1bfcaa5700
Some usb controller drivers may not support extcon but use usb role class as it's the preferred approach, so to support usb dual role switch with usb role class, add usb role class consumer support. Signed-off-by: Li Jun <jun.li@nxp.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
193 lines
6.1 KiB
Plaintext
193 lines
6.1 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
menuconfig EXTCON
|
|
tristate "External Connector Class (extcon) support"
|
|
help
|
|
Say Y here to enable external connector class (extcon) support.
|
|
This allows monitoring external connectors by userspace
|
|
via sysfs and uevent and supports external connectors with
|
|
multiple states; i.e., an extcon that may have multiple
|
|
cables attached. For example, an external connector of a device
|
|
may be used to connect an HDMI cable and a AC adaptor, and to
|
|
host USB ports. Many of 30-pin connectors including PDMI are
|
|
also good examples.
|
|
|
|
if EXTCON
|
|
|
|
comment "Extcon Device Drivers"
|
|
|
|
config EXTCON_ADC_JACK
|
|
tristate "ADC Jack extcon support"
|
|
depends on IIO
|
|
help
|
|
Say Y here to enable extcon device driver based on ADC values.
|
|
|
|
config EXTCON_AXP288
|
|
tristate "X-Power AXP288 EXTCON support"
|
|
depends on MFD_AXP20X && USB_SUPPORT && X86 && ACPI && IOSF_MBI
|
|
select USB_ROLE_SWITCH
|
|
help
|
|
Say Y here to enable support for USB peripheral detection
|
|
and USB MUX switching by X-Power AXP288 PMIC.
|
|
|
|
config EXTCON_FSA9480
|
|
tristate "FSA9480 EXTCON Support"
|
|
depends on INPUT && I2C
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the Fairchild Semiconductor
|
|
FSA9480 microUSB switch and accessory detector chip. The FSA9480 is a USB
|
|
port accessory detector and switch. The FSA9480 is fully controlled using
|
|
I2C and enables USB data, stereo and mono audio, video, microphone
|
|
and UART data to use a common connector port.
|
|
|
|
config EXTCON_GPIO
|
|
tristate "GPIO extcon support"
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
Say Y here to enable GPIO based extcon support. Note that GPIO
|
|
extcon supports single state per extcon instance.
|
|
|
|
config EXTCON_INTEL_INT3496
|
|
tristate "Intel INT3496 ACPI device extcon driver"
|
|
depends on GPIOLIB && ACPI && (X86 || COMPILE_TEST)
|
|
help
|
|
Say Y here to enable extcon support for USB OTG ports controlled by
|
|
an Intel INT3496 ACPI device.
|
|
|
|
This ACPI device is typically found on Intel Baytrail or Cherrytrail
|
|
based tablets, or other Baytrail / Cherrytrail devices.
|
|
|
|
config EXTCON_INTEL_CHT_WC
|
|
tristate "Intel Cherrytrail Whiskey Cove PMIC extcon driver"
|
|
depends on INTEL_SOC_PMIC_CHTWC
|
|
depends on USB_SUPPORT
|
|
select USB_ROLE_SWITCH
|
|
help
|
|
Say Y here to enable extcon support for charger detection / control
|
|
on the Intel Cherrytrail Whiskey Cove PMIC.
|
|
|
|
config EXTCON_INTEL_MRFLD
|
|
tristate "Intel Merrifield Basin Cove PMIC extcon driver"
|
|
depends on INTEL_SOC_PMIC_MRFLD
|
|
help
|
|
Say Y here to enable extcon support for charger detection / control
|
|
on the Intel Merrifield Basin Cove PMIC.
|
|
|
|
config EXTCON_MAX14577
|
|
tristate "Maxim MAX14577/77836 EXTCON Support"
|
|
depends on MFD_MAX14577
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX14577/77836. The MAX14577/77836 MUIC is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_MAX3355
|
|
tristate "Maxim MAX3355 USB OTG EXTCON Support"
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
If you say yes here you get support for the USB OTG role detection by
|
|
MAX3355. The MAX3355 chip integrates a charge pump and comparators to
|
|
enable a system with an integrated USB OTG dual-role transceiver to
|
|
function as an USB OTG dual-role device.
|
|
|
|
config EXTCON_MAX77693
|
|
tristate "Maxim MAX77693 EXTCON Support"
|
|
depends on MFD_MAX77693 && INPUT
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX77693 PMIC. The MAX77693 MUIC is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_MAX77843
|
|
tristate "Maxim MAX77843 EXTCON Support"
|
|
depends on MFD_MAX77843
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX77843. The MAX77843 MUIC is a USB port accessory
|
|
detector add switch.
|
|
|
|
config EXTCON_MAX8997
|
|
tristate "Maxim MAX8997 EXTCON Support"
|
|
depends on MFD_MAX8997 && IRQ_DOMAIN
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Maxim MAX8997 PMIC. The MAX8997 MUIC is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_PALMAS
|
|
tristate "Palmas USB EXTCON support"
|
|
depends on MFD_PALMAS
|
|
help
|
|
Say Y here to enable support for USB peripheral and USB host
|
|
detection by palmas usb.
|
|
|
|
config EXTCON_PTN5150
|
|
tristate "NXP PTN5150 CC LOGIC USB EXTCON support"
|
|
depends on I2C && (GPIOLIB || COMPILE_TEST)
|
|
depends on USB_ROLE_SWITCH || !USB_ROLE_SWITCH
|
|
select REGMAP_I2C
|
|
help
|
|
Say Y here to enable support for USB peripheral and USB host
|
|
detection by NXP PTN5150 CC (Configuration Channel) logic chip.
|
|
|
|
config EXTCON_QCOM_SPMI_MISC
|
|
tristate "Qualcomm USB extcon support"
|
|
depends on ARCH_QCOM || COMPILE_TEST
|
|
help
|
|
Say Y here to enable SPMI PMIC based USB cable detection
|
|
support on Qualcomm PMICs such as PM8941.
|
|
|
|
config EXTCON_RT8973A
|
|
tristate "Richtek RT8973A EXTCON support"
|
|
depends on I2C
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
select REGMAP_IRQ
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Richtek RT8973A. The RT8973A is a USB port accessory detector
|
|
and switch that is optimized to protect low voltage system
|
|
from abnormal high input voltage (up to 28V).
|
|
|
|
config EXTCON_SM5502
|
|
tristate "Silicon Mitus SM5502/SM5504/SM5703 EXTCON support"
|
|
depends on I2C
|
|
select IRQ_DOMAIN
|
|
select REGMAP_I2C
|
|
select REGMAP_IRQ
|
|
help
|
|
If you say yes here you get support for the MUIC device of
|
|
Silicon Mitus SM5502. The SM5502 is a USB port accessory
|
|
detector and switch.
|
|
|
|
config EXTCON_USB_GPIO
|
|
tristate "USB GPIO extcon support"
|
|
depends on GPIOLIB || COMPILE_TEST
|
|
help
|
|
Say Y here to enable GPIO based USB cable detection extcon support.
|
|
Used typically if GPIO is used for USB ID pin detection.
|
|
|
|
config EXTCON_USBC_CROS_EC
|
|
tristate "ChromeOS Embedded Controller EXTCON support"
|
|
depends on CROS_EC
|
|
help
|
|
Say Y here to enable USB Type C cable detection extcon support when
|
|
using Chrome OS EC based USB Type-C ports.
|
|
|
|
config EXTCON_USBC_TUSB320
|
|
tristate "TI TUSB320 USB-C extcon support"
|
|
depends on I2C
|
|
select REGMAP_I2C
|
|
help
|
|
Say Y here to enable support for USB Type C cable detection extcon
|
|
support using a TUSB320.
|
|
|
|
endif
|