IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 7d3b793faaab1305994ce568b59d61927235f57b upstream.
When enabling access to the special register set, Receiver time-out and
RHR interrupts can happen. In this case, the IRQ handler will try to read
from the FIFO thru the RHR register at address 0x00, but address 0x00 is
mapped to DLL register, resulting in erroneous FIFO reading.
Call graph example:
sc16is7xx_startup(): entry
sc16is7xx_ms_proc(): entry
sc16is7xx_set_termios(): entry
sc16is7xx_set_baud(): DLH/DLL = $009C --> access special register set
sc16is7xx_port_irq() entry --> IIR is 0x0C
sc16is7xx_handle_rx() entry
sc16is7xx_fifo_read(): --> unable to access FIFO (RHR) because it is
mapped to DLL (LCR=LCR_CONF_MODE_A)
sc16is7xx_set_baud(): exit --> Restore access to general register set
Fix the problem by claiming the efr_lock mutex when accessing the Special
register set.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240723125302.1305372-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 133f4c00b8b2bfcacead9b81e7e8edfceb4b06c4 upstream.
Sometimes, when a packet is received on channel A at almost the same time
as a packet is about to be transmitted on channel B, we observe with a
logic analyzer that the received packet on channel A is transmitted on
channel B. In other words, the Tx buffer data on channel B is corrupted
with data from channel A.
The problem appeared since commit 4409df5866b7 ("serial: sc16is7xx: change
EFR lock to operate on each channels"), which changed the EFR locking to
operate on each channel instead of chip-wise.
This commit has introduced a regression, because the EFR lock is used not
only to protect the EFR registers access, but also, in a very obscure and
undocumented way, to protect access to the data buffer, which is shared by
the Tx and Rx handlers, but also by each channel of the IC.
Fix this regression first by switching to kfifo_out_linear_ptr() in
sc16is7xx_handle_tx() to eliminate the need for a shared Rx/Tx buffer.
Secondly, replace the chip-wise Rx buffer with a separate Rx buffer for
each channel.
Fixes: 4409df5866b7 ("serial: sc16is7xx: change EFR lock to operate on each channels")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240723125302.1305372-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6eabce6608d6f3440f4c03aa3d3ef50a47a3d193 upstream.
Calling ioctl TIOCSSERIAL with an invalid baud_base can
result in uartclk being zero, which will result in a
divide by zero error in uart_get_divisor(). The check for
uartclk being zero in uart_set_info() needs to be done
before other settings are made as subsequent calls to
ioctl TIOCSSERIAL for the same port would be impacted if
the uartclk check was done where uartclk gets set.
Oops: divide error: 0000 PREEMPT SMP KASAN PTI
RIP: 0010:uart_get_divisor (drivers/tty/serial/serial_core.c:580)
Call Trace:
<TASK>
serial8250_get_divisor (drivers/tty/serial/8250/8250_port.c:2576
drivers/tty/serial/8250/8250_port.c:2589)
serial8250_do_set_termios (drivers/tty/serial/8250/8250_port.c:502
drivers/tty/serial/8250/8250_port.c:2741)
serial8250_set_termios (drivers/tty/serial/8250/8250_port.c:2862)
uart_change_line_settings (./include/linux/spinlock.h:376
./include/linux/serial_core.h:608 drivers/tty/serial/serial_core.c:222)
uart_port_startup (drivers/tty/serial/serial_core.c:342)
uart_startup (drivers/tty/serial/serial_core.c:368)
uart_set_info (drivers/tty/serial/serial_core.c:1034)
uart_set_info_user (drivers/tty/serial/serial_core.c:1059)
tty_set_serial (drivers/tty/tty_io.c:2637)
tty_ioctl (drivers/tty/tty_io.c:2647 drivers/tty/tty_io.c:2791)
__x64_sys_ioctl (fs/ioctl.c:52 fs/ioctl.c:907
fs/ioctl.c:893 fs/ioctl.c:893)
do_syscall_64 (arch/x86/entry/common.c:52
(discriminator 1) arch/x86/entry/common.c:83 (discriminator 1))
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
Reported-by: syzkaller <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: George Kennedy <george.kennedy@oracle.com>
Rule: add
Link: https://lore.kernel.org/stable/1721148848-9784-1-git-send-email-george.kennedy%40oracle.com
Link: https://lore.kernel.org/r/1721219078-3209-1-git-send-email-george.kennedy@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm GENI serial driver did not handle buffer flushing and used
to print discarded characters when the circular buffer was cleared.
Since commit 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
this instead resulted in a hard lockup due to
qcom_geni_serial_send_chunk_fifo() spinning indefinitely in the
interrupt handler.
The underlying bugs have now been fixed, but make sure to output NUL
characters instead of killing the machine if a similar driver bug is
ever reintroduced.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm GENI serial driver does not handle buffer flushing and used
to continue printing discarded characters when the circular buffer was
cleared. Since commit 1788cf6a91d9 ("tty: serial: switch from circ_buf
to kfifo") this instead results in a hard lockup due to
qcom_geni_serial_send_chunk_fifo() spinning indefinitely in the
interrupt handler.
This is easily triggered by interrupting a command such as dmesg in a
serial console but can also happen when stopping a serial getty on
reboot.
Implement the flush_buffer() callback and use it to cancel any active TX
command when the write buffer has been emptied.
Reported-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/lkml/20240610222515.3023730-1-dianders@chromium.org/
Fixes: 1788cf6a91d9 ("tty: serial: switch from circ_buf to kfifo")
Fixes: a1fee899e5be ("tty: serial: qcom_geni_serial: Fix softlock")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stop_tx() callback is used to implement software flow control and
must not discard data as the Qualcomm GENI driver is currently doing
when there is an active TX command.
Cancelling an active command can also leave data in the hardware FIFO,
which prevents the watermark interrupt from being enabled when TX is
later restarted. This results in a soft lockup and is easily triggered
by stopping TX using software flow control in a serial console but this
can also happen after suspend.
Fix this by only stopping any active command, and effectively clearing
the hardware fifo, when shutting down the port. When TX is later
restarted, a transfer command may need to be issued to discard any stale
data that could prevent the watermark interrupt from firing.
Fixes: c4f528795d1a ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Cc: stable@vger.kernel.org # 4.17
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240704101805.30612-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process is killed while writing to a /dev/ttymxc* device in RS485
mode, we observe that the RTS signal is left high, thus making it
impossible for other devices to transmit anything.
Moreover, the ->tx_state variable is left in state SEND, which means
that when one next opens the device and configures baud rate etc., the
initialization code in imx_uart_set_termios dutifully ensures the RTS
pin is pulled down, but since ->tx_state is already SEND, the logic in
imx_uart_start_tx() does not in fact pull the pin high before
transmitting, so nothing actually gets on the wire on the other side
of the transceiver. Only when that transmission is allowed to complete
is the state machine then back in a consistent state.
This is completely reproducible by doing something as simple as
seq 10000 > /dev/ttymxc0
and hitting ctrl-C, and watching with a logic analyzer.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable <stable@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20240625184206.508837-1-linux@rasmusvillemoes.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pdev->dev.of_node can be NULL if the "serial" node is absent.
Add a NULL check to return an error in such cases.
Fixes: 930cbf92db01 ("tty: serial: Add Nuvoton ma35d1 serial driver support")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/8df7ce45-fd58-4235-88f7-43fe7cd67e8f@moroto.mountain/
Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20240625064128.127-1-ychuang570808@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Errata i2310[0] says, Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts.
Commit 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
which added the workaround but missed ensuring RX FIFO is really empty
before applying the errata workaround as recommended in the errata text.
Fix this by adding back check for UART_OMAP_RX_LVL to be 0 for
workaround to take effect.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: 9d141c1e6157 ("serial: 8250_omap: Implementation of Errata i2310")
Cc: stable@vger.kernel.org
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Closes: https://lore.kernel.org/all/e96d0c55-0b12-4cbf-9d23-48963543de49@ti.com/
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240625160725.2102194-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit a81dbd0463ec ("serial: imx: set receiver level before
starting uart") we set the receiver level to its default value. This
caused a regression when using SDMA, where the receiver level is 9
instead of 8 (default). This change will first check if the receiver
level is zero and only then set it to the default. This still avoids the
interrupt storm when the receiver level is zero.
Fixes: a81dbd0463ec ("serial: imx: set receiver level before starting uart")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240703112543.148304-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 787a1cabac01c99846070fcf702e53befaf89f79.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a0f32e2dd99867b164bfebcf36729c2a0d41b30b.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a8b04cfe7dad84e65df5996e14b435fd356fe62c.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4547cd76f08a6f301f6ad563f5d0e4566924ec6b.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b20172ca6bf489534892b801a5db41bbf5ceec75.
Let's roll back all of the serial core and printk console changes that
went into 6.10-rc1 as there still are problems with them that need to be
sorted out.
Link: https://lore.kernel.org/r/ZnpRozsdw6zbjqze@tlindgre-MOBL1
Reported-by: Petr Mladek <pmladek@suse.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: John Ogness <john.ogness@linutronix.de>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When bcm63xx-uart was converted to uart_port_tx_limited(), it implicitly
added a call to stop_tx(). This causes garbage to be put out on the
serial console. To fix this, pass UART_TX_NOSTOP in flags, and manually
call stop_tx() ourselves analogue to how a similar issue was fixed in
commit 7be50f2e8f20 ("serial: mxs-auart: fix tx").
Fixes: d11cc8c3c4b6 ("tty: serial: use uart_port_tx_limited()")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240606195632.173255-4-doug@schmorgal.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the receiver level to something > 0 before calling imx_uart_start_rx
in rs485_config. This is necessary to avoid an interrupt storm that
might prevent the system from booting. This was seen on an i.MX7 device
when the rs485-rts-active-low property was active in the device tree.
Fixes: 6d215f83e5fc ("serial: imx: warn user when using unsupported configuration")
Cc: stable <stable@kernel.org>
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Link: https://lore.kernel.org/r/20240621153829.183780-1-eichest@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the colfires have up to 5 UARTs but MCF54418 has up-to 10 !
Change the maximum value authorized.
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org>
Cc: stable <stable@kernel.org>
Fixes: 2545cf6e94b4 ("m68knommu: allow 4 coldfire serial ports")
Link: https://lore.kernel.org/r/20240620-upstream-uart-v1-1-a9d0d95fb19e@yoseli.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per Errata i2310[0], Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts, therefore apply Errata i2310 solution.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
Fixes: b67e830d38fa ("serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs")
Cc: stable@vger.kernel.org
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20240619105903.165434-1-u-kumar1@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally, the number of ports is indicated by the third digit of the
device ID on Moxa PCI serial boards. For example, `0x1121` indicates a
device with 2 ports.
However, `CP116E_A_A` and `CP116E_A_B` are exceptions; they have 8
ports, but the third digit of the device ID is `6`.
This patch introduces a function to retrieve the number of ports on Moxa
PCI serial boards, addressing the issue described above.
Fixes: 37058fd5d239 ("tty: serial: 8250: Add support for MOXA Mini PCIe boards")
Cc: stable <stable@kernel.org>
Signed-off-by: Crescent Hsieh <crescentcy.hsieh@moxa.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20240617063058.18866-1-crescentcy.hsieh@moxa.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d49216438139
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
removed Kconfig SPI_MASTER or I2C dependency for SERIAL_SC16IS7XX (core).
This removal was done because I inadvertently misinterpreted some review
comments.
Because of that, the driver question now pops up if both I2C and
SPI_MASTER are disabled.
Re-add Kconfig SPI_MASTER or I2C dependency to fix the problem.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d49216438139 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d49216438139
("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
renamed SERIAL_SC16IS7XX_CORE by SERIAL_SC16IS7XX. This means that some
configs should have been updated when I submitted the original patch, but
unfortunately they were not. Geert mentioned for example:
arch/mips/configs/cu1??0-neo_defconfig
Rename SERIAL_SC16IS7XX to SERIAL_SC16IS7XX_CORE so that existing configs
will still work correctly.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d49216438139 ("serial: sc16is7xx: split into core and I2C/SPI parts (core)")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240603152601.3689319-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, suspend testing on sc7180-trogdor based devices has started
to sometimes fail with messages like this:
port a88000.serial:0.0: PM: calling pm_runtime_force_suspend+0x0/0xf8 @ 28934, parent: a88000.serial:0
port a88000.serial:0.0: PM: dpm_run_callback(): pm_runtime_force_suspend+0x0/0xf8 returns -16
port a88000.serial:0.0: PM: pm_runtime_force_suspend+0x0/0xf8 returned -16 after 33 usecs
port a88000.serial:0.0: PM: failed to suspend: error -16
I could reproduce these problems by logging in via an agetty on the
debug serial port (which was _not_ used for kernel console) and
running:
cat /var/log/messages
...and then (via an SSH session) forcing a few suspend/resume cycles.
Tracing through the code and doing some printf()-based debugging shows
that the -16 (-EBUSY) comes from the recently added
serial_port_runtime_suspend().
The idea of the serial_port_runtime_suspend() function is to prevent
the port from being _runtime_ suspended if it still has bytes left to
transmit. Having bytes left to transmit isn't a reason to block
_system_ suspend, though. If a serdev device in the kernel needs to
block system suspend it should block its own suspend and it can use
serdev_device_wait_until_sent() to ensure bytes are sent.
The DEFINE_RUNTIME_DEV_PM_OPS() used by the serial_port code means
that the system suspend function will be pm_runtime_force_suspend().
In pm_runtime_force_suspend() we can see that before calling the
runtime suspend function we'll call pm_runtime_disable(). This should
be a reliable way to detect that we're called from system suspend and
that we shouldn't look for busyness.
Fixes: 43066e32227e ("serial: port: Don't suspend if the port is still busy")
Cc: stable@vger.kernel.org
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20240531080914.v3.1.I2395e66cf70c6e67d774c56943825c289b9c13e4@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The FIFO is 64 bytes, but the FCR is configured to fire the TX interrupt
when the FIFO is half empty (bit 3 = 0). Thus, we should only write 32
bytes when a TX interrupt occurs.
This fixes a problem observed on the PXA168 that dropped a bunch of TX
bytes during large transmissions.
Fixes: ab28f51c77cd ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: Doug Brown <doug@schmorgal.com>
Link: https://lore.kernel.org/r/20240519191929.122202-1-doug@schmorgal.com
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d9666dfb314e1ffd6eb9c3c4243fe3e094c047a7.
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Fix the mistake made in the past by moving the respective definitions
to the specific driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The container of the struct dw8250_port_data is private to the actual
driver. In particular, 8250_lpss and 8250_dw use different data types
that are assigned to the UART port private_data. Hence, it must not
be used outside the specific driver.
Currently the only cpr_val is required by the common code, make it
be available via struct dw8250_port_data.
This fixes the UART breakage on Intel Galileo boards.
Fixes: 593dea000bc1 ("serial: 8250: dw: Allow to use a fallback CPR value if not synthesized")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240514190730.2787071-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this.)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZlBGKQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOkwCfUOa00YQt3jJwBEC9bQUprW1z95MAoKW00V5g
UJgQ7+1d+o4bT/ib5xpj
=/O0m
-----END PGP SIGNATURE-----
Merge tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small TTY and Serial driver fixes that missed the
6.9-final merge window, but have been in my tree for weeks (my fault,
travel caused me to miss this)
These fixes include:
- more n_gsm fixes for reported problems
- 8520_mtk driver fix
- 8250_bcm7271 driver fix
- sc16is7xx driver fix
All of these have been in linux-next for weeks without any reported
problems"
* tag 'tty-6.10-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sc16is7xx: fix bug in sc16is7xx_set_baud() when using prescaler
serial: 8250_bcm7271: use default_mux_rate if possible
serial: 8520_mtk: Set RTS on shutdown for Rx in-band wakeup
tty: n_gsm: fix missing receive state reset after mode switch
tty: n_gsm: fix possible out-of-bounds in gsm0_receive()
Here is the big set of tty/serial driver changes for 6.10-rc1. Included
in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos instead
of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZk4Cvg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymqpwCgnHU1NeBBUsvoSDOLk5oApIQ4jVgAn102jWlw
3dNDhA4i3Ay/mZdv8/Kj
=TI+P
-----END PGP SIGNATURE-----
Merge tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty/serial driver changes for 6.10-rc1.
Included in here are:
- Usual good set of api cleanups and evolution by Jiri Slaby to make
the serial interfaces move out of the 1990's by using kfifos
instead of hand-rolling their own logic.
- 8250_exar driver updates
- max3100 driver updates
- sc16is7xx driver updates
- exar driver updates
- sh-sci driver updates
- tty ldisc api addition to help refuse bindings
- other smaller serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (113 commits)
serial: Clear UPF_DEAD before calling tty_port_register_device_attr_serdev()
serial: imx: Raise TX trigger level to 8
serial: 8250_pnp: Simplify "line" related code
serial: sh-sci: simplify locking when re-issuing RXDMA fails
serial: sh-sci: let timeout timer only run when DMA is scheduled
serial: sh-sci: describe locking requirements for invalidating RXDMA
serial: sh-sci: protect invalidating RXDMA on shutdown
tty: add the option to have a tty reject a new ldisc
serial: core: Call device_set_awake_path() for console port
dt-bindings: serial: brcm,bcm2835-aux-uart: convert to dtschema
tty: serial: uartps: Add support for uartps controller reset
arm64: zynqmp: Add resets property for UART nodes
dt-bindings: serial: cdns,uart: Add optional reset property
serial: 8250_pnp: Switch to DEFINE_SIMPLE_DEV_PM_OPS()
serial: 8250_exar: Keep the includes sorted
serial: 8250_exar: Make type of bit the same in exar_ee_*_bit()
serial: 8250_exar: Use BIT() in exar_ee_read()
serial: 8250_exar: Switch to use dev_err_probe()
serial: 8250_exar: Return directly from switch-cases
serial: 8250_exar: Decrease indentation level
...
-----BEGIN PGP SIGNATURE-----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=xjoS
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Skip E820 checks for MCFG ECAM regions for new (2016+) machines,
since there's no requirement to describe them in E820 and some
platforms require ECAM to work (Bjorn Helgaas)
- Rename PCI_IRQ_LEGACY to PCI_IRQ_INTX to be more specific (Damien
Le Moal)
- Remove last user and pci_enable_device_io() (Heiner Kallweit)
- Wait for Link Training==0 to avoid possible race (Ilpo Järvinen)
- Skip waiting for devices that have been disconnected while
suspended (Ilpo Järvinen)
- Clear Secondary Status errors after enumeration since Master Aborts
and Unsupported Request errors are an expected part of enumeration
(Vidya Sagar)
MSI:
- Remove unused IMS (Interrupt Message Store) support (Bjorn Helgaas)
Error handling:
- Mask Genesys GL975x SD host controller Replay Timer Timeout
correctable errors caused by a hardware defect; the errors cause
interrupts that prevent system suspend (Kai-Heng Feng)
- Fix EDR-related _DSM support, which previously evaluated revision 5
but assumed revision 6 behavior (Kuppuswamy Sathyanarayanan)
ASPM:
- Simplify link state definitions and mask calculation (Ilpo
Järvinen)
Power management:
- Avoid D3cold for HP Pavilion 17 PC/1972 PCIe Ports, where BIOS
apparently doesn't know how to put them back in D0 (Mario
Limonciello)
CXL:
- Support resetting CXL devices; special handling required because
CXL Ports mask Secondary Bus Reset by default (Dave Jiang)
DOE:
- Support DOE Discovery Version 2 (Alexey Kardashevskiy)
Endpoint framework:
- Set endpoint BAR to be 64-bit if the driver says that's all the
device supports, in addition to doing so if the size is >2GB
(Niklas Cassel)
- Simplify endpoint BAR allocation and setting interfaces (Niklas
Cassel)
Cadence PCIe controller driver:
- Drop DT binding redundant msi-parent and pci-bus.yaml (Krzysztof
Kozlowski)
Cadence PCIe endpoint driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
Freescale Layerscape PCIe controller driver:
- Convert DT binding to YAML (Frank Li)
MediaTek MT7621 PCIe controller driver:
- Add DT binding missing 'reg' property for child Root Ports
(Krzysztof Kozlowski)
- Fix theoretical string truncation in PHY name (Sergio Paracuellos)
NVIDIA Tegra194 PCIe controller driver:
- Return success for endpoint probe instead of falling through to the
failure path (Vidya Sagar)
Renesas R-Car PCIe controller driver:
- Add DT binding missing IOMMU properties (Geert Uytterhoeven)
- Add DT binding R-Car V4H compatible for host and endpoint mode
(Yoshihiro Shimoda)
Rockchip PCIe controller driver:
- Configure endpoint BARs to be 64-bit based on the BAR type, not the
BAR value (Niklas Cassel)
- Add DT binding missing maxItems to ep-gpios (Krzysztof Kozlowski)
- Set the Subsystem Vendor ID, which was previously zero because it
was masked incorrectly (Rick Wertenbroek)
Synopsys DesignWare PCIe controller driver:
- Restructure DBI register access to accommodate devices where this
requires Refclk to be active (Manivannan Sadhasivam)
- Remove the deinit() callback, which was only need by the
pcie-rcar-gen4, and do it directly in that driver (Manivannan
Sadhasivam)
- Add dw_pcie_ep_cleanup() so drivers that support PERST# can clean
up things like eDMA (Manivannan Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to make it parallel
to dw_pcie_ep_init() (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
reflect the actual functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from all the glue
drivers, not just those that require active Refclk from the host
(Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which was an obscure way for
glue drivers to indicate that they depend on Refclk from the host
(Manivannan Sadhasivam)
TI J721E PCIe driver:
- Add DT binding J784S4 SoC Device ID (Siddharth Vadapalli)
- Add DT binding J722S SoC support (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Add DT binding missing num-viewport, phys and phy-name properties
(Jan Kiszka)
Miscellaneous:
- Constify and annotate with __ro_after_init (Heiner Kallweit)
- Convert DT bindings to YAML (Krzysztof Kozlowski)
- Check for kcalloc() failure in of_pci_prop_intr_map() (Duoming
Zhou)"
* tag 'pci-v6.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Do not wait for disconnected devices when resuming
x86/pci: Skip early E820 check for ECAM region
PCI: Remove unused pci_enable_device_io()
ata: pata_cs5520: Remove unnecessary call to pci_enable_device_io()
PCI: Update pci_find_capability() stub return types
PCI: Remove PCI_IRQ_LEGACY
scsi: vmw_pvscsi: Do not use PCI_IRQ_LEGACY instead of PCI_IRQ_LEGACY
scsi: pmcraid: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: mpt3sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: megaraid_sas: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: ipr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: hpsa: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
scsi: arcmsr: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
wifi: rtw89: Use PCI_IRQ_INTX instead of PCI_IRQ_LEGACY
dt-bindings: PCI: rockchip,rk3399-pcie: Add missing maxItems to ep-gpios
Revert "genirq/msi: Provide constants for PCI/IMS support"
Revert "x86/apic/msi: Enable PCI/IMS"
Revert "iommu/vt-d: Enable PCI/IMS"
Revert "iommu/amd: Enable PCI/IMS"
Revert "PCI/MSI: Provide IMS (Interrupt Message Store) support"
...
Nine patches this cycle and they split into just three topics:
1. Adopt coccinelle's recommendation to adopt str_plural().
2. A set of seven patches to refactor kdb_read() to improve both code clarity
and it's discipline with respect to fixed size buffers. This isn't just a
refactor. Between them these also fix a cursor movement redraw problem and
two buffer overflows (one latent and one real, albeit difficult to
tickle).
3. Fix an NMI-safety problem when enqueuing kdb's keyboard reset code.
I wrote eight of the nine patches in this collection so many thanks to Doug
Anderson for the reviews. The changes that affects drivers/tty/serial is
acked by Greg KH.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
-----BEGIN PGP SIGNATURE-----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=vVUC
-----END PGP SIGNATURE-----
Merge tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux
Pull kgdb updates from Daniel Thompson:
"Nine patches this cycle and they split into just three topics:
- Adopt coccinelle's recommendation to adopt str_plural()
- A set of seven patches to refactor kdb_read() to improve both code
clarity and its discipline with respect to fixed size buffers.
This isn't just a refactor. Between them these also fix a cursor
movement redraw problem and two buffer overflows (one latent and
one real, albeit difficult to tickle).
- Fix an NMI-safety problem when enqueuing kdb's keyboard reset code
I wrote eight of the nine patches in this collection so many thanks to
Doug Anderson for the reviews. The changes that affects
drivers/tty/serial is acked by Greg KH"
* tag 'kgdb-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
serial: kgdboc: Fix NMI-safety problems from keyboard reset code
kdb: Simplify management of tmpbuffer in kdb_read()
kdb: Replace double memcpy() with memmove() in kdb_read()
kdb: Use format-specifiers rather than memset() for padding in kdb_read()
kdb: Merge identical case statements in kdb_read()
kdb: Fix console handling when editing and tab-completing commands
kdb: Use format-strings rather than '\0' injection in kdb_read()
kdb: Fix buffer overflow during tab-complete
kdb: Use str_plural() to fix Coccinelle warning
I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family
in the kernel without native byte access and that Debian has already
dropped support for this generation last year [1] in order to
improve performance for the newer machines.
This topic came up again when Paul E. McKenney noticed that
parts of the RCU code already rely on byte access and do not
work on alpha EV5 reliably, so we decided on using my series to
avoid the problem entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well.
-----BEGIN PGP SIGNATURE-----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=0Sgm
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull alpha updates from Arnd Bergmann:
"I had investigated dropping support for alpha EV5 and earlier a while
ago after noticing that this is the only supported CPU family in the
kernel without native byte access and that Debian has already dropped
support for this generation last year [1] in order to improve
performance for the newer machines.
This topic came up again when Paul McKenney noticed that parts of the
RCU code already rely on byte access and do not work on alpha EV5
reliably, so we decided on using my series to avoid the problem
entirely.
Al Viro did another series for alpha to address all the known build
issues. I rebased his patches without any further changes and included
it as a baseline for my work here to avoid conflicts and allow
backporting the fixes to stable kernels for the now removed hardware
support as well"
[ I dearly loved alpha back in the days, but the lack of byte and word
operations was a horrible mistake and made everything worse -
including very much the crazy IO contortions that resulted from it.
It certainly wasn't the only mistake in the architecture, but it's the
first-order issue.
So while it's a bit sad to see the support for my first alpha go away,
if you want to run museum hardware, maybe you should use museum
kernels.. - Linus ]
* tag 'asm-generic-alpha' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
alpha: drop pre-EV56 support
alpha: cabriolet: remove EV5 CPU support
alpha: remove LCA and APECS based machines
alpha: sable: remove early machine support
alpha: remove DECpc AXP150 (Jensen) support
alpha: trim the unused stuff from asm-offsets.c
alpha: jensen, t2 - make __EXTERN_INLINE same as for the rest
alpha: core_lca: take the unused functions out
alpha: missing includes
alpha: sys_sio: fix misspelled ifdefs
alpha: don't make functions public without a reason
alpha: add clone3() support
alpha: fix modversions for strcpy() et.al.
alpha: sort scr_mem{cpy,move}w() out
If a serdev_device_driver is already loaded for a serdev_tty_port when it
gets registered by tty_port_register_device_attr_serdev() then that
driver's probe() method will be called immediately.
The serdev_device_driver's probe() method should then be able to call
serdev_device_open() successfully, but because UPF_DEAD is still dead
serdev_device_open() will fail with -ENXIO in this scenario:
serdev_device_open()
ctrl->ops->open() /* this callback being ttyport_open() */
tty->ops->open() /* this callback being uart_open() */
tty_port_open()
port->ops->activate() /* this callback being uart_port_activate() */
Find bit UPF_DEAD is set in uport->flags and fail with errno -ENXIO.
Fix this be clearing UPF_DEAD before tty_port_register_device_attr_serdev()
note this only moves up the UPD_DEAD clearing a small bit, before:
tty_port_register_device_attr_serdev();
mutex_unlock(&tty_port.mutex);
uart_port.flags &= ~UPF_DEAD;
mutex_unlock(&port_mutex);
after:
uart_port.flags &= ~UPF_DEAD;
tty_port_register_device_attr_serdev();
mutex_unlock(&tty_port.mutex);
mutex_unlock(&port_mutex);
Reported-by: Weifeng Liu <weifeng.liu.z@gmail.com>
Closes: https://lore.kernel.org/platform-driver-x86/20240505130800.2546640-1-weifeng.liu.z@gmail.com/
Tested-by: Weifeng Liu <weifeng.liu.z@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240509141549.63704-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the default TX trigger level of 2 in non-DMA mode (meaning that an
interrupt is generated when less than 2 characters are left in the
FIFO), we have observed frequent buffer underruns at 115200 Baud on an
i.MX8M Nano. This can cause communication issues if the receiving side
expects a continuous transfer.
Increasing the level to 8 makes the UART trigger an interrupt earlier,
giving the kernel enough time to refill the FIFO, at the cost of
triggering one interrupt per ~24 instead of ~30 bytes of transmitted
data (as the i.MX UART has a 32 byte FIFO).
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20240508133744.35858-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_pnp sets drvdata to line + 1 if the probe is successful. The users
of drvdata are in remove, suspend and resume callbacks, none of which
will be called if probe failed. The line acquired from drvdata can
never be zero in those functions and the checks for that can be
removed.
Eliminate also +/-1 step because all users of line subtract 1 from the
value.
These might have been leftover from legacy PM callbacks that could
be called without probe being successful.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240506121202.11253-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hrtimer for RXDMA timeout was unconditionally restarted in the RXDMA
complete handler ignoring the fact that setting up DMA may fail and PIO
is used instead. Explicitly stop the timer when DMA is completed and
only restart it when setting up DMA was successful. This makes the
intention of the timer much clearer, the driver easier to understand and
simplifies assumptions about the timer. The latter avoids race
conditions if these assumptions were not met or confused.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-9-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The to-be-fixed commit removed locking when invalidating the DMA RX
descriptors on shutdown. It overlooked that there is still a rx_timer
running which may still access the protected data. So, re-add the
locking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/r/ee6c9e16-9f29-450e-81da-4a8dceaa8fc7@de.bosch.com
Fixes: 2c4ee23530ff ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-7-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a high speed clock with a low baud rate, the 4x prescaler is
automatically selected if required. In that case, sc16is7xx_set_baud()
properly configures the chip registers, but returns an incorrect baud
rate by not taking into account the prescaler value. This incorrect baud
rate is then fed to uart_update_timeout().
For example, with an input clock of 80MHz, and a selected baud rate of 50,
sc16is7xx_set_baud() will return 200 instead of 50.
Fix this by first changing the prescaler variable to hold the selected
prescaler value instead of the MCR bitfield. Then properly take into
account the selected prescaler value in the return value computation.
Also add better documentation about the divisor value computation.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20240430200431.4102923-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a scenario when resuming from some power saving states
with no_console_suspend where console output can be generated
before the 8250_bcm7271 driver gets the opportunity to restore
the baud_mux_clk frequency. Since the baud_mux_clk is at its
default frequency at this time the output can be garbled until
the driver gets the opportunity to resume.
Since this is only an issue with console use of the serial port
during that window and the console isn't likely to use baud
rates that require alternate baud_mux_clk frequencies, allow the
driver to select the default_mux_rate if it is accurate enough.
Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240424222559.1844045-1-opendmb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Rx in-band wakeup is enabled, set RTS to true in mtk8250_shutdown()
so the connected device can still send message and trigger IRQ when the
system is suspended.
Fixes: 18c9d4a3c249 ("serial: When UART is suspended, set RTS to false")
Cc: stable <stable@kernel.org>
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Link: https://lore.kernel.org/r/20240424130619.2924456-1-treapking@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the UART port is used as a console, no_console_suspend is
available in bootargs and UART port is part of a software-controlled power
domain we need to call device_set_awake_path(). This lets the power
domain core code know that this domain should not be powered off
during system suspend. Otherwise, the UART port power domain is turned off,
nothing is printed while suspending and the suspend/resume process is
blocked. This was detected on the Renesas RZ/G3S SoC while adding support
for power domains.
Based on code investigation (on v6.9-rc5), this issue is present on other
SoCs (e.g., Renesas R-Mobile A1 [1], IMX8QXP [2]) and different SoCs have
particular implementation to handle it. Due to this the patch added the
call of device_set_awake_path() in uart_suspend_port() instead of having
it in the platform specific UART driver.
[1] drivers/pmdomain/renesas/rmobile-sysc.c:116
[2] drivers/pmdomain/imx/scu-pd.c:357
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Tony Lindgren <tony.lindgren@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240430095930.2806067-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for an optional reset for the uartps controller using
the reset driver. If the uartps node contains the "resets" property,
then cdns_uart_startup performs uartps controller non-pulse out of reset
and reset in exit path.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Link: https://lore.kernel.org/r/20240425062358.1347684-4-manikanta.guntupalli@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SIMPLE_DEV_PM_OPS() is deprecated, replace it with the
DEFINE_SIMPLE_DEV_PM_OPS() and use pm_sleep_ptr() for setting
the driver's PM routines.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20240422083237.207447-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make type of bit parameter and returned one the same in exar_ee_*_bit().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-13-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use BIT() in exar_ee_read() like other functions do.
While at it, explain the EEPROM type and the dummy bit requirement.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to use dev_err_probe() to simplify the error path and
unify a message template.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-11-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two similar switch-cases which use different style.
Unify them and one more to return from the cases directly.
While at it, add missing default in another switch-case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Parker Newman <pnewman@connecttech.com>
Link: https://lore.kernel.org/r/20240503171917.2921250-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
