IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 83ef106fa732aea8558253641cd98e8a895604d7 ]
For i2c read operation in GSI mode, we are getting timeout
due to malformed TRE basically incorrect TRE sequence
in gpi(drivers/dma/qcom/gpi.c) driver.
I2C driver has geni_i2c_gpi(I2C_WRITE) function which generates GO TRE and
geni_i2c_gpi(I2C_READ)generates DMA TRE. Hence to generate GO TRE before
DMA TRE, we should move geni_i2c_gpi(I2C_WRITE) before
geni_i2c_gpi(I2C_READ) inside the I2C GSI mode transfer function
i.e. geni_i2c_gpi_xfer().
TRE stands for Transfer Ring Element - which is basically an element with
size of 4 words. It contains all information like slave address,
clk divider, dma address value data size etc).
Mainly we have 3 TREs(Config, GO and DMA tre).
- CONFIG TRE : consists of internal register configuration which is
required before start of the transfer.
- DMA TRE : contains DDR/Memory address, called as DMA descriptor.
- GO TRE : contains Transfer directions, slave ID, Delay flags, Length
of the transfer.
I2c driver calls GPI driver API to config each TRE depending on the
protocol.
For read operation tre sequence will be as below which is not aligned
to hardware programming guide.
- CONFIG tre
- DMA tre
- GO tre
As per Qualcomm's internal Hardware Programming Guide, we should configure
TREs in below sequence for any RX only transfer.
- CONFIG tre
- GO tre
- DMA tre
Fixes: d8703554f4de ("i2c: qcom-geni: Add support for GPI DMA")
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # qrb5165-rb5
Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cffe487026be13eaf37ea28b783d9638ab147204 ]
In this loop, we step through the buffer and after each item we check
if the size_left is greater than the minimum size we need. However,
the problem is that "bytes_left" is type ssize_t while sizeof() is type
size_t. That means that because of type promotion, the comparison is
done as an unsigned and if we have negative bytes left the loop
continues instead of ending.
Fixes: fe856be475f7 ("CIFS: parse and store info on iface queries")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a7aee96200ad281a5cc4cf5c7a2e2a49d2b97b0 ]
In kasan_init_region, when k_start is not page aligned, at the begin of
for loop, k_cur = k_start & PAGE_MASK is less than k_start, and then
`va = block + k_cur - k_start` is less than block, the addr va is invalid,
because the memory address space from va to block is not alloced by
memblock_alloc, which will not be reserved by memblock_reserve later, it
will be used by other places.
As a result, memory overwriting occurs.
for example:
int __init __weak kasan_init_region(void *start, size_t size)
{
[...]
/* if say block(dcd97000) k_start(feef7400) k_end(feeff3fe) */
block = memblock_alloc(k_end - k_start, PAGE_SIZE);
[...]
for (k_cur = k_start & PAGE_MASK; k_cur < k_end; k_cur += PAGE_SIZE) {
/* at the begin of for loop
* block(dcd97000) va(dcd96c00) k_cur(feef7000) k_start(feef7400)
* va(dcd96c00) is less than block(dcd97000), va is invalid
*/
void *va = block + k_cur - k_start;
[...]
}
[...]
}
Therefore, page alignment is performed on k_start before
memblock_alloc() to ensure the validity of the VA address.
Fixes: 663c0c9496a6 ("powerpc/kasan: Fix shadow area set up for modules.")
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/1705974359-43790-1-git-send-email-xiaojiangfeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6442d79d880cf7a2fff18779265d657fef0cce4c ]
fw_devlink can detect most overlapping/intersecting cycles. However it was
missing a few corner cases because of an incorrect optimization logic that
tries to avoid repeating cycle detection for devices that are already
marked as part of a cycle.
Here's an example provided by Xu Yang (edited for clarity):
usb
+-----+
tcpc | |
+-----+ | +--|
| |----------->|EP|
|--+ | | +--|
|EP|<-----------| |
|--+ | | B |
| | +-----+
| A | |
+-----+ |
^ +-----+ |
| | | |
+-----| C |<--+
| |
+-----+
usb-phy
Node A (tcpc) will be populated as device 1-0050.
Node B (usb) will be populated as device 38100000.usb.
Node C (usb-phy) will be populated as device 381f0040.usb-phy.
The description below uses the notation:
consumer --> supplier
child ==> parent
1. Node C is populated as device C. No cycles detected because cycle
detection is only run when a fwnode link is converted to a device link.
2. Node B is populated as device B. As we convert B --> C into a device
link we run cycle detection and find and mark the device link/fwnode
link cycle:
C--> A --> B.EP ==> B --> C
3. Node A is populated as device A. As we convert C --> A into a device
link, we see it's already part of a cycle (from step 2) and don't run
cycle detection. Thus we miss detecting the cycle:
A --> B.EP ==> B --> A.EP ==> A
Looking at it another way, A depends on B in one way:
A --> B.EP ==> B
But B depends on A in two ways and we only detect the first:
B --> C --> A
B --> A.EP ==> A
To detect both of these, we remove the incorrect optimization attempt in
step 3 and run cycle detection even if the fwnode link from which the
device link is being created has already been marked as part of a cycle.
Reported-by: Xu Yang <xu.yang_2@nxp.com>
Closes: https://lore.kernel.org/lkml/DU2PR04MB8822693748725F85DC0CB86C8C792@DU2PR04MB8822.eurprd04.prod.outlook.com/
Fixes: 3fb16866b51d ("driver core: fw_devlink: Make cycle detection more robust")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240202095636.868578-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc9ceb90c4b42c6e5c6757df1d6257110433788e ]
When irtoy_command fails, buf should be freed since it is allocated by
irtoy_tx, or there is a memleak.
Fixes: 4114978dcd24 ("media: ir_toy: prevent device from hanging during transmit")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85e985a4f46e462a37f1875cb74ed380e7c0c2e0 ]
The CO0 BCM needs to be up at all times, otherwise some hardware (like
the UFS controller) loses its connection to the rest of the SoC,
resulting in a hang of the platform, accompanied by a spectacular
logspam.
Mark it as keepalive to prevent such cases.
Fixes: 9c8c6bac1ae8 ("interconnect: qcom: Add SC8180x providers")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231214-topic-sc8180_fixes-v1-1-421904863006@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 61a348857e869432e6a920ad8ea9132e8d44c316 upstream.
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c29 ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2d2d7ea0dd09802cf5a0545bf54d8ad8987d20c upstream.
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f17c34ffc792bbb520e4b61baa16b6cfc7d44b13 upstream.
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44269 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2840143e393a4ddc1caab4372969ea337371168c upstream.
In case of a spurious or otherwise delayed notification it is
possible that CCI still reports the previous completion. The
UCSI spec is aware of this and provides two completion bits in
CCI, one for normal commands and one for acks. As acks and commands
alternate the notification handler can determine if the completion
bit is from the current command.
The initial UCSI code correctly handled this but the distinction
between the two completion bits was lost with the introduction of
the new API.
To fix this revive the ACK_PENDING bit for ucsi_acpi and only complete
commands if the completion bit matches.
Fixes: f56de278e8ec ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-3-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3caf2b2ad7334ef35f55b95f3e1b138c6f77b368 upstream.
The ULPI per-device debugfs root is named after the ulpi device's
parent, but ulpi_unregister_interface tries to remove a debugfs
directory named after the ulpi device itself. This results in the
directory sticking around and preventing subsequent (deferred) probes
from succeeding. Change the directory name to match the ulpi device.
Fixes: bd0a0a024f2a ("usb: ulpi: Add debugfs support")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240126223800.2864613-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9aed03a0a683fd1600ea92f2ad32232d4736272 upstream.
Calling ->sync_write must be done while holding the PPM lock as
the mailbox logic does not support concurrent commands.
At least since the addition of partner task this means that
ucsi_acknowledge_connector_change should be called with the
PPM lock held as it calls ->sync_write.
Thus protect the only call to ucsi_acknowledge_connector_change
with the PPM. All other calls to ->sync_write already happen
under the PPM lock.
Fixes: b9aa02ca39a4 ("usb: typec: ucsi: Add polling mechanism for partner tasks like alt mode checking")
Cc: stable@vger.kernel.org
Signed-off-by: "Christian A. Ehrhardt" <lk@c--e.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240121204123.275441-2-lk@c--e.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 621c6257128149e45b36ffb973a01c3f3461b893 upstream.
When als_capture_sample() is called with usage ID
HID_USAGE_SENSOR_TIME_TIMESTAMP, return 0. The HID sensor core ignores
the return value for capture_sample() callback, so return value doesn't
make difference. But correct the return value to return success instead
of -EINVAL.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240204125617.2635574-1-srinivas.pandruvada@linux.intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1d6708bf0d3dd976460d435373cf5abf21ce258 upstream.
If a input device is opened before hid_hw_start is called, events may
not be received from the hardware. In the case of USB-backed devices,
for example, the hid_hw_start function is responsible for filling in
the URB which is submitted when the input device is opened. If a device
is opened prematurely, polling will never start because the device will
not have been in the correct state to send the URB.
Because the wacom driver registers its input devices before calling
hid_hw_start, there is a window of time where a device can be opened
and end up in an inoperable state. Some ARM-based Chromebooks in particular
reliably trigger this bug.
This commit splits the wacom_register_inputs function into two pieces.
One which is responsible for setting up the allocated inputs (and runs
prior to hid_hw_start so that devices are ready for any input events
they may end up receiving) and another which only registers the devices
(and runs after hid_hw_start to ensure devices can be immediately opened
without issue). Note that the functions to initialize the LEDs and remotes
are also moved after hid_hw_start to maintain their own dependency chains.
Fixes: 7704ac937345 ("HID: wacom: implement generic HID handling for pen generic devices")
Cc: stable@vger.kernel.org # v3.18+
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab41a31dd5e2681803642b6d08590b61867840ec upstream.
The xf86-input-wacom driver does not treat '0' as a valid serial
number and will drop any input report which contains an
MSC_SERIAL = 0 event. The kernel driver already takes care to
avoid sending any MSC_SERIAL event if the value of serial[0] == 0
(which is the case for devices that don't actually report a
serial number), but this is not quite sufficient.
Only the lower 32 bits of the serial get reported to userspace,
so if this portion of the serial is zero then there can still
be problems.
This commit allows the driver to report either the lower 32 bits
if they are non-zero or the upper 32 bits otherwise.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Fixes: f85c9dc678a5 ("HID: wacom: generic: Support tool ID and additional tool types")
CC: stable@vger.kernel.org # v4.10
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00aab7dcb2267f2aef59447602f34501efe1a07f upstream.
A while back the I2C HID implementation was split in an ACPI and OF
part, but the new OF driver never initialises the client pointer which
is dereferenced on power-up failures.
Fixes: b33752c30023 ("HID: i2c-hid: Reorganize so ACPI and OF are separate modules")
Cc: stable@vger.kernel.org # 5.12
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb56d84dd9c3de3c99fc396abb57c6d330038b5 upstream.
If you connect an external headset/microphone to the 3.5mm jack on the
Acer Swift 1 SF114-32 it does not recognize the microphone. This fixes
that and gives the user the ability to choose between internal and
headset mic.
Signed-off-by: David Senoner <seda18@rolmail.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240126155626.2304465-1-seda18@rolmail.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8708d758e715c3824a73bf0cda97292b52be44d upstream.
Printing the inventory on a serial console can be quite slow and thus may
trigger the hung task detector (CONFIG_DETECT_HUNG_TASK=y) and possibly
reboot the machine. Adding a cond_resched() prevents this.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v6.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dce23ec993f7da7790a9eadb36864ceb60e942 upstream.
The laptop requires a quirk ID to enable its internal microphone. Add
it to the DMI quirk table.
Reported-by: Techno Mooney <techno.mooney@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218402
Cc: stable@vger.kernel.org
Signed-off-by: Techno Mooney <techno.mooney@gmail.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://msgid.link/r/20240129081148.1044891-1-bagasdotme@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0a9bab391e336489169b95cb0d4553d921302189 upstream.
Tasklets have an inherent problem with memory corruption. The function
tasklet_action_common calls tasklet_trylock, then it calls the tasklet
callback and then it calls tasklet_unlock. If the tasklet callback frees
the structure that contains the tasklet or if it calls some code that may
free it, tasklet_unlock will write into free memory.
The commits 8e14f610159d and d9a02e016aaf try to fix it for dm-crypt, but
it is not a sufficient fix and the data corruption can still happen [1].
There is no fix for dm-verity and dm-verity will write into free memory
with every tasklet-processed bio.
There will be atomic workqueues implemented in the kernel 6.9 [2]. They
will have better interface and they will not suffer from the memory
corruption problem.
But we need something that stops the memory corruption now and that can be
backported to the stable kernels. So, I'm proposing this commit that
disables tasklets in both dm-crypt and dm-verity. This commit doesn't
remove the tasklet support, because the tasklet code will be reused when
atomic workqueues will be implemented.
[1] https://lore.kernel.org/all/d390d7ee-f142-44d3-822a-87949e14608b@suse.de/T/
[2] https://lore.kernel.org/lkml/20240130091300.2968534-1-tj@kernel.org/
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 39d42fa96ba1b ("dm crypt: add flags to optionally bypass kcryptd workqueues")
Fixes: 5721d4e5a9cdb ("dm verity: Add optional "try_verify_in_tasklet" feature")
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4469f3858352ad1197434557150b1f7086762a0 upstream.
Current code uses the specified ring buffer size (either the default of 128
Kbytes or a module parameter specified value) to encompass the one page
ring buffer header plus the actual ring itself. When the page size is 4K,
carving off one page for the header isn't significant. But when the page
size is 64K on ARM64, only half of the default 128 Kbytes is left for the
actual ring. While this doesn't break anything, the smaller ring size
could be a performance bottleneck.
Fix this by applying the VMBUS_RING_SIZE macro to the specified ring buffer
size. This macro adds a page for the header, and rounds up the size to a
page boundary, using the page size for which the kernel is built. Use this
new size for subsequent ring buffer calculations. For example, on ARM64
with 64K page size and the default ring size, this results in the actual
ring being 128 Kbytes, which is intended.
Cc: stable@vger.kernel.org # 5.15.x
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240122170956.496436-1-mhklinux@outlook.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9319b647902cbd5cc884ac08a8a6d54ce111fc78 upstream.
(struct dirty_throttle_control *)->thresh is an unsigned long, but is
passed as the u32 divisor argument to div_u64(). On architectures where
unsigned long is 64 bytes, the argument will be implicitly truncated.
Use div64_u64() instead of div_u64() so that the value used in the "is
this a safe division" check is the same as the divisor.
Also, remove redundant cast of the numerator to u64, as that should happen
implicitly.
This would be difficult to exploit in memcg domain, given the ratio-based
arithmetic domain_drity_limits() uses, but is much easier in global
writeback domain with a BDI_CAP_STRICTLIMIT-backing device, using e.g.
vm.dirty_bytes=(1<<32)*PAGE_SIZE so that dtc->thresh == (1<<32)
Link: https://lkml.kernel.org/r/20240118181954.1415197-1-zokeefe@google.com
Fixes: f6789593d5ce ("mm/page-writeback.c: fix divide by zero in bdi_dirty_limits()")
Signed-off-by: Zach O'Keefe <zokeefe@google.com>
Cc: Maxim Patlasov <MPatlasov@parallels.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0958b33ef5a04ed91f61cef4760ac412080c4e08 upstream.
Fix register_snapshot_trigger() to return error code if it failed to
allocate a snapshot instead of 0 (success). Unless that, it will register
snapshot trigger without an error.
Link: https://lore.kernel.org/linux-trace-kernel/170622977792.270660.2789298642759362200.stgit@devnote2
Fixes: 0bbe7f719985 ("tracing: Fix the race between registering 'snapshot' event trigger and triggering 'snapshot' operation")
Cc: stable@vger.kernel.org
Cc: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c73729b64bb692186da080602cd13612783f52ac ]
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39fac ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73d9629e1c8c1982f13688c4d1019c3994647ccc ]
Currently when PF administratively sets VF's MAC address and the VF
is put down (VF tries to delete all MACs) then the MAC is removed
from MAC filters and primary VF MAC is zeroed.
Do not allow untrusted VF to remove primary MAC when it was set
administratively by PF.
Reproducer:
1) Create VF
2) Set VF interface up
3) Administratively set the VF's MAC
4) Put VF interface down
[root@host ~]# echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
[root@host ~]# ip link set enp2s0f0v0 up
[root@host ~]# ip link set enp2s0f0 vf 0 mac fe:6c:b5:da:c7:7d
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether fe:6c:b5:da:c7:7d brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
[root@host ~]# ip link set enp2s0f0v0 down
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
Fixes: 700bbf6c1f9e ("i40e: allow VF to remove any MAC filter")
Fixes: ceb29474bbbc ("i40e: Add support for VF to specify its primary MAC address")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240208180335.1844996-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d55347bfe4e66dce2e1e7501e5492f4af3e315f8 ]
After 'lib: checksum: Use aligned accesses for ip_fast_csum and
csum_ipv6_magic tests' was applied, the test_csum_ipv6_magic unit test
started failing for all mips platforms, both little and bit endian.
Oddly enough, adding debug code into test_csum_ipv6_magic() made the
problem disappear.
The gcc manual says:
"The "memory" clobber tells the compiler that the assembly code performs
memory reads or writes to items other than those listed in the input
and output operands (for example, accessing the memory pointed to by one
of the input parameters)
"
This is definitely the case for csum_ipv6_magic(). Indeed, adding the
'memory' clobber fixes the problem.
Cc: Charlie Jenkins <charlie@rivosinc.com>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Charlie Jenkins <charlie@rivosinc.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c80a2b715df75881359d07dbaacff8ad411f40e ]
The conversion to kvcalloc() mixed up the object size and count
arguments, causing a warning:
drivers/gpu/drm/nouveau/nouveau_svm.c: In function 'nouveau_svm_fault_buffer_ctor':
drivers/gpu/drm/nouveau/nouveau_svm.c:1010:40: error: 'kvcalloc' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
1010 | buffer->fault = kvcalloc(sizeof(*buffer->fault), buffer->entries, GFP_KERNEL);
| ^
drivers/gpu/drm/nouveau/nouveau_svm.c:1010:40: note: earlier argument should specify number of elements, later size of each element
The behavior is still correct aside from the warning, but fixing it avoids
the warnings and can help the compiler track the individual objects better.
Fixes: 71e4bbca070e ("nouveau/svm: Use kvcalloc() instead of kvzalloc()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212112230.1117284-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b3fbd61b9d1f4ed2db95aaf03f9adae0373784d ]
The Documentation/ABI/testing/sysfs-class-net-statistics documentation
is pointing to the wrong path for the interface. Documentation is
pointing to /sys/class/<iface>, instead of /sys/class/net/<iface>.
Fix it by adding the `net/` directory before the interface.
Fixes: 6044f9700645 ("net: sysfs: document /sys/class/net/statistics/*")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef5d5b92f7117b324efaac72b3db27ae8bb3082 ]
There is a path in rt5645_jack_detect_work(), where rt5645->jd_mutex
is left locked forever. That may lead to deadlock
when rt5645_jack_detect_work() is called for the second time.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: cdba4301adda ("ASoC: rt5650: add mutex to avoid the jack detection failure")
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/1707645514-21196-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3aa619a8b4706f35cb62f780c14e68796b37f3f ]
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
Fixes: 24778be20f87 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac437a51ce662364062f704e321227f6728e6adc ]
We double count async, non-zc rx data. The previous fix was
lucky because if we fully zc async_copy_bytes is 0 so we add 0.
Decrypted already has all the bytes we handled, in all cases.
We don't have to adjust anything, delete the erroneous line.
Fixes: 4d42cd6bc2ac ("tls: rx: fix return value for async crypto")
Co-developed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32b55c5ff9103b8508c1e04bfa5a08c64e7a925f ]
tls_decrypt_sg doesn't take a reference on the pages from clear_skb,
so the put_page() in tls_decrypt_done releases them, and we trigger
a use-after-free in process_rx_list when we try to read from the
partially-read skb.
Fixes: fd31f3996af2 ("tls: rx: decrypt into a fresh skb")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aec7961916f3f9e88766e2688992da6980f11b8d ]
The submitting thread (one which called recvmsg/sendmsg)
may exit as soon as the async crypto handler calls complete()
so any code past that point risks touching already freed data.
Try to avoid the locking and extra flags altogether.
Have the main thread hold an extra reference, this way
we can depend solely on the atomic ref counter for
synchronization.
Don't futz with reiniting the completion, either, we are now
tightly controlling when completion fires.
Reported-by: valis <sec@valis.email>
Fixes: 0cada33241d9 ("net/tls: fix race condition causing kernel panic")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c57ca512f3b68ddcd62bda9cc24a8f5584ab01b1 ]
Factor out waiting for async encrypt and decrypt to finish.
There are already multiple copies and a subsequent fix will
need more. No functional changes.
Note that crypto_wait_req() returns wait->err
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aec7961916f3 ("tls: fix race between async notify and socket close")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df720d288dbb1793e82b6ccbfc670ec871e9def4 ]
Allow splice to end a TLS record after prematurely ending a splice/sendfile
due to getting an EOF condition (->splice_read() returned 0) after splice
had called TLS with a sendmsg() with MSG_MORE set when the user didn't set
MSG_MORE.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
cc: Chuck Lever <chuck.lever@oracle.com>
cc: Boris Pismenny <borisp@nvidia.com>
cc: John Fastabend <john.fastabend@gmail.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: aec7961916f3 ("tls: fix race between async notify and socket close")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15faa1f67ab405d47789d4702f587ec7df7ef03e ]
There is a crash when adding one of the lan966x interfaces under a lag
interface. The issue can be reproduced like this:
ip link add name bond0 type bond miimon 100 mode balance-xor
ip link set dev eth0 master bond0
The reason is because when adding a interface under the lag it would go
through all the ports and try to figure out which other ports are under
that lag interface. And the issue is that lan966x can have ports that are
NULL pointer as they are not probed. So then iterating over these ports
it would just crash as they are NULL pointers.
The fix consists in actually checking for NULL pointers before accessing
something from the ports. Like we do in other places.
Fixes: cabc9d49333d ("net: lan966x: Add lag support for lan966x")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206123054.3052966-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6e2f90d31fe09f2b852de25125ca875aabd81367 ]
The ovs module allows for some actions to recursively contain an action
list for complex scenarios, such as sampling, checking lengths, etc.
When these actions are copied into the internal flow table, they are
evaluated to validate that such actions make sense, and these calls
happen recursively.
The ovs-vswitchd userspace won't emit more than 16 recursion levels
deep. However, the module has no such limit and will happily accept
limits larger than 16 levels nested. Prevent this by tracking the
number of recursions happening and manually limiting it to 16 levels
nested.
The initial implementation of the sample action would track this depth
and prevent more than 3 levels of recursion, but this was removed to
support the clone use case, rather than limited at the current userspace
limit.
Fixes: 798c166173ff ("openvswitch: Optimize sample action for the clone use cases")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240207132416.1488485-2-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 782bfd03c3ae2c0e6e01b661b8e18f1de50357be ]
After commit 4a032827daa8 ("of: property: Simplify of_link_to_phandle()"),
remote-endpoint properties created a fwnode link from the consumer device
to the supplier endpoint. This is a tiny bit inefficient (not buggy) when
trying to create device links or detecting cycles. So, improve this the
same way we improved finding the consumer of a remote-endpoint property.
Fixes: 4a032827daa8 ("of: property: Simplify of_link_to_phandle()")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20240207011803.2637531-3-saravanak@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65c6ee90455053cfd3067c17aaa4a42b0c766543 ]
This is an error path and Smatch complains that "tbl_rev" is uninitialized
on this path. All the other functions follow this same patter where they
set the error code and goto out_free so that's probably what was intended
here as well.
Fixes: e8e10a37c51c ("iwlwifi: acpi: move ppag code from mvm to fw/acpi")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/09900c01-6540-4a32-9451-563da0029cb6@moroto.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ebb5b67641994de8bc486b33457fe0b681d6fe ]
This saves the error as PTR_ERR(wifi_pkg). The problem is that
"wifi_pkg" is a valid pointer, not an error pointer. Set the error code
to -EINVAL instead.
Fixes: 2a8084147bff ("iwlwifi: acpi: support reading and storing WRDS revision 1 and 2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/9620bb77-2d7c-4d76-b255-ad824ebf8e35@moroto.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba58f873cdeec30b6da48e28dd5782c5a3e1371b ]
When finishing the final iteration of dirty_log_test testcase, set
host_quit _before_ the final "continue" so that the vCPU worker doesn't
run an extra iteration, and delete the hack-a-fix of an extra "continue"
from the dirty ring testcase. This fixes a bug where the extra post to
sem_vcpu_cont may not be consumed, which results in failures in subsequent
runs of the testcases. The bug likely was missed during development as
x86 supports only a single "guest mode", i.e. there aren't any subsequent
testcases after the dirty ring test, because for_each_guest_mode() only
runs a single iteration.
For the regular dirty log testcases, letting the vCPU run one extra
iteration is a non-issue as the vCPU worker waits on sem_vcpu_cont if and
only if the worker is explicitly told to stop (vcpu_sync_stop_requested).
But for the dirty ring test, which needs to periodically stop the vCPU to
reap the dirty ring, letting the vCPU resume the guest _after_ the last
iteration means the vCPU will get stuck without an extra "continue".
However, blindly firing off an post to sem_vcpu_cont isn't guaranteed to
be consumed, e.g. if the vCPU worker sees host_quit==true before resuming
the guest. This results in a dangling sem_vcpu_cont, which leads to
subsequent iterations getting out of sync, as the vCPU worker will
continue on before the main task is ready for it to resume the guest,
leading to a variety of asserts, e.g.
==== Test Assertion Failure ====
dirty_log_test.c:384: dirty_ring_vcpu_ring_full
pid=14854 tid=14854 errno=22 - Invalid argument
1 0x00000000004033eb: dirty_ring_collect_dirty_pages at dirty_log_test.c:384
2 0x0000000000402d27: log_mode_collect_dirty_pages at dirty_log_test.c:505
3 (inlined by) run_test at dirty_log_test.c:802
4 0x0000000000403dc7: for_each_guest_mode at guest_modes.c:100
5 0x0000000000401dff: main at dirty_log_test.c:941 (discriminator 3)
6 0x0000ffff9be173c7: ?? ??:0
7 0x0000ffff9be1749f: ?? ??:0
8 0x000000000040206f: _start at ??:?
Didn't continue vcpu even without ring full
Alternatively, the test could simply reset the semaphores before each
testcase, but papering over hacks with more hacks usually ends in tears.
Reported-by: Shaoqin Huang <shahuang@redhat.com>
Fixes: 84292e565951 ("KVM: selftests: Add dirty ring buffer test")
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Link: https://lore.kernel.org/r/20240202231831.354848-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7167190ddb863bd061c0c6b61f4cec94184b40da ]
There are two states, which need to be cleared before next mode
is executed. Otherwise, we will hit failure as the following messages
indicate.
- The variable 'dirty_ring_vcpu_ring_full' shared by main and vcpu
thread. It's indicating if the vcpu exit due to full ring buffer.
The value can be carried from previous mode (VM_MODE_P40V48_4K) to
current one (VM_MODE_P40V48_64K) when VM_MODE_P40V48_16K isn't
supported.
- The current ring buffer index needs to be reset before next mode
(VM_MODE_P40V48_64K) is executed. Otherwise, the stale value is
carried from previous mode (VM_MODE_P40V48_4K).
# ./dirty_log_test -M dirty-ring
Setting log mode to: 'dirty-ring'
Test iterations: 32, interval: 10 (ms)
Testing guest mode: PA-bits:40, VA-bits:48, 4K pages
guest physical test memory offset: 0xffbfffc000
:
Dirtied 995328 pages
Total bits checked: dirty (1012434), clear (7114123), track_next (966700)
Testing guest mode: PA-bits:40, VA-bits:48, 64K pages
guest physical test memory offset: 0xffbffc0000
vcpu stops because vcpu is kicked out...
vcpu continues now.
Notifying vcpu to continue
Iteration 1 collected 0 pages
vcpu stops because dirty ring is full...
vcpu continues now.
vcpu stops because dirty ring is full...
vcpu continues now.
vcpu stops because dirty ring is full...
==== Test Assertion Failure ====
dirty_log_test.c:369: cleared == count
pid=10541 tid=10541 errno=22 - Invalid argument
1 0x0000000000403087: dirty_ring_collect_dirty_pages at dirty_log_test.c:369
2 0x0000000000402a0b: log_mode_collect_dirty_pages at dirty_log_test.c:492
3 (inlined by) run_test at dirty_log_test.c:795
4 (inlined by) run_test at dirty_log_test.c:705
5 0x0000000000403a37: for_each_guest_mode at guest_modes.c:100
6 0x0000000000401ccf: main at dirty_log_test.c:938
7 0x0000ffff9ecd279b: ?? ??:0
8 0x0000ffff9ecd286b: ?? ??:0
9 0x0000000000401def: _start at ??:?
Reset dirty pages (0) mismatch with collected (35566)
Fix the issues by clearing 'dirty_ring_vcpu_ring_full' and the ring
buffer index before next new mode is to be executed.
Signed-off-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221110104914.31280-7-gshan@redhat.com
Stable-dep-of: ba58f873cdee ("KVM: selftests: Fix a semaphore imbalance in the dirty ring logging test")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 607aad1e4356c210dbef9022955a3089377909b2 ]
If CONFIG_OF_KOBJ is not set, a device_node does not contain a
kobj and attempts to access the embedded kobj via kref_read break
the compile.
Replace affected kref_read calls with a macro that reads the
refcount if it exists and returns 1 if there is no embedded kobj.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401291740.VP219WIz-lkp@intel.com/
Fixes: 4dde83569832 ("of: Fix double free in of_parse_phandle_with_args_map")
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Link: https://lore.kernel.org/r/20240129192556.403271-1-lk@c--e.de
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7fddac12c38237252431d5b8af7b6d5771b6d125 upstream.
device_link_flag_is_sync_state_only() correctly returns true on the flags
of an existing device link that only implements sync_state() functionality.
However, it incorrectly and confusingly returns false if it's called with
DL_FLAG_SYNC_STATE_ONLY.
This bug doesn't manifest in any of the existing calls to this function,
but fix this confusing behavior to avoid future bugs.
Fixes: 67cad5c67019 ("driver core: fw_devlink: Add DL_FLAG_CYCLE support to device links")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240202095636.868578-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5571e41ec6e56e35f34ae9f5b3a335ef510e0ade upstream.
While running the CI for an unrelated change I hit the following panic
with generic/648 on btrfs_holes_spacecache.
assertion failed: block_start != EXTENT_MAP_HOLE, in fs/btrfs/extent_io.c:1385
------------[ cut here ]------------
kernel BUG at fs/btrfs/extent_io.c:1385!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 2695096 Comm: fsstress Kdump: loaded Tainted: G W 6.8.0-rc2+ #1
RIP: 0010:__extent_writepage_io.constprop.0+0x4c1/0x5c0
Call Trace:
<TASK>
extent_write_cache_pages+0x2ac/0x8f0
extent_writepages+0x87/0x110
do_writepages+0xd5/0x1f0
filemap_fdatawrite_wbc+0x63/0x90
__filemap_fdatawrite_range+0x5c/0x80
btrfs_fdatawrite_range+0x1f/0x50
btrfs_write_out_cache+0x507/0x560
btrfs_write_dirty_block_groups+0x32a/0x420
commit_cowonly_roots+0x21b/0x290
btrfs_commit_transaction+0x813/0x1360
btrfs_sync_file+0x51a/0x640
__x64_sys_fdatasync+0x52/0x90
do_syscall_64+0x9c/0x190
entry_SYSCALL_64_after_hwframe+0x6e/0x76
This happens because we fail to write out the free space cache in one
instance, come back around and attempt to write it again. However on
the second pass through we go to call btrfs_get_extent() on the inode to
get the extent mapping. Because this is a new block group, and with the
free space inode we always search the commit root to avoid deadlocking
with the tree, we find nothing and return a EXTENT_MAP_HOLE for the
requested range.
This happens because the first time we try to write the space cache out
we hit an error, and on an error we drop the extent mapping. This is
normal for normal files, but the free space cache inode is special. We
always expect the extent map to be correct. Thus the second time
through we end up with a bogus extent map.
Since we're deprecating this feature, the most straightforward way to
fix this is to simply skip dropping the extent map range for this failed
range.
I shortened the test by using error injection to stress the area to make
it easier to reproduce. With this patch in place we no longer panic
with my error injection test.
CC: stable@vger.kernel.org # 4.14+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1bd96c92c6a0a4d43815eb685c15aa4b78879dc9 upstream.
Currently we allow an encoded write against inodes that have the NODATASUM
flag set, either because they are NOCOW files or they were created while
the filesystem was mounted with "-o nodatasum". This results in having
compressed extents without corresponding checksums, which is a filesystem
inconsistency reported by 'btrfs check'.
For example, running btrfs/281 with MOUNT_OPTIONS="-o nodatacow" triggers
this and 'btrfs check' errors out with:
[1/7] checking root items
[2/7] checking extents
[3/7] checking free space tree
[4/7] checking fs roots
root 256 inode 257 errors 1040, bad file extent, some csum missing
root 256 inode 258 errors 1040, bad file extent, some csum missing
ERROR: errors found in fs roots
(...)
So reject encoded writes if the target inode has NODATASUM set.
CC: stable@vger.kernel.org # 6.1+
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit feefe1f49d26bad9d8997096e3a200280fa7b1c5 upstream.
Currently when doing a write to a file we always reserve metadata space
for inserting data checksums. However we don't need to do it if we have
a nodatacow file (-o nodatacow mount option or chattr +C) or if checksums
are disabled (-o nodatasum mount option), as in that case we are only
adding unnecessary pressure to metadata reservations.
For example on x86_64, with the default node size of 16K, a 4K buffered
write into a nodatacow file is reserving 655360 bytes of metadata space,
as it's accounting for checksums. After this change, which stops reserving
space for checksums if we have a nodatacow file or checksums are disabled,
we only need to reserve 393216 bytes of metadata.
CC: stable@vger.kernel.org # 6.1+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
