e57695e772
Those three new drivers were missed on the initial conversion to ReST format. So: - Rename them to .rst; - Add them to the hwmon index.rst index; - add some blank lines at the "Supported systems:" part, in order to allow Sphinx to properly identify new lines, suppressing warnings and avoid it to output some random lines in bold; - When multiple authors are involved, change the authors part to a list, in order to avoid adding blank lines. - adjust the table cells (one of the tables seemed to be assuming that tab is 4 positions instead of 8) and add the table markup. - be sure that the section markups have the same number of characters as the section title. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
81 lines
2.2 KiB
ReStructuredText
81 lines
2.2 KiB
ReStructuredText
Kernel driver isl68137
|
|
======================
|
|
|
|
Supported chips:
|
|
|
|
* Intersil ISL68137
|
|
|
|
Prefix: 'isl68137'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet:
|
|
|
|
Publicly available at the Intersil website
|
|
https://www.intersil.com/content/dam/Intersil/documents/isl6/isl68137.pdf
|
|
|
|
Authors:
|
|
- Maxim Sloyko <maxims@google.com>
|
|
- Robert Lippert <rlippert@google.com>
|
|
- Patrick Venture <venture@google.com>
|
|
|
|
Description
|
|
-----------
|
|
|
|
Intersil ISL68137 is a digital output 7-phase configurable PWM
|
|
controller with an AVSBus interface.
|
|
|
|
Usage Notes
|
|
-----------
|
|
|
|
This driver does not probe for PMBus devices. You will have to instantiate
|
|
devices explicitly.
|
|
|
|
The ISL68137 AVS operation mode must be enabled/disabled at runtime.
|
|
|
|
Beyond the normal sysfs pmbus attributes, the driver exposes a control attribute.
|
|
|
|
Additional Sysfs attributes
|
|
---------------------------
|
|
|
|
======================= ====================================
|
|
avs(0|1)_enable Controls the AVS state of each rail.
|
|
|
|
curr1_label "iin"
|
|
curr1_input Measured input current
|
|
curr1_crit Critical maximum current
|
|
curr1_crit_alarm Current critical high alarm
|
|
|
|
curr[2-3]_label "iout[1-2]"
|
|
curr[2-3]_input Measured output current
|
|
curr[2-3]_crit Critical maximum current
|
|
curr[2-3]_crit_alarm Current critical high alarm
|
|
|
|
in1_label "vin"
|
|
in1_input Measured input voltage
|
|
in1_lcrit Critical minimum input voltage
|
|
in1_lcrit_alarm Input voltage critical low alarm
|
|
in1_crit Critical maximum input voltage
|
|
in1_crit_alarm Input voltage critical high alarm
|
|
|
|
in[2-3]_label "vout[1-2]"
|
|
in[2-3]_input Measured output voltage
|
|
in[2-3]_lcrit Critical minimum output voltage
|
|
in[2-3]_lcrit_alarm Output voltage critical low alarm
|
|
in[2-3]_crit Critical maximum output voltage
|
|
in[2-3]_crit_alarm Output voltage critical high alarm
|
|
|
|
power1_label "pin"
|
|
power1_input Measured input power
|
|
power1_alarm Input power high alarm
|
|
|
|
power[2-3]_label "pout[1-2]"
|
|
power[2-3]_input Measured output power
|
|
|
|
temp[1-3]_input Measured temperature
|
|
temp[1-3]_crit Critical high temperature
|
|
temp[1-3]_crit_alarm Chip temperature critical high alarm
|
|
temp[1-3]_max Maximum temperature
|
|
temp[1-3]_max_alarm Chip temperature high alarm
|
|
======================= ====================================
|