84e0cdb0a2
Both at91 and avr32 defines its own platform data structure for the macb driver and both share common structures though at91 includes a currently unused phy_irq_pin. Create a common macb_platform_data for macb that both at91 and avr32 can use. In future we can use this to support other architectures that use the same IP block with the macb driver. v2: rename eth_platform_data to macb_platform_data and allow at91_ether to share the platform data with macb. Signed-off-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
351 lines
7.7 KiB
C
351 lines
7.7 KiB
C
/*
|
|
* linux/arch/arm/mach-at91/board-sam9260ek.c
|
|
*
|
|
* Copyright (C) 2005 SAN People
|
|
* Copyright (C) 2006 Atmel
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
|
|
*/
|
|
|
|
#include <linux/types.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/init.h>
|
|
#include <linux/mm.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/spi/at73c213.h>
|
|
#include <linux/clk.h>
|
|
#include <linux/i2c/at24.h>
|
|
#include <linux/gpio_keys.h>
|
|
#include <linux/input.h>
|
|
|
|
#include <asm/setup.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/irq.h>
|
|
|
|
#include <asm/mach/arch.h>
|
|
#include <asm/mach/map.h>
|
|
#include <asm/mach/irq.h>
|
|
|
|
#include <mach/hardware.h>
|
|
#include <mach/board.h>
|
|
#include <mach/at91sam9_smc.h>
|
|
#include <mach/at91_shdwc.h>
|
|
#include <mach/system_rev.h>
|
|
|
|
#include "sam9_smc.h"
|
|
#include "generic.h"
|
|
|
|
|
|
static void __init ek_init_early(void)
|
|
{
|
|
/* Initialize processor: 18.432 MHz crystal */
|
|
at91_initialize(18432000);
|
|
|
|
/* DBGU on ttyS0. (Rx & Tx only) */
|
|
at91_register_uart(0, 0, 0);
|
|
|
|
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
|
|
at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
|
|
| ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
|
|
| ATMEL_UART_RI);
|
|
|
|
/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
|
|
at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
|
|
|
|
/* set serial console to ttyS0 (ie, DBGU) */
|
|
at91_set_serial_console(0);
|
|
}
|
|
|
|
/*
|
|
* USB Host port
|
|
*/
|
|
static struct at91_usbh_data __initdata ek_usbh_data = {
|
|
.ports = 2,
|
|
};
|
|
|
|
/*
|
|
* USB Device port
|
|
*/
|
|
static struct at91_udc_data __initdata ek_udc_data = {
|
|
.vbus_pin = AT91_PIN_PC5,
|
|
.pullup_pin = 0, /* pull-up driven by UDC */
|
|
};
|
|
|
|
|
|
/*
|
|
* Audio
|
|
*/
|
|
static struct at73c213_board_info at73c213_data = {
|
|
.ssc_id = 0,
|
|
.shortname = "AT91SAM9260-EK external DAC",
|
|
};
|
|
|
|
#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
|
|
static void __init at73c213_set_clk(struct at73c213_board_info *info)
|
|
{
|
|
struct clk *pck0;
|
|
struct clk *plla;
|
|
|
|
pck0 = clk_get(NULL, "pck0");
|
|
plla = clk_get(NULL, "plla");
|
|
|
|
/* AT73C213 MCK Clock */
|
|
at91_set_B_periph(AT91_PIN_PC1, 0); /* PCK0 */
|
|
|
|
clk_set_parent(pck0, plla);
|
|
clk_put(plla);
|
|
|
|
info->dac_clk = pck0;
|
|
}
|
|
#else
|
|
static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
|
|
#endif
|
|
|
|
/*
|
|
* SPI devices.
|
|
*/
|
|
static struct spi_board_info ek_spi_devices[] = {
|
|
#if !defined(CONFIG_MMC_AT91)
|
|
{ /* DataFlash chip */
|
|
.modalias = "mtd_dataflash",
|
|
.chip_select = 1,
|
|
.max_speed_hz = 15 * 1000 * 1000,
|
|
.bus_num = 0,
|
|
},
|
|
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
|
|
{ /* DataFlash card */
|
|
.modalias = "mtd_dataflash",
|
|
.chip_select = 0,
|
|
.max_speed_hz = 15 * 1000 * 1000,
|
|
.bus_num = 0,
|
|
},
|
|
#endif
|
|
#endif
|
|
#if defined(CONFIG_SND_AT73C213) || defined(CONFIG_SND_AT73C213_MODULE)
|
|
{ /* AT73C213 DAC */
|
|
.modalias = "at73c213",
|
|
.chip_select = 0,
|
|
.max_speed_hz = 10 * 1000 * 1000,
|
|
.bus_num = 1,
|
|
.mode = SPI_MODE_1,
|
|
.platform_data = &at73c213_data,
|
|
},
|
|
#endif
|
|
};
|
|
|
|
|
|
/*
|
|
* MACB Ethernet device
|
|
*/
|
|
static struct macb_platform_data __initdata ek_macb_data = {
|
|
.phy_irq_pin = AT91_PIN_PA7,
|
|
.is_rmii = 1,
|
|
};
|
|
|
|
|
|
/*
|
|
* NAND flash
|
|
*/
|
|
static struct mtd_partition __initdata ek_nand_partition[] = {
|
|
{
|
|
.name = "Partition 1",
|
|
.offset = 0,
|
|
.size = SZ_256K,
|
|
},
|
|
{
|
|
.name = "Partition 2",
|
|
.offset = MTDPART_OFS_NXTBLK,
|
|
.size = MTDPART_SIZ_FULL,
|
|
},
|
|
};
|
|
|
|
static struct atmel_nand_data __initdata ek_nand_data = {
|
|
.ale = 21,
|
|
.cle = 22,
|
|
// .det_pin = ... not connected
|
|
.rdy_pin = AT91_PIN_PC13,
|
|
.enable_pin = AT91_PIN_PC14,
|
|
.parts = ek_nand_partition,
|
|
.num_parts = ARRAY_SIZE(ek_nand_partition),
|
|
};
|
|
|
|
static struct sam9_smc_config __initdata ek_nand_smc_config = {
|
|
.ncs_read_setup = 0,
|
|
.nrd_setup = 1,
|
|
.ncs_write_setup = 0,
|
|
.nwe_setup = 1,
|
|
|
|
.ncs_read_pulse = 3,
|
|
.nrd_pulse = 3,
|
|
.ncs_write_pulse = 3,
|
|
.nwe_pulse = 3,
|
|
|
|
.read_cycle = 5,
|
|
.write_cycle = 5,
|
|
|
|
.mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
|
|
.tdf_cycles = 2,
|
|
};
|
|
|
|
static void __init ek_add_device_nand(void)
|
|
{
|
|
ek_nand_data.bus_width_16 = board_have_nand_16bit();
|
|
/* setup bus-width (8 or 16) */
|
|
if (ek_nand_data.bus_width_16)
|
|
ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
|
|
else
|
|
ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
|
|
|
|
/* configure chip-select 3 (NAND) */
|
|
sam9_smc_configure(3, &ek_nand_smc_config);
|
|
|
|
at91_add_device_nand(&ek_nand_data);
|
|
}
|
|
|
|
|
|
/*
|
|
* MCI (SD/MMC)
|
|
*/
|
|
static struct at91_mmc_data __initdata ek_mmc_data = {
|
|
.slot_b = 1,
|
|
.wire4 = 1,
|
|
// .det_pin = ... not connected
|
|
// .wp_pin = ... not connected
|
|
// .vcc_pin = ... not connected
|
|
};
|
|
|
|
|
|
/*
|
|
* LEDs
|
|
*/
|
|
static struct gpio_led ek_leds[] = {
|
|
{ /* "bottom" led, green, userled1 to be defined */
|
|
.name = "ds5",
|
|
.gpio = AT91_PIN_PA6,
|
|
.active_low = 1,
|
|
.default_trigger = "none",
|
|
},
|
|
{ /* "power" led, yellow */
|
|
.name = "ds1",
|
|
.gpio = AT91_PIN_PA9,
|
|
.default_trigger = "heartbeat",
|
|
}
|
|
};
|
|
|
|
/*
|
|
* I2C devices
|
|
*/
|
|
static struct at24_platform_data at24c512 = {
|
|
.byte_len = SZ_512K / 8,
|
|
.page_size = 128,
|
|
.flags = AT24_FLAG_ADDR16,
|
|
};
|
|
|
|
static struct i2c_board_info __initdata ek_i2c_devices[] = {
|
|
{
|
|
I2C_BOARD_INFO("24c512", 0x50),
|
|
.platform_data = &at24c512,
|
|
},
|
|
/* more devices can be added using expansion connectors */
|
|
};
|
|
|
|
|
|
/*
|
|
* GPIO Buttons
|
|
*/
|
|
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
|
|
static struct gpio_keys_button ek_buttons[] = {
|
|
{
|
|
.gpio = AT91_PIN_PA30,
|
|
.code = BTN_3,
|
|
.desc = "Button 3",
|
|
.active_low = 1,
|
|
.wakeup = 1,
|
|
},
|
|
{
|
|
.gpio = AT91_PIN_PA31,
|
|
.code = BTN_4,
|
|
.desc = "Button 4",
|
|
.active_low = 1,
|
|
.wakeup = 1,
|
|
}
|
|
};
|
|
|
|
static struct gpio_keys_platform_data ek_button_data = {
|
|
.buttons = ek_buttons,
|
|
.nbuttons = ARRAY_SIZE(ek_buttons),
|
|
};
|
|
|
|
static struct platform_device ek_button_device = {
|
|
.name = "gpio-keys",
|
|
.id = -1,
|
|
.num_resources = 0,
|
|
.dev = {
|
|
.platform_data = &ek_button_data,
|
|
}
|
|
};
|
|
|
|
static void __init ek_add_device_buttons(void)
|
|
{
|
|
at91_set_gpio_input(AT91_PIN_PA30, 1); /* btn3 */
|
|
at91_set_deglitch(AT91_PIN_PA30, 1);
|
|
at91_set_gpio_input(AT91_PIN_PA31, 1); /* btn4 */
|
|
at91_set_deglitch(AT91_PIN_PA31, 1);
|
|
|
|
platform_device_register(&ek_button_device);
|
|
}
|
|
#else
|
|
static void __init ek_add_device_buttons(void) {}
|
|
#endif
|
|
|
|
|
|
static void __init ek_board_init(void)
|
|
{
|
|
/* Serial */
|
|
at91_add_device_serial();
|
|
/* USB Host */
|
|
at91_add_device_usbh(&ek_usbh_data);
|
|
/* USB Device */
|
|
at91_add_device_udc(&ek_udc_data);
|
|
/* SPI */
|
|
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
|
|
/* NAND */
|
|
ek_add_device_nand();
|
|
/* Ethernet */
|
|
at91_add_device_eth(&ek_macb_data);
|
|
/* MMC */
|
|
at91_add_device_mmc(0, &ek_mmc_data);
|
|
/* I2C */
|
|
at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
|
|
/* SSC (to AT73C213) */
|
|
at73c213_set_clk(&at73c213_data);
|
|
at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
|
|
/* LEDs */
|
|
at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
|
|
/* Push Buttons */
|
|
ek_add_device_buttons();
|
|
}
|
|
|
|
MACHINE_START(AT91SAM9260EK, "Atmel AT91SAM9260-EK")
|
|
/* Maintainer: Atmel */
|
|
.timer = &at91sam926x_timer,
|
|
.map_io = at91_map_io,
|
|
.init_early = ek_init_early,
|
|
.init_irq = at91_init_irq_default,
|
|
.init_machine = ek_board_init,
|
|
MACHINE_END
|