cba63cf8f9
The default used to be that the first vivid device instance was single planar, the second multi planar, the third single planar, etc. However, that turned out to be unexpected and awkward. Change the driver to always default to single planar. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> |
||
|---|---|---|
| .. | ||
| bttv | ||
| cx88 | ||
| cx2341x | ||
| 4CCs.txt | ||
| API.html | ||
| cafe_ccic | ||
| CARDLIST.au0828 | ||
| CARDLIST.bttv | ||
| CARDLIST.cx88 | ||
| CARDLIST.cx23885 | ||
| CARDLIST.em28xx | ||
| CARDLIST.ivtv | ||
| CARDLIST.saa7134 | ||
| CARDLIST.saa7164 | ||
| CARDLIST.tm6000 | ||
| CARDLIST.tuner | ||
| CARDLIST.usbvision | ||
| cpia2_overview.txt | ||
| CQcam.txt | ||
| cx18.txt | ||
| extract_xc3028.pl | ||
| fimc.txt | ||
| gspca.txt | ||
| hauppauge-wintv-cx88-ir.txt | ||
| lifeview.txt | ||
| Makefile | ||
| meye.txt | ||
| not-in-cx2388x-datasheet.txt | ||
| omap3isp.txt | ||
| omap4_camera.txt | ||
| pxa_camera.txt | ||
| radiotrack.txt | ||
| README.cpia2 | ||
| README.cx88 | ||
| README.davinci-vpbe | ||
| README.ir | ||
| README.ivtv | ||
| README.pvrusb2 | ||
| README.saa7134 | ||
| README.tlg2300 | ||
| sh_mobile_ceu_camera.txt | ||
| si470x.txt | ||
| si476x.txt | ||
| si4713.txt | ||
| soc-camera.txt | ||
| uvcvideo.txt | ||
| v4l2-controls.txt | ||
| v4l2-framework.txt | ||
| v4l2-pci-skeleton.c | ||
| videobuf | ||
| vivid.txt | ||
| w9966.txt | ||
| Zoran | ||
| zr364xx.txt | ||
tlg2300 release notes ==================== This is a v4l2/dvb device driver for the tlg2300 chip. current status ============== video - support mmap and read().(no overlay) audio - The driver will register a ALSA card for the audio input. vbi - Works for almost TV norms. dvb-t - works for DVB-T FM - Works for radio. --------------------------------------------------------------------------- TESTED APPLICATIONS: -VLC1.0.4 test the video and dvb. The GUI is friendly to use. -Mplayer test the video. -Mplayer test the FM. The mplayer should be compiled with --enable-radio and --enable-radio-capture. The command runs as this(The alsa audio registers to card 1): #mplayer radio://103.7/capture/ -radio adevice=hw=1,0:arate=48000 \ -rawaudio rate=48000:channels=2 --------------------------------------------------------------------------- KNOWN PROBLEMS: about preemphasis: You can set the preemphasis for radio by the following command: #v4l2-ctl -d /dev/radio0 --set-ctrl=pre_emphasis_settings=1 "pre_emphasis_settings=1" means that you select the 50us. If you want to select the 75us, please use "pre_emphasis_settings=2"