23d2ed63cd
To improve human readability and enable automatic validation, the tuples in "playback" and "capture" properties in sound device nodes should be grouped using angle brackets. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20210204130517.1647073-3-geert+renesas@glider.be
374 lines
6.3 KiB
Plaintext
374 lines
6.3 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Device Tree Source for the iWave-RZ/G1M/G1N Qseven carrier board
|
|
*
|
|
* Copyright (C) 2017 Renesas Electronics Corp.
|
|
*/
|
|
|
|
/*
|
|
* SSI-SGTL5000
|
|
*
|
|
* This command is required when Playback/Capture
|
|
*
|
|
* amixer set "DVC Out" 100%
|
|
* amixer set "DVC In" 100%
|
|
*
|
|
* You can use Mute
|
|
*
|
|
* amixer set "DVC Out Mute" on
|
|
* amixer set "DVC In Mute" on
|
|
*
|
|
* You can use Volume Ramp
|
|
*
|
|
* amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
|
|
* amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
|
|
* amixer set "DVC Out Ramp" on
|
|
* aplay xxx.wav &
|
|
* amixer set "DVC Out" 80% // Volume Down
|
|
* amixer set "DVC Out" 100% // Volume Up
|
|
*/
|
|
|
|
/ {
|
|
aliases {
|
|
serial0 = &scif0;
|
|
serial3 = &scifb1;
|
|
ethernet0 = &avb;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
audio_clock: audio_clock {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <26000000>;
|
|
};
|
|
|
|
lcd_backlight: backlight {
|
|
compatible = "pwm-backlight";
|
|
|
|
pwms = <&pwm3 0 5000000 0>;
|
|
brightness-levels = <0 4 8 16 32 64 128 255>;
|
|
default-brightness-level = <7>;
|
|
enable-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
lvds-receiver {
|
|
compatible = "ti,ds90cf384a", "lvds-decoder";
|
|
power-supply = <&vcc_3v3_tft1>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
port@0 {
|
|
reg = <0>;
|
|
lvds_receiver_in: endpoint {
|
|
remote-endpoint = <&lvds0_out>;
|
|
};
|
|
};
|
|
port@1 {
|
|
reg = <1>;
|
|
lvds_receiver_out: endpoint {
|
|
remote-endpoint = <&panel_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
panel {
|
|
compatible = "edt,etm0700g0dh6";
|
|
backlight = <&lcd_backlight>;
|
|
power-supply = <&vcc_3v3_tft1>;
|
|
|
|
port {
|
|
panel_in: endpoint {
|
|
remote-endpoint = <&lvds_receiver_out>;
|
|
};
|
|
};
|
|
};
|
|
|
|
reg_1p5v: 1p5v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "1P5V";
|
|
regulator-min-microvolt = <1500000>;
|
|
regulator-max-microvolt = <1500000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
rsnd_sgtl5000: sound {
|
|
compatible = "simple-audio-card";
|
|
|
|
simple-audio-card,format = "i2s";
|
|
simple-audio-card,bitclock-master = <&sndcodec>;
|
|
simple-audio-card,frame-master = <&sndcodec>;
|
|
|
|
sndcpu: simple-audio-card,cpu {
|
|
sound-dai = <&rcar_sound>;
|
|
};
|
|
|
|
sndcodec: simple-audio-card,codec {
|
|
sound-dai = <&sgtl5000>;
|
|
};
|
|
};
|
|
|
|
vcc_3v3_tft1: regulator-panel {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "vcc-3v3-tft1";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
enable-active-high;
|
|
startup-delay-us = <500>;
|
|
gpio = <&gpio7 25 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
vcc_sdhi1: regulator-vcc-sdhi1 {
|
|
compatible = "regulator-fixed";
|
|
|
|
regulator-name = "SDHI1 Vcc";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpio = <&gpio1 16 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
vccq_sdhi1: regulator-vccq-sdhi1 {
|
|
compatible = "regulator-gpio";
|
|
|
|
regulator-name = "SDHI1 VccQ";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
|
|
gpios-states = <1>;
|
|
states = <3300000 1>, <1800000 0>;
|
|
};
|
|
};
|
|
|
|
&avb {
|
|
pinctrl-0 = <&avb_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
phy-handle = <&phy3>;
|
|
phy-mode = "gmii";
|
|
renesas,no-ether-link;
|
|
status = "okay";
|
|
|
|
phy3: ethernet-phy@3 {
|
|
reg = <3>;
|
|
micrel,led-mode = <1>;
|
|
};
|
|
};
|
|
|
|
&can0 {
|
|
pinctrl-0 = <&can0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&cmt0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&du {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio2 {
|
|
touch-interrupt {
|
|
gpio-hog;
|
|
gpios = <12 GPIO_ACTIVE_LOW>;
|
|
input;
|
|
};
|
|
};
|
|
|
|
&hsusb {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&i2c2 {
|
|
pinctrl-0 = <&i2c2_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
rtc@68 {
|
|
compatible = "ti,bq32000";
|
|
reg = <0x68>;
|
|
};
|
|
|
|
sgtl5000: codec@a {
|
|
compatible = "fsl,sgtl5000";
|
|
#sound-dai-cells = <0>;
|
|
reg = <0x0a>;
|
|
clocks = <&audio_clock>;
|
|
VDDA-supply = <®_3p3v>;
|
|
VDDIO-supply = <®_3p3v>;
|
|
VDDD-supply = <®_1p5v>;
|
|
};
|
|
|
|
touch: touchpanel@38 {
|
|
compatible = "edt,edt-ft5406";
|
|
reg = <0x38>;
|
|
interrupt-parent = <&gpio2>;
|
|
interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
|
|
vcc-supply = <&vcc_3v3_tft1>;
|
|
};
|
|
};
|
|
|
|
&lvds0 {
|
|
status = "okay";
|
|
|
|
ports {
|
|
port@1 {
|
|
lvds0_out: endpoint {
|
|
remote-endpoint = <&lvds_receiver_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci0 {
|
|
pinctrl-0 = <&usb0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pci1 {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb1_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pcie_bus_clk {
|
|
clock-frequency = <100000000>;
|
|
};
|
|
|
|
&pfc {
|
|
can0_pins: can0 {
|
|
groups = "can0_data_d";
|
|
function = "can0";
|
|
};
|
|
|
|
avb_pins: avb {
|
|
groups = "avb_mdio", "avb_gmii";
|
|
function = "avb";
|
|
};
|
|
|
|
i2c2_pins: i2c2 {
|
|
groups = "i2c2";
|
|
function = "i2c2";
|
|
};
|
|
|
|
pwm3_pins: pwm3 {
|
|
groups = "pwm3";
|
|
function = "pwm3";
|
|
};
|
|
|
|
scif0_pins: scif0 {
|
|
groups = "scif0_data_d";
|
|
function = "scif0";
|
|
};
|
|
|
|
scifb1_pins: scifb1 {
|
|
groups = "scifb1_data_d", "scifb1_ctrl";
|
|
function = "scifb1";
|
|
};
|
|
|
|
sdhi1_pins: sd1 {
|
|
groups = "sdhi1_data4", "sdhi1_ctrl";
|
|
function = "sdhi1";
|
|
power-source = <3300>;
|
|
};
|
|
|
|
sdhi1_pins_uhs: sd1_uhs {
|
|
groups = "sdhi1_data4", "sdhi1_ctrl";
|
|
function = "sdhi1";
|
|
power-source = <1800>;
|
|
};
|
|
|
|
sound_pins: sound {
|
|
groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
|
|
function = "ssi";
|
|
};
|
|
|
|
usb0_pins: usb0 {
|
|
groups = "usb0";
|
|
function = "usb0";
|
|
};
|
|
|
|
usb1_pins: usb1 {
|
|
groups = "usb1";
|
|
function = "usb1";
|
|
};
|
|
};
|
|
|
|
&pwm3 {
|
|
pinctrl-0 = <&pwm3_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&rcar_sound {
|
|
pinctrl-0 = <&sound_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
/* Single DAI */
|
|
#sound-dai-cells = <0>;
|
|
|
|
rcar_sound,dai {
|
|
dai0 {
|
|
playback = <&ssi1>, <&src3>, <&dvc1>;
|
|
capture = <&ssi0>, <&src2>, <&dvc0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&rwdt {
|
|
timeout-sec = <60>;
|
|
status = "okay";
|
|
};
|
|
|
|
&scif0 {
|
|
pinctrl-0 = <&scif0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&scifb1 {
|
|
pinctrl-0 = <&scifb1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
uart-has-rtscts;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhi1 {
|
|
pinctrl-0 = <&sdhi1_pins>;
|
|
pinctrl-1 = <&sdhi1_pins_uhs>;
|
|
pinctrl-names = "default", "state_uhs";
|
|
|
|
vmmc-supply = <&vcc_sdhi1>;
|
|
vqmmc-supply = <&vccq_sdhi1>;
|
|
cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
|
|
wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
|
|
sd-uhs-sdr50;
|
|
status = "okay";
|
|
};
|
|
|
|
&ssi1 {
|
|
shared-pin;
|
|
};
|
|
|
|
&usbphy {
|
|
status = "okay";
|
|
};
|