iv/linux
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity
linux/net/dsa/dsa_priv.h
Vladimir Oltean 06cfb2df7e net: dsa: don't advertise 'rx-vlan-filter' when not needed 
There have been multiple independent reports about
dsa_slave_vlan_rx_add_vid being called (and consequently calling the
drivers' .port_vlan_add) when it isn't needed, and sometimes (not
always) causing problems in the process.

Case 1:
mv88e6xxx_port_vlan_prepare is stubborn and only accepts VLANs on
bridged ports. That is understandably so, because standalone mv88e6xxx
ports are VLAN-unaware, and VTU entries are said to be a scarce
resource.

Otherwise said, the following fails lamentably on mv88e6xxx:

ip link add br0 type bridge vlan_filtering 1
ip link set lan3 master br0
ip link add link lan10 name lan10.1 type vlan id 1
[485256.724147] mv88e6085 d0032004.mdio-mii:12: p10: hw VLAN 1 already used by port 3 in br0
RTNETLINK answers: Operation not supported

This has become a worse issue since commit 9b236d2a69da ("net: dsa:
Advertise the VLAN offload netdev ability only if switch supports it").
Up to that point, the driver was returning -EOPNOTSUPP and DSA was
reconverting that error to 0, making the 8021q upper think all is ok
(but obviously the error message was there even prior to this change).
After that change the -EOPNOTSUPP is propagated to vlan_vid_add, and it
is a hard error.

Case 2:
Ports that don't offload the Linux bridge (have a dp->bridge_dev = NULL
because they don't implement .port_bridge_{join,leave}). Understandably,
a standalone port should not offload VLANs either, it should remain VLAN
unaware and any VLAN should be a software VLAN (as long as the hardware
is not quirky, that is).

In fact, dsa_slave_port_obj_add does do the right thing and rejects
switchdev VLAN objects coming from the bridge when that bridge is not
offloaded:

	case SWITCHDEV_OBJ_ID_PORT_VLAN:
		if (!dsa_port_offloads_bridge_port(dp, obj->orig_dev))
			return -EOPNOTSUPP;

		err = dsa_slave_vlan_add(dev, obj, extack);

But it seems that the bridge is able to trick us. The __vlan_vid_add
from br_vlan.c has:

	/* Try switchdev op first. In case it is not supported, fallback to
	 * 8021q add.
	 */
	err = br_switchdev_port_vlan_add(dev, v->vid, flags, extack);
	if (err == -EOPNOTSUPP)
		return vlan_vid_add(dev, br->vlan_proto, v->vid);

So it says "no, no, you need this VLAN in your life!". And we, naive as
we are, say "oh, this comes from the vlan_vid_add code path, it must be
an 8021q upper, sure, I'll take that". And we end up with that bridge
VLAN installed on our port anyway. But this time, it has the wrong flags:
if the bridge was trying to install VLAN 1 as a pvid/untagged VLAN,
failed via switchdev, retried via vlan_vid_add, we have this comment:

	/* This API only allows programming tagged, non-PVID VIDs */

So what we do makes absolutely no sense.

Backtracing a bit, we see the common pattern. We allow the network stack
to think that our standalone ports are VLAN-aware, but they aren't, for
the vast majority of switches. The quirky ones should not dictate the
norm. The dsa_slave_vlan_rx_add_vid and dsa_slave_vlan_rx_kill_vid
methods exist for drivers that need the 'rx-vlan-filter: on' feature in
ethtool -k, which can be due to any of the following reasons:

1. vlan_filtering_is_global = true, and some ports are under a
   VLAN-aware bridge while others are standalone, and the standalone
   ports would otherwise drop VLAN-tagged traffic. This is described in
   commit 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid
   implementation").

2. the ports that are under a VLAN-aware bridge should also set this
   feature, for 8021q uppers having a VID not claimed by the bridge.
   In this case, the driver will essentially not even know that the VID
   is coming from the 8021q layer and not the bridge.

3. Hellcreek. This driver needs it because in standalone mode, it uses
   unique VLANs per port to ensure separation. For separation of untagged
   traffic, it uses different PVIDs for each port, and for separation of
   VLAN-tagged traffic, it never accepts 8021q uppers with the same vid
   on two ports.

If a driver does not fall under any of the above 3 categories, there is
no reason why it should advertise the 'rx-vlan-filter' feature, therefore
no reason why it should offload the VLANs added through vlan_vid_add.

This commit fixes the problem by removing the 'rx-vlan-filter' feature
from the slave devices when they operate in standalone mode, and when
they offload a VLAN-unaware bridge.

The way it works is that vlan_vid_add will now stop its processing here:

vlan_add_rx_filter_info:
	if (!vlan_hw_filter_capable(dev, proto))
		return 0;

So the VLAN will still be saved in the interface's VLAN RX filtering
list, but because it does not declare VLAN filtering in its features,
the 8021q module will return zero without committing that VLAN to
hardware.

This gives the drivers what they want, since it keeps the 8021q VLANs
away from the VLAN table until VLAN awareness is enabled (point at which
the ports are no longer standalone, hence in the mv88e6xxx case, the
check in mv88e6xxx_port_vlan_prepare passes).

Since the issue predates the existence of the hellcreek driver, case 3
will be dealt with in a separate patch.

The main change that this patch makes is to no longer set
NETIF_F_HW_VLAN_CTAG_FILTER unconditionally, but toggle it dynamically
(for most switches, never).

The second part of the patch addresses an issue that the first part
introduces: because the 'rx-vlan-filter' feature is now dynamically
toggled, and our .ndo_vlan_rx_add_vid does not get called when
'rx-vlan-filter' is off, we need to avoid bugs such as the following by
replaying the VLANs from 8021q uppers every time we enable VLAN
filtering:

ip link add link lan0 name lan0.100 type vlan id 100
ip addr add 192.168.100.1/24 dev lan0.100
ping 192.168.100.2 # should work
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0
ping 192.168.100.2 # should still work
ip link set br0 type bridge vlan_filtering 1
ping 192.168.100.2 # should still work but doesn't

As reported by Florian, some drivers look at ds->vlan_filtering in
their .port_vlan_add() implementation. So this patch also makes sure
that ds->vlan_filtering is committed before calling the driver. This is
the reason why it is first committed, then restored on the failure path.

Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-24 09:30:58 +01:00

564 lines
18 KiB
C
Raw Blame History

/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* net/dsa/dsa_priv.h - Hardware switch handling
* Copyright (c) 2008-2009 Marvell Semiconductor
*/
#ifndef __DSA_PRIV_H
#define __DSA_PRIV_H
#include <linux/if_bridge.h>
#include <linux/phy.h>
#include <linux/netdevice.h>
#include <linux/netpoll.h>
#include <net/dsa.h>
#include <net/gro_cells.h>
#define DSA_MAX_NUM_OFFLOADING_BRIDGES BITS_PER_LONG
enum {
DSA_NOTIFIER_AGEING_TIME,
DSA_NOTIFIER_BRIDGE_JOIN,
DSA_NOTIFIER_BRIDGE_LEAVE,
DSA_NOTIFIER_FDB_ADD,
DSA_NOTIFIER_FDB_DEL,
DSA_NOTIFIER_HOST_FDB_ADD,
DSA_NOTIFIER_HOST_FDB_DEL,
DSA_NOTIFIER_HSR_JOIN,
DSA_NOTIFIER_HSR_LEAVE,
DSA_NOTIFIER_LAG_CHANGE,
DSA_NOTIFIER_LAG_JOIN,
DSA_NOTIFIER_LAG_LEAVE,
DSA_NOTIFIER_MDB_ADD,
DSA_NOTIFIER_MDB_DEL,
DSA_NOTIFIER_HOST_MDB_ADD,
DSA_NOTIFIER_HOST_MDB_DEL,
DSA_NOTIFIER_VLAN_ADD,
DSA_NOTIFIER_VLAN_DEL,
DSA_NOTIFIER_MTU,
DSA_NOTIFIER_TAG_PROTO,
DSA_NOTIFIER_MRP_ADD,
DSA_NOTIFIER_MRP_DEL,
DSA_NOTIFIER_MRP_ADD_RING_ROLE,
DSA_NOTIFIER_MRP_DEL_RING_ROLE,
DSA_NOTIFIER_TAG_8021Q_VLAN_ADD,
DSA_NOTIFIER_TAG_8021Q_VLAN_DEL,
};
/* DSA_NOTIFIER_AGEING_TIME */
struct dsa_notifier_ageing_time_info {
unsigned int ageing_time;
};
/* DSA_NOTIFIER_BRIDGE_* */
struct dsa_notifier_bridge_info {
struct net_device *br;
int tree_index;
int sw_index;
int port;
};
/* DSA_NOTIFIER_FDB_* */
struct dsa_notifier_fdb_info {
int sw_index;
int port;
const unsigned char *addr;
u16 vid;
};
/* DSA_NOTIFIER_MDB_* */
struct dsa_notifier_mdb_info {
const struct switchdev_obj_port_mdb *mdb;
int sw_index;
int port;
};
/* DSA_NOTIFIER_LAG_* */
struct dsa_notifier_lag_info {
struct net_device *lag;
int sw_index;
int port;
struct netdev_lag_upper_info *info;
};
/* DSA_NOTIFIER_VLAN_* */
struct dsa_notifier_vlan_info {
const struct switchdev_obj_port_vlan *vlan;
int sw_index;
int port;
struct netlink_ext_ack *extack;
};
/* DSA_NOTIFIER_MTU */
struct dsa_notifier_mtu_info {
bool targeted_match;
int sw_index;
int port;
int mtu;
};
/* DSA_NOTIFIER_TAG_PROTO_* */
struct dsa_notifier_tag_proto_info {
const struct dsa_device_ops *tag_ops;
};
/* DSA_NOTIFIER_MRP_* */
struct dsa_notifier_mrp_info {
const struct switchdev_obj_mrp *mrp;
int sw_index;
int port;
};
/* DSA_NOTIFIER_MRP_* */
struct dsa_notifier_mrp_ring_role_info {
const struct switchdev_obj_ring_role_mrp *mrp;
int sw_index;
int port;
};
/* DSA_NOTIFIER_TAG_8021Q_VLAN_* */
struct dsa_notifier_tag_8021q_vlan_info {
int tree_index;
int sw_index;
int port;
u16 vid;
};
struct dsa_switchdev_event_work {
struct dsa_switch *ds;
int port;
struct net_device *dev;
struct work_struct work;
unsigned long event;
/* Specific for SWITCHDEV_FDB_ADD_TO_DEVICE and
* SWITCHDEV_FDB_DEL_TO_DEVICE
*/
unsigned char addr[ETH_ALEN];
u16 vid;
bool host_addr;
};
/* DSA_NOTIFIER_HSR_* */
struct dsa_notifier_hsr_info {
struct net_device *hsr;
int sw_index;
int port;
};
struct dsa_slave_priv {
/* Copy of CPU port xmit for faster access in slave transmit hot path */
struct sk_buff * (*xmit)(struct sk_buff *skb,
struct net_device *dev);
struct gro_cells gcells;
/* DSA port data, such as switch, port index, etc. */
struct dsa_port *dp;
#ifdef CONFIG_NET_POLL_CONTROLLER
struct netpoll *netpoll;
#endif
/* TC context */
struct list_head mall_tc_list;
};
/* dsa.c */
const struct dsa_device_ops *dsa_tag_driver_get(int tag_protocol);
void dsa_tag_driver_put(const struct dsa_device_ops *ops);
const struct dsa_device_ops *dsa_find_tagger_by_name(const char *buf);
bool dsa_schedule_work(struct work_struct *work);
const char *dsa_tag_protocol_to_str(const struct dsa_device_ops *ops);
static inline int dsa_tag_protocol_overhead(const struct dsa_device_ops *ops)
{
return ops->needed_headroom + ops->needed_tailroom;
}
/* master.c */
int dsa_master_setup(struct net_device *dev, struct dsa_port *cpu_dp);
void dsa_master_teardown(struct net_device *dev);
static inline struct net_device *dsa_master_find_slave(struct net_device *dev,
int device, int port)
{
struct dsa_port *cpu_dp = dev->dsa_ptr;
struct dsa_switch_tree *dst = cpu_dp->dst;
struct dsa_port *dp;
list_for_each_entry(dp, &dst->ports, list)
if (dp->ds->index == device && dp->index == port &&
dp->type == DSA_PORT_TYPE_USER)
return dp->slave;
return NULL;
}
/* port.c */
void dsa_port_set_tag_protocol(struct dsa_port *cpu_dp,
const struct dsa_device_ops *tag_ops);
int dsa_port_set_state(struct dsa_port *dp, u8 state, bool do_fast_age);
int dsa_port_enable_rt(struct dsa_port *dp, struct phy_device *phy);
int dsa_port_enable(struct dsa_port *dp, struct phy_device *phy);
void dsa_port_disable_rt(struct dsa_port *dp);
void dsa_port_disable(struct dsa_port *dp);
int dsa_port_bridge_join(struct dsa_port *dp, struct net_device *br,
struct netlink_ext_ack *extack);
void dsa_port_pre_bridge_leave(struct dsa_port *dp, struct net_device *br);
void dsa_port_bridge_leave(struct dsa_port *dp, struct net_device *br);
int dsa_port_lag_change(struct dsa_port *dp,
struct netdev_lag_lower_state_info *linfo);
int dsa_port_lag_join(struct dsa_port *dp, struct net_device *lag_dev,
struct netdev_lag_upper_info *uinfo,
struct netlink_ext_ack *extack);
void dsa_port_pre_lag_leave(struct dsa_port *dp, struct net_device *lag_dev);
void dsa_port_lag_leave(struct dsa_port *dp, struct net_device *lag_dev);
int dsa_port_vlan_filtering(struct dsa_port *dp, bool vlan_filtering,
struct netlink_ext_ack *extack);
bool dsa_port_skip_vlan_configuration(struct dsa_port *dp);
int dsa_port_ageing_time(struct dsa_port *dp, clock_t ageing_clock);
int dsa_port_mtu_change(struct dsa_port *dp, int new_mtu,
bool targeted_match);
int dsa_port_fdb_add(struct dsa_port *dp, const unsigned char *addr,
u16 vid);
int dsa_port_fdb_del(struct dsa_port *dp, const unsigned char *addr,
u16 vid);
int dsa_port_host_fdb_add(struct dsa_port *dp, const unsigned char *addr,
u16 vid);
int dsa_port_host_fdb_del(struct dsa_port *dp, const unsigned char *addr,
u16 vid);
int dsa_port_fdb_dump(struct dsa_port *dp, dsa_fdb_dump_cb_t *cb, void *data);
int dsa_port_mdb_add(const struct dsa_port *dp,
const struct switchdev_obj_port_mdb *mdb);
int dsa_port_mdb_del(const struct dsa_port *dp,
const struct switchdev_obj_port_mdb *mdb);
int dsa_port_host_mdb_add(const struct dsa_port *dp,
const struct switchdev_obj_port_mdb *mdb);
int dsa_port_host_mdb_del(const struct dsa_port *dp,
const struct switchdev_obj_port_mdb *mdb);
int dsa_port_pre_bridge_flags(const struct dsa_port *dp,
struct switchdev_brport_flags flags,
struct netlink_ext_ack *extack);
int dsa_port_bridge_flags(struct dsa_port *dp,
struct switchdev_brport_flags flags,
struct netlink_ext_ack *extack);
int dsa_port_vlan_add(struct dsa_port *dp,
const struct switchdev_obj_port_vlan *vlan,
struct netlink_ext_ack *extack);
int dsa_port_vlan_del(struct dsa_port *dp,
const struct switchdev_obj_port_vlan *vlan);
int dsa_port_mrp_add(const struct dsa_port *dp,
const struct switchdev_obj_mrp *mrp);
int dsa_port_mrp_del(const struct dsa_port *dp,
const struct switchdev_obj_mrp *mrp);
int dsa_port_mrp_add_ring_role(const struct dsa_port *dp,
const struct switchdev_obj_ring_role_mrp *mrp);
int dsa_port_mrp_del_ring_role(const struct dsa_port *dp,
const struct switchdev_obj_ring_role_mrp *mrp);
int dsa_port_link_register_of(struct dsa_port *dp);
void dsa_port_link_unregister_of(struct dsa_port *dp);
int dsa_port_hsr_join(struct dsa_port *dp, struct net_device *hsr);
void dsa_port_hsr_leave(struct dsa_port *dp, struct net_device *hsr);
int dsa_port_tag_8021q_vlan_add(struct dsa_port *dp, u16 vid, bool broadcast);
void dsa_port_tag_8021q_vlan_del(struct dsa_port *dp, u16 vid, bool broadcast);
extern const struct phylink_mac_ops dsa_port_phylink_mac_ops;
static inline bool dsa_port_offloads_bridge_port(struct dsa_port *dp,
const struct net_device *dev)
{
return dsa_port_to_bridge_port(dp) == dev;
}
static inline bool dsa_port_offloads_bridge(struct dsa_port *dp,
const struct net_device *bridge_dev)
{
/* DSA ports connected to a bridge, and event was emitted
* for the bridge.
*/
return dp->bridge_dev == bridge_dev;
}
/* Returns true if any port of this tree offloads the given net_device */
static inline bool dsa_tree_offloads_bridge_port(struct dsa_switch_tree *dst,
const struct net_device *dev)
{
struct dsa_port *dp;
list_for_each_entry(dp, &dst->ports, list)
if (dsa_port_offloads_bridge_port(dp, dev))
return true;
return false;
}
/* Returns true if any port of this tree offloads the given bridge */
static inline bool dsa_tree_offloads_bridge(struct dsa_switch_tree *dst,
const struct net_device *bridge_dev)
{
struct dsa_port *dp;
list_for_each_entry(dp, &dst->ports, list)
if (dsa_port_offloads_bridge(dp, bridge_dev))
return true;
return false;
}
/* slave.c */
extern const struct dsa_device_ops notag_netdev_ops;
extern struct notifier_block dsa_slave_switchdev_notifier;
extern struct notifier_block dsa_slave_switchdev_blocking_notifier;
void dsa_slave_mii_bus_init(struct dsa_switch *ds);
int dsa_slave_create(struct dsa_port *dp);
void dsa_slave_destroy(struct net_device *slave_dev);
int dsa_slave_suspend(struct net_device *slave_dev);
int dsa_slave_resume(struct net_device *slave_dev);
int dsa_slave_register_notifier(void);
void dsa_slave_unregister_notifier(void);
void dsa_slave_setup_tagger(struct net_device *slave);
int dsa_slave_change_mtu(struct net_device *dev, int new_mtu);
int dsa_slave_manage_vlan_filtering(struct net_device *dev,
bool vlan_filtering);
static inline struct dsa_port *dsa_slave_to_port(const struct net_device *dev)
{
struct dsa_slave_priv *p = netdev_priv(dev);
return p->dp;
}
static inline struct net_device *
dsa_slave_to_master(const struct net_device *dev)
{
struct dsa_port *dp = dsa_slave_to_port(dev);
return dp->cpu_dp->master;
}
/* If under a bridge with vlan_filtering=0, make sure to send pvid-tagged
* frames as untagged, since the bridge will not untag them.
*/
static inline struct sk_buff *dsa_untag_bridge_pvid(struct sk_buff *skb)
{
struct dsa_port *dp = dsa_slave_to_port(skb->dev);
struct net_device *br = dp->bridge_dev;
struct net_device *dev = skb->dev;
struct net_device *upper_dev;
u16 vid, pvid, proto;
int err;
if (!br || br_vlan_enabled(br))
return skb;
err = br_vlan_get_proto(br, &proto);
if (err)
return skb;
/* Move VLAN tag from data to hwaccel */
if (!skb_vlan_tag_present(skb) && skb->protocol == htons(proto)) {
skb = skb_vlan_untag(skb);
if (!skb)
return NULL;
}
if (!skb_vlan_tag_present(skb))
return skb;
vid = skb_vlan_tag_get_id(skb);
/* We already run under an RCU read-side critical section since
* we are called from netif_receive_skb_list_internal().
*/
err = br_vlan_get_pvid_rcu(dev, &pvid);
if (err)
return skb;
if (vid != pvid)
return skb;
/* The sad part about attempting to untag from DSA is that we
* don't know, unless we check, if the skb will end up in
* the bridge's data path - br_allowed_ingress() - or not.
* For example, there might be an 8021q upper for the
* default_pvid of the bridge, which will steal VLAN-tagged traffic
* from the bridge's data path. This is a configuration that DSA
* supports because vlan_filtering is 0. In that case, we should
* definitely keep the tag, to make sure it keeps working.
*/
upper_dev = __vlan_find_dev_deep_rcu(br, htons(proto), vid);
if (upper_dev)
return skb;
__vlan_hwaccel_clear_tag(skb);
return skb;
}
/* For switches without hardware support for DSA tagging to be able
* to support termination through the bridge.
*/
static inline struct net_device *
dsa_find_designated_bridge_port_by_vid(struct net_device *master, u16 vid)
{
struct dsa_port *cpu_dp = master->dsa_ptr;
struct dsa_switch_tree *dst = cpu_dp->dst;
struct bridge_vlan_info vinfo;
struct net_device *slave;
struct dsa_port *dp;
int err;
list_for_each_entry(dp, &dst->ports, list) {
if (dp->type != DSA_PORT_TYPE_USER)
continue;
if (!dp->bridge_dev)
continue;
if (dp->stp_state != BR_STATE_LEARNING &&
dp->stp_state != BR_STATE_FORWARDING)
continue;
/* Since the bridge might learn this packet, keep the CPU port
* affinity with the port that will be used for the reply on
* xmit.
*/
if (dp->cpu_dp != cpu_dp)
continue;
slave = dp->slave;
err = br_vlan_get_info_rcu(slave, vid, &vinfo);
if (err)
continue;
return slave;
}
return NULL;
}
/* If the ingress port offloads the bridge, we mark the frame as autonomously
* forwarded by hardware, so the software bridge doesn't forward in twice, back
* to us, because we already did. However, if we're in fallback mode and we do
* software bridging, we are not offloading it, therefore the dp->bridge_dev
* pointer is not populated, and flooding needs to be done by software (we are
* effectively operating in standalone ports mode).
*/
static inline void dsa_default_offload_fwd_mark(struct sk_buff *skb)
{
struct dsa_port *dp = dsa_slave_to_port(skb->dev);
skb->offload_fwd_mark = !!(dp->bridge_dev);
}
/* Helper for removing DSA header tags from packets in the RX path.
* Must not be called before skb_pull(len).
* skb->data
* |
* v
* | | | | | | | | | | | | | | | | | | |
* +-----------------------+-----------------------+---------------+-------+
* | Destination MAC | Source MAC | DSA header | EType |
* +-----------------------+-----------------------+---------------+-------+
* | |
* <----- len -----> <----- len ----->
* |
* >>>>>>> v
* >>>>>>> | | | | | | | | | | | | | | |
* >>>>>>> +-----------------------+-----------------------+-------+
* >>>>>>> | Destination MAC | Source MAC | EType |
* +-----------------------+-----------------------+-------+
* ^
* |
* skb->data
*/
static inline void dsa_strip_etype_header(struct sk_buff *skb, int len)
{
memmove(skb->data - ETH_HLEN, skb->data - ETH_HLEN - len, 2 * ETH_ALEN);
}
/* Helper for creating space for DSA header tags in TX path packets.
* Must not be called before skb_push(len).
*
* Before:
*
* <<<<<<< | | | | | | | | | | | | | | |
* ^ <<<<<<< +-----------------------+-----------------------+-------+
* | <<<<<<< | Destination MAC | Source MAC | EType |
* | +-----------------------+-----------------------+-------+
* <----- len ----->
* |
* |
* skb->data
*
* After:
*
* | | | | | | | | | | | | | | | | | | |
* +-----------------------+-----------------------+---------------+-------+
* | Destination MAC | Source MAC | DSA header | EType |
* +-----------------------+-----------------------+---------------+-------+
* ^ | |
* | <----- len ----->
* skb->data
*/
static inline void dsa_alloc_etype_header(struct sk_buff *skb, int len)
{
memmove(skb->data, skb->data + len, 2 * ETH_ALEN);
}
/* On RX, eth_type_trans() on the DSA master pulls ETH_HLEN bytes starting from
* skb_mac_header(skb), which leaves skb->data pointing at the first byte after
* what the DSA master perceives as the EtherType (the beginning of the L3
* protocol). Since DSA EtherType header taggers treat the EtherType as part of
* the DSA tag itself, and the EtherType is 2 bytes in length, the DSA header
* is located 2 bytes behind skb->data. Note that EtherType in this context
* means the first 2 bytes of the DSA header, not the encapsulated EtherType
* that will become visible after the DSA header is stripped.
*/
static inline void *dsa_etype_header_pos_rx(struct sk_buff *skb)
{
return skb->data - 2;
}
/* On TX, skb->data points to skb_mac_header(skb), which means that EtherType
* header taggers start exactly where the EtherType is (the EtherType is
* treated as part of the DSA header).
*/
static inline void *dsa_etype_header_pos_tx(struct sk_buff *skb)
{
return skb->data + 2 * ETH_ALEN;
}
/* switch.c */
int dsa_switch_register_notifier(struct dsa_switch *ds);
void dsa_switch_unregister_notifier(struct dsa_switch *ds);
/* dsa2.c */
void dsa_lag_map(struct dsa_switch_tree *dst, struct net_device *lag);
void dsa_lag_unmap(struct dsa_switch_tree *dst, struct net_device *lag);
int dsa_tree_notify(struct dsa_switch_tree *dst, unsigned long e, void *v);
int dsa_broadcast(unsigned long e, void *v);
int dsa_tree_change_tag_proto(struct dsa_switch_tree *dst,
struct net_device *master,
const struct dsa_device_ops *tag_ops,
const struct dsa_device_ops *old_tag_ops);
int dsa_bridge_num_get(const struct net_device *bridge_dev, int max);
void dsa_bridge_num_put(const struct net_device *bridge_dev, int bridge_num);
/* tag_8021q.c */
int dsa_tag_8021q_bridge_join(struct dsa_switch *ds,
struct dsa_notifier_bridge_info *info);
int dsa_tag_8021q_bridge_leave(struct dsa_switch *ds,
struct dsa_notifier_bridge_info *info);
int dsa_switch_tag_8021q_vlan_add(struct dsa_switch *ds,
struct dsa_notifier_tag_8021q_vlan_info *info);
int dsa_switch_tag_8021q_vlan_del(struct dsa_switch *ds,
struct dsa_notifier_tag_8021q_vlan_info *info);
extern struct list_head dsa_tree_list;
#endif
Reference in New Issue View Git Blame Copy Permalink