233cbffaa0
I've managed to get about everything wrong while digging these out of OEM's board file. Correct the bus numbers, the exact model of the NOR flash, polarity of the chip selects and align the SPI frequency with the data sheet. Tested that it works now, with a slight fix to the PXA SSP driver. Link: https://lore.kernel.org/r/20200419171157.672999-16-lkundrak@v3.sk Signed-off-by: Lubomir Rintel <lkundrak@v3.sk> Cc: <stable@vger.kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
117 lines
1.7 KiB
Plaintext
117 lines
1.7 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/*
|
|
* Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
|
|
*
|
|
* Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "mmp3.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
/ {
|
|
model = "Dell Ariel";
|
|
compatible = "dell,wyse-ariel", "marvell,mmp3";
|
|
|
|
aliases {
|
|
serial2 = &uart3;
|
|
};
|
|
|
|
chosen {
|
|
#address-cells = <0x1>;
|
|
#size-cells = <0x1>;
|
|
ranges;
|
|
bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
|
|
};
|
|
|
|
memory@0 {
|
|
linux,usable-memory = <0x0 0x7f600000>;
|
|
available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
|
|
reg = <0x0 0x80000000>;
|
|
device_type = "memory";
|
|
};
|
|
};
|
|
|
|
&uart3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_otg0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_otg_phy0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&hsic0 {
|
|
status = "okay";
|
|
|
|
usb1@1 {
|
|
compatible = "usb424,2640";
|
|
reg = <0x01>;
|
|
#address-cells = <0x01>;
|
|
#size-cells = <0x00>;
|
|
|
|
mass-storage@1 {
|
|
compatible = "usb424,4040";
|
|
reg = <0x01>;
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|
|
|
|
&hsic_phy0 {
|
|
status = "okay";
|
|
reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&mmc3 {
|
|
status = "okay";
|
|
max-frequency = <50000000>;
|
|
status = "okay";
|
|
bus-width = <8>;
|
|
non-removable;
|
|
cap-mmc-highspeed;
|
|
};
|
|
|
|
&twsi1 {
|
|
status = "okay";
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1338";
|
|
reg = <0x68>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&twsi3 {
|
|
status = "okay";
|
|
};
|
|
|
|
&twsi4 {
|
|
status = "okay";
|
|
};
|
|
|
|
&ssp1 {
|
|
status = "okay";
|
|
cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
|
|
|
|
firmware-flash@0 {
|
|
compatible = "winbond,w25q32", "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <104000000>;
|
|
m25p,fast-read;
|
|
};
|
|
};
|
|
|
|
&ssp2 {
|
|
cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|