700a2b53bd
Specify clock property in binding. Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/1605201148-4508-3-git-send-email-srinivas.neeli@xilinx.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
49 lines
1.7 KiB
Plaintext
49 lines
1.7 KiB
Plaintext
Xilinx plb/axi GPIO controller
|
|
|
|
Dual channel GPIO controller with configurable number of pins
|
|
(from 1 to 32 per channel). Every pin can be configured as
|
|
input/output/tristate. Both channels share the same global IRQ but
|
|
local interrupts can be enabled on channel basis.
|
|
|
|
Required properties:
|
|
- compatible : Should be "xlnx,xps-gpio-1.00.a"
|
|
- reg : Address and length of the register set for the device
|
|
- #gpio-cells : Should be two. The first cell is the pin number and the
|
|
second cell is used to specify optional parameters (currently unused).
|
|
- gpio-controller : Marks the device node as a GPIO controller.
|
|
|
|
Optional properties:
|
|
- clocks : Input clock specifier. Refer to common clock bindings.
|
|
- interrupts : Interrupt mapping for GPIO IRQ.
|
|
- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input
|
|
- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1
|
|
- xlnx,gpio-width : gpio width
|
|
- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode
|
|
- xlnx,is-dual : if 1, controller also uses the second channel
|
|
- xlnx,all-inputs-2 : as above but for the second channel
|
|
- xlnx,dout-default-2 : as above but the second channel
|
|
- xlnx,gpio2-width : as above but for the second channel
|
|
- xlnx,tri-default-2 : as above but for the second channel
|
|
|
|
|
|
Example:
|
|
gpio: gpio@40000000 {
|
|
#gpio-cells = <2>;
|
|
compatible = "xlnx,xps-gpio-1.00.a";
|
|
clocks = <&clkc25>;
|
|
gpio-controller ;
|
|
interrupt-parent = <µblaze_0_intc>;
|
|
interrupts = < 6 2 >;
|
|
reg = < 0x40000000 0x10000 >;
|
|
xlnx,all-inputs = <0x0>;
|
|
xlnx,all-inputs-2 = <0x0>;
|
|
xlnx,dout-default = <0x0>;
|
|
xlnx,dout-default-2 = <0x0>;
|
|
xlnx,gpio-width = <0x2>;
|
|
xlnx,gpio2-width = <0x2>;
|
|
xlnx,interrupt-present = <0x1>;
|
|
xlnx,is-dual = <0x1>;
|
|
xlnx,tri-default = <0xffffffff>;
|
|
xlnx,tri-default-2 = <0xffffffff>;
|
|
} ;
|