IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 134061163ee5ca4759de5c24ca3bd71608891ba7 upstream.
Fix UBSAN warnings that occur when using a system with 32 physical
cpu cores or more, or when the user defines a number of Ethernet
queues greater than or equal to FP_SB_MAX_E1x using the num_queues
module parameter.
Currently there is a read/write out of bounds that occurs on the array
"struct stats_query_entry query" present inside the "bnx2x_fw_stats_req"
struct in "drivers/net/ethernet/broadcom/bnx2x/bnx2x.h".
Looking at the definition of the "struct stats_query_entry query" array:
struct stats_query_entry query[FP_SB_MAX_E1x+
BNX2X_FIRST_QUEUE_QUERY_IDX];
FP_SB_MAX_E1x is defined as the maximum number of fast path interrupts and
has a value of 16, while BNX2X_FIRST_QUEUE_QUERY_IDX has a value of 3
meaning the array has a total size of 19.
Since accesses to "struct stats_query_entry query" are offset-ted by
BNX2X_FIRST_QUEUE_QUERY_IDX, that means that the total number of Ethernet
queues should not exceed FP_SB_MAX_E1x (16). However one of these queues
is reserved for FCOE and thus the number of Ethernet queues should be set
to [FP_SB_MAX_E1x -1] (15) if FCOE is enabled or [FP_SB_MAX_E1x] (16) if
it is not.
This is also described in a comment in the source code in
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h just above the Macro definition
of FP_SB_MAX_E1x. Below is the part of this explanation that it important
for this patch
/*
* The total number of L2 queues, MSIX vectors and HW contexts (CIDs) is
* control by the number of fast-path status blocks supported by the
* device (HW/FW). Each fast-path status block (FP-SB) aka non-default
* status block represents an independent interrupts context that can
* serve a regular L2 networking queue. However special L2 queues such
* as the FCoE queue do not require a FP-SB and other components like
* the CNIC may consume FP-SB reducing the number of possible L2 queues
*
* If the maximum number of FP-SB available is X then:
* a. If CNIC is supported it consumes 1 FP-SB thus the max number of
* regular L2 queues is Y=X-1
* b. In MF mode the actual number of L2 queues is Y= (X-1/MF_factor)
* c. If the FCoE L2 queue is supported the actual number of L2 queues
* is Y+1
* d. The number of irqs (MSIX vectors) is either Y+1 (one extra for
* slow-path interrupts) or Y+2 if CNIC is supported (one additional
* FP interrupt context for the CNIC).
* e. The number of HW context (CID count) is always X or X+1 if FCoE
* L2 queue is supported. The cid for the FCoE L2 queue is always X.
*/
However this driver also supports NICs that use the E2 controller which can
handle more queues due to having more FP-SB represented by FP_SB_MAX_E2.
Looking at the commits when the E2 support was added, it was originally
using the E1x parameters: commit f2e0899f0f27 ("bnx2x: Add 57712 support").
Back then FP_SB_MAX_E2 was set to 16 the same as E1x. However the driver
was later updated to take full advantage of the E2 instead of having it be
limited to the capabilities of the E1x. But as far as we can tell, the
array "stats_query_entry query" was still limited to using the FP-SB
available to the E1x cards as part of an oversignt when the driver was
updated to take full advantage of the E2, and now with the driver being
aware of the greater queue size supported by E2 NICs, it causes the UBSAN
warnings seen in the stack traces below.
This patch increases the size of the "stats_query_entry query" array by
replacing FP_SB_MAX_E1x with FP_SB_MAX_E2 to be large enough to handle
both types of NICs.
Stack traces:
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1529:11
index 20 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2e1/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c:1546:11
index 28 is out of range for type 'stats_query_entry [19]'
CPU: 12 PID: 858 Comm: systemd-network Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_prep_fw_stats_req+0x2fd/0x310 [bnx2x]
bnx2x_stats_init+0x156/0x320 [bnx2x]
bnx2x_post_irq_nic_init+0x81/0x1a0 [bnx2x]
bnx2x_nic_load+0x8e8/0x19e0 [bnx2x]
bnx2x_open+0x16b/0x290 [bnx2x]
__dev_open+0x10e/0x1d0
RIP: 0033:0x736223927a0a
Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca
64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89
RSP: 002b:00007ffc0bb2ada8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 0000583df50f9c78 RCX: 0000736223927a0a
RDX: 0000000000000020 RSI: 0000583df50ee510 RDI: 0000000000000003
RBP: 0000583df50d4940 R08: 00007ffc0bb2adb0 R09: 0000000000000080
R10: 0000000000000000 R11: 0000000000000246 R12: 0000583df5103ae0
R13: 000000000000035a R14: 0000583df50f9c30 R15: 0000583ddddddf00
</TASK>
---[ end trace ]---
------------[ cut here ]------------
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1895:8
index 29 is out of range for type 'stats_query_entry [19]'
CPU: 13 PID: 163 Comm: kworker/u96:1 Not tainted 6.9.0-060900rc7-generic
#202405052133
Hardware name: HP ProLiant DL360 Gen9/ProLiant DL360 Gen9,
BIOS P89 10/21/2019
Workqueue: bnx2x bnx2x_sp_task [bnx2x]
Call Trace:
<TASK>
dump_stack_lvl+0x76/0xa0
dump_stack+0x10/0x20
__ubsan_handle_out_of_bounds+0xcb/0x110
bnx2x_iov_adjust_stats_req+0x3c4/0x3d0 [bnx2x]
bnx2x_storm_stats_post.part.0+0x4a/0x330 [bnx2x]
? bnx2x_hw_stats_post+0x231/0x250 [bnx2x]
bnx2x_stats_start+0x44/0x70 [bnx2x]
bnx2x_stats_handle+0x149/0x350 [bnx2x]
bnx2x_attn_int_asserted+0x998/0x9b0 [bnx2x]
bnx2x_sp_task+0x491/0x5c0 [bnx2x]
process_one_work+0x18d/0x3f0
</TASK>
---[ end trace ]---
Fixes: 50f0a562f8cc ("bnx2x: add fcoe statistics")
Signed-off-by: Ghadi Elie Rahme <ghadi.rahme@canonical.com>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20240627111405.1037812-1-ghadi.rahme@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 19d5b2698c35b2132a355c67b4d429053804f8cc upstream.
Explicitly set the 'family' driver_info struct member for leafimx.
Previously, the correct operation relied on KVASER_LEAF being the first
defined value in enum kvaser_usb_leaf_family.
Fixes: e6c80e601053 ("can: kvaser_usb: kvaser_usb_leaf: fix CAN clock frequency regression")
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://lore.kernel.org/all/20240628194529.312968-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8eef5c3cea65f248c99cd9dcb3f84c6509b78162 upstream.
This reverts commit 86167183a17e03ec77198897975e9fdfbd53cb0b.
igc_ptp_init() needs to be called before igc_reset(), otherwise kernel
crash could be observed. Following the corresponding discussion [1] and
[2] revert this commit.
Link: https://lore.kernel.org/all/8fb634f8-7330-4cf4-a8ce-485af9c0a61a@intel.com/ [1]
Link: https://lore.kernel.org/all/87o78rmkhu.fsf@intel.com/ [2]
Fixes: 86167183a17e ("igc: fix a log entry using uninitialized netdev")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240611162456.961631-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ce34dccbe8fa7d2ef86f2d8e7db2a9b67cabfc3 ]
In case of invalid INI file mlxsw_linecard_types_init() deallocates memory
but doesn't reset pointer to NULL and returns 0. In case of any error
occurred after mlxsw_linecard_types_init() call, mlxsw_linecards_init()
calls mlxsw_linecard_types_fini() which performs memory deallocation again.
Add pointer reset to NULL.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: b217127e5e4e ("mlxsw: core_linecards: Add line card objects and implement provisioning")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20240703203251.8871-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e271ff53807e8f2c628758290f0e499dbe51cb3d ]
In function bond_option_arp_ip_targets_set(), if newval->string is an
empty string, newval->string+1 will point to the byte after the
string, causing an out-of-bound read.
BUG: KASAN: slab-out-of-bounds in strlen+0x7d/0xa0 lib/string.c:418
Read of size 1 at addr ffff8881119c4781 by task syz-executor665/8107
CPU: 1 PID: 8107 Comm: syz-executor665 Not tainted 6.7.0-rc7 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x150 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:364 [inline]
print_report+0xc1/0x5e0 mm/kasan/report.c:475
kasan_report+0xbe/0xf0 mm/kasan/report.c:588
strlen+0x7d/0xa0 lib/string.c:418
__fortify_strlen include/linux/fortify-string.h:210 [inline]
in4_pton+0xa3/0x3f0 net/core/utils.c:130
bond_option_arp_ip_targets_set+0xc2/0x910
drivers/net/bonding/bond_options.c:1201
__bond_opt_set+0x2a4/0x1030 drivers/net/bonding/bond_options.c:767
__bond_opt_set_notify+0x48/0x150 drivers/net/bonding/bond_options.c:792
bond_opt_tryset_rtnl+0xda/0x160 drivers/net/bonding/bond_options.c:817
bonding_sysfs_store_option+0xa1/0x120 drivers/net/bonding/bond_sysfs.c:156
dev_attr_store+0x54/0x80 drivers/base/core.c:2366
sysfs_kf_write+0x114/0x170 fs/sysfs/file.c:136
kernfs_fop_write_iter+0x337/0x500 fs/kernfs/file.c:334
call_write_iter include/linux/fs.h:2020 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x96a/0xd80 fs/read_write.c:584
ksys_write+0x122/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
---[ end trace ]---
Fix it by adding a check of string length before using it.
Fixes: f9de11a16594 ("bonding: add ip checks when store ip target")
Signed-off-by: Yue Sun <samsun1006219@gmail.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://patch.msgid.link/20240702-bond-oob-v6-1-2dfdba195c19@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 39ab8fff623053a50951b659e5f6b72343d7d78c ]
Commit 205c50306acf ("wifi: wilc1000: fix RCU usage in connect path")
made sure that the IEs data was manipulated under the relevant RCU section.
Unfortunately, while doing so, the commit brought a faulty implicit cast
from int to u8 on the ies_len variable, making the parsing fail to be
performed correctly if the IEs block is larger than 255 bytes. This failure
can be observed with Access Points appending a lot of IEs TLVs in their
beacon frames (reproduced with a Pixel phone acting as an Access Point,
which brough 273 bytes of IE data in my testing environment).
Fix IEs parsing by removing this undesired implicit cast.
Fixes: 205c50306acf ("wifi: wilc1000: fix RCU usage in connect path")
Signed-off-by: Jozef Hopko <jozef.hopko@altana.com>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240701-wilc_fix_ies_data-v1-1-7486cbacf98a@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e15a5d821e5192a3769d846079bc9aa380139baf ]
The following is emitted when using idxd (DSA) dmanegine as the data
mover for ntb_transport that ntb_netdev uses.
[74412.546922] BUG: using smp_processor_id() in preemptible [00000000] code: irq/52-idxd-por/14526
[74412.556784] caller is netif_rx_internal+0x42/0x130
[74412.562282] CPU: 6 PID: 14526 Comm: irq/52-idxd-por Not tainted 6.9.5 #5
[74412.569870] Hardware name: Intel Corporation ArcherCity/ArcherCity, BIOS EGSDCRB1.E9I.1752.P05.2402080856 02/08/2024
[74412.581699] Call Trace:
[74412.584514] <TASK>
[74412.586933] dump_stack_lvl+0x55/0x70
[74412.591129] check_preemption_disabled+0xc8/0xf0
[74412.596374] netif_rx_internal+0x42/0x130
[74412.600957] __netif_rx+0x20/0xd0
[74412.604743] ntb_netdev_rx_handler+0x66/0x150 [ntb_netdev]
[74412.610985] ntb_complete_rxc+0xed/0x140 [ntb_transport]
[74412.617010] ntb_rx_copy_callback+0x53/0x80 [ntb_transport]
[74412.623332] idxd_dma_complete_txd+0xe3/0x160 [idxd]
[74412.628963] idxd_wq_thread+0x1a6/0x2b0 [idxd]
[74412.634046] irq_thread_fn+0x21/0x60
[74412.638134] ? irq_thread+0xa8/0x290
[74412.642218] irq_thread+0x1a0/0x290
[74412.646212] ? __pfx_irq_thread_fn+0x10/0x10
[74412.651071] ? __pfx_irq_thread_dtor+0x10/0x10
[74412.656117] ? __pfx_irq_thread+0x10/0x10
[74412.660686] kthread+0x100/0x130
[74412.664384] ? __pfx_kthread+0x10/0x10
[74412.668639] ret_from_fork+0x31/0x50
[74412.672716] ? __pfx_kthread+0x10/0x10
[74412.676978] ret_from_fork_asm+0x1a/0x30
[74412.681457] </TASK>
The cause is due to the idxd driver interrupt completion handler uses
threaded interrupt and the threaded handler is not hard or soft interrupt
context. However __netif_rx() can only be called from interrupt context.
Change the call to netif_rx() in order to allow completion via normal
context for dmaengine drivers that utilize threaded irq handling.
While the following commit changed from netif_rx() to __netif_rx(),
baebdf48c360 ("net: dev: Makes sure netif_rx() can be invoked in any context."),
the change should've been a noop instead. However, the code precedes this
fix should've been using netif_rx_ni() or netif_rx_any_context().
Fixes: 548c237c0a99 ("net: Add support for NTB virtual ethernet device")
Reported-by: Jerry Dai <jerry.dai@intel.com>
Tested-by: Jerry Dai <jerry.dai@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://patch.msgid.link/20240701181538.3799546-1-dave.jiang@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c93a6f62cb1bd097aef2e4588648a420d175eee2 ]
On vPro systems, the configuration of the I219-LM to achieve power
gating and S0ix residency is split between the driver and the CSME FW.
It was discovered that in some scenarios, where the network cable is
connected and then disconnected, S0ix residency is not always reached.
This was root-caused to a subset of I219-LM register writes that are not
performed by the CSME FW. Therefore, the driver should perform these
register writes on corporate setups, regardless of the CSME FW state.
This was discovered on Meteor Lake systems; however it is likely to
appear on other platforms as well.
Fixes: cc23f4f0b6b9 ("e1000e: Add support for Meteor Lake")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218589
Signed-off-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240628201754.2744221-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1da839eab6dbc26b95bfcd1ed1a4d1aaa5c144a3 ]
In the cited commit, mqprio_rl cleanup and free are mistakenly removed
in mlx5e_priv_cleanup(), and it causes the leakage of host memory and
firmware SCHEDULING_ELEMENT objects while changing eswitch mode. So,
add them back.
Fixes: 0bb7228f7096 ("net/mlx5e: Fix mqprio_rl handling on devlink reload")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b20c2fb45470d0c7a603613c9cfa5d45720e17f2 ]
Currently, ingress acl is used for three features. It is created only
when vport metadata match and prio tag are enabled. But active-backup
lag mode also uses it. It is independent of vport metadata match and
prio tag. And vport metadata match can be disabled using the
following devlink command:
# devlink dev param set pci/0000:08:00.0 name esw_port_metadata \
value false cmode runtime
If ingress acl is not created, will hit panic when creating drop rule
for active-backup lag mode. If always create it, there will be about
5% performance degradation.
Fix it by creating ingress acl when needed. If esw_port_metadata is
true, ingress acl exists, then create drop rule using existing
ingress acl. If esw_port_metadata is false, create ingress acl and
then create drop rule.
Fixes: 1749c4c51c16 ("net/mlx5: E-switch, add drop rule support to ingress ACL")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86167183a17e03ec77198897975e9fdfbd53cb0b ]
During successful probe, igc logs this:
[ 5.133667] igc 0000:01:00.0 (unnamed net_device) (uninitialized): PHC added
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The reason is that igc_ptp_init() is called very early, even before
register_netdev() has been called. So the netdev_info() call works
on a partially uninitialized netdev.
Fix this by calling igc_ptp_init() after register_netdev(), right
after the media autosense check, just as in igb. Add a comment,
just as in igb.
Now the log message is fine:
[ 5.200987] igc 0000:01:00.0 eth0: PHC added
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c7f3950a9fd53a62b156c0fe7c3a2c43b0ba19b ]
Since commit a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240430-mv88e6xx-list_empty-v3-1-c35c69d88d2e@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d8fb63e46c884c898a38f061c2330f7729e75510 upstream.
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Signed-off-by: Vitor Soares <vitor.soares@toradex.com>
Link: https://lore.kernel.org/all/20240517134355.770777-1-ivitro@gmail.com
[mkl: use more imperative wording in patch description]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 058722ee350c0bdd664e467156feb2bf5d9cc271 upstream.
Avoid spurious link status logs that may ultimately be wrong; for example,
if the link is set to down with the cable plugged, then the cable is
unplugged and after this the link is set to up, the last new log that is
appearing is incorrectly telling that the link is up.
In order to avoid errors, show link status logs after link_reset
processing, and in order to avoid spurious as much as possible, only show
the link loss when some link status change is detected.
cc: stable@vger.kernel.org
Fixes: e2ca90c276e1 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d33fe1714a44ff540629b149d8fab4ac6967585c ]
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Link: https://lore.kernel.org/r/20240331053441.1276826-3-dawei.li@shingroup.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1c4b4d45263241ec6c2405a8df8265d4b58e707 ]
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd6183 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d963c95bc9840d070a788c35e41b715a648717f7 ]
Errata DS80000758 states that carrier sense back pressure mode can cause
link down issues in 100BASE-TX half duplex mode. The datasheet also
recommends to always use the collision based back pressure mode.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Woojung Huh <Woojung.huh@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54a4e5c16382e871c01dd82b47e930fdce30406b ]
PHY_ID_KSZ9477 was supported but not added to the device table passed to
MODULE_DEVICE_TABLE.
Fixes: fc3973a1fa09 ("phy: micrel: add Microchip KSZ 9477 Switch PHY support")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49bbeb5719c2f56907d3a9623b47c6c15c2c431d ]
There are 2 types of outstanding tx skb's:
Type 1: Packets that are sitting in the drivers ind_buff that are
waiting to be batch sent to the NIC. During a device reset, these are
freed with a call to ibmvnic_tx_scrq_clean_buffer()
Type 2: Packets that have been sent to the NIC and are awaiting a TX
completion IRQ. These are free'd during a reset with a call to
clean_tx_pools()
During any reset which requires us to free the tx irq, ensure that the
Type 2 skb references are freed. Since the irq is released, it is
impossible for the NIC to inform of any completions.
Furthermore, later in the reset process is a call to init_tx_pools()
which marks every entry in the tx pool as free (ie not outstanding).
So if the driver is to make a call to init_tx_pools(), it must first
be sure that the tx pool is empty of skb references.
This issue was discovered by observing the following in the logs during
EEH testing:
TX free map points to untracked skb (tso_pool 0 idx=4)
TX free map points to untracked skb (tso_pool 0 idx=5)
TX free map points to untracked skb (tso_pool 1 idx=36)
Fixes: 65d6470d139a ("ibmvnic: clean pending indirect buffs during reset")
Signed-off-by: Nick Child <nnac123@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c28947de2bed40217cf256c5d0d16880054fcf13 ]
The following two shared buffer operations make use of the Shared Buffer
Status Register (SBSR):
# devlink sb occupancy snapshot pci/0000:01:00.0
# devlink sb occupancy clearmax pci/0000:01:00.0
The register has two masks of 256 bits to denote on which ingress /
egress ports the register should operate on. Spectrum-4 has more than
256 ports, so the register was extended by cited commit with a new
'port_page' field.
However, when filling the register's payload, the driver specifies the
ports as absolute numbers and not relative to the first port of the port
page, resulting in memory corruptions [1].
Fix by specifying the ports relative to the first port of the port page.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
Read of size 1 at addr ffff8881068cb00f by task devlink/1566
[...]
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
mlxsw_devlink_sb_occ_snapshot+0x75/0xb0
devlink_nl_sb_occ_snapshot_doit+0x1f9/0x2a0
genl_family_rcv_msg_doit+0x20c/0x300
genl_rcv_msg+0x567/0x800
netlink_rcv_skb+0x170/0x450
genl_rcv+0x2d/0x40
netlink_unicast+0x547/0x830
netlink_sendmsg+0x8d4/0xdb0
__sys_sendto+0x49b/0x510
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
copy_verifier_state+0xbc2/0xfb0
do_check_common+0x2c51/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x109/0x170
__kasan_slab_free+0x14/0x30
kfree+0xca/0x2b0
free_verifier_state+0xce/0x270
do_check_common+0x4828/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fixes: f8538aec88b4 ("mlxsw: Add support for more than 256 ports in SBSR register")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad53f5f54f351e967128edbc431f0f26427172cf ]
The very first flush in any port will flush all learned addresses in all
ports. This can be observed by unplugging the cable from one port while
additional ports are connected and dumping the fdb entries.
This problem is caused by the initially wrong value programmed to the
REG_SW_LUE_CTRL_1 register. Setting SW_FLUSH_STP_TABLE and
SW_FLUSH_MSTP_TABLE bits does not have an immediate effect. It is when
ksz9477_flush_dyn_mac_table() is called then the SW_FLUSH_STP_TABLE bit
takes effect and flushes all learned entries. After that call both bits
are reset and so the next port flush will not cause such problem again.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/1718756202-2731-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7be4cb7189f747b4e5b6977d0e4387bde3204e62 upstream.
After ecf848eb934b ("net: usb: ax88179_178a: fix link status when link is
set to down/up") to not reset from usbnet_open after the reset from
usbnet_probe at initialization stage to speed up this, some issues have
been reported.
It seems to happen that if the initialization is slower, and some time
passes between the probe operation and the open operation, the second reset
from open is necessary too to have the device working. The reason is that
if there is no activity with the phy, this is "disconnected".
In order to improve this, the solution is to detect when the phy is
"disconnected", and we can use the phy status register for this. So we will
only reset the device from reset operation in this situation, that is, only
if necessary.
The same bahavior is happening when the device is stopped (link set to
down) and later is restarted (link set to up), so if the phy keeps working
we only need to enable the mac again, but if enough time passes between the
device stop and restart, reset is necessary, and we can detect the
situation checking the phy status register too.
cc: stable@vger.kernel.org # 6.6+
Fixes: ecf848eb934b ("net: usb: ax88179_178a: fix link status when link is set to down/up")
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Reported-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Reported-by: Arne Fitzenreiter <arne_f@ipfire.org>
Tested-by: Yongqin Liu <yongqin.liu@linaro.org>
Tested-by: Antje Miederhöfer <a.miederhoefer@gmx.de>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8851346912a1fa33e7a5966fe51f07313b274627 upstream.
Assign the configured channel value to the EXTTS event in the timestamp
interrupt handler. Without assigning the correct channel, applications
like ts2phc will refuse to accept the event, resulting in errors such
as:
...
ts2phc[656.834]: config item end1.ts2phc.pin_index is 0
ts2phc[656.834]: config item end1.ts2phc.channel is 3
ts2phc[656.834]: config item end1.ts2phc.extts_polarity is 2
ts2phc[656.834]: config item end1.ts2phc.extts_correction is 0
...
ts2phc[656.862]: extts on unexpected channel
ts2phc[658.141]: extts on unexpected channel
ts2phc[659.140]: extts on unexpected channel
Fixes: f4da56529da60 ("net: stmmac: Add support for external trigger timestamping")
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20240618073821.619751-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fba383985354e83474f95f36d7c65feb75dba19d ]
This functions retrieves values by passing a pointer. As the function
that retrieves them can fail before touching the pointers, the variables
must be initialized.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+5186630949e3c55f0799@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20240619132816.11526-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e7962114c10957fe4d10a15eb714578a394e90b ]
The current code only restores PTP tx_avail count when we get DMA
mapping errors. Fix it so that the PTP tx_avail count will be
restored for both DMA mapping errors and skb_pad() errors.
Otherwise PTP TX timestamp will not be available after a PTP
packet hits the skb_pad() error.
Fixes: 83bb623c968e ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240618215313.29631-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74382aebc9035470ec4c789bdb0d09d8c14f261e ]
Adding/updating VSI list rule, as well as allocating/freeing VSI list
resource are called several times with type ICE_SW_LKUP_LAST, which fails
because ice_update_vsi_list_rule() and ice_aq_alloc_free_vsi_list()
consider it invalid. Allow calling these functions with ICE_SW_LKUP_LAST.
This fixes at least one issue in switchdev mode, where the same rule with
different action cannot be added, e.g.:
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF1_PR
tc filter add dev $PF1 ingress protocol arp prio 0 flower skip_sw \
dst_mac ff:ff:ff:ff:ff:ff action mirred egress redirect dev $VF2_PR
Fixes: 0f94570d0cae ("ice: allow adding advanced rules")
Suggested-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240618210206.981885-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b95a4afe2defd6f46891985f9436a568cd35a31c ]
otx2_sq_append_skb makes used of __vlan_hwaccel_push_inside()
to unoffload VLANs - push them from skb meta data into skb data.
However, it omitts a check for __vlan_hwaccel_push_inside()
returning NULL.
Found by inspection based on [1] and [2].
Compile tested only.
[1] Re: [PATCH net-next v1] net: stmmac: Enable TSO on VLANs
https://lore.kernel.org/all/ZmrN2W8Fye450TKs@shell.armlinux.org.uk/
[2] Re: [PATCH net-next v2] net: stmmac: Enable TSO on VLANs
https://lore.kernel.org/all/CANn89i+11L5=tKsa7V7Aeyxaj6nYGRwy35PAbCRYJ73G+b25sg@mail.gmail.com/
Fixes: fd9d7859db6c ("octeontx2-pf: Implement ingress/egress VLAN offload")
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 604141c036e1b636e2a71cf6e1aa09d1e45f40c2 ]
In virtio spec 0.95, VIRTIO_NET_F_GUEST_CSUM was designed to handle
partially checksummed packets, and the validation of fully checksummed
packets by the device is independent of VIRTIO_NET_F_GUEST_CSUM
negotiation. However, the specification erroneously stated:
"If VIRTIO_NET_F_GUEST_CSUM is not negotiated, the device MUST set flags
to zero and SHOULD supply a fully checksummed packet to the driver."
This statement is inaccurate because even without VIRTIO_NET_F_GUEST_CSUM
negotiation, the device can still set the VIRTIO_NET_HDR_F_DATA_VALID flag.
Essentially, the device can facilitate the validation of these packets'
checksums - a process known as RX checksum offloading - removing the need
for the driver to do so.
This scenario is currently not implemented in the driver and requires
correction. The necessary specification correction[1] has been made and
approved in the virtio TC vote.
[1] https://lists.oasis-open.org/archives/virtio-comment/202401/msg00011.html
Fixes: 4f49129be6fa ("virtio-net: Set RXCSUM feature if GUEST_CSUM is available")
Signed-off-by: Heng Qi <hengqi@linux.alibaba.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8c43360f6e424131fa81d3ba8792ad8ff25a09e ]
commit be27b8965297 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b8965297 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44d3ffd85db03ebcc3090e55589e10d5af9f3a9 ]
When the system resumes from sleep, the phy_init_hw() function invokes
config_init(), which clears all interrupt masks and causes wake events to be
lost in subsequent wake sequences. Remove interrupt mask clearing from
config_init() and preserve relevant masks in config_intr().
Fixes: 7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ba13995be9b416ea1d3daaf3ba871a67f45899b ]
GPY2xx devices need 3 seconds to fully switch out of loopback mode
before it can safely re-enter loopback mode. Implement timeout mechanism
to guarantee 3 seconds waited before re-enter loopback mode.
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: c44d3ffd85db ("net: phy: mxl-gpy: Remove interrupt mask clearing from config_init")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8c248cd836014339498486f14f435c0e344183a7 ]
Prevent options not supported by the PHY from being requested to it by the MAC
Whenever a WOL option is supported by both, the PHY is given priority
since that usually leads to better power savings.
Fixes: e9e13b6adc33 ("lan743x: fix for potential NULL pointer dereference with bare card")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7725363936a88351b71495774c1e0e852ae4cdca ]
When Wake-on-LAN (WoL) is active and the system is in suspend mode, triggering
a system event can wake the system from sleep, which may block the data path.
To restore normal data path functionality after waking, disable all wake-up
events. Furthermore, clear all Write 1 to Clear (W1C) status bits by writing
1's to them.
Fixes: 4d94282afd95 ("lan743x: Add power management support")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2d7198278ece01818cd95a3beffbdf8b2a353fa0 ]
The whole mechanism to remember occurred SPI interrupts is not atomic,
which could lead to unexpected behavior. So fix this by using atomic bit
operations instead.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20240614145030.7781-1-wahrenst@gmx.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc69ad74867dba1377abe14356c94a946d9837a3 ]
A bug in https://bugzilla.kernel.org/show_bug.cgi?id=218906 describes
that irdma would break and report hardware initialization failed after
suspend/resume with Intel E810 NIC (tested on 6.9.0-rc5).
The problem is caused due to the collision between the irq numbers
requested in irdma and the irq numbers requested in other drivers
after suspend/resume.
The irq numbers used by irdma are derived from ice's ice_pf->msix_entries
which stores mappings between MSI-X index and Linux interrupt number.
It's supposed to be cleaned up when suspend and rebuilt in resume but
it's not, causing irdma using the old irq numbers stored in the old
ice_pf->msix_entries to request_irq() when resume. And eventually
collide with other drivers.
This patch fixes this problem. On suspend, we call ice_deinit_rdma() to
clean up the ice_pf->msix_entries (and free the MSI-X vectors used by
irdma if we've dynamically allocated them). On resume, we call
ice_init_rdma() to rebuild the ice_pf->msix_entries (and allocate the
MSI-X vectors if we would like to dynamically allocate them).
Fixes: f9f5301e7e2d ("ice: Register auxiliary device to provide RDMA")
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b8db6afbc95258175da69f31c9bfbea539aaa74 ]
Simplify probe flow by moving all RDMA related code to ice_init_rdma().
Unroll irq allocation if RDMA initialization fails.
Implement ice_deinit_rdma() and use it in remove flow.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: bc69ad74867d ("ice: avoid IRQ collision to fix init failure on ACPI S3 resume")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ecf0b2b8a37c8464186620bef37812a117ff6366 ]
During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.
This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5edc6585aafefa3d44fb8a84adf241d90227f7a3 ]
This switch family supports four LEDs for each of its six ports. Each
LED group is composed of one of these four LEDs from all six ports. LED
groups can be configured to display hardware information, such as link
activity, or manually controlled through a bitmap in registers
RTL8366RB_LED_0_1_CTRL_REG and RTL8366RB_LED_2_3_CTRL_REG.
After a reset, the default LED group configuration for groups 0 to 3
indicates, respectively, link activity, link at 1000M, 100M, and 10M, or
RTL8366RB_LED_CTRL_REG as 0x5432. These configurations are commonly used
for LED indications. However, the driver was replacing that
configuration to use manually controlled LEDs (RTL8366RB_LED_FORCE)
without providing a way for the OS to control them. The default
configuration is deemed more useful than fixed, uncontrollable turned-on
LEDs.
The driver was enabling/disabling LEDs during port_enable/disable.
However, these events occur when the port is administratively controlled
(up or down) and are not related to link presence. Additionally, when a
port N was disabled, the driver was turning off all LEDs for group N,
not only the corresponding LED for port N in any of those 4 groups. In
such cases, if port 0 was brought down, the LEDs for all ports in LED
group 0 would be turned off. As another side effect, the driver was
wrongly warning that port 5 didn't have an LED ("no LED for port 5").
Since showing the administrative state of ports is not an orthodox way
to use LEDs, it was not worth it to fix it and all this code was
dropped.
The code to disable LEDs was simplified only changing each LED group to
the RTL8366RB_LED_OFF state. Registers RTL8366RB_LED_0_1_CTRL_REG and
RTL8366RB_LED_2_3_CTRL_REG are only used when the corresponding LED
group is configured with RTL8366RB_LED_FORCE and they don't need to be
cleaned. The code still references an LED controlled by
RTL8366RB_INTERRUPT_CONTROL_REG, but as of now, no test device has
actually used it. Also, some magic numbers were replaced by macros.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61752ac69b69ed2e04444d090f6917c77ab36d42 ]
gcc-9 and some other older versions produce a false-positive warning
for zeroing two fields
In file included from include/linux/string.h:369,
from drivers/net/wireless/ath/ath9k/main.c:18:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at drivers/net/wireless/ath/ath9k/main.c:140:3:
include/linux/fortify-string.h:462:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
462 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using a struct_group seems to reliably avoid the warning and
not make the code much uglier. The combined memset() should even
save a couple of cpu cycles.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-3-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9b9741854a9fe9df948af49ca5514e0ed0429df ]
In case of token is released due to token->state == BNXT_HWRM_DEFERRED,
released token (set to NULL) is used in log messages. This issue is
expected to be prevented by HWRM_ERR_CODE_PF_UNAVAILABLE error code. But
this error code is returned by recent firmware. So some firmware may not
return it. This may lead to NULL pointer dereference.
Adjust this issue by adding token pointer check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8fa4219dba8e ("bnxt_en: add dynamic debug support for HWRM messages")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240611082547.12178-1-amishin@t-argos.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be27b896529787e23a35ae4befb6337ce73fcca0 ]
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61aee ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b9f756344416e02b41439bf2324b26aa25e141c ]
TSO currently fails when the skb's gso_type field has more than one bit
set.
TSO packets can be passed from userspace using PF_PACKET, TUNTAP and a
few others, using virtio_net_hdr (e.g., PACKET_VNET_HDR). This includes
virtualization, such as QEMU, a real use-case.
The gso_type and gso_size fields as passed from userspace in
virtio_net_hdr are not trusted blindly by the kernel. It adds gso_type
|= SKB_GSO_DODGY to force the packet to enter the software GSO stack
for verification.
This issue might similarly come up when the CWR bit is set in the TCP
header for congestion control, causing the SKB_GSO_TCP_ECN gso_type bit
to be set.
Fixes: a57e5de476be ("gve: DQO: Add TX path")
Signed-off-by: Joshua Washington <joshwash@google.com>
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
v2 - Remove unnecessary comments, remove line break between fixes tag
and signoffs.
v3 - Add back unrelated empty line removal.
Link: https://lore.kernel.org/r/20240610225729.2985343-1-joshwash@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791b4089e326271424b78f2fae778b20e53d071b ]
Move the vxlan_features_check() call to after we verified the packet is
a tunneled VXLAN packet.
Without this, tunneled UDP non-VXLAN packets (for ex. GENENVE) might
wrongly not get offloaded.
In some cases, it worked by chance as GENEVE header is the same size as
VXLAN, but it is obviously incorrect.
Fixes: e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ae073f5903f6c6439d0ac855836a4da5c0a701 ]
When innerprotoinherit is set, the tunneled packets do not have an inner
Ethernet header.
Change 'maclen' to not always assume the header length is ETH_HLEN, as
there might not be a MAC header.
This resolves issues with drivers (e.g. mlx5, in
mlx5e_tx_tunnel_accel()) who rely on the skb inner network header offset
to be correct, and use it for TX offloads.
Fixes: d8a6213d70ac ("geneve: fix header validation in geneve[6]_xmit_skb")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44711b78608c98a3e6b49ce91678cd0917d5349 ]
In lio_vf_rep_copy_packet() pg_info->page is compared to a NULL value,
but then it is unconditionally passed to skb_add_rx_frag() which looks
strange and could lead to null pointer dereference.
lio_vf_rep_copy_packet() call trace looks like:
octeon_droq_process_packets
octeon_droq_fast_process_packets
octeon_droq_dispatch_pkt
octeon_create_recv_info
...search in the dispatch_list...
->disp_fn(rdisp->rinfo, ...)
lio_vf_rep_pkt_recv(struct octeon_recv_info *recv_info, ...)
In this path there is no code which sets pg_info->page to NULL.
So this check looks unneeded and doesn't solve potential problem.
But I guess the author had reason to add a check and I have no such card
and can't do real test.
In addition, the code in the function liquidio_push_packet() in
liquidio/lio_core.c does exactly the same.
Based on this, I consider the most acceptable compromise solution to
adjust this issue by moving skb_add_rx_frag() into conditional scope.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 1f233f327913 ("liquidio: switchdev support for LiquidIO NIC")
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 968fde83841a8c23558dfbd0a0c69d636db52b55 ]
Currently hns3 ring buffer init process would hold cpu too long with big
Tx/Rx ring depth. This could cause soft lockup.
So this patch adds cond_resched() to the process. Then cpu can break to
run other tasks instead of busy looping.
Fixes: a723fb8efe29 ("net: hns3: refine for set ring parameters")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cda920212a49fa22d9e8b9492ac4ea013310a4 ]
When link status change, the nic driver need to notify the roce
driver to handle this event, but at this time, the roce driver
may uninit, then cause kernel crash.
To fix the problem, when link status change, need to check
whether the roce registered, and when uninit, need to wait link
update finish.
Fixes: 45e92b7e4e27 ("net: hns3: add calling roce callback function when link status change")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96b2933152fd87b6a41765b2f58b158fde855b6 ]
If the module is in SFP_MOD_ERROR, `sfp_sm_mod_remove()` will
not be run. As a consequence, `sfp_hwmon_remove()` is not getting
run either, leaving a stale `hwmon` device behind. `sfp_sm_mod_remove()`
itself checks `sfp->sm_mod_state` anyways, so this check was not
really needed in the first place.
Fixes: d2e816c0293f ("net: sfp: handle module remove outside state machine")
Signed-off-by: "Csókás, Bence" <csokas.bence@prolan.hu>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240605084251.63502-1-csokas.bence@prolan.hu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
