IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 483ae90d8f976f8339cf81066312e1329f2d3706 upstream.
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Reported-by: Orel Hagag <orelh@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/2d91c89afba59c22587b444994ae419dbea8d876.1705502064.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3df95e265924ac898c1a38a0c01846dd0bd3b354 ]
Variable firmware_stat is possible to be used without initialization.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 1c5d463c0770 ("wifi: mwifiex: add extra delay for firmware ready")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202312192236.ZflaWYCw-lkp@intel.com/
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231221015511.1032128-1-yu-hao.lin@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c5d463c0770c6fa2037511a24fb17966fd07d97 ]
For SDIO IW416, due to a bug, FW may return ready before complete full
initialization. Command timeout may occur at driver load after reboot.
Workaround by adding 100ms delay at checking FW status.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin AM62 (IW416)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231208234029.2197-1-yu-hao.lin@nxp.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bba047f15851c8b053221f1b276eb7682d59f755 ]
The Marvell SD8978 (aka NXP IW416) uses identical registers as SD8987,
so reuse the existing mwifiex_reg_sd8987 definition.
Note that mwifiex_reg_sd8977 and mwifiex_reg_sd8997 are likewise
identical, save for the fw_dump_ctrl register: They define it as 0xf0
whereas mwifiex_reg_sd8987 defines it as 0xf9. I've verified that
0xf9 is the correct value on SD8978. NXP's out-of-tree driver uses
0xf9 for all of them, so there's a chance that 0xf0 is not correct
in the mwifiex_reg_sd8977 and mwifiex_reg_sd8997 definitions. I cannot
test that for lack of hardware, hence am leaving it as is.
NXP has only released a firmware which runs Bluetooth over UART.
Perhaps Bluetooth over SDIO is unsupported by this chipset.
Consequently, only an "sdiouart" firmware image is referenced, not an
alternative "sdsd" image.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/536b4f17a72ca460ad1b07045757043fb0778988.1674827105.git.lukas@wunner.de
Stable-dep-of: 1c5d463c0770 ("wifi: mwifiex: add extra delay for firmware ready")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2aa0a5e65eae27dbd96faca92c84ecbf6f492d42 upstream.
The TDCO calculation was done using the currently applied data bittiming,
instead of the newly computed data bittiming, which means that the TDCO
had an invalid value unless setting the same data bittiming twice.
Fixes: d99755f71a80 ("can: netlink: add interface for CAN-FD Transmitter Delay Compensation (TDC)")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/40579c18-63c0-43a4-8d4c-f3a6c1c0b417@munic.io
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9cae43da9867412f8bd09aee5c8a8dc5e8dc3dc2 upstream.
If hv_netvsc driver is unloaded and reloaded, the NET_DEVICE_REGISTER
handler cannot perform VF register successfully as the register call
is received before netvsc_probe is finished. This is because we
register register_netdevice_notifier() very early( even before
vmbus_driver_register()).
To fix this, we try to register each such matching VF( if it is visible
as a netdevice) at the end of netvsc_probe.
Cc: stable@vger.kernel.org
Fixes: 85520856466e ("hv_netvsc: Fix race of register_netdevice_notifier and VF register")
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9def04e759caa5a3d741891037ae99f81e2fff01 upstream.
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw_new resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bc4ce46b1e3d1da4309405cd4afc7c0fcddd0b90 upstream.
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a1c13303ff6d64e6f718dc8aa614e580ca8d9b4 upstream.
When physical ports are reset (either through link failure or manually
toggled down and up again) that are slaved to a Linux bond with a tunnel
endpoint IP address on the bond device, not all tunnel packets arriving
on the bond port are decapped as expected.
The bond dev assigns the same MAC address to itself and each of its
slaves. When toggling a slave device, the same MAC address is therefore
offloaded to the NFP multiple times with different indexes.
The issue only occurs when re-adding the shared mac. The
nfp_tunnel_add_shared_mac() function has a conditional check early on
that checks if a mac entry already exists and if that mac entry is
global: (entry && nfp_tunnel_is_mac_idx_global(entry->index)). In the
case of a bonded device (For example br-ex), the mac index is obtained,
and no new index is assigned.
We therefore modify the conditional in nfp_tunnel_add_shared_mac() to
check if the port belongs to the LAG along with the existing checks to
prevent a new global mac index from being re-assigned to the slave port.
Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs")
CC: stable@vger.kernel.org # 5.1+
Signed-off-by: Daniel de Villiers <daniel.devilliers@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3d4f7f2288901ed2392695919b3c0e24c1b4084 upstream.
The 1st and 2nd expansion BAR configuration registers are configured,
when the driver starts up, in variables 'barcfg_msix_general' and
'barcfg_msix_xpb', respectively. The 'LengthSelect' field is ORed in
from bit 0, which is incorrect. The 'LengthSelect' field should
start from bit 27.
This has largely gone un-noticed because
NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT happens to be 0.
Fixes: 4cb584e0ee7d ("nfp: add CPP access core")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Daniel Basilio <daniel.basilio@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a007b8009b5f8af021021b7a590a6da0dc4c6e0 upstream.
The nfp driver will merge the tp source port and tp destination port
into one dword which the offset must be zero to do hardware offload.
However, the mangle action for the tp source port and tp destination
port is separated for tc ct action. Modify the mangle action for the
FLOW_ACT_MANGLE_HDR_TYPE_TCP and FLOW_ACT_MANGLE_HDR_TYPE_UDP to
satisfy the nfp driver offload check for the tp port.
The mangle action provides a 4B value for source, and a 4B value for
the destination, but only 2B of each contains the useful information.
For offload the 2B of each is combined into a single 4B word. Since the
incoming mask for the source is '0xFFFF<mask>' the shift-left will
throw away the 0xFFFF part. When this gets combined together in the
offload it will clear the destination field. Fix this by setting the
lower bits back to 0xFFFF, effectively doing a rotate-left operation on
the mask.
Fixes: 5cee92c6f57a ("nfp: flower: support hw offload for ct nat action")
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Hui Zhou <hui.zhou@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20240124151909.31603-3-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0526ec5360a48ad3ab2e26e802b0532302a7e11 upstream.
In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the
VMBus channel"), napi_disable was getting called for all channels,
including all subchannels without confirming if they are enabled or not.
This caused hv_netvsc getting hung at napi_disable, when netvsc_probe()
has finished running but nvdev->subchan_work has not started yet.
netvsc_subchan_work() -> rndis_set_subchannel() has not created the
sub-channels and because of that netvsc_sc_open() is not running.
netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which
netvsc_subchan_work did not run.
netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI
cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the
NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the
opposite.
Now during netvsc_device_remove(), when napi_disable is called for those
subchannels, napi_disable gets stuck on infinite msleep.
This fix addresses this problem by ensuring that napi_disable() is not
getting called for non-enabled NAPI struct.
But netif_napi_del() is still necessary for these non-enabled NAPI struct
for cleanup purpose.
Call trace:
[ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002
[ 654.568030] Call Trace:
[ 654.571221] <TASK>
[ 654.573790] __schedule+0x2d6/0x960
[ 654.577733] schedule+0x69/0xf0
[ 654.581214] schedule_timeout+0x87/0x140
[ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20
[ 654.590291] msleep+0x2d/0x40
[ 654.593625] napi_disable+0x2b/0x80
[ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc]
[ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc]
[ 654.611101] ? do_wait_intr+0xb0/0xb0
[ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc]
[ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus]
Cc: stable@vger.kernel.org
Fixes: ac5047671758 ("hv_netvsc: Disable NAPI before closing the VMBus channel")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1706686551-28510-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b55984c96ffe9e236eb9c82a2196e0b1f84990d upstream.
Invoking the make_tx_response() / push_tx_responses() pair with no lock
held would be acceptable only if all such invocations happened from the
same context (NAPI instance or dealloc thread). Since this isn't the
case, and since the interface "spec" also doesn't demand that multicast
operations may only be performed with no in-flight transmits,
MCAST_{ADD,DEL} processing also needs to acquire the response lock
around the invocations.
To prevent similar mistakes going forward, "downgrade" the present
functions to private helpers of just the two remaining ones using them
directly, with no forward declarations anymore. This involves renaming
what so far was make_tx_response(), for the new function of that name
to serve the new (wrapper) purpose.
While there,
- constify the txp parameters,
- correct xenvif_idx_release()'s status parameter's type,
- rename {,_}make_tx_response()'s status parameters for consistency with
xenvif_idx_release()'s.
Fixes: 210c34dcd8d9 ("xen-netback: add support for multicast control")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Link: https://lore.kernel.org/r/980c6c3d-e10e-4459-8565-e8fbde122f00@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4896bb7c0b31a0a3379b290ea7729900c59e0c69 upstream.
With the dma conf being reallocated on each call to stmmac_open(), any
information in there is lost, unless we specifically handle it.
The STMMAC_TBS_EN bit is set when adding an etf qdisc, and the etf qdisc
therefore would stop working when link was set down and then back up.
Fixes: ba39b344e924 ("net: ethernet: stmicro: stmmac: generate stmmac dma conf before open")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c73729b64bb692186da080602cd13612783f52ac ]
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39fac ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73d9629e1c8c1982f13688c4d1019c3994647ccc ]
Currently when PF administratively sets VF's MAC address and the VF
is put down (VF tries to delete all MACs) then the MAC is removed
from MAC filters and primary VF MAC is zeroed.
Do not allow untrusted VF to remove primary MAC when it was set
administratively by PF.
Reproducer:
1) Create VF
2) Set VF interface up
3) Administratively set the VF's MAC
4) Put VF interface down
[root@host ~]# echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
[root@host ~]# ip link set enp2s0f0v0 up
[root@host ~]# ip link set enp2s0f0 vf 0 mac fe:6c:b5:da:c7:7d
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether fe:6c:b5:da:c7:7d brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
[root@host ~]# ip link set enp2s0f0v0 down
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
Fixes: 700bbf6c1f9e ("i40e: allow VF to remove any MAC filter")
Fixes: ceb29474bbbc ("i40e: Add support for VF to specify its primary MAC address")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240208180335.1844996-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15faa1f67ab405d47789d4702f587ec7df7ef03e ]
There is a crash when adding one of the lan966x interfaces under a lag
interface. The issue can be reproduced like this:
ip link add name bond0 type bond miimon 100 mode balance-xor
ip link set dev eth0 master bond0
The reason is because when adding a interface under the lag it would go
through all the ports and try to figure out which other ports are under
that lag interface. And the issue is that lan966x can have ports that are
NULL pointer as they are not probed. So then iterating over these ports
it would just crash as they are NULL pointers.
The fix consists in actually checking for NULL pointers before accessing
something from the ports. Like we do in other places.
Fixes: cabc9d49333d ("net: lan966x: Add lag support for lan966x")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206123054.3052966-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65c6ee90455053cfd3067c17aaa4a42b0c766543 ]
This is an error path and Smatch complains that "tbl_rev" is uninitialized
on this path. All the other functions follow this same patter where they
set the error code and goto out_free so that's probably what was intended
here as well.
Fixes: e8e10a37c51c ("iwlwifi: acpi: move ppag code from mvm to fw/acpi")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/09900c01-6540-4a32-9451-563da0029cb6@moroto.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ebb5b67641994de8bc486b33457fe0b681d6fe ]
This saves the error as PTR_ERR(wifi_pkg). The problem is that
"wifi_pkg" is a valid pointer, not an error pointer. Set the error code
to -EINVAL instead.
Fixes: 2a8084147bff ("iwlwifi: acpi: support reading and storing WRDS revision 1 and 2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/9620bb77-2d7c-4d76-b255-ad824ebf8e35@moroto.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1ce2654d87e2fb91fea83b288bd9b2641045e42a upstream.
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1692b9775e745f84b69dc8ad0075b0855a43db4e upstream.
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b09b58e31b0f43d76f79b9943da3fb7c2843dcbb ]
When qmem_alloc and pfvf->hw_ops->sq_aq_init fails, sq->sg should be
freed to prevent memleak.
Fixes: c9c12d339d93 ("octeontx2-pf: Add support for PTP clock")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46eba193d04f8bd717e525eb4110f3c46c12aec3 ]
Commit 56e58d6c8a56 ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a56 ("net: stmmac: Implement Safety Features in XGMAC core")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 486058f42a4728053ae69ebbf78e9731d8ce6f8b upstream.
As suggested by Paolo in link[1], if the memory allocation fails, the mm
layer will emit a lot warning comprising the backtrace, so remove the
print.
[1] https://lore.kernel.org/all/20231118081653.1481260-1-shaozhengchao@huawei.com/
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From: Bailey Forrest <bcf@google.com>
Call skb_shinfo() after gve_prep_tso() on DQO TX path.
gve_prep_tso() calls skb_cow_head(), which may reallocate
shinfo causing a use after free.
This bug was unintentionally fixed by 'a6fb8d5a8b69
("gve: Tx path for DQO-QPL")' while adding DQO-QPL format
support in 6.6. That patch is not appropriate for stable releases.
Fixes: a57e5de476be ("gve: DQO: Add TX path")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Bailey Forrest <bcf@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jeroen de Borst <jeroendb@google.com>
Reviewed-by: Kevin DeCabooter <decabooter@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c44fc98f0a8ffd94fa0bd291928e7e312ffc7ca4 ]
When working with GPIO, its direction must be set either when the GPIO is
requested by gpiod_get*() or later on by one of the gpiod_direction_*()
functions. Neither of this is done here which results in undefined
behavior on some systems.
As the reset GPIO is used right after it is requested here, it makes sense
to configure it as GPIOD_OUT_HIGH right away. With that, the following
gpiod_set_value_cansleep(1) becomes redundant and can be safely
removed.
Fixes: a653f2f538f9 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1706266175-3408-1-git-send-email-michal.vokac@ysoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc404d20d1b46d89b461918bc44587620eda200 ]
All error handling paths, except this one, go to 'out' where
release_swfw_sync() is called.
This call balances the acquire_swfw_sync() call done at the beginning of
the function.
Branch to the error handling path in order to correctly release some
resources in case of error.
Fixes: ae14a1d8e104 ("ixgbe: Fix IOSF SB access issues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c1b4af8c1b20c70dde01e58381685d6a4a1d2c8 ]
Currently ixgbe driver is notified of overheating events
via internal IXGBE_ERR_OVERTEMP error code.
Change the approach for handle_lasi() to use freshly introduced
is_overtemp function parameter which set when such event occurs.
Change check_overtemp() to bool and return true if overtemp
event occurs.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5795f533f30a80aa0473652876296ebc9129e33a ]
Change returning codes to the kernel ones instead of
the internal ones for the entire ixgbe driver.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: bbc404d20d1b ("ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b4248105353e7d1debd30ca5c57ec5e5f28e35 ]
In case the interface between the MAC and the PHY is SGMII, then the bit
GIGA_MODE on the MAC side needs to be set regardless of the speed at
which it is running.
Fixes: d28d6d2e37d1 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3fe8d28c67bf6c291e920c6d04fa22afa14e6e4 ]
Fix the warnings when building virtio_net driver.
"
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4551:48: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Wformat-overflow=]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4551:41: note: directive argument in the range [-2147483643, 65534]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~
drivers/net/virtio_net.c:4551:17: note: ‘sprintf’ output between 8 and 18 bytes into a destination of size 16
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4552:49: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 9 [-Wformat-overflow=]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4552:41: note: directive argument in the range [-2147483643, 65534]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~~~~~~~~~~
drivers/net/virtio_net.c:4552:17: note: ‘sprintf’ output between 9 and 19 bytes into a destination of size 16
4552 | sprintf(vi->sq[i].name, "output.%d", i);
"
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Link: https://lore.kernel.org/r/20240104020902.2753599-1-yanjun.zhu@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e1010cda7967cfca9c8650ee1f4efcae54ab90 ]
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec38 ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ebb1f95e0c3c3e0eec5bb21aa43097580c4b6e4 ]
As of today, the last MCAM entry was not getting allocated because of
a <= check with the max_bmap count. This patch modifies that and if the
requested entry is greater than the available entries then set it to the
max value.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20240101145042.419697-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31deb12e85c35ddd2c037f0107d05d8674cab2c0 ]
Currently, if a VF is disabled using the
'ip link set dev $ETHX vf $VF_NUM state disable' command, the VF is still
able to receive traffic.
Fix the behavior of the 'ip link set dev $ETHX vf $VF_NUM state disable'
to completely shutdown the VF's queues making it entirely disabled and
not able to receive or send any traffic.
Modify the behavior of the 'ip link set $ETHX vf $VF_NUM state enable'
command to make a VF do reinitialization bringing the queues back up.
Co-developed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c16618bc06a41ad68fd8499a21d35ef57ca06c2 ]
Using calculate_bit_shift() to replace rtl8723_phy_calculate_bit_shift().
And fix an undefined bitwise shift behavior problem.
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-12-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e87ca403e2008b9e182239e1abbf6876a55eb33 ]
Add additional USB IDs found in the vendor driver from
https://github.com/Mange/rtl8192eu-linux-driver to support more
RTL8192EU devices.
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231217123017.1982-1-zenmchen@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7173be21ae29ef50ada42fd4464056a9d3f55bb3 ]
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc82a08ae795ee6b73fb6b50785f7be248bec7b5 ]
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3cb7a830a24527877b0bc900b9bd74a96aea928 ]
Driver has a logic leak in ring data allocation/free,
where aq_ring_free could be called multiple times on same ring,
if system is under stress and got memory allocation error.
Ring pointer was used as an indicator of failure, but this is
not correct since only ring data is allocated/deallocated.
Ring itself is an array member.
Changing ring allocation functions to return error code directly.
This simplifies error handling and eliminates aq_ring_free
on higher layer.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20231213095044.23146-1-irusskikh@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20f73b60bb5c276cee9b1a530f100c677bc74af8 ]
Fix the values of the ICE_AQ_VSI_Q_OPT_RSS_* registers. Shifting is
already done when the values are used, no need to double shift. Bug was
not discovered earlier since only ICE_AQ_VSI_Q_OPT_RSS_TPLZ (Zero) is
currently used.
Also, rename ICE_AQ_VSI_Q_OPT_RSS_XXX to ICE_AQ_VSI_Q_OPT_RSS_HASH_XXX
for consistency.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-5-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca5fdf9a7c5b65968c718f2be159cda4c13556a1 ]
If the driver or firmware is stuck in reset state, don't bother
trying to use adminq commands. This speeds up shutdown and
prevents unnecessary timeouts and error messages.
This includes a bit of rework on ionic_adminq_post_wait()
and ionic_adminq_post_wait_nomsg() to both use
__ionic_adminq_post_wait() which can do the checks needed in
both cases.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 24f110240c03c6b5368f1203bac72883d511e606 ]
Don't rely on the PCI memory for the devcmd opcode because we
read a 0xff value if the PCI bus is broken, which can cause us
to report a bogus dev_cmd opcode later.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8fdbf3389f44c7026f16e36cb1f2ff017f7f5b2 ]
Fix passing the wrong reference for config_initr on passing the function
pointer, drop the wrong & from at803x_config_intr in the PHY struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe0a7776d4d19e613bb8dd80fe2d78ae49e8b49d ]
Since 'ieee80211_beacon_get()' can return NULL, 'wfx_set_mfp_ap()'
should check the return value before examining skb data. So convert
the latter to return an appropriate error code and propagate it to
return from 'wfx_start_ap()' as well. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Tested-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231204171130.141394-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5082b3e3027eae393a4e86874bffb4ce3f83c26e ]
We are seeing below error randomly in the case where only
one MSI vector is configured:
kernel: ath11k_pci 0000:03:00.0: wmi command 16387 timeout
The reason is, currently, in ath11k_pcic_ext_irq_enable(),
ATH11K_FLAG_EXT_IRQ_ENABLED is set before NAPI is enabled.
This results in a race condition: after
ATH11K_FLAG_EXT_IRQ_ENABLED is set but before NAPI enabled,
CE interrupt breaks in. Since IRQ is shared by CE and data
path, ath11k_pcic_ext_interrupt_handler() is also called
where we call disable_irq_nosync() to disable IRQ. Then
napi_schedule() is called but it does nothing because NAPI
is not enabled at that time, meaning
ath11k_pcic_ext_grp_napi_poll() will never run, so we have
no chance to call enable_irq() to enable IRQ back. Finally
we get above error.
Fix it by setting ATH11K_FLAG_EXT_IRQ_ENABLED after all
NAPI and IRQ work are done. With the fix, we are sure that
by the time ATH11K_FLAG_EXT_IRQ_ENABLED is set, NAPI is
enabled.
Note that the fix above also introduce some side effects:
if ath11k_pcic_ext_interrupt_handler() breaks in after NAPI
enabled but before ATH11K_FLAG_EXT_IRQ_ENABLED set, nothing
will be done by the handler this time, the work will be
postponed till the next time the IRQ fires.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231117003919.26218-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2adc886244dff60f948497b59affb6c6ebb3c348 ]
Fix an array-index-out-of-bounds read in ath9k_htc_txstatus(). The bug
occurs when txs->cnt, data from a URB provided by a USB device, is
bigger than the size of the array txs->txstatus, which is
HTC_MAX_TX_STATUS. WARN_ON() already checks it, but there is no bug
handling code after the check. Make the function return if that is the
case.
Found by a modified version of syzkaller.
UBSAN: array-index-out-of-bounds in htc_drv_txrx.c
index 13 is out of range for type '__wmi_event_txstatus [12]'
Call Trace:
ath9k_htc_txstatus
ath9k_wmi_event_tasklet
tasklet_action_common
__do_softirq
irq_exit_rxu
sysvec_apic_timer_interrupt
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231113065756.1491991-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2689b6a86b9d23574bd4b654bf770b6034e2c7e ]
The device is always reset two consecutive times (ax88179_reset is called
twice), one from usbnet_probe during the device binding and the other from
usbnet_open.
Remove the non-necessary reset during the device binding and let the reset
operation from open to keep the normal behavior (tested with generic ASIX
Electronics Corp. AX88179 Gigabit Ethernet device).
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120121239.54504-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
