84c19e655b
The Kconfig help text for baycom drivers suggests that more information on the hardware can be found at <https://www.baycom.de>. The website now includes no information on their ham radio products other than a mention that they were once produced by the company, saying: "The amateur radio equipment is now no longer part and business of BayCom GmbH" As there is no information relavent to the baycom driver on the site, remove the link. Signed-off-by: Peter Lafreniere <peter@n8pjl.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
163 lines
6.2 KiB
Plaintext
163 lines
6.2 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
config MKISS
|
|
tristate "Serial port KISS driver"
|
|
depends on AX25 && TTY
|
|
select CRC16
|
|
help
|
|
KISS is a protocol used for the exchange of data between a computer
|
|
and a Terminal Node Controller (a small embedded system commonly
|
|
used for networking over AX.25 amateur radio connections; it
|
|
connects the computer's serial port with the radio's microphone
|
|
input and speaker output).
|
|
|
|
Although KISS is less advanced than the 6pack protocol, it has
|
|
the advantage that it is already supported by most modern TNCs
|
|
without the need for a firmware upgrade.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called mkiss.
|
|
|
|
config 6PACK
|
|
tristate "Serial port 6PACK driver"
|
|
depends on AX25 && TTY
|
|
help
|
|
6pack is a transmission protocol for the data exchange between your
|
|
PC and your TNC (the Terminal Node Controller acts as a kind of
|
|
modem connecting your computer's serial port to your radio's
|
|
microphone input and speaker output). This protocol can be used as
|
|
an alternative to KISS for networking over AX.25 amateur radio
|
|
connections, but it has some extended functionality.
|
|
|
|
Note that this driver is still experimental and might cause
|
|
problems. For details about the features and the usage of the
|
|
driver, read <file:Documentation/networking/6pack.rst>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called 6pack.
|
|
|
|
config BPQETHER
|
|
tristate "BPQ Ethernet driver"
|
|
depends on AX25
|
|
help
|
|
AX.25 is the protocol used for computer communication over amateur
|
|
radio. If you say Y here, you will be able to send and receive AX.25
|
|
traffic over Ethernet (also called "BPQ AX.25"), which could be
|
|
useful if some other computer on your local network has a direct
|
|
amateur radio connection.
|
|
|
|
config SCC
|
|
tristate "Z8530 SCC driver"
|
|
depends on ISA && AX25
|
|
help
|
|
These cards are used to connect your Linux box to an amateur radio
|
|
in order to communicate with other computers. If you want to use
|
|
this, read
|
|
<file:Documentation/networking/device_drivers/hamradio/z8530drv.rst>
|
|
and the AX25-HOWTO, available from
|
|
<http://www.tldp.org/docs.html#howto>. Also make sure to say Y
|
|
to "Amateur Radio AX.25 Level 2" support.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called scc.
|
|
|
|
config SCC_DELAY
|
|
bool "additional delay for PA0HZP OptoSCC compatible boards"
|
|
depends on SCC
|
|
help
|
|
Say Y here if you experience problems with the SCC driver not
|
|
working properly; please read
|
|
<file:Documentation/networking/device_drivers/hamradio/z8530drv.rst>
|
|
for details.
|
|
|
|
If unsure, say N.
|
|
|
|
config SCC_TRXECHO
|
|
bool "support for TRX that feedback the tx signal to rx"
|
|
depends on SCC
|
|
help
|
|
Some transmitters feed the transmitted signal back to the receive
|
|
line. Say Y here to foil this by explicitly disabling the receiver
|
|
during data transmission.
|
|
|
|
If in doubt, say Y.
|
|
|
|
config BAYCOM_SER_FDX
|
|
tristate "BAYCOM ser12 fullduplex driver for AX.25"
|
|
depends on AX25 && !S390
|
|
select CRC_CCITT
|
|
help
|
|
This is one of two drivers for Baycom style simple amateur radio
|
|
modems that connect to a serial interface. The driver supports the
|
|
ser12 design in full-duplex mode. In addition, it allows the
|
|
baudrate to be set between 300 and 4800 baud (however not all modems
|
|
support all baudrates). This is the preferred driver. The next
|
|
driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
|
|
driver and still provided in case this driver does not work with
|
|
your serial interface chip. To configure the driver, use the sethdlc
|
|
utility available in the standard ax25 utilities package.
|
|
For more information on the modems, see
|
|
<file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called baycom_ser_fdx. This is recommended.
|
|
|
|
config BAYCOM_SER_HDX
|
|
tristate "BAYCOM ser12 halfduplex driver for AX.25"
|
|
depends on AX25 && !S390
|
|
select CRC_CCITT
|
|
help
|
|
This is one of two drivers for Baycom style simple amateur radio
|
|
modems that connect to a serial interface. The driver supports the
|
|
ser12 design in half-duplex mode. This is the old driver. It is
|
|
still provided in case your serial interface chip does not work with
|
|
the full-duplex driver. This driver is deprecated. To configure
|
|
the driver, use the sethdlc utility available in the standard ax25
|
|
utilities package. For more information on the modems, see
|
|
<file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called baycom_ser_hdx. This is recommended.
|
|
|
|
config BAYCOM_PAR
|
|
tristate "BAYCOM picpar and par96 driver for AX.25"
|
|
depends on PARPORT && AX25
|
|
select CRC_CCITT
|
|
help
|
|
This is a driver for Baycom style simple amateur radio modems that
|
|
connect to a parallel interface. The driver supports the picpar and
|
|
par96 designs. To configure the driver, use the sethdlc utility
|
|
available in the standard ax25 utilities package.
|
|
For more information on the modems, see
|
|
<file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called baycom_par. This is recommended.
|
|
|
|
config BAYCOM_EPP
|
|
tristate "BAYCOM epp driver for AX.25"
|
|
depends on PARPORT && AX25 && !64BIT
|
|
select CRC_CCITT
|
|
help
|
|
This is a driver for Baycom style simple amateur radio modems that
|
|
connect to a parallel interface. The driver supports the EPP
|
|
designs. To configure the driver, use the sethdlc utility available
|
|
in the standard ax25 utilities package.
|
|
For more information on the modems, see
|
|
<file:Documentation/networking/device_drivers/hamradio/baycom.rst>.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called baycom_epp. This is recommended.
|
|
|
|
config YAM
|
|
tristate "YAM driver for AX.25"
|
|
depends on AX25 && !S390
|
|
help
|
|
The YAM is a modem for packet radio which connects to the serial
|
|
port and includes some of the functions of a Terminal Node
|
|
Controller. If you have one of those, say Y here.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called yam.
|
|
|
|
|