IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 14ee78d5932afeb710c8305196a676a715bfdea8 upstream.
Add support for Sealevel 7xxxC serial cards.
This patch:
* Adds IDs to recognize 7xxxC cards from Sealevel Systems.
* Updates exar_pci_probe() to set nr_ports to last two bytes of primary
dev ID for these cards.
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2301191440010.22558@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5bfdd3c654bd879bff50c2e85e42f85ae698b42f upstream.
Commit ba47f97a18f2 ("serial: core: remove baud_rates when serial console
setup") changed uart_set_options to select the correct baudrate
configuration based on the absolute error between requested baudrate and
available standard baudrate settings.
Prior to that commit the baudrate was selected based on which predefined
standard baudrate did not exceed the requested baudrate.
This change of selection logic was never reflected in the atmel serial
driver. Thus the comment left in the atmel serial driver is no longer
accurate.
Additionally the manual rounding up described in that comment and applied
via (quot - 1) requests an incorrect baudrate. Since uart_set_options uses
tty_termios_encode_baud_rate to determine the appropriate baudrate flags
this can cause baudrate selection to fail entirely because
tty_termios_encode_baud_rate will only select a baudrate if relative error
between requested and selected baudrate does not exceed +/-2%.
Fix that by requesting actual, exact baudrate used by the serial.
Fixes: ba47f97a18f2 ("serial: core: remove baud_rates when serial console setup")
Cc: stable <stable@kernel.org>
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20230109072940.202936-1-t.schramm@manjaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f39aca2360c82dccd2f5179d77e94aab665bea6 upstream.
In RS485 mode the transmission of a high priority character fails since it
is written to the data register before the transmitter is enabled. Fix this
in pl011_tx_chars() by enabling RS485 transmission before writing the
character.
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20230108181735.10937-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8914b52e5b024e4af3d810a935fe0805eee8a36 upstream.
A local variable sg is used to store scatterlist pointer in
pch_dma_tx_complete(). The for loop doing Tx byte accounting before
dma_unmap_sg() alters sg in its increment statement. Therefore, the
pointer passed into dma_unmap_sg() won't match to the one given to
dma_map_sg().
To fix the problem, use priv->sg_tx_p directly in dma_unmap_sg()
instead of the local variable.
Fixes: da3564ee027e ("pch_uart: add multi-scatter processing")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230103093435.4396-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b8caf69a6946e18ffebad49847e258f5b6d52ac2 upstream.
Driver's probe allocates memory for RX FIFO (port->rx_fifo) based on
default RX FIFO depth, e.g. 16. Later during serial startup the
qcom_geni_serial_port_setup() updates the RX FIFO depth
(port->rx_fifo_depth) to match real device capabilities, e.g. to 32.
The RX UART handle code will read "port->rx_fifo_depth" number of words
into "port->rx_fifo" buffer, thus exceeding the bounds. This can be
observed in certain configurations with Qualcomm Bluetooth HCI UART
device and KASAN:
Bluetooth: hci0: QCA Product ID :0x00000010
Bluetooth: hci0: QCA SOC Version :0x400a0200
Bluetooth: hci0: QCA ROM Version :0x00000200
Bluetooth: hci0: QCA Patch Version:0x00000d2b
Bluetooth: hci0: QCA controller version 0x02000200
Bluetooth: hci0: QCA Downloading qca/htbtfw20.tlv
bluetooth hci0: Direct firmware load for qca/htbtfw20.tlv failed with error -2
Bluetooth: hci0: QCA Failed to request file: qca/htbtfw20.tlv (-2)
Bluetooth: hci0: QCA Failed to download patch (-2)
==================================================================
BUG: KASAN: slab-out-of-bounds in handle_rx_uart+0xa8/0x18c
Write of size 4 at addr ffff279347d578c0 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.1.0-rt5-00350-gb2450b7e00be-dirty #26
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xe0/0xf0
show_stack+0x18/0x40
dump_stack_lvl+0x8c/0xb8
print_report+0x188/0x488
kasan_report+0xb4/0x100
__asan_store4+0x80/0xa4
handle_rx_uart+0xa8/0x18c
qcom_geni_serial_handle_rx+0x84/0x9c
qcom_geni_serial_isr+0x24c/0x760
__handle_irq_event_percpu+0x108/0x500
handle_irq_event+0x6c/0x110
handle_fasteoi_irq+0x138/0x2cc
generic_handle_domain_irq+0x48/0x64
If the RX FIFO depth changes after probe, be sure to resize the buffer.
Fixes: f9d690b6ece7 ("tty: serial: qcom_geni_serial: Allocate port->rx_fifo buffer in probe")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221221164022.1087814-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2cbafffbf69addd7509072f4be5917f81d238cf6 upstream.
This reverts commit f24771b62a83239f0dce816bddf0f6807f436235 as it is
reported to break the build.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/202301200130.ttBiTzfO-lkp@intel.com
Fixes: f24771b62a83 ("serial: stm32: Merge hard IRQ and threaded IRQ handling into single IRQ handler")
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Valentin Caron <valentin.caron@foss.st.com> # V3
Cc: Marek Vasut <marex@denx.de>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f24771b62a83239f0dce816bddf0f6807f436235 upstream.
Requesting an interrupt with IRQF_ONESHOT will run the primary handler
in the hard-IRQ context even in the force-threaded mode. The
force-threaded mode is used by PREEMPT_RT in order to avoid acquiring
sleeping locks (spinlock_t) in hard-IRQ context. This combination
makes it impossible and leads to "sleeping while atomic" warnings.
Use one interrupt handler for both handlers (primary and secondary)
and drop the IRQF_ONESHOT flag which is not needed.
Fixes: e359b4411c283 ("serial: stm32: fix threaded interrupt handling")
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Valentin Caron <valentin.caron@foss.st.com> # V3
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230112180417.25595-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c0dccad87cf68fc6012aec7567e354353097ec1a ]
The currently lockless access to the xen console list in
vtermno_to_xencons() is incorrect, as additions and removals from the
list can happen anytime, and as such the traversal of the list to get
the private console data for a given termno needs to happen with the
lock held. Note users that modify the list already do so with the
lock taken.
Adjust current lock takers to use the _irq{save,restore} helpers,
since the context in which vtermno_to_xencons() is called can have
interrupts disabled. Use the _irq{save,restore} set of helpers to
switch the current callers to disable interrupts in the locked region.
I haven't checked if existing users could instead use the _irq
variant, as I think it's safer to use _irq{save,restore} upfront.
While there switch from using list_for_each_entry_safe to
list_for_each_entry: the current entry cursor won't be removed as
part of the code in the loop body, so using the _safe variant is
pointless.
Fixes: 02e19f9c7cac ('hvc_xen: implement multiconsole support')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20221130163611.14686-1-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a6ec673fb627c26e2267ca0a03849f91dbd9b40 ]
The sunsab_init() returns the platform_driver_register() directly without
checking its return value, if platform_driver_register() failed, the
allocated sunsab_ports is leaked.
Fix by free sunsab_ports and set it to NULL when platform_driver_register()
failed.
Fixes: c4d37215a824 ("[SERIAL] sunsab: Convert to of_driver framework.")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221123061212.52593-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1307c5d33cce8a41dd77c2571e4df65a5b627feb ]
Since altera_uart_interrupt() may also be called from
a poll timer in "serving_softirq" context, use
spin_[lock_irqsave|unlock_irqrestore] variants, which
are appropriate for both softirq and hardware interrupt
contexts.
Fixes: 2f8b9c15cd88 ("altera_uart: Add support for polling mode (IRQ-less)")
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Link: https://lore.kernel.org/r/20221122200426.888349-1-gsomlo@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8be3a7bf773700534a6e8f87f6ed2ed111254be5 ]
As comment of pci_get_slot() says, it returns a pci_device with its
refcount increased. The caller must decrement the reference count by
calling pci_dev_put().
Since 'dma_dev' is only used to filter the channel in filter(), we can
call pci_dev_put() before exiting from pch_request_dma(). Add the
missing pci_dev_put() for the normal and error path.
Fixes: 3c6a483275f4 ("Serial: EG20T: add PCH_UART driver")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221122114559.27692-1-wangxiongfeng2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d114e9ff940ebad8e88267013bf96c605a6b336 ]
If dma_request_chan() returns a PROBE_DEFER error, clk_disable_unprepare()
will be called and USART clock will be disabled. But early console can be
still active on the same USART.
While moving dma_request_chan() before clk_prepare_enable(), the clock
won't be taken in case of a DMA PROBE_DEFER error, and so it doesn't need
to be disabled. Then USART is still clocked for early console.
Fixes: a7770a4bfcf4 ("serial: stm32: defer probe for dma devices")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20221118170602.1057863-1-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 032d5a71ed378ffc6a2d41a187d8488a4f9fe415 ]
Clearing the RX FIFO will cause data loss.
Copy the pl011_enabl_interrupts implementation, and remove the clear
interrupt and FIFO part of the code.
Fixes: 211565b10099 ("serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle")
Signed-off-by: delisun <delisun@pateo.com.cn>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221110020108.7700-1-delisun@pateo.com.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94cdb9f33698478b0e7062586633c42c6158a786 ]
Chapter "B Generic UART" in "ARM Server Base System Architecture" [1]
documentation describes a generic UART interface. Such generic UART
does not support DMA. In current code, sbsa_uart_pops and
amba_pl011_pops share the same stop_rx operation, which will invoke
pl011_dma_rx_stop, leading to an access of the DMACR register. This
commit adds a using_rx_dma check in pl011_dma_rx_stop to avoid the
access to DMACR register for SBSA UARTs which does not support DMA.
When the kernel enables DMA engine with "CONFIG_DMA_ENGINE=y", Linux
SBSA PL011 driver will access PL011 DMACR register in some functions.
For most real SBSA Pl011 hardware implementations, the DMACR write
behaviour will be ignored. So these DMACR operations will not cause
obvious problems. But for some virtual SBSA PL011 hardware, like Xen
virtual SBSA PL011 (vpl011) device, the behaviour might be different.
Xen vpl011 emulation will inject a data abort to guest, when guest is
accessing an unimplemented UART register. As Xen VPL011 is SBSA
compatible, it will not implement DMACR register. So when Linux SBSA
PL011 driver access DMACR register, it will get an unhandled data abort
fault and the application will get a segmentation fault:
Unhandled fault at 0xffffffc00944d048
Mem abort info:
ESR = 0x96000000
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x00: ttbr address size fault
Data abort info:
ISV = 0, ISS = 0x00000000
CM = 0, WnR = 0
swapper pgtable: 4k pages, 39-bit VAs, pgdp=0000000020e2e000
[ffffffc00944d048] pgd=100000003ffff803, p4d=100000003ffff803, pud=100000003ffff803, pmd=100000003fffa803, pte=006800009c090f13
Internal error: ttbr address size fault: 96000000 [#1] PREEMPT SMP
...
Call trace:
pl011_stop_rx+0x70/0x80
tty_port_shutdown+0x7c/0xb4
tty_port_close+0x60/0xcc
uart_close+0x34/0x8c
tty_release+0x144/0x4c0
__fput+0x78/0x220
____fput+0x1c/0x30
task_work_run+0x88/0xc0
do_notify_resume+0x8d0/0x123c
el0_svc+0xa8/0xc0
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x1a0/0x1a4
Code: b9000083 b901f001 794038a0 8b000042 (b9000041)
---[ end trace 83dd93df15c3216f ]---
note: bootlogd[132] exited with preempt_count 1
/etc/rcS.d/S07bootlogd: line 47: 132 Segmentation fault start-stop-daemon
This has been discussed in the Xen community, and we think it should fix
this in Linux. See [2] for more information.
[1] https://developer.arm.com/documentation/den0094/c/?lang=en
[2] https://lists.xenproject.org/archives/html/xen-devel/2022-11/msg00543.html
Fixes: 0dd1e247fd39 (drivers: PL011: add support for the ARM SBSA generic UART)
Signed-off-by: Jiamei Xie <jiamei.xie@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20221117103237.86856-1-jiamei.xie@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a3ff858915fa8ca36c7eb02c87c9181ae2fc333 ]
A problem about 8250_bcm7271 create debugfs failed is triggered with the
following log given:
[ 324.516635] debugfs: Directory 'bcm7271-uart' with parent '/' already present!
The reason is that brcmuart_init() returns platform_driver_register()
directly without checking its return value, if platform_driver_register()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of 8250_bcm7271 can never be created later.
brcmuart_init()
debugfs_create_dir() # create debugfs directory
platform_driver_register()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when platform_driver_register() returns error.
Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221109072110.117291-2-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 109a951a9f1fd8a34ebd1896cbbd5d5cede880a7 ]
Read the DMA status before terminating the DMA, as doing so deletes
the DMA desc.
Also, to get the correct transfer status information, pause the DMA
using dmaengine_pause() before reading the DMA status.
Fixes: e9ea096dd225 ("serial: tegra: add serial driver")
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Link: https://lore.kernel.org/r/1666105086-17326-1-git-send-email-kkartik@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Here are a number of small tty and serial driver fixes for 6.1-rc6.
They all resolve reported problems:
- kernel doc build problems with the -rc1 serial driver
documentation update
- n_gsm reported problems
- imx serial driver missing callback
- lots of tiny 8250 driver fixes for reported issues.
All of these have been in linux-next for over a week with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY3fJoQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynycACgozhFjiUOjim8J0qUR943mlhTp/kAn0BVsKSk
PD8gi6Wk5SAybCpHxpsD
=Bqke
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for 6.1-rc6.
They all resolve reported problems:
- kernel doc build problems with the -rc1 serial driver documentation
update
- n_gsm reported problems
- imx serial driver missing callback
- lots of tiny 8250 driver fixes for reported issues.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'tty-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
docs/driver-api/miscellaneous: Remove kernel-doc of serial_core.c
serial: 8250: Flush DMA Rx on RLSI
serial: 8250_lpss: Use 16B DMA burst with Elkhart Lake
serial: 8250_lpss: Configure DMA also w/o DMA filter
serial: 8250: Fall back to non-DMA Rx if IIR_RDI occurs
tty: n_gsm: fix sleep-in-atomic-context bug in gsm_control_send
Revert "tty: n_gsm: replace kicktimer with delayed_work"
Revert "tty: n_gsm: avoid call of sleeping functions from atomic context"
serial: imx: Add missing .thaw_noirq hook
tty: serial: fsl_lpuart: don't break the on-going transfer when global reset
serial: 8250: omap: Flush PM QOS work on remove
serial: 8250: omap: Fix unpaired pm_runtime_put_sync() in omap8250_remove()
serial: 8250_omap: remove wait loop from Errata i202 workaround
serial: 8250: omap: Fix missing PM runtime calls for omap8250_set_mctrl()
serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
Returning true from handle_rx_dma() without flushing DMA first creates
a data ordering hazard. If DMA Rx has handled any character at the
point when RLSI occurs, the non-DMA path handles any pending characters
jumping them ahead of those characters that are pending under DMA.
Fixes: 75df022b5f89 ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure DMA to use 16B burst size with Elkhart Lake. This makes the
bus use more efficient and works around an issue which occurs with the
previously used 1B.
The fix was initially developed by Srikanth Thokala and Aman Kumar.
This together with the previous config change is the cleaned up version
of the original fix.
Fixes: 0a9410b981e9 ("serial: 8250_lpss: Enable DMA on Intel Elkhart Lake")
Cc: <stable@vger.kernel.org> # serial: 8250_lpss: Configure DMA also w/o DMA filter
Reported-by: Wentong Wu <wentong.wu@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform doesn't use DMA device filter (as is the case with
Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This
results in skipping also *_maxburst setup which is undesirable.
Refactor lpss8250_dma_setup() to configure DMA even if filter is not
setup.
Cc: stable <stable@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT
should have been triggered instead. Since IIR_RDI has higher priority
than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop.
The problem seems to occur at least with some combinations of
small-sized transfers (I've reproduced the problem on Elkhart Lake PSE
UARTs).
If there's already an on-going Rx DMA and IIR_RDI triggers, fall
graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had
occurred.
8250_omap already considers IIR_RDI similar to this change so its
nothing unheard of.
Fixes: 75df022b5f89 ("serial: 8250_dma: Fix RX handling")
Cc: <stable@vger.kernel.org>
Co-developed-by: Srikanth Thokala <srikanth.thokala@intel.com>
Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com>
Co-developed-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Aman Kumar <aman.kumar@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221108121952.5497-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
gsm_dlci_t1()
gsm_dlci_open()
gsm_modem_update()
gsm_modem_upd_via_msc()
gsm_control_send()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20221002040709.27849-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c9ab053e56ce13a949977398c8edc12e6c02fc95.
The above commit is reverted as it was a prerequisite for tx_mutex
introduction and tx_mutex has been removed as it does not correctly
work in order to protect tx data.
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221008110221.13645-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 902e02ea9385373ce4b142576eef41c642703955.
The above commit is reverted as the usage of tx_mutex seems not to solve
the problem described in 902e02ea9385 ("tty: n_gsm: avoid call of sleeping
functions from atomic context") and just moves the bug to another place.
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221008110221.13645-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lpuart_global_reset() shouldn't break the on-going transmit engine, need
to recover the on-going data transfer after reset.
This can help earlycon here, since commit 60f361722ad2 ("serial:
fsl_lpuart: Reset prior to registration") moved lpuart_global_reset()
before uart_add_one_port(), earlycon is writing during global reset,
as global reset will disable the TX and clear the baud rate register,
which caused the earlycon cannot work any more after reset, needs to
restore the baud rate and re-enable the transmitter to recover the
earlycon write.
Also move the lpuart_global_reset() down, then we can reuse the
lpuart32_tx_empty() without declaration.
Fixes: bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221024085844.22786-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221028110044.54719-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On remove, we get an error for "Runtime PM usage count underflow!". I guess
this driver is mostly built-in, and this issue has gone unnoticed for a
while. Somehow I did not catch this issue with my earlier fix done with
commit 4e0f5cc65098 ("serial: 8250_omap: Fix probe and remove for PM
runtime").
Fixes: 4e0f5cc65098 ("serial: 8250_omap: Fix probe and remove for PM runtime")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221028105813.54290-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20221013112339.2540767-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are cases where omap8250_set_mctrl() may get called after the
UART has already autoidled causing an asynchronous external abort.
This can happen on ttyport_open():
mem_serial_in from omap8250_set_mctrl+0x38/0xa0
omap8250_set_mctrl from uart_update_mctrl+0x4c/0x58
uart_update_mctrl from uart_dtr_rts+0x60/0xa8
uart_dtr_rts from tty_port_block_til_ready+0xd0/0x2a8
tty_port_block_til_ready from uart_open+0x14/0x1c
uart_open from ttyport_open+0x64/0x148
And on ttyport_close():
omap8250_set_mctrl from uart_update_mctrl+0x3c/0x48
uart_update_mctrl from uart_dtr_rts+0x54/0x9c
uart_dtr_rts from tty_port_shutdown+0x78/0x9c
tty_port_shutdown from tty_port_close+0x3c/0x74
tty_port_close from ttyport_close+0x40/0x58
It can also happen on disassociate_ctty() calling uart_shutdown()
that ends up calling omap8250_set_mctrl().
Let's fix the issue by adding missing PM runtime calls to
omap8250_set_mctrl(). To do this, we need to add __omap8250_set_mctrl()
that can be called from both omap8250_set_mctrl(), and from runtime PM
resume path when restoring the registers.
Fixes: 61929cf0169d ("tty: serial: Add 8250-core based omap driver")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Reported-by: Romain Naour <romain.naour@smile.fr>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Link: https://lore.kernel.org/r/20221024063613.25943-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity
exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(),
sets the TCRTLR bit in the MCR register and clears all other bits,
including RTS. If RTS uses active-low polarity, it is now asserted
for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR
register. That variable is always zero, so the RTS bit is still cleared
(incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's
current value. Rather, it only caches a single bit of that register,
the AFE bit. And it only does so if the UART supports the AFE bit,
which OMAP does not. For details see serial8250_do_set_termios() and
serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is
restored (and RTS deasserted) by a call to up->port.ops->set_mctrl()
(which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling
serial8250_em485_stop_tx(). Avoid by using a read-modify-write
when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained
above, the variable isn't used by the driver and it is already
initialized to zero because it is part of the static struct
serial8250_ports[] declared in 8250_core.c. (Static structs are
initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Su Bao Cheng <baocheng.su@siemens.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/6554b0241a2c7fd50f32576fdbafed96709e11e8.1664278942.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file name of this driver is misleading - it handles various serial
ports on parisc machines, not just such on the GSC bus.
Rename the file to make this clearer.
Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
* Convert the PDC console to an early console
* Unbreak mmap() of graphics card memory due to PAGE_SPECIAL pgtable flag
* Reduce the size of the alternative tables
* Align stifb graphics card memory size to 4MB
* Spelling fixes
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCY0mnYAAKCRD3ErUQojoP
X1z3AQC204Pq725WM3rgEomIqFjk8QaU2UFcNQ74a52V3AUiiQD8C0DFmWDbssUv
ZE5uC+ySlNd1hLkL3QYxrbbwuL+y+Q0=
=YvFZ
-----END PGP SIGNATURE-----
Merge tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Fixes:
- When we added basic vDSO support in kernel 5.18 we introduced a bug
which prevented a mmap() of graphic card memory. This is because we
used the DMB (data memory break trap bit) page flag as special-bit,
but missed to clear that bit when loading the TLB.
- Graphics card memory size was not correctly aligned
- Spelling fixes (from Colin Ian King)
Enhancements:
- PDC console (which uses firmware calls) now rewritten as early
console
- Reduced size of alternative tables"
* tag 'parisc-for-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix spelling mistake "mis-match" -> "mismatch" in eisa driver
parisc: Fix userspace graphics card breakage due to pgtable special bit
parisc: fbdev/stifb: Align graphics memory size to 4MB
parisc: Convert PDC console to an early console
parisc: Reduce kernel size by packing alternative tables
Rewrite the PDC console to become an early console.
Beside the fact that now boot information is visible until another
(text- or graphics) console takes over, this benefits as well machines
with a yet-unsupported STI console and kgdb.
Signed-off-by: Helge Deller <deller@gmx.de>
Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to
finally get this work done
- tty serial transmit cleanups in various drivers in preparation
for more cleanup and unification in future releases (that work
was not ready for this release.)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BSdA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylucQCfaXIrYuh2AHcb6+G+Nqp1xD2BYaEAoIdLyOCA
a2yziLrDF6us2oav6j4x
=Wv+X
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to finally get
this work done
- tty serial transmit cleanups in various drivers in preparation for
more cleanup and unification in future releases (that work was not
ready for this release)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full details in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (102 commits)
serial: cpm_uart: Don't request IRQ too early for console port
tty: serial: do unlock on a common path in altera_jtaguart_console_putc()
tty: serial: unify TX space reads under altera_jtaguart_tx_space()
tty: serial: use FIELD_GET() in lqasc_tx_ready()
tty: serial: extend lqasc_tx_ready() to lqasc_console_putchar()
tty: serial: allow pxa.c to be COMPILE_TESTed
serial: stm32: Fix unused-variable warning
tty: serial: atmel: Add COMMON_CLK dependency to SERIAL_ATMEL
serial: 8250: Fix restoring termios speed after suspend
serial: Deassert Transmit Enable on probe in driver-specific way
serial: 8250_dma: Convert to use uart_xmit_advance()
serial: 8250_omap: Convert to use uart_xmit_advance()
MAINTAINERS: Solve warning regarding inexistent atmel-usart binding
serial: stm32: Deassert Transmit Enable on ->rs485_config()
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
tty: serial: atmel: Use FIELD_PREP/FIELD_GET
tty: serial: atmel: Make the driver aware of the existence of GCLK
tty: serial: atmel: Only divide Clock Divisor if the IP is USART
tty: serial: atmel: Separate mode clearing between UART and USART
dt-bindings: serial: atmel,at91-usart: Add gclk as a possible USART clock
...
The main changes this time are for the organization of the Kconfig
files, introducing per-vendor top-level options on arm64 to match
those on arm32, and making the platform selection on arm32 more
uniform, in particular for the remaining StrongARM platforms that
still have a couple of special cases compared to the more recent
ones.
I also did a cleanup of the old Footbridge platform, which was
the last holdout for the phys_to_dma()/dma_to_phys() interface
that is now completely gone from arm32, completing work started
by Christoph Hellwig.
-----BEGIN PGP SIGNATURE-----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=xsKV
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The main changes this time are for the organization of the Kconfig
files, introducing per-vendor top-level options on arm64 to match
those on arm32, and making the platform selection on arm32 more
uniform, in particular for the remaining StrongARM platforms that
still have a couple of special cases compared to the more recent ones.
I also did a cleanup of the old Footbridge platform, which was the
last holdout for the phys_to_dma()/dma_to_phys() interface that is now
completely gone from arm32, completing work started by Christoph
Hellwig"
* tag 'arm-soc-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
ARM: aspeed: Kconfig: Fix indentation
ARM: Drop CMDLINE_* dependency on ATAGS
ARM: Drop CMDLINE_FORCE dependency on !ARCH_MULTIPLATFORM
ARM: s3c: remove orphan declarations from arch/arm/mach-s3c/devs.h
pxa: Drop if with an always false condition
ARM: orion: fix include path
ARM: shmobile: Drop selecting SOC_BUS
arm64: renesas: Drop selecting SOC_BUS
ARM: disallow PCI with MMU=n again
ARM: footbridge: remove custom DMA address handling
MAINTAINERS: Add BCM4908 maintainer to BCMBCA entry
ARM: footbridge: move isa-dma support into footbridge
ARM: footbridge: remove leftover from personal-server
ARM: footbridge: remove addin mode
arm64: Kconfig.platforms: Group NXP platforms together
arm64: Kconfig.platforms: Re-organized Broadcom menu
ARM: make ARCH_MULTIPLATFORM user-visible
ARM: fix XIP_KERNEL dependencies
ARM: Kconfig: clean up platform selection
ARM: simplify machdirs/platdirs handling
...
The drivers branch for 6.1 is a bit larger than for most releases. Most
of the changes come from SoC maintainers for the drivers/soc subsystem:
- A new driver for error handling on the NVIDIA Tegra
'control backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip
SoCs, various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM
driver, the Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas,
Tegra, Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers that
merge updates this way:
- Various updates and new drivers in the memory controller
subsystem for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A
v1.1 specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmM+j54ACgkQmmx57+YA
GNkK1Q//fSzCHUPNTrZKJi8mRtp/32Nrpav3eorMZWltKnYbYQyhqH/LCuSZJfe/
rmGYFxsH6DHEgfHqqyzm6PNC0S4Hle6KiB5xnqXrTgqciPuSg4Fa9OMQgkbiQF6x
uB2KR+TouQA3MssQh6NW4wy5XAkEqudZCSnEyOTJTmdpepZd/1Eu2Rhn8kx5AYQN
pzYNGURRoirgYbO9vHMssCcpqyGNdR9SWXcOkROyd65L4LCHQ9JRh4etg7fSXP5j
abWtTHSOwD8MTXOENOiNw/vyCfBX7wUoJkY2v8OUo3G/20qbOXKWPWi056gyDjVQ
kJdlnnK4APtiluyBg2alEEZmJOd1iCaVP2j84EO1N4FEek2UGd/lMNOtAOJa+wbh
eiE6KC5gswe+99//PdY4gB+7dRM3I0gU7FDMl9G5A4DPMEE/0bMKLKk1jR5vyYXl
6QpN2N0OlU7d16MJiP9RvWf2/xJrcQrLQcy8FKvFVWClJ9wMvBXozKrvXgji9l3I
ZTW+EViQiyWmj6KbFlDZkYT+Q6YosxaogJUNrZeIaAwmwJj1oTa+M6jYRnFU6uha
XxG5TrybC9JQ/BpYCTYEqb16LOYALwEm7NWmylWASUCCZclC1u35qmmVEhDyBcS9
98ePumkAwrcjmW0TZsiYXOCQWNOITuvU/Ku2t/+6Mhg+Xl44zX4=
=WX9J
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"The drivers branch for 6.1 is a bit larger than for most releases.
Most of the changes come from SoC maintainers for the drivers/soc
subsystem:
- A new driver for error handling on the NVIDIA Tegra 'control
backbone' bus.
- A new driver for Qualcomm LLCC/DDR bandwidth measurement
- New Rockchip rv1126 and rk3588 power domain drivers
- DT binding updates for memory controllers, older Rockchip SoCs,
various Mediatek devices, Qualcomm SCM firmware
- Minor updates to Hisilicon LPC bus, the Allwinner SRAM driver, the
Apple rtkit firmware driver, Tegra firmware
- Minor updates for SoC drivers (Samsung, Mediatek, Renesas, Tegra,
Qualcomm, Broadcom, NXP, ...)
There are also some separate subsystem with downstream maintainers
that merge updates this way:
- Various updates and new drivers in the memory controller subsystem
for Mediatek and Broadcom SoCs
- Small set of changes in preparation to add support for FF-A v1.1
specification later, in the Arm FF-A firmware subsystem
- debugfs support in the PSCI firmware subsystem"
* tag 'arm-drivers-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (149 commits)
ARM: remove check for CONFIG_DEBUG_LL_SER3
firmware/psci: Add debugfs support to ease debugging
firmware/psci: Print a warning if PSCI doesn't accept PC mode
dt-bindings: memory: snps,dw-umctl2-ddrc: Extend schema with IRQs/resets/clocks props
dt-bindings: memory: snps,dw-umctl2-ddrc: Replace opencoded numbers with macros
dt-bindings: memory: snps,dw-umctl2-ddrc: Use more descriptive device name
dt-bindings: memory: synopsys,ddrc-ecc: Detach Zynq DDRC controller support
soc: sunxi: sram: Add support for the D1 system control
soc: sunxi: sram: Export the LDO control register
soc: sunxi: sram: Save a pointer to the OF match data
soc: sunxi: sram: Return void from the release function
soc: apple: rtkit: Add apple_rtkit_poll
soc: imx: add i.MX93 media blk ctrl driver
soc: imx: add i.MX93 SRC power domain driver
soc: imx: imx8m-blk-ctrl: Use genpd_xlate_onecell
soc: imx: imx8mp-blk-ctrl: handle PCIe PHY resets
soc: imx: imx8m-blk-ctrl: add i.MX8MP VPU blk ctrl
soc: imx: add i.MX8MP HDMI blk ctrl HDCP/HRV_MWR
soc: imx: add icc paths for i.MX8MP hsio/hdmi blk ctrl
soc: imx: add icc paths for i.MX8MP media blk ctrl
...
The following message is seen during boot and the activation of
console port gets delayed until normal serial ports activation.
[ 0.001346] irq: no irq domain found for pic@930 !
The console port doesn't need irq, perform irq reservation later,
during cpm_uart probe.
While at it, don't use NO_IRQ but 0 which is the value returned
by irq_of_parse_and_map() in case of error. By chance powerpc's
NO_IRQ has value 0 but on some architectures it is -1.
Fixes: 14d893fc6846 ("powerpc/8xx: Convert CPM1 interrupt controller to platform_device")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/8bed0f30c2e9ef16ae64fb1243a16d54a48eb8da.1664526717.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
port->lock is unlocked in each branch in altera_jtaguart_console_putc(),
so do it before the "if". "status" needs not be under the lock, as the
register was already read.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220927111819.18516-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX space reads from the control register are performed in various forms
on 4 places in altera_jtaguart. Unify all those and do the read and
masking on a single place.
The new helper altera_jtaguart_tx_space() uses FIELD_GET(), so we can
drop ALTERA_JTAGUART_CONTROL_WSPACE_OFF now.
Cc: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Link: https://lore.kernel.org/r/20220927111819.18516-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FIELD_GET() can do the job smarter and more readable. We don't even need
ASCFSTAT_TXFREEOFF. So switch to the former and remove the latter.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220927111819.18516-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is one more place where lqasc_tx_ready() can be used now:
lqasc_console_putchar(). So replace the open-coded variant by the
helper.
Suggested-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220927111819.18516-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no issue compiling pxa.c even in the SERIAL_8250=y case. So to
cover it in the usual configurations, add "|| COMPILE_TEST" there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220927110528.12815-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_SERIAL_EARLYCON and CONFIG_OF are both not set,
gcc warns about unused variable:
drivers/tty/serial/stm32-usart.c:83:32: error: ‘stm32h7_info’ defined but not used [-Werror=unused-variable]
static struct stm32_usart_info stm32h7_info = {
^~~~~~~~~~~~
drivers/tty/serial/stm32-usart.c:61:32: error: ‘stm32f7_info’ defined but not used [-Werror=unused-variable]
static struct stm32_usart_info stm32f7_info = {
^~~~~~~~~~~~
drivers/tty/serial/stm32-usart.c:40:32: error: ‘stm32f4_info’ defined but not used [-Werror=unused-variable]
static struct stm32_usart_info stm32f4_info = {
^~~~~~~~~~~~
cc1: all warnings being treated as errors
Mark these variables as __maybe_unused to fix this.
Fixes: c7039ce904c0 ("serial: stm32: make info structs static to avoid sparse warnings")
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Link: https://lore.kernel.org/r/20220926025826.44145-1-renzhijie2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver makes use of `__clk_is_enabled()` in order to
know whether a `clk_disable_unprepare()` is needed or not on the
GCLK, a new dependency has been introduced: COMMON_CLK. If this
`CONFIG_COMMON_CLK` is not enabled, whatever config may have this
driver enabled without COMMON_CLK then an undefined reference to
`__clk_is_enabled()` will be issued by the linker.
Thus, make sure that, unless `CONFIG_COMMON_CLK` is enabled, this
driver is not compiled.
Fixes: 5e3ce1f26129 ("tty: serial: atmel: Make the driver aware of the existence of GCLK")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220926143244.485578-1-sergiu.moga@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Since commit 027b57170bf8 ("serial: core: Fix initializing and restoring
termios speed") termios speed is available also in struct console.
So properly restore also c_ispeed and c_ospeed members after suspend to fix
restoring termios speed which is not represented by Bnnn constant.
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220924104324.4035-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_xmit_advance() provides a common way on how to advance
the Tx queue. Use it for the sake of unification and robustness.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220909091102.58941-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
