Stress tests show that DSP may occasionally be late with signaling WAIT state when all pins are made use of simultaneously plus start/stop (pause) gets involved. While this isn't tied to standard audio scenarios where only System Pin (playback and capture) is involved, ensure user is not hindered when playing with more advanced scenarios. >From DSP perspective, clock acts as a resource: low clock equals less resources, high clock more resources. Relax clock selection procedure so only low -> high switch is allowed when awaiting WAIT signal times out. Once active stream count decreases, DSP will have more time internally to adjust thus low clock selection becomes possible again. Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://lore.kernel.org/r/20201012103221.30759-2-cezary.rojewski@intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
582 lines
16 KiB
C
582 lines
16 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
//
|
|
// Copyright(c) 2020 Intel Corporation. All rights reserved.
|
|
//
|
|
// Author: Cezary Rojewski <cezary.rojewski@intel.com>
|
|
//
|
|
|
|
#include <linux/devcoredump.h>
|
|
#include <linux/dma-mapping.h>
|
|
#include <linux/firmware.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/pxa2xx_ssp.h>
|
|
#include "core.h"
|
|
#include "messages.h"
|
|
#include "registers.h"
|
|
|
|
static bool catpt_dma_filter(struct dma_chan *chan, void *param)
|
|
{
|
|
return param == chan->device->dev;
|
|
}
|
|
|
|
/*
|
|
* Either engine 0 or 1 can be used for image loading.
|
|
* Align with Windows driver equivalent and stick to engine 1.
|
|
*/
|
|
#define CATPT_DMA_DEVID 1
|
|
#define CATPT_DMA_DSP_ADDR_MASK GENMASK(31, 20)
|
|
|
|
struct dma_chan *catpt_dma_request_config_chan(struct catpt_dev *cdev)
|
|
{
|
|
struct dma_slave_config config;
|
|
struct dma_chan *chan;
|
|
dma_cap_mask_t mask;
|
|
int ret;
|
|
|
|
dma_cap_zero(mask);
|
|
dma_cap_set(DMA_MEMCPY, mask);
|
|
|
|
chan = dma_request_channel(mask, catpt_dma_filter, cdev->dev);
|
|
if (!chan) {
|
|
dev_err(cdev->dev, "request channel failed\n");
|
|
return ERR_PTR(-ENODEV);
|
|
}
|
|
|
|
memset(&config, 0, sizeof(config));
|
|
config.direction = DMA_MEM_TO_DEV;
|
|
config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
|
|
config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
|
|
config.src_maxburst = 16;
|
|
config.dst_maxburst = 16;
|
|
|
|
ret = dmaengine_slave_config(chan, &config);
|
|
if (ret) {
|
|
dev_err(cdev->dev, "slave config failed: %d\n", ret);
|
|
dma_release_channel(chan);
|
|
return ERR_PTR(ret);
|
|
}
|
|
|
|
return chan;
|
|
}
|
|
|
|
static int catpt_dma_memcpy(struct catpt_dev *cdev, struct dma_chan *chan,
|
|
dma_addr_t dst_addr, dma_addr_t src_addr,
|
|
size_t size)
|
|
{
|
|
struct dma_async_tx_descriptor *desc;
|
|
enum dma_status status;
|
|
|
|
desc = dmaengine_prep_dma_memcpy(chan, dst_addr, src_addr, size,
|
|
DMA_CTRL_ACK);
|
|
if (!desc) {
|
|
dev_err(cdev->dev, "prep dma memcpy failed\n");
|
|
return -EIO;
|
|
}
|
|
|
|
/* enable demand mode for dma channel */
|
|
catpt_updatel_shim(cdev, HMDC,
|
|
CATPT_HMDC_HDDA(CATPT_DMA_DEVID, chan->chan_id),
|
|
CATPT_HMDC_HDDA(CATPT_DMA_DEVID, chan->chan_id));
|
|
dmaengine_submit(desc);
|
|
status = dma_wait_for_async_tx(desc);
|
|
/* regardless of status, disable access to HOST memory in demand mode */
|
|
catpt_updatel_shim(cdev, HMDC,
|
|
CATPT_HMDC_HDDA(CATPT_DMA_DEVID, chan->chan_id), 0);
|
|
|
|
return (status == DMA_COMPLETE) ? 0 : -EPROTO;
|
|
}
|
|
|
|
int catpt_dma_memcpy_todsp(struct catpt_dev *cdev, struct dma_chan *chan,
|
|
dma_addr_t dst_addr, dma_addr_t src_addr,
|
|
size_t size)
|
|
{
|
|
return catpt_dma_memcpy(cdev, chan, dst_addr | CATPT_DMA_DSP_ADDR_MASK,
|
|
src_addr, size);
|
|
}
|
|
|
|
int catpt_dma_memcpy_fromdsp(struct catpt_dev *cdev, struct dma_chan *chan,
|
|
dma_addr_t dst_addr, dma_addr_t src_addr,
|
|
size_t size)
|
|
{
|
|
return catpt_dma_memcpy(cdev, chan, dst_addr,
|
|
src_addr | CATPT_DMA_DSP_ADDR_MASK, size);
|
|
}
|
|
|
|
int catpt_dmac_probe(struct catpt_dev *cdev)
|
|
{
|
|
struct dw_dma_chip *dmac;
|
|
int ret;
|
|
|
|
dmac = devm_kzalloc(cdev->dev, sizeof(*dmac), GFP_KERNEL);
|
|
if (!dmac)
|
|
return -ENOMEM;
|
|
|
|
dmac->regs = cdev->lpe_ba + cdev->spec->host_dma_offset[CATPT_DMA_DEVID];
|
|
dmac->dev = cdev->dev;
|
|
dmac->irq = cdev->irq;
|
|
|
|
ret = dma_coerce_mask_and_coherent(cdev->dev, DMA_BIT_MASK(31));
|
|
if (ret)
|
|
return ret;
|
|
/*
|
|
* Caller is responsible for putting device in D0 to allow
|
|
* for I/O and memory access before probing DW.
|
|
*/
|
|
ret = dw_dma_probe(dmac);
|
|
if (ret)
|
|
return ret;
|
|
|
|
cdev->dmac = dmac;
|
|
return 0;
|
|
}
|
|
|
|
void catpt_dmac_remove(struct catpt_dev *cdev)
|
|
{
|
|
/*
|
|
* As do_dma_remove() juggles with pm_runtime_get_xxx() and
|
|
* pm_runtime_put_xxx() while both ADSP and DW 'devices' are part of
|
|
* the same module, caller makes sure pm_runtime_disable() is invoked
|
|
* before removing DW to prevent postmortem resume and suspend.
|
|
*/
|
|
dw_dma_remove(cdev->dmac);
|
|
}
|
|
|
|
static void catpt_dsp_set_srampge(struct catpt_dev *cdev, struct resource *sram,
|
|
unsigned long mask, unsigned long new)
|
|
{
|
|
unsigned long old;
|
|
u32 off = sram->start;
|
|
u32 b = __ffs(mask);
|
|
|
|
old = catpt_readl_pci(cdev, VDRTCTL0) & mask;
|
|
dev_dbg(cdev->dev, "SRAMPGE [0x%08lx] 0x%08lx -> 0x%08lx",
|
|
mask, old, new);
|
|
|
|
if (old == new)
|
|
return;
|
|
|
|
catpt_updatel_pci(cdev, VDRTCTL0, mask, new);
|
|
/* wait for SRAM power gating to propagate */
|
|
udelay(60);
|
|
|
|
/*
|
|
* Dummy read as the very first access after block enable
|
|
* to prevent byte loss in future operations.
|
|
*/
|
|
for_each_clear_bit_from(b, &new, fls_long(mask)) {
|
|
u8 buf[4];
|
|
|
|
/* newly enabled: new bit=0 while old bit=1 */
|
|
if (test_bit(b, &old)) {
|
|
dev_dbg(cdev->dev, "sanitize block %ld: off 0x%08x\n",
|
|
b - __ffs(mask), off);
|
|
memcpy_fromio(buf, cdev->lpe_ba + off, sizeof(buf));
|
|
}
|
|
off += CATPT_MEMBLOCK_SIZE;
|
|
}
|
|
}
|
|
|
|
void catpt_dsp_update_srampge(struct catpt_dev *cdev, struct resource *sram,
|
|
unsigned long mask)
|
|
{
|
|
struct resource *res;
|
|
unsigned long new = 0;
|
|
|
|
/* flag all busy blocks */
|
|
for (res = sram->child; res; res = res->sibling) {
|
|
u32 h, l;
|
|
|
|
h = (res->end - sram->start) / CATPT_MEMBLOCK_SIZE;
|
|
l = (res->start - sram->start) / CATPT_MEMBLOCK_SIZE;
|
|
new |= GENMASK(h, l);
|
|
}
|
|
|
|
/* offset value given mask's start and invert it as ON=b0 */
|
|
new = ~(new << __ffs(mask)) & mask;
|
|
|
|
/* disable core clock gating */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DCLCGE, 0);
|
|
|
|
catpt_dsp_set_srampge(cdev, sram, mask, new);
|
|
|
|
/* enable core clock gating */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DCLCGE,
|
|
CATPT_VDRTCTL2_DCLCGE);
|
|
}
|
|
|
|
int catpt_dsp_stall(struct catpt_dev *cdev, bool stall)
|
|
{
|
|
u32 reg, val;
|
|
|
|
val = stall ? CATPT_CS_STALL : 0;
|
|
catpt_updatel_shim(cdev, CS1, CATPT_CS_STALL, val);
|
|
|
|
return catpt_readl_poll_shim(cdev, CS1,
|
|
reg, (reg & CATPT_CS_STALL) == val,
|
|
500, 10000);
|
|
}
|
|
|
|
static int catpt_dsp_reset(struct catpt_dev *cdev, bool reset)
|
|
{
|
|
u32 reg, val;
|
|
|
|
val = reset ? CATPT_CS_RST : 0;
|
|
catpt_updatel_shim(cdev, CS1, CATPT_CS_RST, val);
|
|
|
|
return catpt_readl_poll_shim(cdev, CS1,
|
|
reg, (reg & CATPT_CS_RST) == val,
|
|
500, 10000);
|
|
}
|
|
|
|
void lpt_dsp_pll_shutdown(struct catpt_dev *cdev, bool enable)
|
|
{
|
|
u32 val;
|
|
|
|
val = enable ? LPT_VDRTCTL0_APLLSE : 0;
|
|
catpt_updatel_pci(cdev, VDRTCTL0, LPT_VDRTCTL0_APLLSE, val);
|
|
}
|
|
|
|
void wpt_dsp_pll_shutdown(struct catpt_dev *cdev, bool enable)
|
|
{
|
|
u32 val;
|
|
|
|
val = enable ? WPT_VDRTCTL2_APLLSE : 0;
|
|
catpt_updatel_pci(cdev, VDRTCTL2, WPT_VDRTCTL2_APLLSE, val);
|
|
}
|
|
|
|
static int catpt_dsp_select_lpclock(struct catpt_dev *cdev, bool lp, bool waiti)
|
|
{
|
|
u32 mask, reg, val;
|
|
int ret;
|
|
|
|
mutex_lock(&cdev->clk_mutex);
|
|
|
|
val = lp ? CATPT_CS_LPCS : 0;
|
|
reg = catpt_readl_shim(cdev, CS1) & CATPT_CS_LPCS;
|
|
dev_dbg(cdev->dev, "LPCS [0x%08lx] 0x%08x -> 0x%08x",
|
|
CATPT_CS_LPCS, reg, val);
|
|
|
|
if (reg == val) {
|
|
mutex_unlock(&cdev->clk_mutex);
|
|
return 0;
|
|
}
|
|
|
|
if (waiti) {
|
|
/* wait for DSP to signal WAIT state */
|
|
ret = catpt_readl_poll_shim(cdev, ISD,
|
|
reg, (reg & CATPT_ISD_DCPWM),
|
|
500, 10000);
|
|
if (ret) {
|
|
dev_warn(cdev->dev, "await WAITI timeout\n");
|
|
/* no signal - only high clock selection allowed */
|
|
if (lp) {
|
|
mutex_unlock(&cdev->clk_mutex);
|
|
return 0;
|
|
}
|
|
}
|
|
}
|
|
|
|
ret = catpt_readl_poll_shim(cdev, CLKCTL,
|
|
reg, !(reg & CATPT_CLKCTL_CFCIP),
|
|
500, 10000);
|
|
if (ret)
|
|
dev_warn(cdev->dev, "clock change still in progress\n");
|
|
|
|
/* default to DSP core & audio fabric high clock */
|
|
val |= CATPT_CS_DCS_HIGH;
|
|
mask = CATPT_CS_LPCS | CATPT_CS_DCS;
|
|
catpt_updatel_shim(cdev, CS1, mask, val);
|
|
|
|
ret = catpt_readl_poll_shim(cdev, CLKCTL,
|
|
reg, !(reg & CATPT_CLKCTL_CFCIP),
|
|
500, 10000);
|
|
if (ret)
|
|
dev_warn(cdev->dev, "clock change still in progress\n");
|
|
|
|
/* update PLL accordingly */
|
|
cdev->spec->pll_shutdown(cdev, lp);
|
|
|
|
mutex_unlock(&cdev->clk_mutex);
|
|
return 0;
|
|
}
|
|
|
|
int catpt_dsp_update_lpclock(struct catpt_dev *cdev)
|
|
{
|
|
struct catpt_stream_runtime *stream;
|
|
|
|
list_for_each_entry(stream, &cdev->stream_list, node)
|
|
if (stream->prepared)
|
|
return catpt_dsp_select_lpclock(cdev, false, true);
|
|
|
|
return catpt_dsp_select_lpclock(cdev, true, true);
|
|
}
|
|
|
|
/* bring registers to their defaults as HW won't reset itself */
|
|
static void catpt_dsp_set_regs_defaults(struct catpt_dev *cdev)
|
|
{
|
|
int i;
|
|
|
|
catpt_writel_shim(cdev, CS1, CATPT_CS_DEFAULT);
|
|
catpt_writel_shim(cdev, ISC, CATPT_ISC_DEFAULT);
|
|
catpt_writel_shim(cdev, ISD, CATPT_ISD_DEFAULT);
|
|
catpt_writel_shim(cdev, IMC, CATPT_IMC_DEFAULT);
|
|
catpt_writel_shim(cdev, IMD, CATPT_IMD_DEFAULT);
|
|
catpt_writel_shim(cdev, IPCC, CATPT_IPCC_DEFAULT);
|
|
catpt_writel_shim(cdev, IPCD, CATPT_IPCD_DEFAULT);
|
|
catpt_writel_shim(cdev, CLKCTL, CATPT_CLKCTL_DEFAULT);
|
|
catpt_writel_shim(cdev, CS2, CATPT_CS2_DEFAULT);
|
|
catpt_writel_shim(cdev, LTRC, CATPT_LTRC_DEFAULT);
|
|
catpt_writel_shim(cdev, HMDC, CATPT_HMDC_DEFAULT);
|
|
|
|
for (i = 0; i < CATPT_SSP_COUNT; i++) {
|
|
catpt_writel_ssp(cdev, i, SSCR0, CATPT_SSC0_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSCR1, CATPT_SSC1_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSSR, CATPT_SSS_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSITR, CATPT_SSIT_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSDR, CATPT_SSD_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSTO, CATPT_SSTO_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSPSP, CATPT_SSPSP_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSTSA, CATPT_SSTSA_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSRSA, CATPT_SSRSA_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSTSS, CATPT_SSTSS_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSCR2, CATPT_SSCR2_DEFAULT);
|
|
catpt_writel_ssp(cdev, i, SSPSP2, CATPT_SSPSP2_DEFAULT);
|
|
}
|
|
}
|
|
|
|
int lpt_dsp_power_down(struct catpt_dev *cdev)
|
|
{
|
|
catpt_dsp_reset(cdev, true);
|
|
|
|
/* set 24Mhz clock for both SSPs */
|
|
catpt_updatel_shim(cdev, CS1, CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1),
|
|
CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1));
|
|
catpt_dsp_select_lpclock(cdev, true, false);
|
|
|
|
/* DRAM power gating all */
|
|
catpt_dsp_set_srampge(cdev, &cdev->dram, cdev->spec->dram_mask,
|
|
cdev->spec->dram_mask);
|
|
catpt_dsp_set_srampge(cdev, &cdev->iram, cdev->spec->iram_mask,
|
|
cdev->spec->iram_mask);
|
|
|
|
catpt_updatel_pci(cdev, PMCS, PCI_PM_CTRL_STATE_MASK, PCI_D3hot);
|
|
/* give hw time to drop off */
|
|
udelay(50);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int lpt_dsp_power_up(struct catpt_dev *cdev)
|
|
{
|
|
/* SRAM power gating none */
|
|
catpt_dsp_set_srampge(cdev, &cdev->dram, cdev->spec->dram_mask, 0);
|
|
catpt_dsp_set_srampge(cdev, &cdev->iram, cdev->spec->iram_mask, 0);
|
|
|
|
catpt_updatel_pci(cdev, PMCS, PCI_PM_CTRL_STATE_MASK, PCI_D0);
|
|
/* give hw time to wake up */
|
|
udelay(100);
|
|
|
|
catpt_dsp_select_lpclock(cdev, false, false);
|
|
catpt_updatel_shim(cdev, CS1,
|
|
CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1),
|
|
CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1));
|
|
/* stagger DSP reset after clock selection */
|
|
udelay(50);
|
|
|
|
catpt_dsp_reset(cdev, false);
|
|
/* generate int deassert msg to fix inversed int logic */
|
|
catpt_updatel_shim(cdev, IMC, CATPT_IMC_IPCDB | CATPT_IMC_IPCCD, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int wpt_dsp_power_down(struct catpt_dev *cdev)
|
|
{
|
|
u32 mask, val;
|
|
|
|
/* disable core clock gating */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DCLCGE, 0);
|
|
|
|
catpt_dsp_reset(cdev, true);
|
|
/* set 24Mhz clock for both SSPs */
|
|
catpt_updatel_shim(cdev, CS1, CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1),
|
|
CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1));
|
|
catpt_dsp_select_lpclock(cdev, true, false);
|
|
/* disable MCLK */
|
|
catpt_updatel_shim(cdev, CLKCTL, CATPT_CLKCTL_SMOS, 0);
|
|
|
|
catpt_dsp_set_regs_defaults(cdev);
|
|
|
|
/* switch clock gating */
|
|
mask = CATPT_VDRTCTL2_CGEALL & (~CATPT_VDRTCTL2_DCLCGE);
|
|
val = mask & (~CATPT_VDRTCTL2_DTCGE);
|
|
catpt_updatel_pci(cdev, VDRTCTL2, mask, val);
|
|
/* enable DTCGE separatelly */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DTCGE,
|
|
CATPT_VDRTCTL2_DTCGE);
|
|
|
|
/* SRAM power gating all */
|
|
catpt_dsp_set_srampge(cdev, &cdev->dram, cdev->spec->dram_mask,
|
|
cdev->spec->dram_mask);
|
|
catpt_dsp_set_srampge(cdev, &cdev->iram, cdev->spec->iram_mask,
|
|
cdev->spec->iram_mask);
|
|
mask = WPT_VDRTCTL0_D3SRAMPGD | WPT_VDRTCTL0_D3PGD;
|
|
catpt_updatel_pci(cdev, VDRTCTL0, mask, WPT_VDRTCTL0_D3PGD);
|
|
|
|
catpt_updatel_pci(cdev, PMCS, PCI_PM_CTRL_STATE_MASK, PCI_D3hot);
|
|
/* give hw time to drop off */
|
|
udelay(50);
|
|
|
|
/* enable core clock gating */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DCLCGE,
|
|
CATPT_VDRTCTL2_DCLCGE);
|
|
udelay(50);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int wpt_dsp_power_up(struct catpt_dev *cdev)
|
|
{
|
|
u32 mask, val;
|
|
|
|
/* disable core clock gating */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DCLCGE, 0);
|
|
|
|
/* switch clock gating */
|
|
mask = CATPT_VDRTCTL2_CGEALL & (~CATPT_VDRTCTL2_DCLCGE);
|
|
val = mask & (~CATPT_VDRTCTL2_DTCGE);
|
|
catpt_updatel_pci(cdev, VDRTCTL2, mask, val);
|
|
|
|
catpt_updatel_pci(cdev, PMCS, PCI_PM_CTRL_STATE_MASK, PCI_D0);
|
|
|
|
/* SRAM power gating none */
|
|
mask = WPT_VDRTCTL0_D3SRAMPGD | WPT_VDRTCTL0_D3PGD;
|
|
catpt_updatel_pci(cdev, VDRTCTL0, mask, mask);
|
|
catpt_dsp_set_srampge(cdev, &cdev->dram, cdev->spec->dram_mask, 0);
|
|
catpt_dsp_set_srampge(cdev, &cdev->iram, cdev->spec->iram_mask, 0);
|
|
|
|
catpt_dsp_set_regs_defaults(cdev);
|
|
|
|
/* restore MCLK */
|
|
catpt_updatel_shim(cdev, CLKCTL, CATPT_CLKCTL_SMOS, CATPT_CLKCTL_SMOS);
|
|
catpt_dsp_select_lpclock(cdev, false, false);
|
|
/* set 24Mhz clock for both SSPs */
|
|
catpt_updatel_shim(cdev, CS1, CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1),
|
|
CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1));
|
|
catpt_dsp_reset(cdev, false);
|
|
|
|
/* enable core clock gating */
|
|
catpt_updatel_pci(cdev, VDRTCTL2, CATPT_VDRTCTL2_DCLCGE,
|
|
CATPT_VDRTCTL2_DCLCGE);
|
|
|
|
/* generate int deassert msg to fix inversed int logic */
|
|
catpt_updatel_shim(cdev, IMC, CATPT_IMC_IPCDB | CATPT_IMC_IPCCD, 0);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define CATPT_DUMP_MAGIC 0xcd42
|
|
#define CATPT_DUMP_SECTION_ID_FILE 0x00
|
|
#define CATPT_DUMP_SECTION_ID_IRAM 0x01
|
|
#define CATPT_DUMP_SECTION_ID_DRAM 0x02
|
|
#define CATPT_DUMP_SECTION_ID_REGS 0x03
|
|
#define CATPT_DUMP_HASH_SIZE 20
|
|
|
|
struct catpt_dump_section_hdr {
|
|
u16 magic;
|
|
u8 core_id;
|
|
u8 section_id;
|
|
u32 size;
|
|
};
|
|
|
|
int catpt_coredump(struct catpt_dev *cdev)
|
|
{
|
|
struct catpt_dump_section_hdr *hdr;
|
|
size_t dump_size, regs_size;
|
|
u8 *dump, *pos;
|
|
const char *eof;
|
|
char *info;
|
|
int i;
|
|
|
|
regs_size = CATPT_SHIM_REGS_SIZE;
|
|
regs_size += CATPT_DMA_COUNT * CATPT_DMA_REGS_SIZE;
|
|
regs_size += CATPT_SSP_COUNT * CATPT_SSP_REGS_SIZE;
|
|
dump_size = resource_size(&cdev->dram);
|
|
dump_size += resource_size(&cdev->iram);
|
|
dump_size += regs_size;
|
|
/* account for header of each section and hash chunk */
|
|
dump_size += 4 * sizeof(*hdr) + CATPT_DUMP_HASH_SIZE;
|
|
|
|
dump = vzalloc(dump_size);
|
|
if (!dump)
|
|
return -ENOMEM;
|
|
|
|
pos = dump;
|
|
|
|
hdr = (struct catpt_dump_section_hdr *)pos;
|
|
hdr->magic = CATPT_DUMP_MAGIC;
|
|
hdr->core_id = cdev->spec->core_id;
|
|
hdr->section_id = CATPT_DUMP_SECTION_ID_FILE;
|
|
hdr->size = dump_size - sizeof(*hdr);
|
|
pos += sizeof(*hdr);
|
|
|
|
info = cdev->ipc.config.fw_info;
|
|
eof = info + FW_INFO_SIZE_MAX;
|
|
/* navigate to fifth info segment (fw hash) */
|
|
for (i = 0; i < 4 && info < eof; i++, info++) {
|
|
/* info segments are separated by space each */
|
|
info = strnchr(info, eof - info, ' ');
|
|
if (!info)
|
|
break;
|
|
}
|
|
|
|
if (i == 4 && info)
|
|
memcpy(pos, info, min_t(u32, eof - info, CATPT_DUMP_HASH_SIZE));
|
|
pos += CATPT_DUMP_HASH_SIZE;
|
|
|
|
hdr = (struct catpt_dump_section_hdr *)pos;
|
|
hdr->magic = CATPT_DUMP_MAGIC;
|
|
hdr->core_id = cdev->spec->core_id;
|
|
hdr->section_id = CATPT_DUMP_SECTION_ID_IRAM;
|
|
hdr->size = resource_size(&cdev->iram);
|
|
pos += sizeof(*hdr);
|
|
|
|
memcpy_fromio(pos, cdev->lpe_ba + cdev->iram.start, hdr->size);
|
|
pos += hdr->size;
|
|
|
|
hdr = (struct catpt_dump_section_hdr *)pos;
|
|
hdr->magic = CATPT_DUMP_MAGIC;
|
|
hdr->core_id = cdev->spec->core_id;
|
|
hdr->section_id = CATPT_DUMP_SECTION_ID_DRAM;
|
|
hdr->size = resource_size(&cdev->dram);
|
|
pos += sizeof(*hdr);
|
|
|
|
memcpy_fromio(pos, cdev->lpe_ba + cdev->dram.start, hdr->size);
|
|
pos += hdr->size;
|
|
|
|
hdr = (struct catpt_dump_section_hdr *)pos;
|
|
hdr->magic = CATPT_DUMP_MAGIC;
|
|
hdr->core_id = cdev->spec->core_id;
|
|
hdr->section_id = CATPT_DUMP_SECTION_ID_REGS;
|
|
hdr->size = regs_size;
|
|
pos += sizeof(*hdr);
|
|
|
|
memcpy_fromio(pos, catpt_shim_addr(cdev), CATPT_SHIM_REGS_SIZE);
|
|
pos += CATPT_SHIM_REGS_SIZE;
|
|
|
|
for (i = 0; i < CATPT_SSP_COUNT; i++) {
|
|
memcpy_fromio(pos, catpt_ssp_addr(cdev, i),
|
|
CATPT_SSP_REGS_SIZE);
|
|
pos += CATPT_SSP_REGS_SIZE;
|
|
}
|
|
for (i = 0; i < CATPT_DMA_COUNT; i++) {
|
|
memcpy_fromio(pos, catpt_dma_addr(cdev, i),
|
|
CATPT_DMA_REGS_SIZE);
|
|
pos += CATPT_DMA_REGS_SIZE;
|
|
}
|
|
|
|
dev_coredumpv(cdev->dev, dump, dump_size, GFP_KERNEL);
|
|
|
|
return 0;
|
|
}
|