iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
2bb2a5d30a
linux/arch/arm/mach-omap2/board-apollon.c
Rajendra Nayak 4d7cb45ee8 ARM: omap: clk: add clk_prepare and clk_unprepare 
As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().

For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.

The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.

This is in preparation of OMAP moving to CCF.

Based on initial changes from Mike Turquette.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2012-09-22 10:50:01 -06:00

343 lines
8.5 KiB
C
Raw Blame History

/*
* linux/arch/arm/mach-omap2/board-apollon.c
*
* Copyright (C) 2005,2006 Samsung Electronics
* Author: Kyungmin Park <kyungmin.park@samsung.com>
*
* Modified from mach-omap/omap2/board-h4.c
*
* Code for apollon OMAP2 board. Should work on many OMAP2 systems where
* the bootloader passes the board-specific data to the kernel.
* Do not put any board specific code to this file; create a new machine
* type if you need custom low-level initializations.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/onenand.h>
#include <linux/delay.h>
#include <linux/leds.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/smc91x.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <plat/led.h>
#include "common.h"
#include <plat/gpmc.h>
#include <video/omapdss.h>
#include <video/omap-panel-generic-dpi.h>
#include "mux.h"
#include "control.h"
/* LED & Switch macros */
#define LED0_GPIO13 13
#define LED1_GPIO14 14
#define LED2_GPIO15 15
#define SW_ENTER_GPIO16 16
#define SW_UP_GPIO17 17
#define SW_DOWN_GPIO58 58
#define APOLLON_FLASH_CS 0
#define APOLLON_ETH_CS 1
#define APOLLON_ETHR_GPIO_IRQ 74
static struct mtd_partition apollon_partitions[] = {
{
.name = "X-Loader + U-Boot",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE,
},
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
},
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
},
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = SZ_16M,
},
{
.name = "filesystem00",
.offset = MTDPART_OFS_APPEND,
.size = SZ_32M,
},
{
.name = "filesystem01",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
},
};
static struct onenand_platform_data apollon_flash_data = {
.parts = apollon_partitions,
.nr_parts = ARRAY_SIZE(apollon_partitions),
};
static struct resource apollon_flash_resource[] = {
[0] = {
.flags = IORESOURCE_MEM,
},
};
static struct platform_device apollon_onenand_device = {
.name = "onenand-flash",
.id = -1,
.dev = {
.platform_data = &apollon_flash_data,
},
.num_resources = ARRAY_SIZE(apollon_flash_resource),
.resource = apollon_flash_resource,
};
static void __init apollon_flash_init(void)
{
unsigned long base;
if (gpmc_cs_request(APOLLON_FLASH_CS, SZ_128K, &base) < 0) {
printk(KERN_ERR "Cannot request OneNAND GPMC CS\n");
return;
}
apollon_flash_resource[0].start = base;
apollon_flash_resource[0].end = base + SZ_128K - 1;
}
static struct smc91x_platdata appolon_smc91x_info = {
.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
.leda = RPC_LED_100_10,
.ledb = RPC_LED_TX_RX,
};
static struct resource apollon_smc91x_resources[] = {
[0] = {
.flags = IORESOURCE_MEM,
},
[1] = {
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
};
static struct platform_device apollon_smc91x_device = {
.name = "smc91x",
.id = -1,
.dev = {
.platform_data = &appolon_smc91x_info,
},
.num_resources = ARRAY_SIZE(apollon_smc91x_resources),
.resource = apollon_smc91x_resources,
};
static struct omap_led_config apollon_led_config[] = {
{
.cdev = {
.name = "apollon:led0",
},
.gpio = LED0_GPIO13,
},
{
.cdev = {
.name = "apollon:led1",
},
.gpio = LED1_GPIO14,
},
{
.cdev = {
.name = "apollon:led2",
},
.gpio = LED2_GPIO15,
},
};
static struct omap_led_platform_data apollon_led_data = {
.nr_leds = ARRAY_SIZE(apollon_led_config),
.leds = apollon_led_config,
};
static struct platform_device apollon_led_device = {
.name = "omap-led",
.id = -1,
.dev = {
.platform_data = &apollon_led_data,
},
};
static struct platform_device *apollon_devices[] __initdata = {
&apollon_onenand_device,
&apollon_smc91x_device,
&apollon_led_device,
};
static inline void __init apollon_init_smc91x(void)
{
unsigned long base;
unsigned int rate;
struct clk *gpmc_fck;
int eth_cs;
int err;
gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
if (IS_ERR(gpmc_fck)) {
WARN_ON(1);
return;
}
clk_prepare_enable(gpmc_fck);
rate = clk_get_rate(gpmc_fck);
eth_cs = APOLLON_ETH_CS;
/* Make sure CS1 timings are correct */
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
if (rate >= 160000000) {
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
} else if (rate >= 130000000) {
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
} else {/* rate = 100000000 */
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
}
if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
goto out;
}
apollon_smc91x_resources[0].start = base + 0x300;
apollon_smc91x_resources[0].end = base + 0x30f;
udelay(100);
omap_mux_init_gpio(APOLLON_ETHR_GPIO_IRQ, 0);
err = gpio_request_one(APOLLON_ETHR_GPIO_IRQ, GPIOF_IN, "SMC91x irq");
if (err) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
APOLLON_ETHR_GPIO_IRQ);
gpmc_cs_free(APOLLON_ETH_CS);
}
out:
clk_disable_unprepare(gpmc_fck);
clk_put(gpmc_fck);
}
static struct panel_generic_dpi_data apollon_panel_data = {
.name = "apollon",
};
static struct omap_dss_device apollon_lcd_device = {
.name = "lcd",
.driver_name = "generic_dpi_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
.phy.dpi.data_lines = 18,
.data = &apollon_panel_data,
};
static struct omap_dss_device *apollon_dss_devices[] = {
&apollon_lcd_device,
};
static struct omap_dss_board_info apollon_dss_data = {
.num_devices = ARRAY_SIZE(apollon_dss_devices),
.devices = apollon_dss_devices,
.default_device = &apollon_lcd_device,
};
static struct gpio apollon_gpio_leds[] __initdata = {
{ LED0_GPIO13, GPIOF_OUT_INIT_LOW, "LED0" }, /* LED0 - AA10 */
{ LED1_GPIO14, GPIOF_OUT_INIT_LOW, "LED1" }, /* LED1 - AA6 */
{ LED2_GPIO15, GPIOF_OUT_INIT_LOW, "LED2" }, /* LED2 - AA4 */
};
static void __init apollon_led_init(void)
{
omap_mux_init_signal("vlynq_clk.gpio_13", 0);
omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
}
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static void __init omap_apollon_init(void)
{
u32 v;
omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
apollon_init_smc91x();
apollon_led_init();
apollon_flash_init();
/* REVISIT: where's the correct place */
omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
/* LCD PWR_EN */
omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
/* Use Internal loop-back in MMC/SDIO Module Input Clock selection */
v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
v |= (1 << 24);
omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
/*
* Make sure the serial ports are muxed on at this point.
* You have to mux them off in device drivers later on
* if not needed.
*/
apollon_smc91x_resources[1].start = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
apollon_smc91x_resources[1].end = gpio_to_irq(APOLLON_ETHR_GPIO_IRQ);
platform_add_devices(apollon_devices, ARRAY_SIZE(apollon_devices));
omap_serial_init();
omap_sdrc_init(NULL, NULL);
omap_display_init(&apollon_dss_data);
}
MACHINE_START(OMAP_APOLLON, "OMAP24xx Apollon")
/* Maintainer: Kyungmin Park <kyungmin.park@samsung.com> */
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap242x_map_io,
.init_early = omap2420_init_early,
.init_irq = omap2_init_irq,
.handle_irq = omap2_intc_handle_irq,
.init_machine = omap_apollon_init,
.init_late = omap2420_init_late,
.timer = &omap2_timer,
.restart = omap_prcm_restart,
MACHINE_END
Reference in New Issue View Git Blame Copy Permalink