56cd4b9e8c
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together with its function definitions in sama5d2.dtsi. Boards will just fill the pins and enable the desired functions. There is a single functional change in this patch. With the move of the flx0 uart5 definition in the SoC dtsi, the uart5 from at91-sama5d27_wlsom1_ek.dts inherits the following optional property: atmel,fifo-size = <32>; This particular change was tested by Codrin. Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20200514050301.147442-7-tudor.ambarus@microchip.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
435 lines
8.9 KiB
Plaintext
435 lines
8.9 KiB
Plaintext
// SPDX-License-Identifier: (GPL-2.0+ OR X11)
|
|
/*
|
|
* at91-sama5d2_ptc_ek.dts - Device Tree file for SAMA5D2 PTC EK board
|
|
*
|
|
* Copyright (C) 2017 Microchip/Atmel,
|
|
* 2017 Wenyou Yang <wenyou.yang@microchip.com>
|
|
* 2017 Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
*/
|
|
/dts-v1/;
|
|
#include "sama5d2.dtsi"
|
|
#include "sama5d2-pinfunc.h"
|
|
#include <dt-bindings/mfd/atmel-flexcom.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/pinctrl/at91.h>
|
|
|
|
/ {
|
|
model = "Atmel SAMA5D2 PTC EK";
|
|
compatible = "atmel,sama5d2-ptc_ek", "atmel,sama5d2", "atmel,sama5";
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
i2c0 = &i2c0;
|
|
i2c1 = &i2c1;
|
|
i2c2 = &i2c2;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
clocks {
|
|
slow_xtal {
|
|
clock-frequency = <32768>;
|
|
};
|
|
|
|
main_xtal {
|
|
clock-frequency = <24000000>;
|
|
};
|
|
};
|
|
|
|
ahb {
|
|
usb0: gadget@300000 {
|
|
atmel,vbus-gpio = <&pioA PIN_PB11 GPIO_ACTIVE_HIGH>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usba_vbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
usb1: ohci@400000 {
|
|
num-ports = <3>;
|
|
atmel,vbus-gpio = <0
|
|
&pioA PIN_PB12 GPIO_ACTIVE_HIGH
|
|
0
|
|
>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_usb_default>;
|
|
status = "okay";
|
|
};
|
|
|
|
usb2: ehci@500000 {
|
|
status = "okay";
|
|
};
|
|
|
|
ebi: ebi@10000000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_nand_default>;
|
|
status = "okay"; /* conflicts with sdmmc1 and qspi0 */
|
|
|
|
nand_controller: nand-controller {
|
|
status = "okay";
|
|
|
|
nand@3 {
|
|
reg = <0x3 0x0 0x2>;
|
|
atmel,rb = <0>;
|
|
nand-bus-width = <8>;
|
|
nand-ecc-mode = "hw";
|
|
nand-on-flash-bbt;
|
|
label = "atmel_nand";
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
at91bootstrap@0 {
|
|
label = "bootstrap";
|
|
reg = <0x0 0x40000>;
|
|
};
|
|
|
|
bootloader@40000 {
|
|
label = "bootloader";
|
|
reg = <0x40000 0xc0000>;
|
|
};
|
|
|
|
bootloaderenvred@0x100000 {
|
|
label = "bootloader env redundant";
|
|
reg = <0x100000 0x40000>;
|
|
};
|
|
|
|
bootloaderenv@0x140000 {
|
|
label = "bootloader env";
|
|
reg = <0x140000 0x40000>;
|
|
};
|
|
|
|
dtb@180000 {
|
|
label = "device tree";
|
|
reg = <0x180000 0x80000>;
|
|
};
|
|
|
|
kernel@200000 {
|
|
label = "kernel";
|
|
reg = <0x200000 0x600000>;
|
|
};
|
|
|
|
rootfs@800000 {
|
|
label = "rootfs";
|
|
reg = <0x800000 0x1f800000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
sdmmc0: sdio-host@a0000000 {
|
|
bus-width = <8>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_sdmmc0_default>;
|
|
status = "okay";
|
|
};
|
|
|
|
apb {
|
|
spi0: spi@f8000000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_spi0_default>;
|
|
status = "okay";
|
|
};
|
|
|
|
macb0: ethernet@f8008000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
|
|
phy-mode = "rmii";
|
|
status = "okay";
|
|
|
|
ethernet-phy@1 {
|
|
reg = <0x1>;
|
|
interrupt-parent = <&pioA>;
|
|
interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
|
|
};
|
|
};
|
|
|
|
tcb0: timer@f800c000 {
|
|
timer0: timer@0 {
|
|
compatible = "atmel,tcb-timer";
|
|
reg = <0>;
|
|
};
|
|
|
|
timer1: timer@1 {
|
|
compatible = "atmel,tcb-timer";
|
|
reg = <1>;
|
|
};
|
|
};
|
|
|
|
uart0: serial@f801c000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart0_default>;
|
|
atmel,use-dma-rx;
|
|
atmel,use-dma-tx;
|
|
status = "okay";
|
|
};
|
|
|
|
uart2: serial@f8024000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_uart2_default>;
|
|
atmel,use-dma-rx;
|
|
atmel,use-dma-tx;
|
|
status = "okay";
|
|
};
|
|
|
|
i2c0: i2c@f8028000 {
|
|
dmas = <0>, <0>;
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c0_default>;
|
|
pinctrl-1 = <&pinctrl_i2c0_gpio>;
|
|
sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
|
|
scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
|
|
flx0: flexcom@f8034000 {
|
|
atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
|
|
status = "okay";
|
|
|
|
i2c2: i2c@600 {
|
|
dmas = <0>, <0>;
|
|
dma-names = "tx", "rx";
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_flx0_default>;
|
|
pinctrl-1 = <&pinctrl_flx0_gpio>;
|
|
sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
|
|
scl-gpios = <&pioA PIN_PB29 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
shdwc@f8048010 {
|
|
atmel,shdwc-debouncer = <976>;
|
|
|
|
input@0 {
|
|
reg = <0>;
|
|
atmel,wakeup-type = "low";
|
|
};
|
|
};
|
|
|
|
watchdog@f8048040 {
|
|
status = "okay";
|
|
};
|
|
|
|
spi1: spi@fc000000 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_spi1_default>;
|
|
status = "okay";
|
|
};
|
|
|
|
i2c1: i2c@fc028000 {
|
|
dmas = <0>, <0>;
|
|
pinctrl-names = "default", "gpio";
|
|
pinctrl-0 = <&pinctrl_i2c1_default>;
|
|
pinctrl-1 = <&pinctrl_i2c1_gpio>;
|
|
sda-gpios = <&pioA PIN_PC6 GPIO_ACTIVE_HIGH>;
|
|
scl-gpios = <&pioA PIN_PC7 GPIO_ACTIVE_HIGH>;
|
|
status = "okay";
|
|
|
|
at24@50 {
|
|
compatible = "atmel,24c02";
|
|
reg = <0x50>;
|
|
pagesize = <8>;
|
|
};
|
|
};
|
|
|
|
pinctrl@fc038000 {
|
|
pinctrl_flx0_default: flx0_default {
|
|
pinmux = <PIN_PB28__FLEXCOM0_IO0>,
|
|
<PIN_PB29__FLEXCOM0_IO1>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_flx0_gpio: flx0_gpio {
|
|
pinmux = <PIN_PB28__GPIO>,
|
|
<PIN_PB29__GPIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_i2c0_default: i2c0_default {
|
|
pinmux = <PIN_PD21__TWD0>,
|
|
<PIN_PD22__TWCK0>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_i2c0_gpio: i2c0_gpio {
|
|
pinmux = <PIN_PD21__GPIO>,
|
|
<PIN_PD22__GPIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_i2c1_default: i2c1_default {
|
|
pinmux = <PIN_PC6__TWD1>,
|
|
<PIN_PC7__TWCK1>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_i2c1_gpio: i2c1_gpio {
|
|
pinmux = <PIN_PC6__GPIO>,
|
|
<PIN_PC7__GPIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_key_gpio_default: key_gpio_default {
|
|
pinmux = <PIN_PA10__GPIO>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
pinctrl_led_gpio_default: led_gpio_default {
|
|
pinmux = <PIN_PB6__GPIO>,
|
|
<PIN_PB8__GPIO>,
|
|
<PIN_PB10__GPIO>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
pinctrl_macb0_default: macb0_default {
|
|
pinmux = <PIN_PB14__GTXCK>,
|
|
<PIN_PB15__GTXEN>,
|
|
<PIN_PB16__GRXDV>,
|
|
<PIN_PB17__GRXER>,
|
|
<PIN_PB18__GRX0>,
|
|
<PIN_PB19__GRX1>,
|
|
<PIN_PB20__GTX0>,
|
|
<PIN_PB21__GTX1>,
|
|
<PIN_PB22__GMDC>,
|
|
<PIN_PB23__GMDIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_macb0_phy_irq: macb0_phy_irq {
|
|
pinmux = <PIN_PB24__GPIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_nand_default: nand_default {
|
|
re_we_data {
|
|
pinmux = <PIN_PA22__D0>,
|
|
<PIN_PA23__D1>,
|
|
<PIN_PA24__D2>,
|
|
<PIN_PA25__D3>,
|
|
<PIN_PA26__D4>,
|
|
<PIN_PA27__D5>,
|
|
<PIN_PA28__D6>,
|
|
<PIN_PA29__D7>,
|
|
<PIN_PA30__NWE_NANDWE>,
|
|
<PIN_PB2__NRD_NANDOE>;
|
|
bias-pull-up;
|
|
atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
|
|
};
|
|
|
|
ale_cle_rdy_cs {
|
|
pinmux = <PIN_PB0__A21_NANDALE>,
|
|
<PIN_PB1__A22_NANDCLE>,
|
|
<PIN_PC8__NANDRDY>,
|
|
<PIN_PA31__NCS3>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
pinctrl_sdmmc0_default: sdmmc0_default {
|
|
cmd_data {
|
|
pinmux = <PIN_PA1__SDMMC0_CMD>,
|
|
<PIN_PA2__SDMMC0_DAT0>,
|
|
<PIN_PA3__SDMMC0_DAT1>,
|
|
<PIN_PA4__SDMMC0_DAT2>,
|
|
<PIN_PA5__SDMMC0_DAT3>,
|
|
<PIN_PA6__SDMMC0_DAT4>,
|
|
<PIN_PA7__SDMMC0_DAT5>,
|
|
<PIN_PA8__SDMMC0_DAT6>,
|
|
<PIN_PA9__SDMMC0_DAT7>;
|
|
bias-pull-up;
|
|
};
|
|
|
|
ck_cd_vddsel {
|
|
pinmux = <PIN_PA0__SDMMC0_CK>,
|
|
<PIN_PA11__SDMMC0_VDDSEL>,
|
|
<PIN_PA13__SDMMC0_CD>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
pinctrl_spi0_default: spi0_default {
|
|
pinmux = <PIN_PA14__SPI0_SPCK>,
|
|
<PIN_PA15__SPI0_MOSI>,
|
|
<PIN_PA16__SPI0_MISO>,
|
|
<PIN_PA17__SPI0_NPCS0>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_spi1_default: spi1_default {
|
|
pinmux = <PIN_PC1__SPI1_SPCK>,
|
|
<PIN_PC2__SPI1_MOSI>,
|
|
<PIN_PC3__SPI1_MISO>,
|
|
<PIN_PC4__SPI1_NPCS0>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_uart0_default: uart0_default {
|
|
pinmux = <PIN_PB26__URXD0>,
|
|
<PIN_PB27__UTXD0>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_uart2_default: uart2_default {
|
|
pinmux = <PIN_PD23__URXD2>,
|
|
<PIN_PD24__UTXD2>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_usb_default: usb_default {
|
|
pinmux = <PIN_PB12__GPIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinctrl_usba_vbus: usba_vbus {
|
|
pinmux = <PIN_PB11__GPIO>;
|
|
bias-disable;
|
|
};
|
|
|
|
};
|
|
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_key_gpio_default>;
|
|
|
|
bp1 {
|
|
label = "PB_USER";
|
|
gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>;
|
|
linux,code = <0x104>;
|
|
wakeup-source;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&pinctrl_led_gpio_default>;
|
|
status = "okay";
|
|
|
|
red {
|
|
label = "red";
|
|
gpios = <&pioA PIN_PB10 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
green {
|
|
label = "green";
|
|
gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
blue {
|
|
label = "blue";
|
|
gpios = <&pioA PIN_PB6 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
};
|
|
};
|