IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 95d7c452a26564ef0c427f2806761b857106d8c4 ]
The dev_warn to notify about a spurious interrupt was introduced with
the reasoning that these are unexpected. However spurious interrupts
tend to trigger continously and the error message on the serial console
prevents that the core's detection of spurious interrupts kicks in
(which disables the irq) and just floods the console.
Fixes: c64e7efe46b7 ("spi: stm32: make spurious and overrun interrupts visible")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://msgid.link/r/20240521105241.62400-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f788ba457b45b0ce422943fcec9fa35c4587764 ]
There is no need to set the DMA mapped flag of the message if it has
no mapped transfers. Moreover, it may give the code a chance to take
the wrong paths, i.e. to exercise DMA related APIs on unmapped data.
Make __spi_map_msg() to bail earlier on the above mentioned cases.
Fixes: 99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://msgid.link/r/20240522171018.3362521-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ef13561d2b163ac0ae6befa53bca58a26dc3320b upstream.
Before ORing the new clock rate with the control register value read
from the hardware, the existing clock rate needs to be masked off as
otherwise the existing value will interfere with the new one.
CC: stable@vger.kernel.org
Fixes: 8596124c4c1b ("spi: microchip-core-qspi: Add support for microchip fpga qspi controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240508-fox-unpiloted-b97e1535627b@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4756fa529b2f12b7cb8f21fe229b0f6f47190829 ]
If spi_sync() is called with the non-empty queue and the same spi_message
is then reused, the complete callback for the message remains set while
the context is cleared, leading to a null pointer dereference when the
callback is invoked from spi_finalize_current_message().
With function inlining disabled, the call stack might look like this:
_raw_spin_lock_irqsave from complete_with_flags+0x18/0x58
complete_with_flags from spi_complete+0x8/0xc
spi_complete from spi_finalize_current_message+0xec/0x184
spi_finalize_current_message from spi_transfer_one_message+0x2a8/0x474
spi_transfer_one_message from __spi_pump_transfer_message+0x104/0x230
__spi_pump_transfer_message from __spi_transfer_message_noqueue+0x30/0xc4
__spi_transfer_message_noqueue from __spi_sync+0x204/0x248
__spi_sync from spi_sync+0x24/0x3c
spi_sync from mcp251xfd_regmap_crc_read+0x124/0x28c [mcp251xfd]
mcp251xfd_regmap_crc_read [mcp251xfd] from _regmap_raw_read+0xf8/0x154
_regmap_raw_read from _regmap_bus_read+0x44/0x70
_regmap_bus_read from _regmap_read+0x60/0xd8
_regmap_read from regmap_read+0x3c/0x5c
regmap_read from mcp251xfd_alloc_can_err_skb+0x1c/0x54 [mcp251xfd]
mcp251xfd_alloc_can_err_skb [mcp251xfd] from mcp251xfd_irq+0x194/0xe70 [mcp251xfd]
mcp251xfd_irq [mcp251xfd] from irq_thread_fn+0x1c/0x78
irq_thread_fn from irq_thread+0x118/0x1f4
irq_thread from kthread+0xd8/0xf4
kthread from ret_from_fork+0x14/0x28
Fix this by also setting message->complete to NULL when the transfer is
complete.
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/r/20240430182705.13019-1-mans@mansr.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7430764f5a85d30314aeef2d5438dff1fb0b1d68 ]
Due to the reading of FIFO during the dump of data registers in
debugfs, if SPI transmission is in progress, it will be affected
and may result in transmission failure. Therefore, the dump
interface of data registers in debugfs is removed.
Fixes: 2b2142f247eb ("spi: hisi-kunpeng: Add debugfs support")
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Reviewed-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/20240416015839.3323398-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0064db9ce4aa7cc794e6f4aed60dee0f94fc9bcf ]
The version format string in the AXI SPI Engine driver was probably
intended to print the version number in the same format as the DT
compatible string (e.g. 1.00.a). However, the version just uses
semantic versioning so formatting the patch number as a character
is not correct and would result in printing control characters for
patch numbers less than 32.
Fixes: b1353d1c1d45 ("spi: Add Analog Devices AXI SPI Engine controller support")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240412-axi-spi-engine-version-printf-v1-1-95e1e842c1a6@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 88c2b56c2690061121cad03f0f551db465287575 ]
This avoid duplicating the same macros in multiple drivers by reusing
the common AXI macros for the version register.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240202213132.3863124-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f970ecb77b6759d37ee743fc36fc0daba960e75 ]
This moves the message state in the AXI SPI Engine driver to a new
struct spi_engine_msg_state.
Previously, the driver state contained various pointers that pointed
to memory owned by a struct spi_message. However, it did not set any of
these pointers to NULL when a message was completed. This could lead to
use after free bugs.
Example of how this could happen:
1. SPI core calls into spi_engine_transfer_one_message() with msg1.
2. Assume something was misconfigured and spi_engine_tx_next() is not
called enough times in interrupt callbacks for msg1 such that
spi_engine->tx_xfer is never set to NULL before the msg1 completes.
3. SYNC interrupt is received and spi_finalize_current_message() is
called for msg1. spi_engine->msg is set to NULL but no other
message-specific state is reset.
4. Caller that sent msg1 is notified of the completion and frees msg1
and the associated xfers and tx/rx buffers.
4. SPI core calls into spi_engine_transfer_one_message() with msg2.
5. When spi_engine_tx_next() is called for msg2, spi_engine->tx_xfer is
still be pointing to an xfer from msg1, which was already freed.
spi_engine_xfer_next() tries to access xfer->transfer_list of one
of the freed xfers and we get a segfault or undefined behavior.
To avoid issues like this, instead of putting per-message state in the
driver state struct, we can make use of the struct spi_message::state
field to store a pointer to a new struct spi_engine_msg_state. This way,
all of the state that belongs to specific message stays with that
message and we don't have to remember to manually reset all aspects of
the message state when a message is completed. Rather, a new state is
allocated for each message.
Most of the changes are just renames where the state is accessed. One
place where this wasn't straightforward was the sync_id member. This
has been changed to use ida_alloc_range() since we needed to separate
the per-message sync_id from the per-controller next available sync_id.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231117-axi-spi-engine-series-1-v1-9-cc59db999b87@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e12cd96e8e93044646fdf4b2c9a1de62cfa01e7c ]
This modifies the AXI SPI Engine driver to use devm_spi_alloc_host()
instead of spi_alloc_host() to simplify the code a bit.
In addition to simplifying the error paths in the probe function, we
can also remove spi_controller_get/put() calls in the remove function
since devm_spi_alloc_host() sets a flag to no longer decrement the
controller reference count in the spi_unregister_controller() function.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231117-axi-spi-engine-series-1-v1-4-cc59db999b87@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e4ce5220eedea2cc440f3961dec1b5122e815b2 ]
This simplifies the private data allocation in the AXI SPI Engine driver
by making use of the feature built into the spi_alloc_host() function
instead of doing it manually.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231117-axi-spi-engine-series-1-v1-3-cc59db999b87@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a08199b309f833fd4221ab5ee2391c791fe26385 ]
Since commit 7ef9651e9792 ("clk: Provide new devm_clk helpers for prepared
and enabled clocks"), devm_clk_get() and clk_prepare_enable() can now be
replaced by devm_clk_get_enabled() when driver enables (and possibly
prepares) the clocks for the whole lifetime of the device. Moreover, it is
no longer necessary to unprepare and disable the clocks explicitly.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230823133938.1359106-6-lizetao1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d5920b37ab4a970f658a6a30b54cc6d6a7d2d3d ]
Change legacy name master to modern name host or controller.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230728093221.3312026-4-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc87abbef23413943457459e2c473ce607b4dd24 ]
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8d3b056a78dcc941fd1a117697ab2b956c2953f ]
For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
- step1: introduce new helpers with modern naming.
- step2: switch to use these new helpers in all drivers.
- step3: remove all legacy helpers and update all legacy names.
This patch is for step1, it introduces new helpers with host/target
naming for drivers using.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a20ad45008a7c82f1184dc6dee280096009ece55 ]
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it.
Fixes: 1ce24864bff4 ("spi: mediatek: Only do dma for 4-byte aligned buffers")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://msgid.link/r/20240321070942.1587146-2-fshao@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de8b6e1c231a95abf95ad097b993d34b31458ec9 ]
Return IRQ_NONE from the interrupt handler when no interrupt was
detected. Because an empty interrupt will cause a null pointer error:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
complete+0x54/0x100
hisi_sfc_v3xx_isr+0x2c/0x40 [spi_hisi_sfc_v3xx]
__handle_irq_event_percpu+0x64/0x1e0
handle_irq_event+0x7c/0x1cc
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Link: https://msgid.link/r/20240123071149.917678-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3aa619a8b4706f35cb62f780c14e68796b37f3f ]
Since commit 24778be20f87 ("spi: convert drivers to use
bits_per_word_mask") the bits_per_word variable is only written to. The
check that was there before isn't needed any more as the spi core
ensures that only 8 bit transfers are used, so the variable can go away
together with all assignments to it.
Fixes: 24778be20f87 ("spi: convert drivers to use bits_per_word_mask")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240210164006.208149-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c2ae772fe08e33f3d7a83849e85539320701abd ]
In __spi_pump_transfer_message(), the message was not finalized in the
first error return as it is in the other error return paths. Not
finalizing the message could cause anything waiting on the message to
complete to hang forever.
This adds the missing call to spi_finalize_current_message().
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://msgid.link/r/20240125205312.3458541-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 574bf7bbe83794a902679846770f75a9b7f28176 ]
SFDP read shall use the mspi reads when using the bcm_qspi_exec_mem_op()
call. This fixes SFDP parameter page read failures seen with parts that
now use SFDP protocol to read the basic flash parameter table.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://msgid.link/r/20240109210033.43249-1-kamal.dasu@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5c7bcb499840551cfbe85c6df177ebc50432bf0 ]
Documentation says only DTDL of 200 is allowed for this SoC.
Fixes: 4286db8456f4 ("spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://msgid.link/r/20231212081239.14254-1-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424a8166764e462258fdccaaefbdeb07517c8b21 ]
ZynqMP GQSPI driver no longer uses spi-master framework. It had been
converted to use spi-mem framework. So remove driver dependency from
spi-master and replace it with spi-mem.
Fixes: 1c26372e5aa9 ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699282435-884917-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc70d643a2f6678cbe0f5c86433c1aeb4d613fcc ]
The current Atmel SPI controller driver (v2) behaves incorrectly when
using two SPI devices with different clock polarities and GPIO CS.
When switching from one device to another, the controller driver first
enables the CS and then applies whatever configuration suits the targeted
device (typically, the polarities). The side effect of such order is the
apparition of a spurious clock edge after enabling the CS when the clock
polarity needs to be inverted wrt. the previous configuration of the
controller.
This parasitic clock edge is problematic when the SPI device uses that edge
for internal processing, which is perfectly legitimate given that its CS
was asserted. Indeed, devices such as HVS8080 driven by driver gpio-sr in
the kernel are shift registers and will process this first clock edge to
perform a first register shift. In this case, the first bit gets lost and
the whole data block that will later be read by the kernel is all shifted
by one.
Current behavior:
The actual switching of the clock polarity only occurs after the CS
when the controller sends the first message:
CLK ------------\ /-\ /-\
| | | | | . . .
\---/ \-/ \
CS -----\
|
\------------------
^ ^ ^
| | |
| | Actual clock of the message sent
| |
| Change of clock polarity, which occurs with the first
| write to the bus. This edge occurs when the CS is
| already asserted, and can be interpreted as
| the first clock edge by the receiver.
|
GPIO CS toggle
This issue is specific to this controller because while the SPI core
performs the operations in the right order, the controller however does
not. In practice, the controller only applies the clock configuration right
before the first transmission.
So this is not a problem when using the controller's dedicated CS, as the
controller does things correctly, but it becomes a problem when you need to
change the clock polarity and use an external GPIO for the CS.
One possible approach to solve this problem is to send a dummy message
before actually activating the CS, so that the controller applies the clock
polarity beforehand.
New behavior:
CLK ------\ /-\ /-\ /-\ /-\
| | | ... | | | | ... | |
\------/ \- -/ \------/ \- -/ \------
CS -\/-----------------------\
|| |
\/ \---------------------
^ ^ ^ ^ ^
| | | | |
| | | | Expected clock cycles when
| | | | sending the message
| | | |
| | | Actual GPIO CS activation, occurs inside
| | | the driver
| | |
| | Dummy message, to trigger clock polarity
| | reconfiguration. This message is not received and
| | processed by the device because CS is low.
| |
| Change of clock polarity, forced by the dummy message. This
| time, the edge is not detected by the receiver.
|
This small spike in CS activation is due to the fact that the
spi-core activates the CS gpio before calling the driver's
set_cs callback, which deactivates this gpio again until the
clock polarity is correct.
To avoid having to systematically send a dummy packet, the driver keeps
track of the clock's current polarity. In this way, it only sends the dummy
packet when necessary, ensuring that the clock will have the correct
polarity when the CS is toggled.
There could be two hardware problems with this patch:
1- Maybe the small CS activation peak can confuse SPI devices
2- If on a design, a single wire is used to select two devices depending
on its state, the dummy message may disturb them.
Fixes: 5ee36c989831 ("spi: atmel_spi update chipselect handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20231204154903.11607-1-louis.chauvet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 303feb3cc06ac0665d0ee9c1414941200e60e8a3 ]
Supporting multi-cs in spi core and spi controller drivers would require
the chip_select & cs_gpiod members of struct spi_device to be an array.
But changing the type of these members to array would break the spi driver
functionality. To make the transition smoother introduced four new APIs to
get/set the spi->chip_select & spi->cs_gpiod and replaced all
spi->chip_select and spi->cs_gpiod references in spi core with the API
calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119185342.2093323-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fc70d643a2f6 ("spi: atmel: Fix clock issue when using devices with different polarities")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 684a47847ae639689e7b823251975348a8e5434f ]
commit 4ccf359849ce ("spi: remove spi_set_cs_timing()"), removed the
method as noboby used it. Nobody used it probably because some SPI
controllers use some default large cs-setup time that covers the usual
cs-setup time required by the spi devices. There are though SPI controllers
that have a smaller granularity for the cs-setup time and their default
value can't fulfill the spi device requirements. That's the case for the
at91 QSPI IPs where the default cs-setup time is half of the QSPI clock
period. This was observed when using an sst26vf064b SPI NOR flash which
needs a spi-cs-setup-ns = <7>; in order to be operated close to its maximum
104 MHz frequency.
Call spi_set_cs_timing() in spi_setup() just before calling spi_set_cs(),
as the latter needs the CS timings already set.
If spi->controller->set_cs_timing is not set, the method will return 0.
There's no functional impact expected for the existing drivers. Even if the
spi-mt65xx.c and spi-tegra114.c drivers set the set_cs_timing method,
there's no user for them as of now. The only tested user of this support
will be a SPI NOR flash that comunicates with the Atmel QSPI controller for
which the support follows in the next patches.
One will notice that this support is a bit different from the one that was
removed in commit 4ccf359849ce ("spi: remove spi_set_cs_timing()"),
because this patch adapts to the changes done after the removal: the move
of the cs delays to the spi device, the retirement of the lelgacy GPIO
handling. The mutex handling was removed from spi_set_cs_timing() because
we now always call spi_set_cs_timing() in spi_setup(), which already
handles the spi->controller->io_mutex, so use the mutex handling from
spi_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-4-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: fc70d643a2f6 ("spi: atmel: Fix clock issue when using devices with different polarities")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aea672d054a21782ed8450c75febb6ba3c208ca4 ]
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: ee4d79055aee ("iio: imu: adis16475: add spi_device_id table")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bef4a48f4ef798c4feddf045d49e53c8a97d5e37 ]
A race condition exists where a synchronous (noqueue) transfer can be
active during a system suspend. This can cause a null pointer
dereference exception to occur when the system resumes.
Example order of events leading to the exception:
1. spi_sync() calls __spi_transfer_message_noqueue() which sets
ctlr->cur_msg
2. Spi transfer begins via spi_transfer_one_message()
3. System is suspended interrupting the transfer context
4. System is resumed
6. spi_controller_resume() calls spi_start_queue() which resets cur_msg
to NULL
7. Spi transfer context resumes and spi_finalize_current_message() is
called which dereferences cur_msg (which is now NULL)
Wait for synchronous transfers to complete before suspending by
acquiring the bus mutex and setting/checking a suspend flag.
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Link: https://lore.kernel.org/r/20231107144743.v1.1.I7987f05f61901f567f7661763646cb7d7919b528@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2ded280a4b1b7bd93e53670528504be08d24967 ]
Zynq QSPI driver has been converted to use spi-mem framework so
add spi-mem to driver kconfig dependencies.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1699037031-702858-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3aa5cb264a38ae9bbcce32abca4c155af0456df ]
AHB memory as MMIO should be mapped with ioremap rather than ioremap_wc,
which should have been used initially just to handle unaligned access as
a workaround.
Fixes: d166a73503ef ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20231010201524.2021340-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb9913b511f10968a02cfa5329a896855dd152a3 ]
This func misses checking for platform_get_irq()'s call and may passes the
negative error codes to request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Fix this by stop calling request_irq() with invalid IRQ #s.
Fixes: dc4dc3605639 ("spi: tegra: add spi driver for SLINK controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Link: https://lore.kernel.org/r/tencent_73FCC06A3D1C14EE5175253C6FB46A07B709@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ec8b010979036c2fe79a64adb6ecc0bd11e91d1 ]
We don't want to use the value of ilog2(0) as dummy.buswidth is 0 when
dummy.nbytes is 0. Since we have no dummy bytes, we don't need to
configure the dummy byte bits per clock register value anyway.
Signed-off-by: "William A. Kennington III" <william@wkennington.com>
Link: https://lore.kernel.org/r/20230922182812.2728066-1-william@wkennington.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1527b076ae2cb6a9c590a02725ed39399fcad1cf ]
Make sure that the device is not runtime suspended before explicitly
disabling the clocks on probe failure and on driver unbind to avoid a
clock enable-count imbalance.
Fixes: 9e3a000362ae ("spi: zynqmp: Add pm runtime support")
Cc: stable@vger.kernel.org # 4.19
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/Message-Id: <20230622082435.7873-1-johan+linaro@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9855d60cfc720ff32355484c119acafd3c4dc806 ]
Intel Granite Rapids has a flash controller that is compatible with the
other Cannon Lake derivatives. Add Granite Rapids PCI ID to the driver
list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230911074616.3473347-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18495676f7886e105133f1dc06c1d5e8d5436f32 ]
Reset the FLSHxCR1 registers to default value. ROM may set the register
value and it affects the SPI NAND normal functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20230906183254.235847-1-han.xu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f11f4202caf5710204d334fe63392052783876d ]
Previously the transfer complete IRQ immediately drained to RX FIFO to
read any data remaining in FIFO to the RX buffer. This behaviour is
correct when dealing with SPI in interrupt mode. However in DMA mode the
transfer complete interrupt still fires as soon as all bytes to be
transferred have been stored in the FIFO. At that point data in the FIFO
still needs to be picked up by the DMA engine. Thus the drain procedure
and DMA engine end up racing to read from RX FIFO, corrupting any data
read. Additionally the RX buffer pointer is never adjusted according to
DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA
mode is a bug.
Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode.
Also wait for completion of RX DMA when in DMA mode before returning to
ensure all data has been copied to the supplied memory buffer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20230827152558.5368-3-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 171f8a49f212e87a8b04087568e1b3d132e36a18 ]
Through empirical testing it has been determined that sometimes RX SPI
transfers with DMA enabled return corrupted data. This is down to single
or even multiple bytes lost during DMA transfer from SPI peripheral to
memory. It seems the RX FIFO within the SPI peripheral can become
confused when performing bus read accesses wider than a single byte to it
during an active SPI transfer.
This patch reduces the width of individual DMA read accesses to the
RX FIFO to a single byte to mitigate that issue.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20230827152558.5368-2-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a8196a93e493c0a50b800cb09cef60b124eee15 ]
Bug fix to correct return value of gxp_spi_write function to zero.
Completion of succesful operation should return zero.
Fixes: 730bc8ba5e9e spi: spi-gxp: Add support for HPE GXP SoCs
Signed-off-by: Charles Kearney <charles.kearney@hpe.com>
Link: https://lore.kernel.org/r/20230920215339.4125856-2-charles.kearney@hpe.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1a50d9403fb90cbe4dea0ec9fd0351d2ecbd8924 upstream.
When loading a DT overlay that creates a device, the device is not
probed, unless the DT overlay is unloaded and reloaded again.
After the recent refactoring to improve fw_devlink, it no longer depends
on the "compatible" property to identify which device tree nodes will
become struct devices. fw_devlink now picks up dangling consumers
(consumers pointing to descendent device tree nodes of a device that
aren't converted to child devices) when a device is successfully bound
to a driver. See __fw_devlink_pickup_dangling_consumers().
However, during DT overlay, a device's device tree node can have
sub-nodes added/removed without unbinding/rebinding the driver. This
difference in behavior between the normal device instantiation and
probing flow vs. the DT overlay flow has a bunch of implications that
are pointed out elsewhere[1]. One of them is that the fw_devlink logic
to pick up dangling consumers is never exercised.
This patch solves the fw_devlink issue by marking all DT nodes added by
DT overlays with FWNODE_FLAG_NOT_DEVICE (fwnode that won't become
device), and by clearing the flag when a struct device is actually
created for the DT node. This way, fw_devlink knows not to have
consumers waiting on these newly added DT nodes, and to propagate the
dependency to an ancestor DT node that has the corresponding struct
device.
Based on a patch by Saravana Kannan, which covered only platform and spi
devices.
[1] https://lore.kernel.org/r/CAGETcx_bkuFaLCiPrAWCPQz+w79ccDp6=9e881qmK=vx3hBMyg@mail.gmail.com
Fixes: 4a032827daa89350 ("of: property: Simplify of_link_to_phandle()")
Link: https://lore.kernel.org/r/CAGETcx_+rhHvaC_HJXGrr5_WAd2+k5f=rWYnkCZ6z5bGX-wj4w@mail.gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Saravana Kannan <saravanak@google.com>
Tested-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Link: https://lore.kernel.org/r/e1fa546682ea4c8474ff997ab6244c5e11b6f8bc.1680182615.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 29a449e765ff70a5bd533be94babb6d36985d096 ]
The platform_get_irq might be failed and return a negative result. So
there should have an error handling code.
Fixed this by adding an error handling code.
Fixes: 8528547bcc33 ("spi: tegra: add spi driver for sflash controller")
Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_71FC162D589E4788C2152AAC84CD8D5C6D06@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5b6d0b91f84cff3f28724076f93f6f9e2ef8d775 upstream.
Remove a misleading comment about the DMA operations of the Intel Mount
Evans SoC's SPI Controller as requested by Serge.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Link: https://lore.kernel.org/linux-spi/20230606191333.247ucbf7h3tlooxf@mobilestation/
Fixes: 0760d5d0e9f0 ("spi: dw: Add compatible for Intel Mount Evans SoC")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230606231844.726272-1-abe.kohandel@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ec3c5517e22a12d2ff1b71e844f7913641460c6 ]
When SPI loopback transfer is performed, S3C64XX_SPI_MODE_SELF_LOOPBACK
bit still remained. It works as loopback even if the next transfer is
not spi loopback mode.
If not SPI_LOOP, needs to clear S3C64XX_SPI_MODE_SELF_LOOPBACK bit.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Fixes: ffb7bcd3b27e ("spi: s3c64xx: support loopback mode")
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20230711082020.138165-1-jaewon02.kim@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5158814cbb37bbb38344b3ecddc24ba2ed0365f2 ]
The command word is defined as following:
/* Command */
#define SPI_CMD_COMMAND_SHIFT 0
#define SPI_CMD_DEVICE_ID_SHIFT 4
#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
#define SPI_CMD_ONE_BYTE_SHIFT 11
#define SPI_CMD_ONE_WIRE_SHIFT 12
If the prepend byte count field starts at bit 8, and the next defined
bit is SPI_CMD_ONE_BYTE at bit 11, it can be at most 3 bits wide, and
thus the max value is 7, not 15.
Fixes: b17de076062a ("spi/bcm63xx: work around inability to keep CS up")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20230629071453.62024-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0760d5d0e9f0c0e2200a0323a61d1995bb745dee ]
The Intel Mount Evans SoC's Integrated Management Complex uses the SPI
controller for access to a NOR SPI FLASH. However, the SoC doesn't
provide a mechanism to override the native chip select signal.
This driver doesn't use DMA for memory operations when a chip select
override is not provided due to the native chip select timing behavior.
As a result no DMA configuration is done for the controller and this
configuration is not tested.
The controller also has an errata where a full TX FIFO can result in
data corruption. The suggested workaround is to never completely fill
the FIFO. The TX FIFO has a size of 32 so the fifo_len is set to 31.
Signed-off-by: Abe Kohandel <abe.kohandel@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230606145402.474866-2-abe.kohandel@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c1f23ad34fcdace50275a6aa1e1969b41c6233f ]
If neither a "hif_mspi" nor "mspi" resource is present, the driver will
just early exit in probe but still return success. Apart from not doing
anything meaningful, this would then also lead to a null pointer access
on removal, as platform_get_drvdata() would return NULL, which it would
then try to dereference when trying to unregister the spi master.
Fix this by unconditionally calling devm_ioremap_resource(), as it can
handle a NULL res and will then return a viable ERR_PTR() if we get one.
The "return 0;" was previously a "goto qspi_resource_err;" where then
ret was returned, but since ret was still initialized to 0 at this place
this was a valid conversion in 63c5395bb7a9 ("spi: bcm-qspi: Fix
use-after-free on unbind"). The issue was not introduced by this commit,
only made more obvious.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Kamal Dasu <kamal.dasu@broadcom.com>
Link: https://lore.kernel.org/r/20230629134306.95823-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d10005837be83906bbd2078c3b4f9dfcbd6c95b6 ]
The GPI DMA mode requires for TX DMA to be prepared. Force SPI core to
provide TX buffer even if the caller didn't provide one by setting the
SPI_CONTROLLER_MUST_TX flag.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230629095847.3648597-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f34baf67e4d08908fd94ff29c825bb673295336 ]
n_bytes variable in the driver represents the number of bytes per word
that needs to be sent/copied to fifo. Bits/word can be between 8 and 32
bits from the client but in memory they are a power of 2, same is mentioned
in spi.h header:
"
* @bits_per_word: Data transfers involve one or more words; word sizes
* like eight or 12 bits are common. In-memory wordsizes are
* powers of two bytes (e.g. 20 bit samples use 32 bits).
* This may be changed by the device's driver, or left at the
* default (0) indicating protocol words are eight bit bytes.
* The spi_transfer.bits_per_word can override this for each transfer.
"
Hence, round of n_bytes to a power of 2 to avoid values like 3 which
would generate unalligned/odd accesses to memory/fifo.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Fixes: a51acc2400d4 ("spi: dw: Add support for 32-bits max xfer size")
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com
Signed-off-by: Joy Chakraborty <joychakr@google.com
Reviewed-by: Serge Semin <fancer.lancer@gmail.com
Tested-by: Serge Semin <fancer.lancer@gmail.com
Link: https://lore.kernel.org/r/20230512104746.1797865-4-joychakr@google.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5fd7c99ecf45c8ee8a9b1268f0ffc91cc6271da2 ]
The CS_TOGGLE bit when set is supposed to instruct FW to
toggle CS line between words. The driver with intent of
disabling this behaviour has been unsetting BIT(0). This has
not caused any trouble so far because the original BIT(1)
is untouched and BIT(0) likely wasn't being used.
Correct this to prevent a potential future bug.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org
Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP")
Reviewed-by: Douglas Anderson <dianders@chromium.org
Link: https://lore.kernel.org/r/1682412128-1913-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9728fb3ce11729aa8c276825ddf504edeb00611d ]
When all bits of IER are set to 0, we still can observe the lpspi irq events
when using DMA mode to transfer data.
So disable irq to avoid the too much irq events.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20230505063557.3962220-1-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d7054fb3ac2e8d252aae1268f20623f244e644f ]
Now spi_geni_grab_gpi_chan() errors are correctly reported, the
-EPROBE_DEFER error should be returned from probe in case the
GPI dma driver is built as module and/or not probed yet.
Fixes: b59c122484ec ("spi: spi-geni-qcom: Add support for GPI dma")
Fixes: 6532582c353f ("spi: spi-geni-qcom: fix error handling in spi_geni_grab_gpi_chan()")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230615-topic-sm8550-upstream-fix-spi-geni-qcom-probe-v2-1-670c3d9e8c9c@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
