a7f7f6248d
Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
51 lines
1.8 KiB
Plaintext
51 lines
1.8 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
config INFINIBAND_IPOIB
|
|
tristate "IP-over-InfiniBand"
|
|
depends on NETDEVICES && INET && (IPV6 || IPV6=n)
|
|
help
|
|
Support for the IP-over-InfiniBand protocol (IPoIB). This
|
|
transports IP packets over InfiniBand so you can use your IB
|
|
device as a fancy NIC.
|
|
|
|
See Documentation/infiniband/ipoib.rst for more information
|
|
|
|
config INFINIBAND_IPOIB_CM
|
|
bool "IP-over-InfiniBand Connected Mode support"
|
|
depends on INFINIBAND_IPOIB
|
|
default n
|
|
help
|
|
This option enables support for IPoIB connected mode. After
|
|
enabling this option, you need to switch to connected mode
|
|
through /sys/class/net/ibXXX/mode to actually create
|
|
connections, and then increase the interface MTU with
|
|
e.g. ifconfig ib0 mtu 65520.
|
|
|
|
WARNING: Enabling connected mode will trigger some packet
|
|
drops for multicast and UD mode traffic from this interface,
|
|
unless you limit mtu for these destinations to 2044.
|
|
|
|
config INFINIBAND_IPOIB_DEBUG
|
|
bool "IP-over-InfiniBand debugging" if EXPERT
|
|
depends on INFINIBAND_IPOIB
|
|
default y
|
|
help
|
|
This option causes debugging code to be compiled into the
|
|
IPoIB driver. The output can be turned on via the
|
|
debug_level and mcast_debug_level module parameters (which
|
|
can also be set after the driver is loaded through sysfs).
|
|
|
|
This option also creates a directory tree under ipoib/ in
|
|
debugfs, which contains files that expose debugging
|
|
information about IB multicast groups used by the IPoIB
|
|
driver.
|
|
|
|
config INFINIBAND_IPOIB_DEBUG_DATA
|
|
bool "IP-over-InfiniBand data path debugging"
|
|
depends on INFINIBAND_IPOIB_DEBUG
|
|
help
|
|
This option compiles debugging code into the data path
|
|
of the IPoIB driver. The output can be turned on via the
|
|
data_debug_level module parameter; however, even with output
|
|
turned off, this debugging code will have some performance
|
|
impact.
|