1], hence, handle pairing of E-switch as
part of uplink un/load APIs.
[1]
In case VF_LAG is used, every tc fdb flow is duplicated to the peer
esw. However, the original esw keeps a pointer to this duplicated
flow, not the peer esw.
e.g.: if user create tc fdb flow over esw0, the flow is duplicated
over esw1, in FW/HW, but in SW, esw0 keeps a pointer to the duplicated
flow.
During module unload while a peer tc fdb flow is still offloaded, in
case the first device to be removed is the peer device (esw1 in the
example above), the peer net-dev is destroyed, and so the mlx5e_priv
is memset to 0.
Afterwards, the peer device is trying to unpair himself from the
original device (esw0 in the example above). Unpair API invoke the
original device to clear peer flow from its eswitch (esw0), but the
peer flow, which is stored over the original eswitch (esw0), is
trying to use the peer mlx5e_priv, which is memset to 0 and result in
bellow kernel-oops.
[ 157.964081 ] BUG: unable to handle page fault for address: 000000000002ce60
[ 157.964662 ] #PF: supervisor read access in kernel mode
[ 157.965123 ] #PF: error_code(0x0000) - not-present page
[ 157.965582 ] PGD 0 P4D 0
[ 157.965866 ] Oops: 0000 [#1] SMP
[ 157.967670 ] RIP: 0010:mlx5e_tc_del_fdb_flow+0x48/0x460 [mlx5_core]
[ 157.976164 ] Call Trace:
[ 157.976437 ] <TASK>
[ 157.976690 ] __mlx5e_tc_del_fdb_peer_flow+0xe6/0x100 [mlx5_core]
[ 157.977230 ] mlx5e_tc_clean_fdb_peer_flows+0x67/0x90 [mlx5_core]
[ 157.977767 ] mlx5_esw_offloads_unpair+0x2d/0x1e0 [mlx5_core]
[ 157.984653 ] mlx5_esw_offloads_devcom_event+0xbf/0x130 [mlx5_core]
[ 157.985212 ] mlx5_devcom_send_event+0xa3/0xb0 [mlx5_core]
[ 157.985714 ] esw_offloads_disable+0x5a/0x110 [mlx5_core]
[ 157.986209 ] mlx5_eswitch_disable_locked+0x152/0x170 [mlx5_core]
[ 157.986757 ] mlx5_eswitch_disable+0x51/0x80 [mlx5_core]
[ 157.987248 ] mlx5_unload+0x2a/0xb0 [mlx5_core]
[ 157.987678 ] mlx5_uninit_one+0x5f/0xd0 [mlx5_core]
[ 157.988127 ] remove_one+0x64/0xe0 [mlx5_core]
[ 157.988549 ] pci_device_remove+0x31/0xa0
[ 157.988933 ] device_release_driver_internal+0x18f/0x1f0
[ 157.989402 ] driver_detach+0x3f/0x80
[ 157.989754 ] bus_remove_driver+0x70/0xf0
[ 157.990129 ] pci_unregister_driver+0x34/0x90
[ 157.990537 ] mlx5_cleanup+0xc/0x1c [mlx5_core]
[ 157.990972 ] __x64_sys_delete_module+0x15a/0x250
[ 157.991398 ] ? exit_to_user_mode_prepare+0xea/0x110
[ 157.991840 ] do_syscall_64+0x3d/0x90
[ 157.992198 ] entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 04de7dda7394 ("net/mlx5e: Infrastructure for duplicated offloading of TC flows")
Fixes: 1418ddd96afd ("net/mlx5e: Duplicate offloaded TC eswitch rules under uplink LAG")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e5daf5565b61a96e570865091589afc9156e3d3 upstream.
When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.
The solution is to switch the bytes from the crc result for all types
of arc.
Fixes: 40416d8ede65 ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib")
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afbed3f74830163f9559579dee382cac3cff82da upstream.
NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.
Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.
In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.
The immediate stack trace I was seeing is:
__do_softirq+0xd1/0x2c0
__local_bh_enable_ip+0xc7/0x120
</IRQ>
<TASK>
page_pool_put_defragged_page+0x267/0x320
mlx5e_free_xdpsq_desc+0x99/0xd0
mlx5e_poll_xdpsq_cq+0x138/0x3b0
mlx5e_napi_poll+0xc3/0x8b0
netpoll_poll_dev+0xce/0x150
AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Fixes: 60bbf7eeef10 ("mlx5: use page_pool for xdp_return_frame call")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be071cdb167fc3e25fe81922166b3d499d23e8ac upstream.
With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.
[0]:
Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel: <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel: mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel: ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? __kthread_parkme+0xd9/0x1d0
Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7aa50380191635e5897a773f272829cc961a2be5 upstream.
Check in the mlx5e_ptp_poll_ts_cq context if the ptp tx sq should be woken
up. Before change, the ptp tx sq may never wake up if the ptp tx ts skb
fifo is full when mlx5e_poll_tx_cq checks if the queue should be woken up.
Fixes: 1880bc4e4a96 ("net/mlx5e: Add TX port timestamp support")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95e4b25192e9238fd2dbe85d96dd2f8fd1ce9d14 upstream.
The sscanf() function never returns negatives. It returns the number of
items successfully read.
Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/4ccdfd28-099b-40bf-8d77-ad4ea2e76b93@kili.mountain
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b17a4971d3b2a073f4078dd65331efbe35baa2d upstream.
If an error occures after calling nv_mgmt_acquire_sema(), it should be
undone with a corresponding nv_mgmt_release_sema() call.
Add it in the error handling path of the probe as already done in the
remove function.
Fixes: cac1c52c3621 ("forcedeth: mgmt unit interface")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Link: https://lore.kernel.org/r/355e9a7d351b32ad897251b6f81b5886fcdc6766.1684571393.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ca328e985cd995dfd1d5de44046e6074f853fbb upstream.
When doing plpmtu probe, the probe size is growing every time when it
receives the ACK during the Search state until the probe fails. When
the failure occurs, pl.probe_high is set and it goes to the Complete
state.
However, if the link pmtu is huge, like 65535 in loopback_dev, the probe
eventually keeps using SCTP_MAX_PLPMTU as the probe size and never fails.
Because of that, pl.probe_high can not be set, and the plpmtu probe can
never go to the Complete state.
Fix it by setting pl.probe_high to SCTP_MAX_PLPMTU when the probe size
grows to SCTP_MAX_PLPMTU in sctp_transport_pl_recv(). Also, not allow
the probe size greater than SCTP_MAX_PLPMTU in the Complete state.
Fixes: b87641aff9e7 ("sctp: do state transition when a probe succeeds on HB ACK recv path")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce17ad0d54985e2595a3e615fda31df61808a08c upstream.
The Memory_Info_Valid bit (CXL 3.0 8.1.3.8.2) indicates that the CXL
Range Size High and Size Low registers are valid. The bit must be set
within 1 second of reset deassertion to the device. Check valid bit
before we check the Memory_Active bit when waiting for
cxl_await_media_ready() to ensure that the memory info is valid for
consumption. Also ensures both DVSEC ranges 1 and 2 are ready if DVSEC
Capability indicates they are both supported.
Fixes: 523e594d9cc0 ("cxl/pci: Implement wait for media active")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/168444687469.3134781.11033518965387297327.stgit@djiang5-mobl3
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d849996f7458042af803b7d15a181922834c5249 upstream.
Path and its components should be accessed under lock to prevent
problems with one thread modifying them while other tries to read.
Fixes: c8c960c10971 ("ASoC: Intel: avs: APL-based platforms support")
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95109657471311601b98e71f03d0244f48dc61bb upstream.
Constant 'C4_CHANNEL' does not exist on the firmware side. Value 0xC is
reserved for 'C7_1' instead.
Fixes: 04afbbbb1cba ("ASoC: Intel: Skylake: Update the topology interface structure")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230519201711.4073845-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e4be0d011f21593c6b316806779ba1eba2cd7e0 upstream.
The commit e335bb51cc15 ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
#include <linux/module.h>
static int init(void)
{
asm volatile("sub $0x4,%rsp");
dump_stack();
asm volatile("add $0x4,%rsp");
return -EAGAIN;
}
module_init(init);
MODULE_LICENSE("GPL");
crashes the kernel.
Fixes: e335bb51cc15 ("x86/unwind: Ensure stack pointer is aligned")
Signed-off-by: Vernon Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lore.kernel.org/r/20230512104232.GA10227@redhat.com
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fafac202d18230bb9926bda48e563fd2cce2a4f upstream.
In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock". The bug is that the caller also frees sock.
Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.
Fixes: 5db4d286a8ef ("xen/pvcalls: implement connect command")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/e5f98dc2-0305-491f-a860-71bbd1398a2f@kili.mountain
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 335b4223466dd75f9f3ea4918187afbadd22e5c8 upstream.
Commit bf5e758f02fc ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.
Commit 6c796996ee70 ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.
Fix this by making use of the fallback functions for sysfs population.
Fixes: bf5e758f02fc ("genirq/msi: Simplify sysfs handling")
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230503131656.15928-1-mheyne@amazon.de
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91aa4b3782448a7a13baa8cbcdfd5fd19defcbd9 upstream.
This worked before by coincidence, as the regulator was probed and enabled
before PCI RC probe. But probe order changed since commit 259b93b21a9f
("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in
4.14") and PCIe supply is enabled after RC.
Fix this by adding the regulator to RC node.
The PCIe vaux regulator still needs to be enabled unconditionally for
Mini-PCIe USB-only devices.
Fixes: ef3846247b41 ("ARM: dts: imx6qdl: add TQ-Systems MBa6x device trees")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f67bc15e526bb9920683ad6c1891ff9e08981335 upstream.
This code generates a Smatch warning:
drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
error: uninitialized symbol 'bufp'.
The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE. Fix this bug by adding an explicit
check for error codes.
Fixes: 75f4e3619fe2 ("coresight: tmc-etr: Add transparent buffer management")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/7d33e244-d8b9-4c27-9653-883a13534b01@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbb320bfe2c3e9740fe89cfa0a7089b4e8bfc4ff upstream.
Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot(). Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.
On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.
Fixes: aa2ddd242572 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping")
Signed-off-by: Steve Wahl <steve.wahl@hpe.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f15afbd34d8fadbd375f1212e97837e32bc170cc upstream.
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: e462ec50cb5f ("VFS: Differentiate mount flags (MS_*) from internal superblock flags")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags]
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19b8766459c41c6f318f8a548cc1c66dffd18363 upstream.
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488b9 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration")
Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com>
Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
