iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
linux/drivers/usb/dwc3/dwc3-pci.c
Gratian Crisan b32b8f2b95 usb: dwc3: pci: skip BYT GPIO lookup table for hardwired phy 
Hardware based on the Bay Trail / BYT SoCs require an external ULPI phy for
USB device-mode. The phy chip usually has its 'reset' and 'chip select'
lines connected to GPIOs described by ACPI fwnodes in the DSDT table.

Because of hardware with missing ACPI resources for the 'reset' and 'chip
select' GPIOs commit 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table
on platforms without ACPI GPIO resources") introduced a fallback
gpiod_lookup_table with hard-coded mappings for Bay Trail devices.

However there are existing Bay Trail based devices, like the National
Instruments cRIO-903x series, where the phy chip has its 'reset' and
'chip-select' lines always asserted in hardware via resistor pull-ups. On
this hardware the phy chip is always enabled and the ACPI dsdt table is
missing information not only for the 'chip-select' and 'reset' lines but
also for the BYT GPIO controller itself "INT33FC".

With the introduction of the gpiod_lookup_table initializing the USB
device-mode on these hardware now errors out. The error comes from the
gpiod_get_optional() calls in dwc3_pci_quirks() which will now return an
-ENOENT error due to the missing ACPI entry for the INT33FC gpio controller
used in the aforementioned table.

This hardware used to work before because gpiod_get_optional() will return
NULL instead of -ENOENT if no GPIO has been assigned to the requested
function. The dwc3_pci_quirks() code for setting the 'cs' and 'reset' GPIOs
was then skipped (due to the NULL return). This is the correct behavior in
cases where the phy chip is hardwired and there are no GPIOs to control.

Since the gpiod_lookup_table relies on the presence of INT33FC fwnode
in ACPI tables only add the table if we know the entry for the INT33FC
gpio controller is present. This allows Bay Trail based devices with
hardwired dwc3 ULPI phys to continue working.

Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@kernel.org>
Signed-off-by: Gratian Crisan <gratian.crisan@ni.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230726184555.218091-2-gratian.crisan@ni.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-07-27 10:37:01 +02:00

522 lines
15 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0
/*
* dwc3-pci.c - PCI Specific glue layer
*
* Copyright (C) 2010-2011 Texas Instruments Incorporated - https://www.ti.com
*
* Authors: Felipe Balbi <balbi@ti.com>,
* Sebastian Andrzej Siewior <bigeasy@linutronix.de>
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/workqueue.h>
#include <linux/pm_runtime.h>
#include <linux/platform_device.h>
#include <linux/gpio/consumer.h>
#include <linux/gpio/machine.h>
#include <linux/acpi.h>
#include <linux/delay.h>
#define PCI_DEVICE_ID_INTEL_BYT 0x0f37
#define PCI_DEVICE_ID_INTEL_MRFLD 0x119e
#define PCI_DEVICE_ID_INTEL_BSW 0x22b7
#define PCI_DEVICE_ID_INTEL_SPTLP 0x9d30
#define PCI_DEVICE_ID_INTEL_SPTH 0xa130
#define PCI_DEVICE_ID_INTEL_BXT 0x0aaa
#define PCI_DEVICE_ID_INTEL_BXT_M 0x1aaa
#define PCI_DEVICE_ID_INTEL_APL 0x5aaa
#define PCI_DEVICE_ID_INTEL_KBP 0xa2b0
#define PCI_DEVICE_ID_INTEL_CMLLP 0x02ee
#define PCI_DEVICE_ID_INTEL_CMLH 0x06ee
#define PCI_DEVICE_ID_INTEL_GLK 0x31aa
#define PCI_DEVICE_ID_INTEL_CNPLP 0x9dee
#define PCI_DEVICE_ID_INTEL_CNPH 0xa36e
#define PCI_DEVICE_ID_INTEL_CNPV 0xa3b0
#define PCI_DEVICE_ID_INTEL_ICLLP 0x34ee
#define PCI_DEVICE_ID_INTEL_EHL 0x4b7e
#define PCI_DEVICE_ID_INTEL_TGPLP 0xa0ee
#define PCI_DEVICE_ID_INTEL_TGPH 0x43ee
#define PCI_DEVICE_ID_INTEL_JSP 0x4dee
#define PCI_DEVICE_ID_INTEL_ADL 0x460e
#define PCI_DEVICE_ID_INTEL_ADL_PCH 0x51ee
#define PCI_DEVICE_ID_INTEL_ADLN 0x465e
#define PCI_DEVICE_ID_INTEL_ADLN_PCH 0x54ee
#define PCI_DEVICE_ID_INTEL_ADLS 0x7ae1
#define PCI_DEVICE_ID_INTEL_RPL 0xa70e
#define PCI_DEVICE_ID_INTEL_RPLS 0x7a61
#define PCI_DEVICE_ID_INTEL_MTLM 0x7eb1
#define PCI_DEVICE_ID_INTEL_MTLP 0x7ec1
#define PCI_DEVICE_ID_INTEL_MTLS 0x7f6f
#define PCI_DEVICE_ID_INTEL_MTL 0x7e7e
#define PCI_DEVICE_ID_INTEL_TGL 0x9a15
#define PCI_DEVICE_ID_AMD_MR 0x163a
#define PCI_INTEL_BXT_DSM_GUID "732b85d5-b7a7-4a1b-9ba0-4bbd00ffd511"
#define PCI_INTEL_BXT_FUNC_PMU_PWR 4
#define PCI_INTEL_BXT_STATE_D0 0
#define PCI_INTEL_BXT_STATE_D3 3
#define GP_RWBAR 1
#define GP_RWREG1 0xa0
#define GP_RWREG1_ULPI_REFCLK_DISABLE (1 << 17)
/**
* struct dwc3_pci - Driver private structure
* @dwc3: child dwc3 platform_device
* @pci: our link to PCI bus
* @guid: _DSM GUID
* @has_dsm_for_pm: true for devices which need to run _DSM on runtime PM
* @wakeup_work: work for asynchronous resume
*/
struct dwc3_pci {
struct platform_device *dwc3;
struct pci_dev *pci;
guid_t guid;
unsigned int has_dsm_for_pm:1;
struct work_struct wakeup_work;
};
static const struct acpi_gpio_params reset_gpios = { 0, 0, false };
static const struct acpi_gpio_params cs_gpios = { 1, 0, false };
static const struct acpi_gpio_mapping acpi_dwc3_byt_gpios[] = {
{ "reset-gpios", &reset_gpios, 1 },
{ "cs-gpios", &cs_gpios, 1 },
{ },
};
static struct gpiod_lookup_table platform_bytcr_gpios = {
.dev_id = "0000:00:16.0",
.table = {
GPIO_LOOKUP("INT33FC:00", 54, "cs", GPIO_ACTIVE_HIGH),
GPIO_LOOKUP("INT33FC:02", 14, "reset", GPIO_ACTIVE_HIGH),
{}
},
};
static int dwc3_byt_enable_ulpi_refclock(struct pci_dev *pci)
{
void __iomem *reg;
u32 value;
reg = pcim_iomap(pci, GP_RWBAR, 0);
if (!reg)
return -ENOMEM;
value = readl(reg + GP_RWREG1);
if (!(value & GP_RWREG1_ULPI_REFCLK_DISABLE))
goto unmap; /* ULPI refclk already enabled */
value &= ~GP_RWREG1_ULPI_REFCLK_DISABLE;
writel(value, reg + GP_RWREG1);
/* This comes from the Intel Android x86 tree w/o any explanation */
msleep(100);
unmap:
pcim_iounmap(pci, reg);
return 0;
}
static const struct property_entry dwc3_pci_intel_properties[] = {
PROPERTY_ENTRY_STRING("dr_mode", "peripheral"),
PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
{}
};
static const struct property_entry dwc3_pci_intel_phy_charger_detect_properties[] = {
PROPERTY_ENTRY_STRING("dr_mode", "peripheral"),
PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"),
PROPERTY_ENTRY_BOOL("linux,phy_charger_detect"),
PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
{}
};
static const struct property_entry dwc3_pci_intel_byt_properties[] = {
PROPERTY_ENTRY_STRING("dr_mode", "peripheral"),
PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"),
PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
{}
};
static const struct property_entry dwc3_pci_mrfld_properties[] = {
PROPERTY_ENTRY_STRING("dr_mode", "otg"),
PROPERTY_ENTRY_STRING("linux,extcon-name", "mrfld_bcove_pwrsrc"),
PROPERTY_ENTRY_BOOL("snps,dis_u3_susphy_quirk"),
PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"),
PROPERTY_ENTRY_BOOL("snps,usb2-gadget-lpm-disable"),
PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
{}
};
static const struct property_entry dwc3_pci_amd_properties[] = {
PROPERTY_ENTRY_BOOL("snps,has-lpm-erratum"),
PROPERTY_ENTRY_U8("snps,lpm-nyet-threshold", 0xf),
PROPERTY_ENTRY_BOOL("snps,u2exit_lfps_quirk"),
PROPERTY_ENTRY_BOOL("snps,u2ss_inp3_quirk"),
PROPERTY_ENTRY_BOOL("snps,req_p1p2p3_quirk"),
PROPERTY_ENTRY_BOOL("snps,del_p1p2p3_quirk"),
PROPERTY_ENTRY_BOOL("snps,del_phy_power_chg_quirk"),
PROPERTY_ENTRY_BOOL("snps,lfps_filter_quirk"),
PROPERTY_ENTRY_BOOL("snps,rx_detect_poll_quirk"),
PROPERTY_ENTRY_BOOL("snps,tx_de_emphasis_quirk"),
PROPERTY_ENTRY_U8("snps,tx_de_emphasis", 1),
/* FIXME these quirks should be removed when AMD NL tapes out */
PROPERTY_ENTRY_BOOL("snps,disable_scramble_quirk"),
PROPERTY_ENTRY_BOOL("snps,dis_u3_susphy_quirk"),
PROPERTY_ENTRY_BOOL("snps,dis_u2_susphy_quirk"),
PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
{}
};
static const struct property_entry dwc3_pci_mr_properties[] = {
PROPERTY_ENTRY_STRING("dr_mode", "otg"),
PROPERTY_ENTRY_BOOL("usb-role-switch"),
PROPERTY_ENTRY_STRING("role-switch-default-mode", "host"),
PROPERTY_ENTRY_BOOL("linux,sysdev_is_parent"),
{}
};
static const struct software_node dwc3_pci_intel_swnode = {
.properties = dwc3_pci_intel_properties,
};
static const struct software_node dwc3_pci_intel_phy_charger_detect_swnode = {
.properties = dwc3_pci_intel_phy_charger_detect_properties,
};
static const struct software_node dwc3_pci_intel_byt_swnode = {
.properties = dwc3_pci_intel_byt_properties,
};
static const struct software_node dwc3_pci_intel_mrfld_swnode = {
.properties = dwc3_pci_mrfld_properties,
};
static const struct software_node dwc3_pci_amd_swnode = {
.properties = dwc3_pci_amd_properties,
};
static const struct software_node dwc3_pci_amd_mr_swnode = {
.properties = dwc3_pci_mr_properties,
};
static int dwc3_pci_quirks(struct dwc3_pci *dwc,
const struct software_node *swnode)
{
struct pci_dev *pdev = dwc->pci;
if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
if (pdev->device == PCI_DEVICE_ID_INTEL_BXT ||
pdev->device == PCI_DEVICE_ID_INTEL_BXT_M ||
pdev->device == PCI_DEVICE_ID_INTEL_EHL) {
guid_parse(PCI_INTEL_BXT_DSM_GUID, &dwc->guid);
dwc->has_dsm_for_pm = true;
}
if (pdev->device == PCI_DEVICE_ID_INTEL_BYT) {
struct gpio_desc *gpio;
int ret;
/* On BYT the FW does not always enable the refclock */
ret = dwc3_byt_enable_ulpi_refclock(pdev);
if (ret)
return ret;
ret = devm_acpi_dev_add_driver_gpios(&pdev->dev,
acpi_dwc3_byt_gpios);
if (ret)
dev_dbg(&pdev->dev, "failed to add mapping table\n");
/*
* A lot of BYT devices lack ACPI resource entries for
* the GPIOs. If the ACPI entry for the GPIO controller
* is present add a fallback mapping to the reference
* design GPIOs which all boards seem to use.
*/
if (acpi_dev_present("INT33FC", NULL, -1))
gpiod_add_lookup_table(&platform_bytcr_gpios);
/*
* These GPIOs will turn on the USB2 PHY. Note that we have to
* put the gpio descriptors again here because the phy driver
* might want to grab them, too.
*/
gpio = gpiod_get_optional(&pdev->dev, "cs", GPIOD_OUT_LOW);
if (IS_ERR(gpio))
return PTR_ERR(gpio);
gpiod_set_value_cansleep(gpio, 1);
gpiod_put(gpio);
gpio = gpiod_get_optional(&pdev->dev, "reset", GPIOD_OUT_LOW);
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
gpiod_set_value_cansleep(gpio, 1);
gpiod_put(gpio);
usleep_range(10000, 11000);
}
/*
* Make the pdev name predictable (only 1 DWC3 on BYT)
* and patch the phy dev-name into the lookup table so
* that the phy-driver can get the GPIOs.
*/
dwc->dwc3->id = PLATFORM_DEVID_NONE;
platform_bytcr_gpios.dev_id = "dwc3.ulpi";
/*
* Some Android tablets with a Crystal Cove PMIC
* (INT33FD), rely on the TUSB1211 phy for charger
* detection. These can be identified by them _not_
* using the standard ACPI battery and ac drivers.
*/
if (acpi_dev_present("INT33FD", "1", 2) &&
acpi_quirk_skip_acpi_ac_and_battery()) {
dev_info(&pdev->dev, "Using TUSB1211 phy for charger detection\n");
swnode = &dwc3_pci_intel_phy_charger_detect_swnode;
}
}
}
return device_add_software_node(&dwc->dwc3->dev, swnode);
}
#ifdef CONFIG_PM
static void dwc3_pci_resume_work(struct work_struct *work)
{
struct dwc3_pci *dwc = container_of(work, struct dwc3_pci, wakeup_work);
struct platform_device *dwc3 = dwc->dwc3;
int ret;
ret = pm_runtime_get_sync(&dwc3->dev);
if (ret < 0) {
pm_runtime_put_sync_autosuspend(&dwc3->dev);
return;
}
pm_runtime_mark_last_busy(&dwc3->dev);
pm_runtime_put_sync_autosuspend(&dwc3->dev);
}
#endif
static int dwc3_pci_probe(struct pci_dev *pci, const struct pci_device_id *id)
{
struct dwc3_pci *dwc;
struct resource res[2];
int ret;
struct device *dev = &pci->dev;
ret = pcim_enable_device(pci);
if (ret) {
dev_err(dev, "failed to enable pci device\n");
return -ENODEV;
}
pci_set_master(pci);
dwc = devm_kzalloc(dev, sizeof(*dwc), GFP_KERNEL);
if (!dwc)
return -ENOMEM;
dwc->dwc3 = platform_device_alloc("dwc3", PLATFORM_DEVID_AUTO);
if (!dwc->dwc3)
return -ENOMEM;
memset(res, 0x00, sizeof(struct resource) * ARRAY_SIZE(res));
res[0].start = pci_resource_start(pci, 0);
res[0].end = pci_resource_end(pci, 0);
res[0].name = "dwc_usb3";
res[0].flags = IORESOURCE_MEM;
res[1].start = pci->irq;
res[1].name = "dwc_usb3";
res[1].flags = IORESOURCE_IRQ;
ret = platform_device_add_resources(dwc->dwc3, res, ARRAY_SIZE(res));
if (ret) {
dev_err(dev, "couldn't add resources to dwc3 device\n");
goto err;
}
dwc->pci = pci;
dwc->dwc3->dev.parent = dev;
ACPI_COMPANION_SET(&dwc->dwc3->dev, ACPI_COMPANION(dev));
ret = dwc3_pci_quirks(dwc, (void *)id->driver_data);
if (ret)
goto err;
ret = platform_device_add(dwc->dwc3);
if (ret) {
dev_err(dev, "failed to register dwc3 device\n");
goto err;
}
device_init_wakeup(dev, true);
pci_set_drvdata(pci, dwc);
pm_runtime_put(dev);
#ifdef CONFIG_PM
INIT_WORK(&dwc->wakeup_work, dwc3_pci_resume_work);
#endif
return 0;
err:
device_remove_software_node(&dwc->dwc3->dev);
platform_device_put(dwc->dwc3);
return ret;
}
static void dwc3_pci_remove(struct pci_dev *pci)
{
struct dwc3_pci *dwc = pci_get_drvdata(pci);
struct pci_dev *pdev = dwc->pci;
if (pdev->device == PCI_DEVICE_ID_INTEL_BYT)
gpiod_remove_lookup_table(&platform_bytcr_gpios);
#ifdef CONFIG_PM
cancel_work_sync(&dwc->wakeup_work);
#endif
device_init_wakeup(&pci->dev, false);
pm_runtime_get(&pci->dev);
device_remove_software_node(&dwc->dwc3->dev);
platform_device_unregister(dwc->dwc3);
}
static const struct pci_device_id dwc3_pci_id_table[] = {
{ PCI_DEVICE_DATA(INTEL, BSW, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, BYT, &dwc3_pci_intel_byt_swnode) },
{ PCI_DEVICE_DATA(INTEL, MRFLD, &dwc3_pci_intel_mrfld_swnode) },
{ PCI_DEVICE_DATA(INTEL, CMLLP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, CMLH, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, SPTLP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, SPTH, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, BXT, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, BXT_M, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, APL, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, KBP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, GLK, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, CNPLP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, CNPH, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, CNPV, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, ICLLP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, EHL, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, TGPLP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, TGPH, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, JSP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, ADL, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, ADL_PCH, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, ADLN, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, ADLN_PCH, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, ADLS, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, RPL, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, RPLS, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, MTLM, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, MTLP, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, MTL, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, MTLS, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(INTEL, TGL, &dwc3_pci_intel_swnode) },
{ PCI_DEVICE_DATA(AMD, NL_USB, &dwc3_pci_amd_swnode) },
{ PCI_DEVICE_DATA(AMD, MR, &dwc3_pci_amd_mr_swnode) },
{ } /* Terminating Entry */
};
MODULE_DEVICE_TABLE(pci, dwc3_pci_id_table);
#if defined(CONFIG_PM) || defined(CONFIG_PM_SLEEP)
static int dwc3_pci_dsm(struct dwc3_pci *dwc, int param)
{
union acpi_object *obj;
union acpi_object tmp;
union acpi_object argv4 = ACPI_INIT_DSM_ARGV4(1, &tmp);
if (!dwc->has_dsm_for_pm)
return 0;
tmp.type = ACPI_TYPE_INTEGER;
tmp.integer.value = param;
obj = acpi_evaluate_dsm(ACPI_HANDLE(&dwc->pci->dev), &dwc->guid,
1, PCI_INTEL_BXT_FUNC_PMU_PWR, &argv4);
if (!obj) {
dev_err(&dwc->pci->dev, "failed to evaluate _DSM\n");
return -EIO;
}
ACPI_FREE(obj);
return 0;
}
#endif /* CONFIG_PM || CONFIG_PM_SLEEP */
#ifdef CONFIG_PM
static int dwc3_pci_runtime_suspend(struct device *dev)
{
struct dwc3_pci *dwc = dev_get_drvdata(dev);
if (device_can_wakeup(dev))
return dwc3_pci_dsm(dwc, PCI_INTEL_BXT_STATE_D3);
return -EBUSY;
}
static int dwc3_pci_runtime_resume(struct device *dev)
{
struct dwc3_pci *dwc = dev_get_drvdata(dev);
int ret;
ret = dwc3_pci_dsm(dwc, PCI_INTEL_BXT_STATE_D0);
if (ret)
return ret;
queue_work(pm_wq, &dwc->wakeup_work);
return 0;
}
#endif /* CONFIG_PM */
#ifdef CONFIG_PM_SLEEP
static int dwc3_pci_suspend(struct device *dev)
{
struct dwc3_pci *dwc = dev_get_drvdata(dev);
return dwc3_pci_dsm(dwc, PCI_INTEL_BXT_STATE_D3);
}
static int dwc3_pci_resume(struct device *dev)
{
struct dwc3_pci *dwc = dev_get_drvdata(dev);
return dwc3_pci_dsm(dwc, PCI_INTEL_BXT_STATE_D0);
}
#endif /* CONFIG_PM_SLEEP */
static const struct dev_pm_ops dwc3_pci_dev_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(dwc3_pci_suspend, dwc3_pci_resume)
SET_RUNTIME_PM_OPS(dwc3_pci_runtime_suspend, dwc3_pci_runtime_resume,
NULL)
};
static struct pci_driver dwc3_pci_driver = {
.name = "dwc3-pci",
.id_table = dwc3_pci_id_table,
.probe = dwc3_pci_probe,
.remove = dwc3_pci_remove,
.driver = {
.pm = &dwc3_pci_dev_pm_ops,
}
};
MODULE_AUTHOR("Felipe Balbi <balbi@ti.com>");
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("DesignWare USB3 PCI Glue Layer");
module_pci_driver(dwc3_pci_driver);
Reference in New Issue View Git Blame Copy Permalink