457a0955e1
Two simple test cases for interrupt endpoints are added to the usbtest.c file. These are simple non-queued interrupt IN and interrupt OUT transfers. Currently, only gadget zero is capable of executing the interrupt EP test cases. However, extending the same to other gadgets is extremely simple and can be done on-demand. The two new tests added are - Test 25: To verify Interrupt OUT transfer - Test 26: To verify Interrupt IN transfer Since the default value of wMaxPacketSize is set as 1024, so interrupt IN transfers must be specified with the size parameter = multiple of 1024. Otherwise the default value (512) in the usbtest application fails the transfer. See [RUN 4] for sample logs The application logs (usbtest) and corresponding kernel logs are as following: [Run 1] ./testusb -a -c 10 -s 2048 -t 26 -v 511 usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times [Run 2] ./testusb -a -c 10 -s 1024 -t 25 -v 511 usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times [Run 3] ./testusb -a -c 10 -s 1098 -t 25 -v 511 usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times [Run 4 - Failure case scenario] ./testusb -a -t 26 unknown speed /dev/bus/usb/007/004 0 /dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type) usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times usb 7-1: test26 failed, iterations left 999, status -75 (not 0) Signed-off-by: Amit Virdi <amit.virdi@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com> |
||
---|---|---|
.. | ||
atm | ||
c67x00 | ||
chipidea | ||
class | ||
common | ||
core | ||
dwc2 | ||
dwc3 | ||
early | ||
gadget | ||
host | ||
image | ||
misc | ||
mon | ||
musb | ||
phy | ||
renesas_usbhs | ||
serial | ||
storage | ||
wusbcore | ||
Kconfig | ||
Makefile | ||
README | ||
usb-skeleton.c |
To understand all the Linux-USB framework, you'll use these resources: * This source code. This is necessarily an evolving work, and includes kerneldoc that should help you get a current overview. ("make pdfdocs", and then look at "usb.pdf" for host side and "gadget.pdf" for peripheral side.) Also, Documentation/usb has more information. * The USB 2.0 specification (from www.usb.org), with supplements such as those for USB OTG and the various device classes. The USB specification has a good overview chapter, and USB peripherals conform to the widely known "Chapter 9". * Chip specifications for USB controllers. Examples include host controllers (on PCs, servers, and more); peripheral controllers (in devices with Linux firmware, like printers or cell phones); and hard-wired peripherals like Ethernet adapters. * Specifications for other protocols implemented by USB peripheral functions. Some are vendor-specific; others are vendor-neutral but just standardized outside of the www.usb.org team. Here is a list of what each subdirectory here is, and what is contained in them. core/ - This is for the core USB host code, including the usbfs files and the hub class driver ("khubd"). host/ - This is for USB host controller drivers. This includes UHCI, OHCI, EHCI, and others that might be used with more specialized "embedded" systems. gadget/ - This is for USB peripheral controller drivers and the various gadget drivers which talk to them. Individual USB driver directories. A new driver should be added to the first subdirectory in the list below that it fits into. image/ - This is for still image drivers, like scanners or digital cameras. ../input/ - This is for any driver that uses the input subsystem, like keyboard, mice, touchscreens, tablets, etc. ../media/ - This is for multimedia drivers, like video cameras, radios, and any other drivers that talk to the v4l subsystem. ../net/ - This is for network drivers. serial/ - This is for USB to serial drivers. storage/ - This is for USB mass-storage drivers. class/ - This is for all USB device drivers that do not fit into any of the above categories, and work for a range of USB Class specified devices. misc/ - This is for all USB device drivers that do not fit into any of the above categories.