Manivannan Sadhasivam 6340b391e1 arm64: dts: qcom: Remove "iommus" property from PCIe nodes
Currently, most of the Qualcomm SoCs specify both "iommus" and "iommu-map"
properties for the PCIe nodes. First one passes the SMR mask to the iommu
driver and the latter specifies the SID for each PCIe device.

But with "iommus" property, the PCIe controller will be added to the
iommu group along with the devices. This makes no sense because the
controller will not initiate any DMA transaction on its own. And moreover,
it is not strictly required to pass the SMR mask to the iommu driver. If
the "iommus" property is not present, then the default mask of "0" would be
used which should work for all PCIe devices.

On the other side, if the SMR mask specified doesn't match the one expected
by the hypervisor, then all the PCIe transactions will end up triggering
"Unidentified Stream Fault" by the SMMU.

So to get rid of these hassles and also prohibit PCIe controllers from
adding to the iommu group, let's remove the "iommus" property from PCIe
nodes.

Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-arm-msm/20230227195535.GA749409-robh@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308075648.134119-1-manivannan.sadhasivam@linaro.org
2023-04-06 11:32:54 -07:00

4253 lines
106 KiB
Plaintext

// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2020, Linaro Limited
*/
#include <dt-bindings/interconnect/qcom,sm8350.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,dispcc-sm8350.h>
#include <dt-bindings/clock/qcom,gcc-sm8350.h>
#include <dt-bindings/clock/qcom,gpucc-sm8350.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interconnect/qcom,sm8350.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/thermal/thermal.h>
#include <dt-bindings/interconnect/qcom,sm8350.h>
/ {
interrupt-parent = <&intc>;
#address-cells = <2>;
#size-cells = <2>;
chosen { };
clocks {
xo_board: xo-board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <38400000>;
clock-output-names = "xo_board";
};
sleep_clk: sleep-clk {
compatible = "fixed-clock";
clock-frequency = <32000>;
#clock-cells = <0>;
};
};
cpus {
#address-cells = <2>;
#size-cells = <0>;
CPU0: cpu@0 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x0>;
clocks = <&cpufreq_hw 0>;
enable-method = "psci";
next-level-cache = <&L2_0>;
qcom,freq-domain = <&cpufreq_hw 0>;
power-domains = <&CPU_PD0>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_0: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
L3_0: l3-cache {
compatible = "cache";
cache-level = <3>;
};
};
};
CPU1: cpu@100 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x100>;
clocks = <&cpufreq_hw 0>;
enable-method = "psci";
next-level-cache = <&L2_100>;
qcom,freq-domain = <&cpufreq_hw 0>;
power-domains = <&CPU_PD1>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_100: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
CPU2: cpu@200 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x200>;
clocks = <&cpufreq_hw 0>;
enable-method = "psci";
next-level-cache = <&L2_200>;
qcom,freq-domain = <&cpufreq_hw 0>;
power-domains = <&CPU_PD2>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_200: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
CPU3: cpu@300 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x300>;
clocks = <&cpufreq_hw 0>;
enable-method = "psci";
next-level-cache = <&L2_300>;
qcom,freq-domain = <&cpufreq_hw 0>;
power-domains = <&CPU_PD3>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_300: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
CPU4: cpu@400 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x400>;
clocks = <&cpufreq_hw 1>;
enable-method = "psci";
next-level-cache = <&L2_400>;
qcom,freq-domain = <&cpufreq_hw 1>;
power-domains = <&CPU_PD4>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_400: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
CPU5: cpu@500 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x500>;
clocks = <&cpufreq_hw 1>;
enable-method = "psci";
next-level-cache = <&L2_500>;
qcom,freq-domain = <&cpufreq_hw 1>;
power-domains = <&CPU_PD5>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_500: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
CPU6: cpu@600 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x600>;
clocks = <&cpufreq_hw 1>;
enable-method = "psci";
next-level-cache = <&L2_600>;
qcom,freq-domain = <&cpufreq_hw 1>;
power-domains = <&CPU_PD6>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_600: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
CPU7: cpu@700 {
device_type = "cpu";
compatible = "qcom,kryo685";
reg = <0x0 0x700>;
clocks = <&cpufreq_hw 2>;
enable-method = "psci";
next-level-cache = <&L2_700>;
qcom,freq-domain = <&cpufreq_hw 2>;
power-domains = <&CPU_PD7>;
power-domain-names = "psci";
#cooling-cells = <2>;
L2_700: l2-cache {
compatible = "cache";
cache-level = <2>;
next-level-cache = <&L3_0>;
};
};
cpu-map {
cluster0 {
core0 {
cpu = <&CPU0>;
};
core1 {
cpu = <&CPU1>;
};
core2 {
cpu = <&CPU2>;
};
core3 {
cpu = <&CPU3>;
};
core4 {
cpu = <&CPU4>;
};
core5 {
cpu = <&CPU5>;
};
core6 {
cpu = <&CPU6>;
};
core7 {
cpu = <&CPU7>;
};
};
};
idle-states {
entry-method = "psci";
LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
compatible = "arm,idle-state";
idle-state-name = "silver-rail-power-collapse";
arm,psci-suspend-param = <0x40000004>;
entry-latency-us = <355>;
exit-latency-us = <909>;
min-residency-us = <3934>;
local-timer-stop;
};
BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
compatible = "arm,idle-state";
idle-state-name = "gold-rail-power-collapse";
arm,psci-suspend-param = <0x40000004>;
entry-latency-us = <241>;
exit-latency-us = <1461>;
min-residency-us = <4488>;
local-timer-stop;
};
};
domain-idle-states {
CLUSTER_SLEEP_0: cluster-sleep-0 {
compatible = "domain-idle-state";
arm,psci-suspend-param = <0x4100c344>;
entry-latency-us = <3263>;
exit-latency-us = <6562>;
min-residency-us = <9987>;
};
};
};
firmware {
scm: scm {
compatible = "qcom,scm-sm8350", "qcom,scm";
#reset-cells = <1>;
};
};
memory@80000000 {
device_type = "memory";
/* We expect the bootloader to fill in the size */
reg = <0x0 0x80000000 0x0 0x0>;
};
pmu {
compatible = "arm,armv8-pmuv3";
interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
};
psci {
compatible = "arm,psci-1.0";
method = "smc";
CPU_PD0: power-domain-cpu0 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD1: power-domain-cpu1 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD2: power-domain-cpu2 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD3: power-domain-cpu3 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
};
CPU_PD4: power-domain-cpu4 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CPU_PD5: power-domain-cpu5 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CPU_PD6: power-domain-cpu6 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CPU_PD7: power-domain-cpu7 {
#power-domain-cells = <0>;
power-domains = <&CLUSTER_PD>;
domain-idle-states = <&BIG_CPU_SLEEP_0>;
};
CLUSTER_PD: power-domain-cpu-cluster0 {
#power-domain-cells = <0>;
domain-idle-states = <&CLUSTER_SLEEP_0>;
};
};
qup_opp_table_100mhz: opp-table-qup100mhz {
compatible = "operating-points-v2";
opp-50000000 {
opp-hz = /bits/ 64 <50000000>;
required-opps = <&rpmhpd_opp_min_svs>;
};
opp-75000000 {
opp-hz = /bits/ 64 <75000000>;
required-opps = <&rpmhpd_opp_low_svs>;
};
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
required-opps = <&rpmhpd_opp_svs>;
};
};
qup_opp_table_120mhz: opp-table-qup120mhz {
compatible = "operating-points-v2";
opp-50000000 {
opp-hz = /bits/ 64 <50000000>;
required-opps = <&rpmhpd_opp_min_svs>;
};
opp-75000000 {
opp-hz = /bits/ 64 <75000000>;
required-opps = <&rpmhpd_opp_low_svs>;
};
opp-120000000 {
opp-hz = /bits/ 64 <120000000>;
required-opps = <&rpmhpd_opp_svs>;
};
};
reserved_memory: reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
hyp_mem: memory@80000000 {
reg = <0x0 0x80000000 0x0 0x600000>;
no-map;
};
xbl_aop_mem: memory@80700000 {
no-map;
reg = <0x0 0x80700000 0x0 0x160000>;
};
cmd_db: memory@80860000 {
compatible = "qcom,cmd-db";
reg = <0x0 0x80860000 0x0 0x20000>;
no-map;
};
reserved_xbl_uefi_log: memory@80880000 {
reg = <0x0 0x80880000 0x0 0x14000>;
no-map;
};
smem@80900000 {
compatible = "qcom,smem";
reg = <0x0 0x80900000 0x0 0x200000>;
hwlocks = <&tcsr_mutex 3>;
no-map;
};
cpucp_fw_mem: memory@80b00000 {
reg = <0x0 0x80b00000 0x0 0x100000>;
no-map;
};
cdsp_secure_heap: memory@80c00000 {
reg = <0x0 0x80c00000 0x0 0x4600000>;
no-map;
};
pil_camera_mem: mmeory@85200000 {
reg = <0x0 0x85200000 0x0 0x500000>;
no-map;
};
pil_video_mem: memory@85700000 {
reg = <0x0 0x85700000 0x0 0x500000>;
no-map;
};
pil_cvp_mem: memory@85c00000 {
reg = <0x0 0x85c00000 0x0 0x500000>;
no-map;
};
pil_adsp_mem: memory@86100000 {
reg = <0x0 0x86100000 0x0 0x2100000>;
no-map;
};
pil_slpi_mem: memory@88200000 {
reg = <0x0 0x88200000 0x0 0x1500000>;
no-map;
};
pil_cdsp_mem: memory@89700000 {
reg = <0x0 0x89700000 0x0 0x1e00000>;
no-map;
};
pil_ipa_fw_mem: memory@8b500000 {
reg = <0x0 0x8b500000 0x0 0x10000>;
no-map;
};
pil_ipa_gsi_mem: memory@8b510000 {
reg = <0x0 0x8b510000 0x0 0xa000>;
no-map;
};
pil_gpu_mem: memory@8b51a000 {
reg = <0x0 0x8b51a000 0x0 0x2000>;
no-map;
};
pil_spss_mem: memory@8b600000 {
reg = <0x0 0x8b600000 0x0 0x100000>;
no-map;
};
pil_modem_mem: memory@8b800000 {
reg = <0x0 0x8b800000 0x0 0x10000000>;
no-map;
};
rmtfs_mem: memory@9b800000 {
compatible = "qcom,rmtfs-mem";
reg = <0x0 0x9b800000 0x0 0x280000>;
no-map;
qcom,client-id = <1>;
qcom,vmid = <15>;
};
hyp_reserved_mem: memory@d0000000 {
reg = <0x0 0xd0000000 0x0 0x800000>;
no-map;
};
pil_trustedvm_mem: memory@d0800000 {
reg = <0x0 0xd0800000 0x0 0x76f7000>;
no-map;
};
qrtr_shbuf: memory@d7ef7000 {
reg = <0x0 0xd7ef7000 0x0 0x9000>;
no-map;
};
chan0_shbuf: memory@d7f00000 {
reg = <0x0 0xd7f00000 0x0 0x80000>;
no-map;
};
chan1_shbuf: memory@d7f80000 {
reg = <0x0 0xd7f80000 0x0 0x80000>;
no-map;
};
removed_mem: memory@d8800000 {
reg = <0x0 0xd8800000 0x0 0x6800000>;
no-map;
};
};
smp2p-adsp {
compatible = "qcom,smp2p";
qcom,smem = <443>, <429>;
interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <2>;
smp2p_adsp_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_adsp_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
smp2p-cdsp {
compatible = "qcom,smp2p";
qcom,smem = <94>, <432>;
interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <5>;
smp2p_cdsp_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_cdsp_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
smp2p-modem {
compatible = "qcom,smp2p";
qcom,smem = <435>, <428>;
interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <1>;
smp2p_modem_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_modem_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
ipa_smp2p_out: ipa-ap-to-modem {
qcom,entry-name = "ipa";
#qcom,smem-state-cells = <1>;
};
ipa_smp2p_in: ipa-modem-to-ap {
qcom,entry-name = "ipa";
interrupt-controller;
#interrupt-cells = <2>;
};
};
smp2p-slpi {
compatible = "qcom,smp2p";
qcom,smem = <481>, <430>;
interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_SMP2P
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_SMP2P>;
qcom,local-pid = <0>;
qcom,remote-pid = <3>;
smp2p_slpi_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
smp2p_slpi_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
ranges = <0 0 0 0 0x10 0>;
dma-ranges = <0 0 0 0 0x10 0>;
compatible = "simple-bus";
gcc: clock-controller@100000 {
compatible = "qcom,gcc-sm8350";
reg = <0x0 0x00100000 0x0 0x1f0000>;
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
clock-names = "bi_tcxo",
"sleep_clk",
"pcie_0_pipe_clk",
"pcie_1_pipe_clk",
"ufs_card_rx_symbol_0_clk",
"ufs_card_rx_symbol_1_clk",
"ufs_card_tx_symbol_0_clk",
"ufs_phy_rx_symbol_0_clk",
"ufs_phy_rx_symbol_1_clk",
"ufs_phy_tx_symbol_0_clk",
"usb3_phy_wrapper_gcc_usb30_pipe_clk",
"usb3_uni_phy_sec_gcc_usb30_pipe_clk";
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&sleep_clk>,
<&pcie0_phy>,
<&pcie1_phy>,
<0>,
<0>,
<0>,
<&ufs_mem_phy_lanes 0>,
<&ufs_mem_phy_lanes 1>,
<&ufs_mem_phy_lanes 2>,
<&usb_1_qmpphy QMP_USB43DP_USB3_PIPE_CLK>,
<0>;
};
ipcc: mailbox@408000 {
compatible = "qcom,sm8350-ipcc", "qcom,ipcc";
reg = <0 0x00408000 0 0x1000>;
interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <3>;
#mbox-cells = <2>;
};
gpi_dma2: dma-controller@800000 {
compatible = "qcom,sm8350-gpi-dma", "qcom,sm6350-gpi-dma";
reg = <0 0x00800000 0 0x60000>;
interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <12>;
dma-channel-mask = <0xff>;
iommus = <&apps_smmu 0x5f6 0x0>;
#dma-cells = <3>;
status = "disabled";
};
qupv3_id_2: geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x008c0000 0x0 0x6000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
iommus = <&apps_smmu 0x5e3 0x0>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
i2c14: i2c@880000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00880000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c14_default>;
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
<&gpi_dma2 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi14: spi@880000 {
compatible = "qcom,geni-spi";
reg = <0 0x00880000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_120mhz>;
dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
<&gpi_dma2 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c15: i2c@884000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00884000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c15_default>;
interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
<&gpi_dma2 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi15: spi@884000 {
compatible = "qcom,geni-spi";
reg = <0 0x00884000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_120mhz>;
dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
<&gpi_dma2 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c16: i2c@888000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00888000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c16_default>;
interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
<&gpi_dma2 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi16: spi@888000 {
compatible = "qcom,geni-spi";
reg = <0 0x00888000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
<&gpi_dma2 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c17: i2c@88c000 {
compatible = "qcom,geni-i2c";
reg = <0 0x0088c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c17_default>;
interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
<&gpi_dma2 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi17: spi@88c000 {
compatible = "qcom,geni-spi";
reg = <0 0x0088c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
<&gpi_dma2 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
/* QUP no. 18 seems to be strictly SPI/UART-only */
spi18: spi@890000 {
compatible = "qcom,geni-spi";
reg = <0 0x00890000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
<&gpi_dma2 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
uart18: serial@890000 {
compatible = "qcom,geni-uart";
reg = <0 0x00890000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart18_default>;
interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
status = "disabled";
};
i2c19: i2c@894000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00894000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c19_default>;
interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
<&gpi_dma2 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi19: spi@894000 {
compatible = "qcom,geni-spi";
reg = <0 0x00894000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
<&gpi_dma2 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gpi_dma0: dma-controller@900000 {
compatible = "qcom,sm8350-gpi-dma", "qcom,sm6350-gpi-dma";
reg = <0 0x09800000 0 0x60000>;
interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <12>;
dma-channel-mask = <0x7e>;
iommus = <&apps_smmu 0x5b6 0x0>;
#dma-cells = <3>;
status = "disabled";
};
qupv3_id_0: geniqup@9c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x009c0000 0x0 0x6000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
iommus = <&apps_smmu 0x5a3 0>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
i2c0: i2c@980000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00980000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c0_default>;
interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
<&gpi_dma0 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi0: spi@980000 {
compatible = "qcom,geni-spi";
reg = <0 0x00980000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
<&gpi_dma0 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c1: i2c@984000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00984000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c1_default>;
interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
<&gpi_dma0 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi1: spi@984000 {
compatible = "qcom,geni-spi";
reg = <0 0x00984000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
<&gpi_dma0 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c2: i2c@988000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00988000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c2_default>;
interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
<&gpi_dma0 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi2: spi@988000 {
compatible = "qcom,geni-spi";
reg = <0 0x00988000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
<&gpi_dma0 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
uart2: serial@98c000 {
compatible = "qcom,geni-debug-uart";
reg = <0 0x0098c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart3_default_state>;
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
status = "disabled";
};
/* QUP no. 3 seems to be strictly SPI-only */
spi3: spi@98c000 {
compatible = "qcom,geni-spi";
reg = <0 0x0098c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
<&gpi_dma0 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c4: i2c@990000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00990000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c4_default>;
interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
<&gpi_dma0 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi4: spi@990000 {
compatible = "qcom,geni-spi";
reg = <0 0x00990000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
<&gpi_dma0 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c5: i2c@994000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00994000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c5_default>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
<&gpi_dma0 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi5: spi@994000 {
compatible = "qcom,geni-spi";
reg = <0 0x00994000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
<&gpi_dma0 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c6: i2c@998000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00998000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c6_default>;
interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
<&gpi_dma0 1 6 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi6: spi@998000 {
compatible = "qcom,geni-spi";
reg = <0 0x00998000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
<&gpi_dma0 1 6 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
uart6: serial@998000 {
compatible = "qcom,geni-uart";
reg = <0 0x00998000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_uart6_default>;
interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
status = "disabled";
};
i2c7: i2c@99c000 {
compatible = "qcom,geni-i2c";
reg = <0 0x0099c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c7_default>;
interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
<&gpi_dma0 1 7 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi7: spi@99c000 {
compatible = "qcom,geni-spi";
reg = <0 0x0099c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
<&gpi_dma0 1 7 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
gpi_dma1: dma-controller@a00000 {
compatible = "qcom,sm8350-gpi-dma", "qcom,sm6350-gpi-dma";
reg = <0 0x00a00000 0 0x60000>;
interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
dma-channels = <12>;
dma-channel-mask = <0xff>;
iommus = <&apps_smmu 0x56 0x0>;
#dma-cells = <3>;
status = "disabled";
};
qupv3_id_1: geniqup@ac0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x00ac0000 0x0 0x6000>;
clock-names = "m-ahb", "s-ahb";
clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
<&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
iommus = <&apps_smmu 0x43 0>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
status = "disabled";
i2c8: i2c@a80000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a80000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c8_default>;
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
<&gpi_dma1 1 0 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi8: spi@a80000 {
compatible = "qcom,geni-spi";
reg = <0 0x00a80000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_120mhz>;
dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
<&gpi_dma1 1 0 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c9: i2c@a84000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a84000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c9_default>;
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
<&gpi_dma1 1 1 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi9: spi@a84000 {
compatible = "qcom,geni-spi";
reg = <0 0x00a84000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
<&gpi_dma1 1 1 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c10: i2c@a88000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a88000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c10_default>;
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
<&gpi_dma1 1 2 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi10: spi@a88000 {
compatible = "qcom,geni-spi";
reg = <0 0x00a88000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
<&gpi_dma1 1 2 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c11: i2c@a8c000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a8c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c11_default>;
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
<&gpi_dma1 1 3 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi11: spi@a8c000 {
compatible = "qcom,geni-spi";
reg = <0 0x00a8c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
<&gpi_dma1 1 3 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c12: i2c@a90000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a90000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c12_default>;
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
<&gpi_dma1 1 4 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi12: spi@a90000 {
compatible = "qcom,geni-spi";
reg = <0 0x00a90000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
<&gpi_dma1 1 4 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c13: i2c@a94000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00a94000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
pinctrl-names = "default";
pinctrl-0 = <&qup_i2c13_default>;
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
<&gpi_dma1 1 5 QCOM_GPI_I2C>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
spi13: spi@a94000 {
compatible = "qcom,geni-spi";
reg = <0 0x00a94000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&qup_opp_table_100mhz>;
dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
<&gpi_dma1 1 5 QCOM_GPI_SPI>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
rng: rng@10d3000 {
compatible = "qcom,prng-ee";
reg = <0 0x010d3000 0 0x1000>;
clocks = <&rpmhcc RPMH_HWKM_CLK>;
clock-names = "core";
};
config_noc: interconnect@1500000 {
compatible = "qcom,sm8350-config-noc";
reg = <0 0x01500000 0 0xa580>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
mc_virt: interconnect@1580000 {
compatible = "qcom,sm8350-mc-virt";
reg = <0 0x01580000 0 0x1000>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
system_noc: interconnect@1680000 {
compatible = "qcom,sm8350-system-noc";
reg = <0 0x01680000 0 0x1c200>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
aggre1_noc: interconnect@16e0000 {
compatible = "qcom,sm8350-aggre1-noc";
reg = <0 0x016e0000 0 0x1f180>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
aggre2_noc: interconnect@1700000 {
compatible = "qcom,sm8350-aggre2-noc";
reg = <0 0x01700000 0 0x33000>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
mmss_noc: interconnect@1740000 {
compatible = "qcom,sm8350-mmss-noc";
reg = <0 0x01740000 0 0x1f080>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
pcie0: pci@1c00000 {
compatible = "qcom,pcie-sm8350";
reg = <0 0x01c00000 0 0x3000>,
<0 0x60000000 0 0xf1d>,
<0 0x60000f20 0 0xa8>,
<0 0x60001000 0 0x1000>,
<0 0x60100000 0 0x100000>;
reg-names = "parf", "dbi", "elbi", "atu", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
<0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;
interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi0", "msi1", "msi2", "msi3",
"msi4", "msi5", "msi6", "msi7";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
<&gcc GCC_PCIE_0_CFG_AHB_CLK>,
<&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_0_SLV_AXI_CLK>,
<&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
<&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>;
clock-names = "aux",
"cfg",
"bus_master",
"bus_slave",
"slave_q2a",
"tbu",
"ddrss_sf_tbu",
"aggre1",
"aggre0";
iommu-map = <0x0 &apps_smmu 0x1c00 0x1>,
<0x100 &apps_smmu 0x1c01 0x1>;
resets = <&gcc GCC_PCIE_0_BCR>;
reset-names = "pci";
power-domains = <&gcc PCIE_0_GDSC>;
phys = <&pcie0_phy>;
phy-names = "pciephy";
status = "disabled";
};
pcie0_phy: phy@1c06000 {
compatible = "qcom,sm8350-qmp-gen3x1-pcie-phy";
reg = <0 0x01c06000 0 0x2000>;
clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
<&gcc GCC_PCIE_0_CFG_AHB_CLK>,
<&gcc GCC_PCIE_0_CLKREF_EN>,
<&gcc GCC_PCIE0_PHY_RCHNG_CLK>,
<&gcc GCC_PCIE_0_PIPE_CLK>;
clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";
resets = <&gcc GCC_PCIE_0_PHY_BCR>;
reset-names = "phy";
assigned-clocks = <&gcc GCC_PCIE0_PHY_RCHNG_CLK>;
assigned-clock-rates = <100000000>;
#clock-cells = <0>;
clock-output-names = "pcie_0_pipe_clk";
#phy-cells = <0>;
status = "disabled";
};
pcie1: pci@1c08000 {
compatible = "qcom,pcie-sm8350";
reg = <0 0x01c08000 0 0x3000>,
<0 0x40000000 0 0xf1d>,
<0 0x40000f20 0 0xa8>,
<0 0x40001000 0 0x1000>,
<0 0x40100000 0 0x100000>;
reg-names = "parf", "dbi", "elbi", "atu", "config";
device_type = "pci";
linux,pci-domain = <1>;
bus-range = <0x00 0xff>;
num-lanes = <2>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
<0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
<&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_1_SLV_AXI_CLK>,
<&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
<&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
<&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
clock-names = "aux",
"cfg",
"bus_master",
"bus_slave",
"slave_q2a",
"tbu",
"ddrss_sf_tbu",
"aggre1";
iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
<0x100 &apps_smmu 0x1c81 0x1>;
resets = <&gcc GCC_PCIE_1_BCR>;
reset-names = "pci";
power-domains = <&gcc PCIE_1_GDSC>;
phys = <&pcie1_phy>;
phy-names = "pciephy";
status = "disabled";
};
pcie1_phy: phy@1c0f000 {
compatible = "qcom,sm8350-qmp-gen3x2-pcie-phy";
reg = <0 0x01c0e000 0 0x2000>;
clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
<&gcc GCC_PCIE_1_CLKREF_EN>,
<&gcc GCC_PCIE1_PHY_RCHNG_CLK>,
<&gcc GCC_PCIE_1_PIPE_CLK>;
clock-names = "aux", "cfg_ahb", "ref", "rchng", "pipe";
resets = <&gcc GCC_PCIE_1_PHY_BCR>;
reset-names = "phy";
assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
assigned-clock-rates = <100000000>;
#clock-cells = <0>;
clock-output-names = "pcie_1_pipe_clk";
#phy-cells = <0>;
status = "disabled";
};
ufs_mem_hc: ufshc@1d84000 {
compatible = "qcom,sm8350-ufshc", "qcom,ufshc",
"jedec,ufs-2.0";
reg = <0 0x01d84000 0 0x3000>;
interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
phys = <&ufs_mem_phy_lanes>;
phy-names = "ufsphy";
lanes-per-direction = <2>;
#reset-cells = <1>;
resets = <&gcc GCC_UFS_PHY_BCR>;
reset-names = "rst";
power-domains = <&gcc UFS_PHY_GDSC>;
iommus = <&apps_smmu 0xe0 0x0>;
dma-coherent;
clock-names =
"core_clk",
"bus_aggr_clk",
"iface_clk",
"core_clk_unipro",
"ref_clk",
"tx_lane0_sync_clk",
"rx_lane0_sync_clk",
"rx_lane1_sync_clk";
clocks =
<&gcc GCC_UFS_PHY_AXI_CLK>,
<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
<&gcc GCC_UFS_PHY_AHB_CLK>,
<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
freq-table-hz =
<75000000 300000000>,
<0 0>,
<0 0>,
<75000000 300000000>,
<0 0>,
<0 0>,
<0 0>,
<0 0>;
status = "disabled";
};
ufs_mem_phy: phy@1d87000 {
compatible = "qcom,sm8350-qmp-ufs-phy";
reg = <0 0x01d87000 0 0x1c4>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
clock-names = "ref",
"ref_aux";
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
resets = <&ufs_mem_hc 0>;
reset-names = "ufsphy";
status = "disabled";
ufs_mem_phy_lanes: phy@1d87400 {
reg = <0 0x01d87400 0 0x188>,
<0 0x01d87600 0 0x200>,
<0 0x01d87c00 0 0x200>,
<0 0x01d87800 0 0x188>,
<0 0x01d87a00 0 0x200>;
#clock-cells = <1>;
#phy-cells = <0>;
};
};
ipa: ipa@1e40000 {
compatible = "qcom,sm8350-ipa";
iommus = <&apps_smmu 0x5c0 0x0>,
<&apps_smmu 0x5c2 0x0>;
reg = <0 0x01e40000 0 0x8000>,
<0 0x01e50000 0 0x4b20>,
<0 0x01e04000 0 0x23000>;
reg-names = "ipa-reg",
"ipa-shared",
"gsi";
interrupts-extended = <&intc GIC_SPI 655 IRQ_TYPE_EDGE_RISING>,
<&intc GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>,
<&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
<&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "ipa",
"gsi",
"ipa-clock-query",
"ipa-setup-ready";
clocks = <&rpmhcc RPMH_IPA_CLK>;
clock-names = "core";
interconnects = <&aggre2_noc MASTER_IPA 0 &mc_virt SLAVE_EBI1 0>,
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_IPA_CFG 0>;
interconnect-names = "memory",
"config";
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&ipa_smp2p_out 0>,
<&ipa_smp2p_out 1>;
qcom,smem-state-names = "ipa-clock-enabled-valid",
"ipa-clock-enabled";
status = "disabled";
};
tcsr_mutex: hwlock@1f40000 {
compatible = "qcom,tcsr-mutex";
reg = <0x0 0x01f40000 0x0 0x40000>;
#hwlock-cells = <1>;
};
gpu: gpu@3d00000 {
compatible = "qcom,adreno-660.1", "qcom,adreno";
reg = <0 0x03d00000 0 0x40000>,
<0 0x03d9e000 0 0x1000>,
<0 0x03d61000 0 0x800>;
reg-names = "kgsl_3d0_reg_memory",
"cx_mem",
"cx_dbgc";
interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
iommus = <&adreno_smmu 0 0x400>, <&adreno_smmu 1 0x400>;
operating-points-v2 = <&gpu_opp_table>;
qcom,gmu = <&gmu>;
status = "disabled";
zap-shader {
memory-region = <&pil_gpu_mem>;
};
/* note: downstream checks gpu binning for 670 Mhz */
gpu_opp_table: opp-table {
compatible = "operating-points-v2";
opp-840000000 {
opp-hz = /bits/ 64 <840000000>;
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
};
opp-778000000 {
opp-hz = /bits/ 64 <778000000>;
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
};
opp-738000000 {
opp-hz = /bits/ 64 <738000000>;
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
};
opp-676000000 {
opp-hz = /bits/ 64 <676000000>;
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
};
opp-608000000 {
opp-hz = /bits/ 64 <608000000>;
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
};
opp-540000000 {
opp-hz = /bits/ 64 <540000000>;
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
};
opp-491000000 {
opp-hz = /bits/ 64 <491000000>;
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>;
};
opp-443000000 {
opp-hz = /bits/ 64 <443000000>;
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
};
opp-379000000 {
opp-hz = /bits/ 64 <379000000>;
opp-level = <80 /* RPMH_REGULATOR_LEVEL_LOW_SVS_L1 */>;
};
opp-315000000 {
opp-hz = /bits/ 64 <315000000>;
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
};
};
};
gmu: gmu@3d6a000 {
compatible = "qcom,adreno-gmu-660.1", "qcom,adreno-gmu";
reg = <0 0x03d6a000 0 0x34000>,
<0 0x03de0000 0 0x10000>,
<0 0x0b290000 0 0x10000>;
reg-names = "gmu", "rscc", "gmu_pdc";
interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "hfi", "gmu";
clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
<&gpucc GPU_CC_CXO_CLK>,
<&gcc GCC_DDRSS_GPU_AXI_CLK>,
<&gcc GCC_GPU_MEMNOC_GFX_CLK>,
<&gpucc GPU_CC_AHB_CLK>,
<&gpucc GPU_CC_HUB_CX_INT_CLK>,
<&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>;
clock-names = "gmu",
"cxo",
"axi",
"memnoc",
"ahb",
"hub",
"smmu_vote";
power-domains = <&gpucc GPU_CX_GDSC>,
<&gpucc GPU_GX_GDSC>;
power-domain-names = "cx",
"gx";
iommus = <&adreno_smmu 5 0x400>;
operating-points-v2 = <&gmu_opp_table>;
gmu_opp_table: opp-table {
compatible = "operating-points-v2";
opp-200000000 {
opp-hz = /bits/ 64 <200000000>;
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
};
};
};
gpucc: clock-controller@3d90000 {
compatible = "qcom,sm8350-gpucc";
reg = <0 0x03d90000 0 0x9000>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_GPU_GPLL0_CLK_SRC>,
<&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
clock-names = "bi_tcxo",
"gcc_gpu_gpll0_clk_src",
"gcc_gpu_gpll0_div_clk_src";
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
};
adreno_smmu: iommu@3da0000 {
compatible = "qcom,sm8350-smmu-500", "qcom,adreno-smmu",
"qcom,smmu-500", "arm,mmu-500";
reg = <0 0x03da0000 0 0x20000>;
#iommu-cells = <2>;
#global-interrupts = <2>;
interrupts = <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
<&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
<&gpucc GPU_CC_AHB_CLK>,
<&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>,
<&gpucc GPU_CC_CX_GMU_CLK>,
<&gpucc GPU_CC_HUB_CX_INT_CLK>,
<&gpucc GPU_CC_HUB_AON_CLK>;
clock-names = "bus",
"iface",
"ahb",
"hlos1_vote_gpu_smmu",
"cx_gmu",
"hub_cx_int",
"hub_aon";
power-domains = <&gpucc GPU_CX_GDSC>;
dma-coherent;
};
lpass_ag_noc: interconnect@3c40000 {
compatible = "qcom,sm8350-lpass-ag-noc";
reg = <0 0x03c40000 0 0xf080>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
mpss: remoteproc@4080000 {
compatible = "qcom,sm8350-mpss-pas";
reg = <0x0 0x04080000 0x0 0x4040>;
interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
<&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
<&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready", "handover",
"stop-ack", "shutdown-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8350_CX>,
<&rpmhpd SM8350_MSS>;
power-domain-names = "cx", "mss";
interconnects = <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
memory-region = <&pil_modem_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_modem_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_MPSS
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "modem";
qcom,remote-pid = <1>;
};
};
slpi: remoteproc@5c00000 {
compatible = "qcom,sm8350-slpi-pas";
reg = <0 0x05c00000 0 0x4000>;
interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
<&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8350_LCX>,
<&rpmhpd SM8350_LMX>;
power-domain-names = "lcx", "lmx";
memory-region = <&pil_slpi_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_slpi_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_SLPI
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "slpi";
qcom,remote-pid = <3>;
fastrpc {
compatible = "qcom,fastrpc";
qcom,glink-channels = "fastrpcglink-apps-dsp";
label = "sdsp";
qcom,non-secure-domain;
#address-cells = <1>;
#size-cells = <0>;
compute-cb@1 {
compatible = "qcom,fastrpc-compute-cb";
reg = <1>;
iommus = <&apps_smmu 0x0541 0x0>;
};
compute-cb@2 {
compatible = "qcom,fastrpc-compute-cb";
reg = <2>;
iommus = <&apps_smmu 0x0542 0x0>;
};
compute-cb@3 {
compatible = "qcom,fastrpc-compute-cb";
reg = <3>;
iommus = <&apps_smmu 0x0543 0x0>;
/* note: shared-cb = <4> in downstream */
};
};
};
};
sdhc_2: mmc@8804000 {
compatible = "qcom,sm8350-sdhci", "qcom,sdhci-msm-v5";
reg = <0 0x08804000 0 0x1000>;
interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "hc_irq", "pwr_irq";
clocks = <&gcc GCC_SDCC2_AHB_CLK>,
<&gcc GCC_SDCC2_APPS_CLK>,
<&rpmhcc RPMH_CXO_CLK>;
clock-names = "iface", "core", "xo";
resets = <&gcc GCC_SDCC2_BCR>;
interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
interconnect-names = "sdhc-ddr","cpu-sdhc";
iommus = <&apps_smmu 0x4a0 0x0>;
power-domains = <&rpmhpd SM8350_CX>;
operating-points-v2 = <&sdhc2_opp_table>;
bus-width = <4>;
dma-coherent;
status = "disabled";
sdhc2_opp_table: opp-table {
compatible = "operating-points-v2";
opp-100000000 {
opp-hz = /bits/ 64 <100000000>;
required-opps = <&rpmhpd_opp_low_svs>;
};
opp-202000000 {
opp-hz = /bits/ 64 <202000000>;
required-opps = <&rpmhpd_opp_svs_l1>;
};
};
};
usb_1_hsphy: phy@88e3000 {
compatible = "qcom,sm8350-usb-hs-phy",
"qcom,usb-snps-hs-7nm-phy";
reg = <0 0x088e3000 0 0x400>;
status = "disabled";
#phy-cells = <0>;
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
};
usb_2_hsphy: phy@88e4000 {
compatible = "qcom,sm8250-usb-hs-phy",
"qcom,usb-snps-hs-7nm-phy";
reg = <0 0x088e4000 0 0x400>;
status = "disabled";
#phy-cells = <0>;
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "ref";
resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
};
usb_1_qmpphy: phy@88e9000 {
compatible = "qcom,sm8350-qmp-usb3-dp-phy";
reg = <0 0x088e8000 0 0x3000>;
clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
<&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
clock-names = "aux", "ref", "com_aux", "usb3_pipe";
resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
<&gcc GCC_USB3_PHY_PRIM_BCR>;
reset-names = "phy", "common";
#clock-cells = <1>;
#phy-cells = <1>;
status = "disabled";
};
usb_2_qmpphy: phy-wrapper@88eb000 {
compatible = "qcom,sm8350-qmp-usb3-uni-phy";
reg = <0 0x088eb000 0 0x200>;
status = "disabled";
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
<&rpmhcc RPMH_CXO_CLK>,
<&gcc GCC_USB3_SEC_CLKREF_EN>,
<&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
clock-names = "aux", "ref_clk_src", "ref", "com_aux";
resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>,
<&gcc GCC_USB3_PHY_SEC_BCR>;
reset-names = "phy", "common";
usb_2_ssphy: phy@88ebe00 {
reg = <0 0x088ebe00 0 0x200>,
<0 0x088ec000 0 0x200>,
<0 0x088eb200 0 0x1100>;
#phy-cells = <0>;
#clock-cells = <0>;
clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
clock-names = "pipe0";
clock-output-names = "usb3_uni_phy_pipe_clk_src";
};
};
dc_noc: interconnect@90c0000 {
compatible = "qcom,sm8350-dc-noc";
reg = <0 0x090c0000 0 0x4200>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
gem_noc: interconnect@9100000 {
compatible = "qcom,sm8350-gem-noc";
reg = <0 0x09100000 0 0xb4000>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
system-cache-controller@9200000 {
compatible = "qcom,sm8350-llcc";
reg = <0 0x09200000 0 0x58000>, <0 0x09280000 0 0x58000>,
<0 0x09300000 0 0x58000>, <0 0x09380000 0 0x58000>,
<0 0x09600000 0 0x58000>;
reg-names = "llcc0_base", "llcc1_base", "llcc2_base",
"llcc3_base", "llcc_broadcast_base";
};
compute_noc: interconnect@a0c0000 {
compatible = "qcom,sm8350-compute-noc";
reg = <0 0x0a0c0000 0 0xa180>;
#interconnect-cells = <2>;
qcom,bcm-voters = <&apps_bcm_voter>;
};
usb_1: usb@a6f8800 {
compatible = "qcom,sm8350-dwc3", "qcom,dwc3";
reg = <0 0x0a6f8800 0 0x400>;
status = "disabled";
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
<&gcc GCC_USB30_PRIM_MASTER_CLK>,
<&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
<&gcc GCC_USB30_PRIM_SLEEP_CLK>,
<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
clock-names = "cfg_noc",
"core",
"iface",
"sleep",
"mock_utmi";
assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
<&gcc GCC_USB30_PRIM_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 15 IRQ_TYPE_EDGE_BOTH>,
<&pdc 14 IRQ_TYPE_EDGE_BOTH>;
interrupt-names = "hs_phy_irq",
"ss_phy_irq",
"dm_hs_phy_irq",
"dp_hs_phy_irq";
power-domains = <&gcc USB30_PRIM_GDSC>;
resets = <&gcc GCC_USB30_PRIM_BCR>;
usb_1_dwc3: usb@a600000 {
compatible = "snps,dwc3";
reg = <0 0x0a600000 0 0xcd00>;
interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
iommus = <&apps_smmu 0x0 0x0>;
snps,dis_u2_susphy_quirk;
snps,dis_enblslpm_quirk;
phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
phy-names = "usb2-phy", "usb3-phy";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
usb_1_dwc3_hs: endpoint {
};
};
port@1 {
reg = <1>;
usb_1_dwc3_ss: endpoint {
};
};
};
};
};
usb_2: usb@a8f8800 {
compatible = "qcom,sm8350-dwc3", "qcom,dwc3";
reg = <0 0x0a8f8800 0 0x400>;
status = "disabled";
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
<&gcc GCC_USB30_SEC_MASTER_CLK>,
<&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
<&gcc GCC_USB30_SEC_SLEEP_CLK>,
<&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
<&gcc GCC_USB3_SEC_CLKREF_EN>;
clock-names = "cfg_noc",
"core",
"iface",
"sleep",
"mock_utmi",
"xo";
assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
<&gcc GCC_USB30_SEC_MASTER_CLK>;
assigned-clock-rates = <19200000>, <200000000>;
interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 13 IRQ_TYPE_EDGE_BOTH>,
<&pdc 12 IRQ_TYPE_EDGE_BOTH>;
interrupt-names = "hs_phy_irq",
"ss_phy_irq",
"dm_hs_phy_irq",
"dp_hs_phy_irq";
power-domains = <&gcc USB30_SEC_GDSC>;
resets = <&gcc GCC_USB30_SEC_BCR>;
usb_2_dwc3: usb@a800000 {
compatible = "snps,dwc3";
reg = <0 0x0a800000 0 0xcd00>;
interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
iommus = <&apps_smmu 0x20 0x0>;
snps,dis_u2_susphy_quirk;
snps,dis_enblslpm_quirk;
phys = <&usb_2_hsphy>, <&usb_2_ssphy>;
phy-names = "usb2-phy", "usb3-phy";
};
};
mdss: display-subsystem@ae00000 {
compatible = "qcom,sm8350-mdss";
reg = <0 0x0ae00000 0 0x1000>;
reg-names = "mdss";
interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
<&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
interconnect-names = "mdp0-mem", "mdp1-mem";
power-domains = <&dispcc MDSS_GDSC>;
resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
<&gcc GCC_DISP_HF_AXI_CLK>,
<&gcc GCC_DISP_SF_AXI_CLK>,
<&dispcc DISP_CC_MDSS_MDP_CLK>;
clock-names = "iface", "bus", "nrt_bus", "core";
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <1>;
iommus = <&apps_smmu 0x820 0x402>;
status = "disabled";
#address-cells = <2>;
#size-cells = <2>;
ranges;
dpu_opp_table: opp-table {
compatible = "operating-points-v2";
/* TODO: opp-200000000 should work with
* &rpmhpd_opp_low_svs, but one some of
* sm8350_hdk boards reboot using this
* opp.
*/
opp-200000000 {
opp-hz = /bits/ 64 <200000000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-300000000 {
opp-hz = /bits/ 64 <300000000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-345000000 {
opp-hz = /bits/ 64 <345000000>;
required-opps = <&rpmhpd_opp_svs_l1>;
};
opp-460000000 {
opp-hz = /bits/ 64 <460000000>;
required-opps = <&rpmhpd_opp_nom>;
};
};
mdss_mdp: display-controller@ae01000 {
compatible = "qcom,sm8350-dpu";
reg = <0 0x0ae01000 0 0x8f000>,
<0 0x0aeb0000 0 0x2008>;
reg-names = "mdp", "vbif";
clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
<&gcc GCC_DISP_SF_AXI_CLK>,
<&dispcc DISP_CC_MDSS_AHB_CLK>,
<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
<&dispcc DISP_CC_MDSS_MDP_CLK>,
<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
clock-names = "bus",
"nrt_bus",
"iface",
"lut",
"core",
"vsync";
assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
assigned-clock-rates = <19200000>;
operating-points-v2 = <&dpu_opp_table>;
power-domains = <&rpmhpd SM8350_MMCX>;
interrupt-parent = <&mdss>;
interrupts = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
dpu_intf1_out: endpoint {
remote-endpoint = <&mdss_dsi0_in>;
};
};
port@1 {
reg = <1>;
dpu_intf2_out: endpoint {
remote-endpoint = <&mdss_dsi1_in>;
};
};
port@2 {
reg = <2>;
dpu_intf0_out: endpoint {
remote-endpoint = <&mdss_dp_in>;
};
};
};
};
mdss_dp: displayport-controller@ae90000 {
compatible = "qcom,sm8350-dp";
reg = <0 0xae90000 0 0x200>,
<0 0xae90200 0 0x200>,
<0 0xae90400 0 0x600>,
<0 0xae91000 0 0x400>,
<0 0xae91400 0 0x400>;
interrupt-parent = <&mdss>;
interrupts = <12>;
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
<&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
<&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
<&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
<&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
clock-names = "core_iface",
"core_aux",
"ctrl_link",
"ctrl_link_iface",
"stream_pixel";
assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
<&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
<&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
phy-names = "dp";
#sound-dai-cells = <0>;
operating-points-v2 = <&dp_opp_table>;
power-domains = <&rpmhpd SM8350_MMCX>;
status = "disabled";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
mdss_dp_in: endpoint {
remote-endpoint = <&dpu_intf0_out>;
};
};
};
dp_opp_table: opp-table {
compatible = "operating-points-v2";
opp-160000000 {
opp-hz = /bits/ 64 <160000000>;
required-opps = <&rpmhpd_opp_low_svs>;
};
opp-270000000 {
opp-hz = /bits/ 64 <270000000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-540000000 {
opp-hz = /bits/ 64 <540000000>;
required-opps = <&rpmhpd_opp_svs_l1>;
};
opp-810000000 {
opp-hz = /bits/ 64 <810000000>;
required-opps = <&rpmhpd_opp_nom>;
};
};
};
mdss_dsi0: dsi@ae94000 {
compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
reg = <0 0x0ae94000 0 0x400>;
reg-names = "dsi_ctrl";
interrupt-parent = <&mdss>;
interrupts = <4>;
clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
<&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
<&dispcc DISP_CC_MDSS_PCLK0_CLK>,
<&dispcc DISP_CC_MDSS_ESC0_CLK>,
<&dispcc DISP_CC_MDSS_AHB_CLK>,
<&gcc GCC_DISP_HF_AXI_CLK>;
clock-names = "byte",
"byte_intf",
"pixel",
"core",
"iface",
"bus";
assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
<&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
assigned-clock-parents = <&mdss_dsi0_phy 0>,
<&mdss_dsi0_phy 1>;
operating-points-v2 = <&dsi0_opp_table>;
power-domains = <&rpmhpd SM8350_MMCX>;
phys = <&mdss_dsi0_phy>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
dsi0_opp_table: opp-table {
compatible = "operating-points-v2";
/* TODO: opp-187500000 should work with
* &rpmhpd_opp_low_svs, but one some of
* sm8350_hdk boards reboot using this
* opp.
*/
opp-187500000 {
opp-hz = /bits/ 64 <187500000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-300000000 {
opp-hz = /bits/ 64 <300000000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-358000000 {
opp-hz = /bits/ 64 <358000000>;
required-opps = <&rpmhpd_opp_svs_l1>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
mdss_dsi0_in: endpoint {
remote-endpoint = <&dpu_intf1_out>;
};
};
port@1 {
reg = <1>;
mdss_dsi0_out: endpoint {
};
};
};
};
mdss_dsi0_phy: phy@ae94400 {
compatible = "qcom,sm8350-dsi-phy-5nm";
reg = <0 0x0ae94400 0 0x200>,
<0 0x0ae94600 0 0x280>,
<0 0x0ae94900 0 0x27c>;
reg-names = "dsi_phy",
"dsi_phy_lane",
"dsi_pll";
#clock-cells = <1>;
#phy-cells = <0>;
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
<&rpmhcc RPMH_CXO_CLK>;
clock-names = "iface", "ref";
status = "disabled";
};
mdss_dsi1: dsi@ae96000 {
compatible = "qcom,sm8350-dsi-ctrl", "qcom,mdss-dsi-ctrl";
reg = <0 0x0ae96000 0 0x400>;
reg-names = "dsi_ctrl";
interrupt-parent = <&mdss>;
interrupts = <5>;
clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
<&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
<&dispcc DISP_CC_MDSS_PCLK1_CLK>,
<&dispcc DISP_CC_MDSS_ESC1_CLK>,
<&dispcc DISP_CC_MDSS_AHB_CLK>,
<&gcc GCC_DISP_HF_AXI_CLK>;
clock-names = "byte",
"byte_intf",
"pixel",
"core",
"iface",
"bus";
assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
<&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
assigned-clock-parents = <&mdss_dsi1_phy 0>,
<&mdss_dsi1_phy 1>;
operating-points-v2 = <&dsi1_opp_table>;
power-domains = <&rpmhpd SM8350_MMCX>;
phys = <&mdss_dsi1_phy>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
dsi1_opp_table: opp-table {
compatible = "operating-points-v2";
/* TODO: opp-187500000 should work with
* &rpmhpd_opp_low_svs, but one some of
* sm8350_hdk boards reboot using this
* opp.
*/
opp-187500000 {
opp-hz = /bits/ 64 <187500000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-300000000 {
opp-hz = /bits/ 64 <300000000>;
required-opps = <&rpmhpd_opp_svs>;
};
opp-358000000 {
opp-hz = /bits/ 64 <358000000>;
required-opps = <&rpmhpd_opp_svs_l1>;
};
};
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
mdss_dsi1_in: endpoint {
remote-endpoint = <&dpu_intf2_out>;
};
};
port@1 {
reg = <1>;
mdss_dsi1_out: endpoint {
};
};
};
};
mdss_dsi1_phy: phy@ae96400 {
compatible = "qcom,sm8350-dsi-phy-5nm";
reg = <0 0x0ae96400 0 0x200>,
<0 0x0ae96600 0 0x280>,
<0 0x0ae96900 0 0x27c>;
reg-names = "dsi_phy",
"dsi_phy_lane",
"dsi_pll";
#clock-cells = <1>;
#phy-cells = <0>;
clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
<&rpmhcc RPMH_CXO_CLK>;
clock-names = "iface", "ref";
status = "disabled";
};
};
dispcc: clock-controller@af00000 {
compatible = "qcom,sm8350-dispcc";
reg = <0 0x0af00000 0 0x10000>;
clocks = <&rpmhcc RPMH_CXO_CLK>,
<&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>,
<&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>,
<&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
<&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
clock-names = "bi_tcxo",
"dsi0_phy_pll_out_byteclk",
"dsi0_phy_pll_out_dsiclk",
"dsi1_phy_pll_out_byteclk",
"dsi1_phy_pll_out_dsiclk",
"dp_phy_pll_link_clk",
"dp_phy_pll_vco_div_clk";
#clock-cells = <1>;
#reset-cells = <1>;
#power-domain-cells = <1>;
power-domains = <&rpmhpd SM8350_MMCX>;
};
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm8350-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>,
<59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>,
<69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>,
<156 716 12>;
#interrupt-cells = <2>;
interrupt-parent = <&intc>;
interrupt-controller;
};
tsens0: thermal-sensor@c263000 {
compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
reg = <0 0x0c263000 0 0x1ff>, /* TM */
<0 0x0c222000 0 0x8>; /* SROT */
#qcom,sensors = <15>;
interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow", "critical";
#thermal-sensor-cells = <1>;
};
tsens1: thermal-sensor@c265000 {
compatible = "qcom,sm8350-tsens", "qcom,tsens-v2";
reg = <0 0x0c265000 0 0x1ff>, /* TM */
<0 0x0c223000 0 0x8>; /* SROT */
#qcom,sensors = <14>;
interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
<&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow", "critical";
#thermal-sensor-cells = <1>;
};
aoss_qmp: power-management@c300000 {
compatible = "qcom,sm8350-aoss-qmp", "qcom,aoss-qmp";
reg = <0 0x0c300000 0 0x400>;
interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
#clock-cells = <0>;
};
sram@c3f0000 {
compatible = "qcom,rpmh-stats";
reg = <0 0x0c3f0000 0 0x400>;
};
spmi_bus: spmi@c440000 {
compatible = "qcom,spmi-pmic-arb";
reg = <0x0 0x0c440000 0x0 0x1100>,
<0x0 0x0c600000 0x0 0x2000000>,
<0x0 0x0e600000 0x0 0x100000>,
<0x0 0x0e700000 0x0 0xa0000>,
<0x0 0x0c40a000 0x0 0x26000>;
reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
interrupt-names = "periph_irq";
interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
qcom,ee = <0>;
qcom,channel = <0>;
#address-cells = <2>;
#size-cells = <0>;
interrupt-controller;
#interrupt-cells = <4>;
};
tlmm: pinctrl@f100000 {
compatible = "qcom,sm8350-tlmm";
reg = <0 0x0f100000 0 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
gpio-ranges = <&tlmm 0 0 204>;
wakeup-parent = <&pdc>;
sdc2_default_state: sdc2-default-state {
clk-pins {
pins = "sdc2_clk";
drive-strength = <16>;
bias-disable;
};
cmd-pins {
pins = "sdc2_cmd";
drive-strength = <16>;
bias-pull-up;
};
data-pins {
pins = "sdc2_data";
drive-strength = <16>;
bias-pull-up;
};
};
sdc2_sleep_state: sdc2-sleep-state {
clk-pins {
pins = "sdc2_clk";
drive-strength = <2>;
bias-disable;
};
cmd-pins {
pins = "sdc2_cmd";
drive-strength = <2>;
bias-pull-up;
};
data-pins {
pins = "sdc2_data";
drive-strength = <2>;
bias-pull-up;
};
};
qup_uart3_default_state: qup-uart3-default-state {
rx-pins {
pins = "gpio18";
function = "qup3";
};
tx-pins {
pins = "gpio19";
function = "qup3";
};
};
qup_uart6_default: qup-uart6-default-state {
pins = "gpio30", "gpio31";
function = "qup6";
drive-strength = <2>;
bias-disable;
};
qup_uart18_default: qup-uart18-default-state {
pins = "gpio58", "gpio59";
function = "qup18";
drive-strength = <2>;
bias-disable;
};
qup_i2c0_default: qup-i2c0-default-state {
pins = "gpio4", "gpio5";
function = "qup0";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c1_default: qup-i2c1-default-state {
pins = "gpio8", "gpio9";
function = "qup1";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c2_default: qup-i2c2-default-state {
pins = "gpio12", "gpio13";
function = "qup2";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c4_default: qup-i2c4-default-state {
pins = "gpio20", "gpio21";
function = "qup4";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c5_default: qup-i2c5-default-state {
pins = "gpio24", "gpio25";
function = "qup5";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c6_default: qup-i2c6-default-state {
pins = "gpio28", "gpio29";
function = "qup6";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c7_default: qup-i2c7-default-state {
pins = "gpio32", "gpio33";
function = "qup7";
drive-strength = <2>;
bias-disable;
};
qup_i2c8_default: qup-i2c8-default-state {
pins = "gpio36", "gpio37";
function = "qup8";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c9_default: qup-i2c9-default-state {
pins = "gpio40", "gpio41";
function = "qup9";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c10_default: qup-i2c10-default-state {
pins = "gpio44", "gpio45";
function = "qup10";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c11_default: qup-i2c11-default-state {
pins = "gpio48", "gpio49";
function = "qup11";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c12_default: qup-i2c12-default-state {
pins = "gpio52", "gpio53";
function = "qup12";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c13_default: qup-i2c13-default-state {
pins = "gpio0", "gpio1";
function = "qup13";
drive-strength = <2>;
bias-pull-up;
};
qup_i2c14_default: qup-i2c14-default-state {
pins = "gpio56", "gpio57";
function = "qup14";
drive-strength = <2>;
bias-disable;
};
qup_i2c15_default: qup-i2c15-default-state {
pins = "gpio60", "gpio61";
function = "qup15";
drive-strength = <2>;
bias-disable;
};
qup_i2c16_default: qup-i2c16-default-state {
pins = "gpio64", "gpio65";
function = "qup16";
drive-strength = <2>;
bias-disable;
};
qup_i2c17_default: qup-i2c17-default-state {
pins = "gpio72", "gpio73";
function = "qup17";
drive-strength = <2>;
bias-disable;
};
qup_i2c19_default: qup-i2c19-default-state {
pins = "gpio76", "gpio77";
function = "qup19";
drive-strength = <2>;
bias-disable;
};
};
apps_smmu: iommu@15000000 {
compatible = "qcom,sm8350-smmu-500", "arm,mmu-500";
reg = <0 0x15000000 0 0x100000>;
#iommu-cells = <2>;
#global-interrupts = <2>;
interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>;
};
adsp: remoteproc@17300000 {
compatible = "qcom,sm8350-adsp-pas";
reg = <0 0x17300000 0 0x100>;
interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
<&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8350_LCX>,
<&rpmhpd SM8350_LMX>;
power-domain-names = "lcx", "lmx";
memory-region = <&pil_adsp_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_adsp_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_LPASS
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "lpass";
qcom,remote-pid = <2>;
fastrpc {
compatible = "qcom,fastrpc";
qcom,glink-channels = "fastrpcglink-apps-dsp";
label = "adsp";
qcom,non-secure-domain;
#address-cells = <1>;
#size-cells = <0>;
compute-cb@3 {
compatible = "qcom,fastrpc-compute-cb";
reg = <3>;
iommus = <&apps_smmu 0x1803 0x0>;
};
compute-cb@4 {
compatible = "qcom,fastrpc-compute-cb";
reg = <4>;
iommus = <&apps_smmu 0x1804 0x0>;
};
compute-cb@5 {
compatible = "qcom,fastrpc-compute-cb";
reg = <5>;
iommus = <&apps_smmu 0x1805 0x0>;
};
};
};
};
intc: interrupt-controller@17a00000 {
compatible = "arm,gic-v3";
#interrupt-cells = <3>;
interrupt-controller;
#redistributor-regions = <1>;
redistributor-stride = <0 0x20000>;
reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */
<0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
};
timer@17c20000 {
compatible = "arm,armv7-timer-mem";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0 0x20000000>;
reg = <0x0 0x17c20000 0x0 0x1000>;
clock-frequency = <19200000>;
frame@17c21000 {
frame-number = <0>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c21000 0x1000>,
<0x17c22000 0x1000>;
};
frame@17c23000 {
frame-number = <1>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c23000 0x1000>;
status = "disabled";
};
frame@17c25000 {
frame-number = <2>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c25000 0x1000>;
status = "disabled";
};
frame@17c27000 {
frame-number = <3>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c27000 0x1000>;
status = "disabled";
};
frame@17c29000 {
frame-number = <4>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c29000 0x1000>;
status = "disabled";
};
frame@17c2b000 {
frame-number = <5>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c2b000 0x1000>;
status = "disabled";
};
frame@17c2d000 {
frame-number = <6>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x17c2d000 0x1000>;
status = "disabled";
};
};
apps_rsc: rsc@18200000 {
label = "apps_rsc";
compatible = "qcom,rpmh-rsc";
reg = <0x0 0x18200000 0x0 0x10000>,
<0x0 0x18210000 0x0 0x10000>,
<0x0 0x18220000 0x0 0x10000>;
reg-names = "drv-0", "drv-1", "drv-2";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
qcom,tcs-offset = <0xd00>;
qcom,drv-id = <2>;
qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
<WAKE_TCS 3>, <CONTROL_TCS 0>;
power-domains = <&CLUSTER_PD>;
rpmhcc: clock-controller {
compatible = "qcom,sm8350-rpmh-clk";
#clock-cells = <1>;
clock-names = "xo";
clocks = <&xo_board>;
};
rpmhpd: power-controller {
compatible = "qcom,sm8350-rpmhpd";
#power-domain-cells = <1>;
operating-points-v2 = <&rpmhpd_opp_table>;
rpmhpd_opp_table: opp-table {
compatible = "operating-points-v2";
rpmhpd_opp_ret: opp1 {
opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
};
rpmhpd_opp_min_svs: opp2 {
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
};
rpmhpd_opp_low_svs: opp3 {
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
};
rpmhpd_opp_svs: opp4 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
};
rpmhpd_opp_svs_l1: opp5 {
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
};
rpmhpd_opp_nom: opp6 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
};
rpmhpd_opp_nom_l1: opp7 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
};
rpmhpd_opp_nom_l2: opp8 {
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
};
rpmhpd_opp_turbo: opp9 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
};
rpmhpd_opp_turbo_l1: opp10 {
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
};
};
};
apps_bcm_voter: bcm-voter {
compatible = "qcom,bcm-voter";
};
};
cpufreq_hw: cpufreq@18591000 {
compatible = "qcom,sm8350-cpufreq-epss", "qcom,cpufreq-epss";
reg = <0 0x18591000 0 0x1000>,
<0 0x18592000 0 0x1000>,
<0 0x18593000 0 0x1000>;
reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
clock-names = "xo", "alternate";
#freq-domain-cells = <1>;
#clock-cells = <1>;
};
cdsp: remoteproc@98900000 {
compatible = "qcom,sm8350-cdsp-pas";
reg = <0 0x98900000 0 0x1400000>;
interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
<&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
<&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "wdog", "fatal", "ready",
"handover", "stop-ack";
clocks = <&rpmhcc RPMH_CXO_CLK>;
clock-names = "xo";
power-domains = <&rpmhpd SM8350_CX>,
<&rpmhpd SM8350_MXC>;
power-domain-names = "cx", "mxc";
interconnects = <&compute_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;
memory-region = <&pil_cdsp_mem>;
qcom,qmp = <&aoss_qmp>;
qcom,smem-states = <&smp2p_cdsp_out 0>;
qcom,smem-state-names = "stop";
status = "disabled";
glink-edge {
interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_GLINK_QMP
IRQ_TYPE_EDGE_RISING>;
mboxes = <&ipcc IPCC_CLIENT_CDSP
IPCC_MPROC_SIGNAL_GLINK_QMP>;
label = "cdsp";
qcom,remote-pid = <5>;
fastrpc {
compatible = "qcom,fastrpc";
qcom,glink-channels = "fastrpcglink-apps-dsp";
label = "cdsp";
qcom,non-secure-domain;
#address-cells = <1>;
#size-cells = <0>;
compute-cb@1 {
compatible = "qcom,fastrpc-compute-cb";
reg = <1>;
iommus = <&apps_smmu 0x2161 0x0400>,
<&apps_smmu 0x1181 0x0420>;
};
compute-cb@2 {
compatible = "qcom,fastrpc-compute-cb";
reg = <2>;
iommus = <&apps_smmu 0x2162 0x0400>,
<&apps_smmu 0x1182 0x0420>;
};
compute-cb@3 {
compatible = "qcom,fastrpc-compute-cb";
reg = <3>;
iommus = <&apps_smmu 0x2163 0x0400>,
<&apps_smmu 0x1183 0x0420>;
};
compute-cb@4 {
compatible = "qcom,fastrpc-compute-cb";
reg = <4>;
iommus = <&apps_smmu 0x2164 0x0400>,
<&apps_smmu 0x1184 0x0420>;
};
compute-cb@5 {
compatible = "qcom,fastrpc-compute-cb";
reg = <5>;
iommus = <&apps_smmu 0x2165 0x0400>,
<&apps_smmu 0x1185 0x0420>;
};
compute-cb@6 {
compatible = "qcom,fastrpc-compute-cb";
reg = <6>;
iommus = <&apps_smmu 0x2166 0x0400>,
<&apps_smmu 0x1186 0x0420>;
};
compute-cb@7 {
compatible = "qcom,fastrpc-compute-cb";
reg = <7>;
iommus = <&apps_smmu 0x2167 0x0400>,
<&apps_smmu 0x1187 0x0420>;
};
compute-cb@8 {
compatible = "qcom,fastrpc-compute-cb";
reg = <8>;
iommus = <&apps_smmu 0x2168 0x0400>,
<&apps_smmu 0x1188 0x0420>;
};
/* note: secure cb9 in downstream */
};
};
};
};
thermal_zones: thermal-zones {
cpu0-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 1>;
trips {
cpu0_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu0_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu0_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu0_alert0>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu0_alert1>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu1-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 2>;
trips {
cpu1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu1_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu1_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu1_alert0>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu1_alert1>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu2-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 3>;
trips {
cpu2_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu2_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu2_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu2_alert0>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu2_alert1>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu3-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 4>;
trips {
cpu3_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu3_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu3_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu3_alert0>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu3_alert1>;
cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu4-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 7>;
trips {
cpu4_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_top_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu4_top_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu4_top_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu5-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 8>;
trips {
cpu5_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_top_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu5_top_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu5_top_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu6-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 9>;
trips {
cpu6_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_top_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu6_top_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu6_top_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu7-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 10>;
trips {
cpu7_top_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_top_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_top_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu7_top_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu7_top_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu4-bottom-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 11>;
trips {
cpu4_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu4_bottom_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu4_bottom_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu4_bottom_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu5-bottom-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 12>;
trips {
cpu5_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu5_bottom_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu5_bottom_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu5_bottom_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu6-bottom-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 13>;
trips {
cpu6_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu6_bottom_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu6_bottom_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu6_bottom_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
cpu7-bottom-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 14>;
trips {
cpu7_bottom_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_bottom_alert1: trip-point1 {
temperature = <95000>;
hysteresis = <2000>;
type = "passive";
};
cpu7_bottom_crit: cpu-crit {
temperature = <110000>;
hysteresis = <1000>;
type = "critical";
};
};
cooling-maps {
map0 {
trip = <&cpu7_bottom_alert0>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
map1 {
trip = <&cpu7_bottom_alert1>;
cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
<&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
};
};
};
aoss0-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 0>;
trips {
aoss0_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
cluster0-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 5>;
trips {
cluster0_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
cluster0_crit: cluster0_crit {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
cluster1-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens0 6>;
trips {
cluster1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
cluster1_crit: cluster1_crit {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
};
aoss1-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 0>;
trips {
aoss1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
gpu-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 1>;
trips {
gpu1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <1000>;
type = "hot";
};
};
};
gpu-bottom-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 2>;
trips {
gpu2_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <1000>;
type = "hot";
};
};
};
nspss1-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 3>;
trips {
nspss1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <1000>;
type = "hot";
};
};
};
nspss2-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 4>;
trips {
nspss2_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <1000>;
type = "hot";
};
};
};
nspss3-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 5>;
trips {
nspss3_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <1000>;
type = "hot";
};
};
};
video-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 6>;
trips {
video_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
mem-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 7>;
trips {
mem_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
modem1-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 8>;
trips {
modem1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
modem2-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 9>;
trips {
modem2_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
modem3-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 10>;
trips {
modem3_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
modem4-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 11>;
trips {
modem4_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
camera-top-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 12>;
trips {
camera1_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
cam-bottom-thermal {
polling-delay-passive = <250>;
polling-delay = <1000>;
thermal-sensors = <&tsens1 13>;
trips {
camera2_alert0: trip-point0 {
temperature = <90000>;
hysteresis = <2000>;
type = "hot";
};
};
};
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
};
};