IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 9e2ab4b18ebd46813fc3459207335af4d368e323 ]
The sample rates set by the rockchip_i2s_tdm driver in master mode are
inaccurate up to 5% in several cases, due to the driver logic to configure
clocks and a nasty interaction with the Common Clock Framework.
To understand what happens, here is the relevant section of the clock tree
(slightly simplified), along with the names used in the driver:
vpll0 _OR_ vpll1 "mclk_root"
clk_i2s2_8ch_tx_src "mclk_parent"
clk_i2s2_8ch_tx_mux
clk_i2s2_8ch_tx "mclk" or "mclk_tx"
This is what happens when playing back e.g. at 192 kHz using
audio-graph-card (when recording the same applies, only s/tx/rx/):
0. at probe, rockchip_i2s_tdm_set_sysclk() stores the passed frequency in
i2s_tdm->mclk_tx_freq (*) which is 50176000, and that is never modified
afterwards
1. when playback is started, rockchip_i2s_tdm_hw_params() is called and
does the following two calls
2. rockchip_i2s_tdm_calibrate_mclk():
2a. selects mclk_root0 (vpll0) as a parent for mclk_parent
(mclk_tx_src), which is OK because the vpll0 rate is a good for
192000 (and sumbultiple) rates
2b. sets the mclk_root frequency based on ppm calibration computations
2c. sets mclk_tx_src to 49152000 (= 256 * 192000), which is also OK as
it is a multiple of the required bit clock
3. rockchip_i2s_tdm_set_mclk()
3a. calls clk_set_rate() to set the rate of mclk_tx (clk_i2s2_8ch_tx)
to the value of i2s_tdm->mclk_tx_freq (*), i.e. 50176000 which is
not a multiple of the sampling frequency -- this is not OK
3a1. clk_set_rate() reacts by reparenting clk_i2s2_8ch_tx_src to
vpll1 -- this is not OK because the default vpll1 rate can be
divided to get 44.1 kHz and related rates, not 192 kHz
The result is that the driver does a lot of ad-hoc decisions about clocks
and ends up in using the wrong parent at an unoptimal rate.
Step 0 is one part of the problem: unless the card driver calls set_sysclk
at each stream start, whatever rate is set in mclk_tx_freq during boot will
be taken and used until reboot. Moreover the driver does not care if its
value is not a multiple of any audio frequency.
Another part of the problem is that the whole reparenting and clock rate
setting logic is conflicting with the CCF algorithms to achieve largely the
same goal: selecting the best parent and setting the closest clock
rate. And it turns out that only calling once clk_set_rate() on
clk_i2s2_8ch_tx picks the correct vpll and sets the correct rate.
The fix is based on removing the custom logic in the driver to select the
parent and set the various clocks, and just let the Clock Framework do it
all. As a side effect, the set_sysclk() op becomes useless because we now
let the CCF compute the appropriate value for the sampling rate. It also
implies that the whole calibration logic is now dead code and so it is
removed along with the "PCM Clock Compensation in PPM" kcontrol, which has
always been broken anyway. The handling of the 4 optional clocks also
becomes dead code and is removed.
The actual rates have been tested playing 30 seconds of audio at various
sampling rates before and after this change using sox:
time play -r <sample_rate> -n synth 30 sine 950 gain -3
The time reported in the table below is the 'real' value reported by the
'time' command in the above command line.
rate before after
--------- ------ ------
8000 Hz 30.60s 30.63s
11025 Hz 30.45s 30.51s
16000 Hz 30.47s 30.50s
22050 Hz 30.78s 30.41s
32000 Hz 31.02s 30.43s
44100 Hz 30.78s 30.41s
48000 Hz 29.81s 30.45s
88200 Hz 30.78s 30.41s
96000 Hz 29.79s 30.42s
176400 Hz 27.40s 30.41s
192000 Hz 29.79s 30.42s
While the tests are running the clock tree confirms that:
* without the patch, vpll1 is always used and clk_i2s2_8ch_tx always
produces 50176000 Hz, which cannot be divided for most audio rates
except the slowest ones, generating inaccurate rates
* with the patch:
- for 192000 Hz vpll0 is used
- for 176400 Hz vpll1 is used
- clk_i2s2_8ch_tx always produces (256 * <rate>) Hz
Tested on the RK3308 using the internal audio codec.
Fixes: 081068fd6414 ("ASoC: rockchip: add support for i2s-tdm controller")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://msgid.link/r/20240305-rk3308-audio-codec-v4-1-312acdbe628f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31e0d0c2cad23e0cc48731634f85bb2d8707790 ]
Using __exit for the remove function results in the remove callback
being discarded with SND_SOC_TLV320ADC3XXX=y. When such a device gets
unbound (e.g. using sysfs or hotplug), the driver is just removed
without the cleanup being performed. This results in resource leaks. Fix
it by compiling in the remove callback unconditionally.
This also fixes a W=1 modpost warning:
WARNING: modpost: sound/soc/codecs/snd-soc-tlv320adc3xxx: section mismatch in reference: adc3xxx_i2c_driver+0x10 (section: .data) -> adc3xxx_i2c_remove (section: .exit.text)
(which only happens with SND_SOC_TLV320ADC3XXX=m).
Fixes: e9a3b57efd28 ("ASoC: codec: tlv320adc3xxx: New codec driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://msgid.link/r/20240310143852.397212-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76f5f55c45b906710c9565a7e68c8d782c46b394 ]
Make calibration functions configurable to support different calibration
data storage modes.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/5859c77ffef752b8a9784713b412d815d7e2688c.1703891777.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 5f51de7e30c7 ("ALSA: hda/tas2781: do not call pm_runtime_force_* in system_resume/suspend")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59c6a3a43b221cc2a211181b1298e43b2c2df782 ]
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
Fixes: d60e4f1e4be5 ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20240223175116.2005407-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3741a8d28a1137f8b19ae6f3d6e3be69a454a0a ]
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
Fixes: d60e4f1e4be5 ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20240223175116.2005407-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98f681b0f84cfc3a1d83287b77697679e0398306 ]
Smatch complains about "head->full_size - head->header_size" can
underflow. To some extent, we're always going to have to trust the
firmware a bit. However, it's easy enough to add a check for negatives,
and let's add a upper bounds check as well.
Fixes: d2458baa799f ("ASoC: SOF: ipc3-loader: Implement firmware parsing and loading")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/r/5593d147-058c-4de3-a6f5-540ecb96f6f8@moroto.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ad992c71b6a8e8a547954addc7af9fbde6ca10a ]
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/t9015.c:274:4: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
274 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Fixes: 33901f5b9b16 ("ASoC: meson: add t9015 internal DAC driver")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://msgid.link/r/20240213215807.3326688-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98ac85a00f31d2e9d5452b825a9ed0153d934043 ]
clang-16 warns about casting functions to incompatible types, as is done
here to call clk_disable_unprepare:
sound/soc/meson/aiu.c:243:12: error: cast from 'void (*)(struct clk *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
243 | (void(*)(void *))clk_disable_unprepare,
The pattern of getting, enabling and setting a disable callback for a
clock can be replaced with devm_clk_get_enabled(), which also fixes
this warning.
Fixes: 6ae9ca9ce986 ("ASoC: meson: aiu: add i2s and spdif support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Link: https://msgid.link/r/20240213215807.3326688-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a6d7c4fb2801b675a9c31a7ceb78c84b8c439bc ]
The devm_request_irq() call is done for "dma_rt" interrupt but the error
message printed "dma_tx" interrupt on failure, fix this by updating
dma_tx -> dma_rt in dev_err_probe() message. While at it aligned the code.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Fixes: 38c042b59af0248a ("ASoC: sh: rz-ssi: Update interrupt handling for half duplex channels")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://msgid.link/r/20240130150822.327434-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 222be59e5eed1554119294edc743ee548c2371d0 ]
Driver uses kasprintf() to initialize fw_{code,data}_bin members of
struct acp_dev_data, but kfree() is never called to deallocate the
memory, which results in a memory leak.
Fix the issue by switching to devm_kasprintf(). Additionally, ensure the
allocation was successful by checking the pointer validity.
Fixes: f7da88003c53 ("ASoC: SOF: amd: Enable signed firmware image loading for Vangogh platform")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-6-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0ada20279db2649a7549a2b8a4a3379c59f238d ]
Handle potential acp_sofdsp_dai_links_create() errors in ACP SOF machine
driver's probe function. Note there is no need for an undo.
While at it, switch to dev_err_probe().
Fixes: 9f84940f5004 ("ASoC: amd: acp: Add SOF audio support on Chrome board")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://msgid.link/r/20231219030728.2431640-4-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96e202f8c52ac49452f83317cf3b34cd1ad81e18 ]
Use source instead of ret, which seems to be unrelated and will always
be zero.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Link: https://msgid.link/r/20240306161439.1385643-5-stuarth@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3a51137607cee7c814cd3a75d96f78b9ee1dc1f ]
The HP Pavilion Aero Laptop 13-be2xxx(8BD6) requires a quirk entry for its internal microphone to function.
Signed-off-by: Al Raj Hassain <alrajhassain@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://msgid.link/r/20240304103924.13673-1-alrajhassain@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8b0127aca8c60826e7354e504a12d4a46b1c3bb ]
The bios version can differ depending if it is a dual-boot variant of the tablet.
Therefore another DMI match is required.
Signed-off-by: Alban Boyé <alban.boye@protonmail.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://msgid.link/r/20240228192807.15130-1-alban.boye@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed00a6945dc32462c2d3744a3518d2316da66fcc ]
Like many other models, the Lenovo 21J2 (ThinkBook 16 G5+ APO)
needs a quirk entry for the internal microphone to function.
Signed-off-by: Jiawei Wang <me@jwang.link>
Link: https://msgid.link/r/20240228073914.232204-2-me@jwang.link
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c40aad7c81e5fba34b70123ed7ce3397fa62a4d2 ]
When the system is suspended while audio is active, the
sof_ipc4_pcm_hw_free() is invoked to reset the pipelines since during
suspend the DSP is turned off, streams will be re-started after resume.
If the firmware crashes during while audio is running (or when we reset
the stream before suspend) then the sof_ipc4_set_multi_pipeline_state()
will fail with IPC error and the state change is interrupted.
This will cause misalignment between the kernel and firmware state on next
DSP boot resulting errors returned by firmware for IPC messages, eventually
failing the audio resume.
On stream close the errors are ignored so the kernel state will be
corrected on the next DSP boot, so the second boot after the DSP panic.
If sof_ipc4_trigger_pipelines() is called from sof_ipc4_pcm_hw_free() then
state parameter is SOF_IPC4_PIPE_RESET and only in this case.
Treat a forced pipeline reset similarly to how we treat a pcm_free by
ignoring error on state sending to allow the kernel's state to be
consistent with the state the firmware will have after the next boot.
Link: https://github.com/thesofproject/sof/issues/8721
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://msgid.link/r/20240213115233.15716-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7fe85b229bc30cb5dc95b4e9015a601c9e3a8cd ]
Like many other models, the Lenovo 82UU (Yoga Slim 7 Pro 14ARH7)
needs a quirk entry for the internal microphone to function.
Signed-off-by: Attila Tőkés <attitokes@gmail.com>
Link: https://msgid.link/r/20240210193638.144028-1-attitokes@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 551539a8606e28cb2a130f8ef3e9834235b456c4 ]
The DMI strings used for the LattePanda board DMI quirks are very generic.
Using the dmidecode database from https://linux-hardware.org/ shows
that the chosen DMI strings also match the following 2 laptops
which also have a rt5645 codec:
Insignia NS-P11W7100 https://linux-hardware.org/?computer=E092FFF8BA04
Insignia NS-P10W8100 https://linux-hardware.org/?computer=AFB6C0BF7934
All 4 hw revisions of the LattePanda board have "S70CR" in their BIOS
version DMI strings:
DF-BI-7-S70CR100-*
DF-BI-7-S70CR110-*
DF-BI-7-S70CR200-*
LP-BS-7-S70CR700-*
See e.g. https://linux-hardware.org/?computer=D98250A817C0
Add a partial (non exact) DMI match on this string to make the LattePanda
board DMI match more precise to avoid false-positive matches.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://msgid.link/r/20240211212736.179605-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1722057477a3786b8c0d60c28fc281f6ecf1cc3 ]
As devm_pm_runtime_enable can fail due to memory allocations, it is
best to handle the error.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240206113850.719888-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4703b014f28bf7a2e56d1da238ee95ef6c5ce76b upstream.
It looks like the "!" character was added accidentally. The
regmap_update_bits_check() function is normally going to succeed. This
means the rest of the function is unreachable and we don't handle the
situation where "changed" is true correctly.
Fixes: 07f7d6e7a124 ("ASoC: cs35l56: Fix for initializing ASP1 mixer registers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/0c254c07-d1c0-4a5c-a22b-7e135cab032c@moroto.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eba2eb2495f47690400331c722868902784e59de ]
snd_soc_card_get_kcontrol() must be holding a read lock on
card->controls_rwsem while walking the controls list.
Compare with snd_ctl_find_numid().
The existing function is renamed snd_soc_card_get_kcontrol_locked()
so that it can be called from contexts that are already holding
card->controls_rwsem (for example, control get/put functions).
There are few direct or indirect callers of
snd_soc_card_get_kcontrol(), and most are safe. Three require
changes, which have been included in this patch:
codecs/cs35l45.c:
cs35l45_activate_ctl() is called from a control put() function so
is changed to call snd_soc_card_get_kcontrol_locked().
codecs/cs35l56.c:
cs35l56_sync_asp1_mixer_widgets_with_firmware() is called from
control get()/put() functions so is changed to call
snd_soc_card_get_kcontrol_locked().
fsl/fsl_xcvr.c:
fsl_xcvr_activate_ctl() is called from three places, one of which
already holds card->controls_rwsem:
1. fsl_xcvr_mode_put(), a control put function, which will
already be holding card->controls_rwsem.
2. fsl_xcvr_startup(), a DAI startup function.
3. fsl_xcvr_shutdown(), a DAI shutdown function.
To fix this, fsl_xcvr_activate_ctl() has been changed to call
snd_soc_card_get_kcontrol_locked() so that it is safe to call
directly from fsl_xcvr_mode_put().
The fsl_xcvr_startup() and fsl_xcvr_shutdown() functions have been
changed to take a read lock on card->controls_rsem() around calls
to fsl_xcvr_activate_ctl(). While this is not very elegant, it
keeps the change small, to avoid this patch creating a large
collateral churn in fsl/fsl_xcvr.c.
Analysis of other callers of snd_soc_card_get_kcontrol() is that
they do not need any changes, they are not holding card->controls_rwsem
when they call snd_soc_card_get_kcontrol().
Direct callers of snd_soc_card_get_kcontrol():
fsl/fsl_spdif.c: fsl_spdif_dai_probe() - DAI probe function
fsl/fsl_micfil.c: voice_detected_fn() - IRQ handler
Indirect callers via soc_component_notify_control():
codecs/cs42l43: cs42l43_mic_shutter() - IRQ handler
codecs/cs42l43: cs42l43_spk_shutter() - IRQ handler
codecs/ak4118.c: ak4118_irq_handler() - IRQ handler
codecs/wm_adsp.c: wm_adsp_write_ctl() - not currently used
Indirect callers via snd_soc_limit_volume():
qcom/sc8280xp.c: sc8280xp_snd_init() - DAIlink init function
ti/rx51.c: rx51_aic34_init() - DAI init function
I don't have hardware to test the fsl/*, qcom/sc828xp.c, ti/rx51.c
and ak4118.c changes.
Backport note:
The fsl/, qcom/, cs35l45, cs35l56 and cs42l43 callers were added
since the Fixes commit so won't all be present on older kernels.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 209c6cdfd283 ("ASoC: soc-card: move snd_soc_card_get_kcontrol() to soc-card")
Link: https://lore.kernel.org/r/20240221123710.690224-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c14f09f010cc569ae7e2f6ef02374f6bfef9917e ]
Rewrite the handling of ASP1 TX mixer mux initialization to prevent a
deadlock during component_remove().
The firmware can overwrite the ASP1 TX mixer registers with
system-specific settings. This is mainly for hardware that uses the
ASP as a chip-to-chip link controlled by the firmware. Because of this
the driver cannot know the starting state of the ASP1 mixer muxes until
the firmware has been downloaded and rebooted.
The original workaround for this was to queue a work function from the
dsp_work() job. This work then read the register values (populating the
regmap cache the first time around) and then called
snd_soc_dapm_mux_update_power(). The problem with this is that it was
ultimately triggered by cs35l56_component_probe() queueing dsp_work,
which meant that it would be running in parallel with the rest of the
ASoC component and card initialization. To prevent accessing DAPM before
it was fully initialized the work function took the card mutex. But this
would deadlock if cs35l56_component_remove() was called before the work job
had completed, because ASoC calls component_remove() with the card mutex
held.
This new version removes the work function. Instead the regmap cache and
DAPM mux widgets are initialized the first time any of the associated ALSA
controls is read or written.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 07f7d6e7a124 ("ASoC: cs35l56: Fix for initializing ASP1 mixer registers")
Link: https://lore.kernel.org/r/20240208123742.1278104-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f6c967941c5d6fa526fdd64733a8d86bf2bfab31 ]
Put the silicon revision and secured flag in the wm_adsp fwf_name
string instead of including them in the part string.
This changes the format of the firmware name string from
cs35l56[s]-rev-misc[-system_name]
to
cs35l56-rev[-s]-misc[-system_name]
No firmware files have been published, so this doesn't cause a
compatibility break.
Silicon revision and secured flag are included in the firmware
filename to pick a firmware compatible with the part. These strings
were being added to the part string, but that is a misuse of the
string. The correct place for these is the fwf_name string, which
is specifically intended to select between multiple firmware files
for the same part.
Backport note:
This won't apply to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 608f1b0dbdde ("ASoC: cs35l56: Move DSP part string generation so that it is done only once")
Link: https://msgid.link/r/20240129162737.497-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07f7d6e7a124d3e4de36771e2a4926d0e31c2258 ]
Defer initializing the state of the ASP1 mixer registers until
the firmware has been downloaded and rebooted.
On a SoundWire system the ASP is free for use as a chip-to-chip
interconnect. This can be either for the firmware on multiple
CS35L56 to share reference audio; or as a bridge to another
device. If it is a firmware interconnect it is owned by the
firmware and the Linux driver should avoid writing the registers.
However, if it is a bridge then Linux may take over and handle
it as a normal codec-to-codec link. Even if the ASP is used
as a firmware-firmware interconnect it is useful to have
ALSA controls for the ASP mixer. They are at least useful for
debugging.
CS35L56 is designed for SDCA and a generic SDCA driver would
know nothing about these chip-specific registers. So if the
ASP is being used on a SoundWire system the firmware sets up the
ASP mixer registers. This means that we can't assume the default
state of these registers. But we don't know the initial state
that the firmware set them to until after the firmware has been
downloaded and booted, which can take several seconds when
downloading multiple amps.
DAPM normally reads the initial state of mux registers during
probe() but this would mean blocking probe() for several seconds
until the firmware has initialized them. To avoid this, the
mixer muxes are set SND_SOC_NOPM to prevent DAPM trying to read
the register state. Custom get/set callbacks are implemented for
ALSA control access, and these can safely block waiting for the
firmware download.
After the firmware download has completed, the state of the
mux registers is known so a work job is queued to call
snd_soc_dapm_mux_update_power() on each of the mux widgets.
Backport note:
This won't apply cleanly to kernels older than v6.6.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07687cd0539f8185b6ba0c0afba8473517116d6a ]
Move the call to cs35l56_set_patch() earlier in cs35l56_init() so
that it only adds the register patch on first-time initialization.
The call was after the post_soft_reset label, so every time this
function was run to re-initialize the hardware after a reset it would
call regmap_register_patch() and add the same reg_sequence again.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 898673b905b9 ("ASoC: cs35l56: Move shared data into a common data structure")
Link: https://msgid.link/r/20240129162737.497-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae861c466ee57e15a29d97629e1c564e3f714a4f ]
The cs35l56->component pointer is used by the suspend-resume handling to
know whether the driver is fully instantiated. This is to prevent it
queuing dsp_work which would result in calling wm_adsp when the driver
is not an instantiated ASoC component. So this pointer must be cleared
by cs35l56_component_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://msgid.link/r/20240129162737.497-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1382d8b55129875b2e07c4d2a7ebc790183769ee ]
In the case where __lpass_get_dmactl_handle is called and the driver
id dai_id is invalid the pointer dmactl is not being assigned a value,
and dmactl contains a garbage value since it has not been initialized
and so the null check may not work. Fix this to initialize dmactl to
NULL. One could argue that modern compilers will set this to zero, but
it is useful to keep this initialized as per the same way in functions
__lpass_platform_codec_intf_init and lpass_cdc_dma_daiops_hw_params.
Cleans up clang scan build warning:
sound/soc/qcom/lpass-cdc-dma.c:275:7: warning: Branch condition
evaluates to a garbage value [core.uninitialized.Branch]
Fixes: b81af585ea54 ("ASoC: qcom: Add lpass CPU driver for codec dma control")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://msgid.link/r/20240221134804.3475989-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d5a2b5dd0a8d2b2b535b5266699429dbd48e62f ]
ASoC is using 2 type of prefix (asoc_xxx() vs snd_soc_xxx()), but there
is no particular reason about that [1].
To reduce confusing, standarding these to snd_soc_xxx() is sensible.
This patch adds asoc_xxx() macro to keep compatible for a while.
It will be removed if all drivers were switched to new style.
Link: https://lore.kernel.org/r/87h6td3hus.wl-kuninori.morimoto.gx@renesas.com [1]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87fs3ks26i.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 1382d8b55129 ("ASoC: qcom: Fix uninitialized pointer dmactl")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e33625c84b75e4f078d7f9bf58f01fe71ab99642 ]
The driver must write 0 to HALO_STATE before sending the SYSTEM_RESET
command to the firmware.
HALO_STATE is in DSP memory, which is preserved across a soft reset.
The SYSTEM_RESET command does not change the value of HALO_STATE.
There is period of time while the CS35L56 is resetting, before the
firmware has started to boot, where a read of HALO_STATE will return
the value it had before the SYSTEM_RESET. If the driver does not
clear HALO_STATE, this would return BOOT_DONE status even though the
firmware has not booted.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 8a731fd37f8b ("ASoC: cs35l56: Move utility functions to shared file")
Link: https://msgid.link/r/20240216140535.1434933-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6122b0b4211d132934ef99e7b737910e6d54d2f ]
This driver includes the legacy GPIO APIs <linux/gpio.h> and
<linux/of_gpio.h> but does not use any symbols from any of
them.
Drop the includes.
Further the driver is requesting "reset-gpios" rather than
just "reset" from the GPIO framework. This is wrong because
the gpiolib core will add "-gpios" before processing the
request from e.g. device tree. Drop the suffix.
The last problem means that the optional RESET GPIO has
never been properly retrieved and used even if it existed,
but nobody noticed.
Fixes: c1124c09e103 ("ASoC: cs35l34: Initial commit of the cs35l34 CODEC driver.")
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231201-descriptors-sound-cirrus-v2-3-ee9f9d4655eb@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daf3f0f99cde93a066240462b7a87cdfeedc04c0 ]
There's no need to overwrite fwf_name with a kstrdup() of the cs_dsp part
name. It is trivial to select either fwf_name or cs_dsp.part as the string
to use when building the filename in wm_adsp_request_firmware_file().
This leaves fwf_name entirely owned by the codec driver.
It also avoids problems with freeing the pointer. With the original code
fwf_name was either a pointer owned by the codec driver, or a kstrdup()
created by wm_adsp. This meant wm_adsp must free it if it set it, but not
if the codec driver set it. The code was handling this by using
devm_kstrdup().
But there is no absolute requirement that wm_adsp_common_init() must be
called from probe(), so this was a pseudo-memory leak - each new call to
wm_adsp_common_init() would allocate another block of memory but these
would only be freed if the owning codec driver was removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://msgid.link/r/20240129162737.497-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0adf963b8463faa44653e22e56ce55f747e68868 ]
The SPDIF hardware block found in the H616 SoC has the same layout as
the one found in the H6 SoC, except that it is missing the receiver
side.
Since the driver currently only supports the transmit function, support
for the H616 is identical to what is currently done for the H6.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://msgid.link/r/20240127163247.384439-4-wens@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cc2aa9a75f2397d42b78d4c159bc06722183c78 ]
Add condition check for cpu dai link initialization for amplifier
codec path, as same pcm id uses for both headset and speaker path
for RENOIR platforms.
Signed-off-by: Venkata Prasad Potturu <venkataprasad.potturu@amd.com>
Link: https://msgid.link/r/20240118143023.1903984-3-venkataprasad.potturu@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 34a1066981a967eab619938e7b35a9be6b4c34e1 upstream.
The tascodec_init() of the snd-soc-tas2781-comlib module is called from
snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls
request_firmware_nowait() with parameter THIS_MODULE and a cont/callback
from the latter modules.
The latter modules can be removed while their callbacks are running,
resulting in a general protection failure.
Add module parameter to tascodec_init() so request_firmware_nowait() can
be called with the module of the callback.
Fixes: ef3bcde75d06 ("ASoC: tas2781: Add tas2781 driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fcbe4873089c84da641df75cda9cac2e9addbb4b upstream.
commit 74ad8ed65121 ("ASoC: SOF: ipc3: Implement rx_msg IPC ops")
introduced a new allocation before the upper bounds check in
do_rx_work. As a result A DSP can cause bad allocations if spewing
garbage.
Fixes: 74ad8ed65121 ("ASoC: SOF: ipc3: Implement rx_msg IPC ops")
Reported-by: Tim Van Patten <timvp@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240213123834.4827-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 086df711d9b886194481b4fbe525eb43e9ae7403 upstream.
WCD938x sound codec driver ignores return status of getting regulators
and returns EINVAL instead of EPROBE_DEFER. If regulator provider
probes after the codec, system is left without probed audio:
wcd938x_codec audio-codec: wcd938x_probe: Fail to obtain platform data
wcd938x_codec: probe of audio-codec failed with error -22
Fixes: 16572522aece ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://msgid.link/r/20240117151208.1219755-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c6dce23ec993f7da7790a9eadb36864ceb60e942 upstream.
The laptop requires a quirk ID to enable its internal microphone. Add
it to the DMI quirk table.
Reported-by: Techno Mooney <techno.mooney@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218402
Cc: stable@vger.kernel.org
Signed-off-by: Techno Mooney <techno.mooney@gmail.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Link: https://msgid.link/r/20240129081148.1044891-1-bagasdotme@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6ef5d5b92f7117b324efaac72b3db27ae8bb3082 ]
There is a path in rt5645_jack_detect_work(), where rt5645->jd_mutex
is left locked forever. That may lead to deadlock
when rt5645_jack_detect_work() is called for the second time.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: cdba4301adda ("ASoC: rt5650: add mutex to avoid the jack detection failure")
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/1707645514-21196-1-git-send-email-khoroshilov@ispras.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7332c4a4f1a7d16f054c6357fb65c597b6a86a7 ]
With the change in the widget free logic to power down the cores only
when the scheduler widgets are freed, we need to ensure that the
scheduler widget is freed only after all the widgets associated with the
scheduler are freed. This is to ensure that the secondary core that the
scheduler is scheduled to run on is kept powered on until all widgets
that need them are in use. While this works well for dynamic pipelines,
in the case of static pipelines the current logic does not take this into
account and frees all widgets in the order they occur in the
widget_list. So, modify this to ensure that the scheduler widgets are freed
only after all other types of widgets in the widget_list are freed.
Link: https://github.com/thesofproject/linux/issues/4807
Fixes: 31ed8da1c8e5 ("ASoC: SOF: sof-audio: Modify logic for enabling/disabling topology cores")
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20240208133432.1688-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b53cc6144a3f6c8b56afcdec89d81195c9b0dc69 upstream.
The PA gain can be set in steps of 1.5 dB from -3 dB to 18 dB, that is,
in 15 levels.
Fix the dB values for the PA volume control as experiments using wsa8835
show that the first 16 levels all map to the same lowest gain while the
last three map to the highest gain.
These values specifically need to be correct for the sound server to
provide proper volume control.
Note that level 0 (-3 dB) does not mute the PA so the mute flag should
also not be set.
Fixes: cdb09e623143 ("ASoC: codecs: wsa883x: add control, dapm widgets and map")
Cc: stable@vger.kernel.org # 6.0
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240119112420.7446-2-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46188db080bd1df7d2d28031b89e56f2fdbabd67 upstream.
The LPASS WSA macro codec driver is updating the digital gain settings
behind the back of user space on DAPM events if companding has been
enabled.
As compander control is exported to user space, this can result in the
digital gain setting being incremented (or decremented) every time the
sound server is started and the codec suspended depending on what the
UCM configuration looks like.
Soon enough playback will become distorted (or too quiet).
This is specifically a problem on the Lenovo ThinkPad X13s as this
bypasses the limit for the digital gain setting that has been set by the
machine driver.
Fix this by simply dropping the compander gain offset hack. If someone
cares about modelling the impact of the compander setting this can
possibly be done by exporting it as a volume control later.
Note that the volume registers still need to be written after enabling
clocks in order for any prior updates to take effect.
Fixes: 2c4066e5d428 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Cc: stable@vger.kernel.org # 5.11
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240119112420.7446-4-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d0e8bdfa4a57099dc7230952a460903f2e2f8de upstream.
The lowest headphones volume setting does not mute so the leave the TLV
mute flag unset.
This is specifically needed to let the sound server use the lowest gain
setting.
Fixes: c03226ba15fe ("ASoC: codecs: wcd938x: fix dB range for HPHL and HPHR")
Cc: <stable@vger.kernel.org> # 6.5
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240122091130.27463-1-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c481016bb4f8a9c059c39ac06e7b65e233a61f6a upstream.
The UCM configuration for the Lenovo ThinkPad X13s has up until now
been setting the speaker PA volume to the minimum -3 dB when enabling
the speakers, but this does not prevent the user from increasing the
volume further.
Limit the digital gain and PA volumes to a combined -3 dB in the machine
driver to reduce the risk of speaker damage until we have active speaker
protection in place (or higher safe levels have been established).
Note that the PA volume limit cannot be set lower than 0 dB or
PulseAudio gets confused when the first 16 levels all map to -3 dB.
Also note that this will probably need to be generalised using
machine-specific limits, but a common limit should do for now.
Cc: <stable@vger.kernel.org> # 6.5
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://msgid.link/r/20240122181819.4038-3-johan+linaro@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
