d4918ebb5c
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 37a4bdead109 ("ARM: dts: imx6sx-sdb: Assign corresponding power supply for LDOs")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
156 lines
3.0 KiB
Plaintext
156 lines
3.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
//
|
|
// Copyright (C) 2015 Freescale Semiconductor, Inc.
|
|
|
|
#include "imx6sx-sdb.dtsi"
|
|
|
|
/ {
|
|
model = "Freescale i.MX6 SoloX SDB RevB Board";
|
|
};
|
|
|
|
&i2c1 {
|
|
clock-frequency = <100000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_i2c1>;
|
|
status = "okay";
|
|
|
|
pmic: pfuze100@8 {
|
|
compatible = "fsl,pfuze200";
|
|
reg = <0x08>;
|
|
|
|
regulators {
|
|
sw1a_reg: sw1ab {
|
|
regulator-min-microvolt = <300000>;
|
|
regulator-max-microvolt = <1875000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
regulator-ramp-delay = <6250>;
|
|
};
|
|
|
|
sw2_reg: sw2 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
sw3a_reg: sw3a {
|
|
regulator-min-microvolt = <400000>;
|
|
regulator-max-microvolt = <1975000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
sw3b_reg: sw3b {
|
|
regulator-min-microvolt = <400000>;
|
|
regulator-max-microvolt = <1975000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
swbst_reg: swbst {
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <5150000>;
|
|
};
|
|
|
|
snvs_reg: vsnvs {
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vref_reg: vrefddr {
|
|
regulator-boot-on;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen1_reg: vgen1 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1550000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen2_reg: vgen2 {
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1550000>;
|
|
};
|
|
|
|
vgen3_reg: vgen3 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen4_reg: vgen4 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen5_reg: vgen5 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
vgen6_reg: vgen6 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&qspi2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_qspi2>;
|
|
status = "okay";
|
|
|
|
flash0: n25q256a@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "micron,n25q256a", "jedec,spi-nor";
|
|
spi-max-frequency = <29000000>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-tx-bus-width = <4>;
|
|
reg = <0>;
|
|
};
|
|
|
|
flash1: n25q256a@2 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "micron,n25q256a", "jedec,spi-nor";
|
|
spi-max-frequency = <29000000>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-tx-bus-width = <4>;
|
|
reg = <2>;
|
|
};
|
|
};
|
|
|
|
®_arm {
|
|
vin-supply = <&sw1a_reg>;
|
|
};
|
|
|
|
®_soc {
|
|
vin-supply = <&sw1a_reg>;
|
|
};
|
|
|
|
®_vdd1p1 {
|
|
vin-supply = <&vgen6_reg>;
|
|
};
|
|
|
|
®_vdd2p5 {
|
|
vin-supply = <&vgen6_reg>;
|
|
};
|
|
|
|
®_can_stby {
|
|
/* Transceiver EN/STBY is active low on RevB board */
|
|
gpio = <&gpio4 27 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&snvs_pwrkey {
|
|
status = "okay";
|
|
};
|